Industrial Media Converter User Manual
Contents
1. please contact the local dealer for service Physical Dimension 10 100Base TX to 100Base FX Industrial Media Converter dimension W x D x H is 59mm x 50mm x 36mm Front View S de View Din Rail SFP type LED Indicators Green ON TX link is detected Flashing TX data is Power ON Power is detected Fiber port Link Active Amber ON fiber is detected ON 100M speed is detected Flashing data is transmitting OFF 10M speed is detected Dip switch function This unit is equipped with dip switches located on the front panel marked as SW1 Adjusting the dip switches will change the default function of this unit This unit has set to manufacturer default as switch mode and LFP function off The table shown as you may change the dip switch setting to your desired environment On Teonvertermode a DIP 1 Switch mode default OFF SW1 ON LFP function enabled LFP function disabled default Wiring the Power Inputs This unit provides 3 pin terminal block And it can be operated using either VAC or VDC power source The VDC power range is from 12VDC to 60VDC and the VAC power range is from 18VAC to 36VAC Always Make sure your input voltage is within this supported voltage range WARNING Any exceeded input voltage will not make this unit function and may damage this unit To make power connection Follow the printed polarity for V V ground Connect positive wire to V conne2. Industrial Media Converter User Manual V1 00 FCC MARKING This Equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 ofthe FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CE MARKING This equipment complies with the requirements relating to electromagnetic compatibility EN 55022 class A for ITE the essential protection requirement of Council Directive 2004 108 EC on the approximation of the laws of the Member States relating to electromagnetic compatibility Company has an on going policy of upgrading its products and it may be possible that information in this document is not up to date Please check with your local distributors fo
3. ck EC 60068 2 27 ss Freefall IEC 60068 2 32 S 4
4. ct negative wire to V also connect neutral wire to ground Connecting procedure STEP 1 Pull out 3 pin terminal block STEP 2 Connect wire to V V and Ground STEP 3 Connect SFP fiber connector or SC fiber wire to fiber port L STEP 4 plug back 3 pin terminal block to its place Ve gt Y t t a Y y WARNING Always pull out terminal block to connect power wire DO NOT force SFP fiber into SFP housing without removing terminal block Specification IEEE 802 3 10Base T Ethernet IEEE 802 3u 100Base TX Fast Ethernet IEEE Standard IEEE 802 3u 100Base FX Fast Ethernet IEEE802 3x Flow Control and Back Pressure Data Processing Store and Forward Flow Control IEEE 802 3x Flow Control and Back Pressure Transparent conversion to 802 1Q VLAN tagged packets RJ 45 Port 10 100M BaseT X Auto negotiation Auto MDI MDI X Network Connector function Full Half duplex Fiber port 100BaseFX SC ST SC SM 30km SFP 100BaseX Power Speed Link Act LED indicators Speed TP port Link Act TP and Fiber port DIPSwith Link Fault Pass Through LFP Converter Mode Switch Mode 18V 36VAC Power Input 12V 60VDC DC Jack terminal cable supported DC Barrel Connector 5 to 95 Non condensing Panel Mounted Ea CE EN 55022 Class A EN61000 4 2 ESD Level 3 EN61000 4 3 RS EN61000 4 4 EFT Level 2 EN61000 4 5 Surge Level 2 EN61000 4 6 CS Level 2 Level 2 EN 61000 4 8 PFMF Level 1 Sho
5. r the latest information No part of this document can be copied or reproduced in any form without written consent from the company Trademarks All trade names and trademarks are the properties of their respective companies Copyright 2013 All Rights Reserved P N 41RP IMC60100 AQG Introduction This true mini rugged Industrial media converter is designed for where critical but space limited outdoor CAM enclosure It can be powered by wide range of VAC VDC or external DC power adapter With its multi purpose design it can also be used for Din Rail or wall mounted It is an ideal unit for IP surveillance traffic monitoring and Security application in critical environment It can tolerate 40 C to 75 C in harsh environment to perform a reliable network Key Features True Mini rugged design enclosure Supports 18V 36VAC 12V 60VDC or DC Jack socket Supports Link Fault Pass through LFP function Supports switch model and converter mode Surge protection diodes on power input ESD protection diodes on RJ 45 port Provides Far End Fault function on FX port Provides increased Noise Immunity Extended environmental specification 40 C to 75 C Package Contents m 1x Industrial Media converter 1x User Manual 1 x 3 pin Terminal Block 2 x Wall Mounting Bracket and 4 x Screws 1 x Din Rail Bracket Compare the contents of the industrial switch with the standard checklist above If any item is damaged or missing
Download Pdf Manuals
Related Search