Descaling VBM Double Boiler
Contents
1. THE ITALIAN TOUGH IN THE HEART OF OREGON DESCALING a Vibiemme DOUBLE DOMO Descaling should be performed by an authorized espresso machine technician However should you feel technically competent to descale your espresso machine these instructions can be used in conjunction with your user s manual and the descaler manufacturer s instructions to help you complete the process correctly Please read this thoroughly before attempting to complete the cleaning process If you do not feel comfortable with any step of the process please hire a professional Stefano s Espresso Care is not responsible for any damage to your equipment your property or your person during or resulting from this cleaning process Descaling is preventative maintenance that will prolong the life of your espresso machine As boiling water turns to steam mineral content leaves behind hard water deposits which can cause multiple problems in your espresso machine such as Water sensor malfunction and failure Heating element failure Clogged thermosyphon pipes Low brewing volume Poor pressurestat response Low temperature grouphead Drips and leaks from the grouphead Inability to form pressure in the boiler due to vacuum breaker failure VVVVVVVV Depending on the mineral content of your water and frequency of use your machine should be descaled approximately four times a year Warning Descaling involves pumping a chemical solution through the machine2. These special chemicals usually contain a food grade acid that can be hazardous Carefully follow the manufacturer s recommendations and use safety precautions Even when working carefully some solution may splash in your work area Eye protection and gloves are required when handling and using these chemicals Do not allow bystanders in the area unless they are properly protected You must also protect the work area both under and around your espresso machine Immediately wash off any splashes particularly on painted surfaces Do not touch your skin or eyes during this process as descaler can cause serious irritation and burns to sensitive tissue Warning Descaling involves opening the case of the machine and exposing internal components Electrical components and their wiring can present a shock hazard Many parts inside the machine get hot enough to cause severe burns so USE EXTREME CAUTION Warning Only use products manufactured explicitly for scale removal in espresso machine boilers Other products such as those made for cleaning coffee pots or removing hard water scale from bathrooms must never be used Never use vinegar or any other chemicals for this purpose Never add any other cleaning agent to your water tank Always follow the manufacturer s recommendation and instructions when descaling an espresso machine Use of improper cleaners or improperly using the correct cleaner can void the warranty damage your espresso machine and b
3. the one minute pump procedure pump clean water into the boiler allowing solution to exit from the steam wand Continue until the 2 5 liters are gone 17 Turn the machine OFF UNPLUG THE MACHINE To remove any remaining scale from the water level probe loosen the small nut that holds the probe in place pull the probe out and wipe it clean Reinstall the probe making sure it is at the same level as before and reconnect the wire 18 Refill your container with fresh clean water plug the machine in and turn to position II Wait for the pressure to build again quickly open and close the steam valve to let the false pressure out Once the left light is off turn switch to position I place a container under the hot water spout and open the hot water knob Allow water to flow out until the pump starts 19 As soon as the pump activates turn the hot water knob off When the pump stops the normal water level inside the boiler is reached 20 Turn the machine off UNPLUt vacuum valve THE MACHINE Remove the wire tie from the anti 21 Plug in machine turn on to position I Turn the PID on Turn switch on position II and wait for both pressure and temperature to build 22 Check for any anomalies leaks etc 23 Turn the machine off UNPLUG THE MACHINE Remove the microswitch jumper reconnect the microswitch wires and reassemble the unit After all the pieces are back in place it is recommended to pull and dump a
4. e harmful to your health WARNING Do not leave the machine unattended during this process except when the machine is OFF or unplugged For your convenience we now offer a Descaling Kit which can be purchase from our web page the kit includes 4 packets of pulycaff baby descaler 2 packets of pulycaff espresso cleaner 1 pre assembled jumper cable Since your machine has 2 separate boilers we will cover the procedure one boiler at a time starting with the brew boiler The brew boiler works by displacement water from the boiler exits the grouphead as fresh water enters the boiler BREW BOILER DESCALING PROCESS Before starting this process thoroughly backflush the grouphead with a suitable espresso machine cleaner 1 Prepare the descaling solution in a container Following the descaling agent manufacturer instructions to make approximately 2 5 liters of solution The powder dissolves better in hot water but the solution must cool to room temperature before you add it to the reservoir To expedite this process start by dissolving the powder in approximately one liter of hot water and then add enough cold water to reach the proper ratio Once the solution is cool use it to fill the water reservoir at least 1 4 full 2 UNPLUG THE MACHINE Remove drip tray grate and cup warming tray Remove the side back casing 3 screws on each side Remove the water reservoir unscrew the 2 bottom screws that hold the reservoir plate divide
5. few shots of espresso and froth a few pitchers of water to clean the descaler s aftertaste 24 Your machine is now descaled WARNING Most proper descalers are a form of food grade citric acid and are safe to consume when highly diluted CAUTIO Failure to reconnect the autofill wire or enable the vacuum breaker will cause your machine to behave erratically and can cause damage not covered by the warranty Questions Contact us at service espressocare com
6. hoses as pictured on page 3 brew boiler instructions Turn machine on to position H and wait for steam pressure to reach the pre set pressure 2 Once the pressurestat clicks and the left light goes off turn the switch to the OFF position UNPLUG THE MACHINE Place a container under the hot water spout and open the valve Keep the valve open until water stops flowing and then close Caution the water is boiling hot Remove the steam wand tip paying attention to the Teflon O Ring some versions have a small Teflon disk inside the tip take care not to lose it as well as the hot water spout tip and all its inside parts Open the steam valve Locate the level probe sensor on top of the steam boiler see picture below and MARK THE EXPOSED HEIGHT COMING OUT FROM THE NUT Disconnect the connector with a small flat blade screwdriver by loosening the screw on the sensor rod end inside the plastic housing shown in the picture Do not disconnect the screw on the wire end Removing the connector indicates a low water level in the boiler and it needs to be refilled Set it aside where it cannot accidentally touch any metal parts Locate the anti vacuum valve see picture ANTI VACUUM VALVE AND LEVEL PROBE LOCATION Lift the center plunger of the anti vacuum valve with your finger and tie a wire tie between the clip and the flat part of the valve so that the valve stays UP closed This will prevent liquid from escaping f
7. ocess the one minute interval is recommended by the pump manufacturer Continue until most of the solution has been drawn into the boiler 7 Insert the backflush basket and activate the lever Allow 2 3 ounces of water to flow from the bypass valve into the empty container and stop the lever 8 Allow the machine to sit for at least one hour while the descaling solution works on buildup inside the boiler Refer to descaling agent instructions for indications of how long this should take The soaking time required is governed by the mineral content of your water how often you use your machine and how long since it was last descaled 9 After the necessary time has passed rinse the solution container fill it with 2 5 liters of clean fresh water Insert the pump hose and flush clean water out of the grouphead following the one minute on one minute off procedure 10 While descaling solution is coming out the water will appear bluish and murky Flush about 2 liters of clean water through the boiler until it is crystal clear Repeat the backflush allowing also 2 3 ounces of water to flow from the bypass hose 11 Your boiler is now descaled flushed and filled with clean water Note that a slight taste and smell of descaler may be present for a while longer 12 Turn the PID off push and hold the right button until the LCD displays OFF STEAM BOILER DESCALING 1 Prepare another 2 5 liters of descaling solution and position the
8. r in place located on the bottom back part of the chassis Unscrew the 2 screws below the cup warming tray Locate the reservoir microswitch mark wire positions and remove them from the microswitch Set the plate divider aside Use an insulated 12 gauge jumper wire to connect the 2 black wires Set the purple wire aside Ensure the jumper is insulated and no metal parts are touched see picture below MICROSWITCH JUMPER LOCATION 3 If the machine is so equipped remove the in tank water softener not the filter screen and install the original filter screen that fits the end of the hose The descaling agent will permanently damage the water softener if it is left in place during this process so do not reinstall it until this entire procedure is completed The original filter screen will stop any foreign matter from entering the boilers Position the inlet hose the one that goes to the pump inside the solution container and place the bypass hose in a suitable container 4 Plug machine in and turn on position I While the PID brings the water up to operating temperature reposition the drip tray in its proper location under the grouphead 5 Once the set temperature is reached activate the lever and let the water flow out of the group for NO MORE than one minute Use the on off switch to turn the pump on and off Caution water will be boiling hot 6 Let sit for one minute to allow the vibrating pump to cool and repeat pr
9. rom the valve as you complete this process 10 1 13 ANTI VACUUM WITH WIRE TIE AROUND IT Position a container under the steam wand and open the valve Plug the machine in and turn the power switch to position I which keeps the steam heating element safe from exposure The autofill is defeated therefore the machine will overfill completely fill the boiler Once the steam valve level is reached the liquid will exit from the steam wand At this point close the steam valve and turn the machine OFF Again follow the one minute rule for the pump UNPLUG THE MACHINE and reconnect the level probe Plug the machine in and turn to position H wait for the machine to heat up and reach the pre set temperature Keep monitoring the wire tie on the anti vacuum valve MAKE SURE it remains secure or water will leak and splatter Once the boiler is at pressure momentarily open and close the steam valve a couple of times to let out false pressure Let the solution sit in the boiler for at least one hour Rinse the container and fill with 2 5 liters of clean fresh water Turn off the machine Place a container under the hot water spout and open the hot water valve until no more water exits Turn the knob off 14 UNPLUG THE MACHINE Disconnect the autofill probe 15 Open the steam valve knob 16 Plug the machine in and turn switch to position I The pump will engage and clean water will flow into the boiler Following
Download Pdf Manuals
Related Search