Page 1 Meat Slicer Series Users` Manual Page 2 Honorific customer
Contents
1. 7 handle of the food pressing board Load the dish and support modules Bolt M6 with shpe groove Cap shape net M6 hand handle Attention assemble the hand handle blocks the plank bottom to face to want and load the dish parallelism 38 The WED B250B 2 WED B300B 2 installs the module diagram Press to anticipate the plank B O form rubber turn Lead the pole Small support B Hand handle Hexangular screw inside the M6 Install the method 1 Will press to anticipate the plank B set first in leading the pole then the both ends that a difference of two O s form rubber set is leading the pole 2 Will lead the both ends of the pole the set is in small support AN and the bore of the small support Bs respectively then use the screw of M6 to fix the small support B good 39 The poly V belt adjust hexagonal screw M6 nut A M6 nut B When the poly V belt has got loose first and upward loosen the M6 nut A then adjust the M6 nut B upwards until the elasticity of the poly V belt adjust to be suitable If the poly V belt is too tightly the adjustment then is contrary 40 Automatic body oiling schematic diagram The vent valve is close while the meat slicer in transportation open it while the meat slicer use Reducer oiling hole Oil lens Swing bar oiling hole 41 Automatic stainless steel body to disassemble of method P2. 010 spring washer p8 quickly deal with contact keep right angel connector M10x1 hexagon socket cap screws M6x15 plastic feet A hexagon socket cap screws M10x35 Components list automatic body 480x380 621 base 475x184 driven pulley 100 20 622 505 center deviating wheel swing bar L 340 623 motor 450W 624 classical V belt A700 625 the big cover M6 screw 628 602 the support fixs the set 638 603 the slippery piece fixs the set 701 lock the stalk from lock screw M10 702 606 the stalk blocks the inside of circle path 703 with the flexibility 923 2 704 607 Path inside the spring coil 18 5x1x30 608 clip fixedly 705 609 tiny move the switch 706 610 hexagon socket cap screws M3 x15 611 loadstone 707 612 loadstone set 708 613 the magnetic field responds the switch 614 pan head screws with cross recessed 709 M3 x8 710 615 616 617 low pressure circuit board AC outlet Cross recessed countersunk head screw M3 x 8 the stainless steel takes 220 x10 618 619 620 round head rivets p3 x 5 axle of the frame of the grinding parts 12x62 axle of the frame of the grinding parts 12x74 axle of the frame of the grinding parts 12 80 sliding 200 1 sliding 250 3 sliding part 300B1 I the stainless steel takes 260 x10 the stainless steel takes 320 x10 fixing screw of the protecting cover of the slicing knife 8
3. M6x10 hexagon flange nuts M5 fixing bolt M5x30 connecting cushion of the motor motor 210W poly V belt 320 wire and plug fixing clamp of the wire fix position of Relays belt to tight the wire relays JQX 13F electric capacitor SF pan head screws with cross recessed 4 10 Switch base board 338x238 plastic feet B cap nut M6 slotted countersund head screws M6x25 spring washer 96 hexagonal screw M6x50 the hand handle blocks the plankp65 Hexangular aluminum stick12 Protect knife dish copper nut M6 whole frame of model 250 food stopping board of model 250 board base cover of the branch base food carrier 230x230 small frame A 29 Components list small frame guiding stick of the food pressing board 910x215 O shape rubber band 14 position fixing aluminum belt pan head screws with cross recessed M6x15 food pressing board of model 250 A copper set 1412 big pentagonal handle sliding part small frame C of model 250 hexagon socket set screws withflatpoint M6x25 ame of model 250 A handle of the frame aluminum flat cushion of small frame C sliding part 940x130 food pressing board of model 250B supporting square axle L 328 food pressing stick of model 250 aluminum pressing cover guiding axle of the sliding part 20 390 spring inner diameterp20 5 frame of model 250 B copper set inner diameter 2025 hexagonal screw M8x20 O shape rubber band M20 D adju
4. cross recessed countersunk head screw M5x16 protecting ring of the slicing knife 9237 5 main axle of the slicing knife L 157 belt pulley of razor blade 960 ball bearing 6004 2RS hole elastic outer diameter 050 axle elastic outer diameter 918 frame of the grinding parts of model 200 grinding wheel base protecting cover of the grinding wheel 28 Components list 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 173 171 172 173 174 175 176 fixing handle of the frame of the grinding parts hexagonal screw M8x25 plain washers 98 pan head screws with cross recessed 5 25 axle of the frame of the grinding parts 912 knife repairing axle of the grinding wheel p10x70 handle of the grinding wheel plain washers 96 spring innerdiameterp6 5X0 6X20 copper set of the grinding wheel base 912 grinding axle of the grinding wheel 910 73 grinding wheel 940 nut M6 axle elastic 5 pan head screws with cross recessed M5x10 adjusting handle of the frame of the grinding parts nut M5 plain washers 5 adjusting handle of the frame of the grinding parts wing nuts M8 protecting plastic set fixing screw of the protecting cover of the slicing knife p8x158 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 card A pan head screws with cross recessed
5. 210 food stopping board of model 250A 2 board base of model 250A 2 cover of the branch base of model 250A 2 card of model 250A 2 frame of the grinding parts of model 250A 2 main axle of the slicing knife L 209 belt pulley of razor blade of model 250A 2 86 belt pulley of the blade motor 924 cross recessed countersunk head screw M5 x 10 33 O POWER INPUT 1 PROTECTOR MACHINE OF THE MOTOR KI SEMIAUTOMATIC MEAT SLICERS CIRCUIT DIAGRAM IN PUT SW2 protecting switch of the frame of the grinding parts SW3 protecting switch of the protecting cover of the slicing knife sw4 Electrical engineering hot protection machine AN1 start button AN2 stop button M motor C1 starting electric capacitor low voltage controlling circuit diagram of semiautomatic meat slicers 34 B POWER INPUT FULLY AUTOMATIC MEAT SLICERS CIRCUIT DIAGRAM 35 START BUTTON OF THE BLADE MOTOR BUTTON OF THE BLADE MOTOR START BUTTON OF THE SLICE MOTOR TOP BUTTON OF THE SLICE MOTOR DETECTOR MK3P 1 DETECTOR MK3P 1 MOTOR OF THE BLADE MOTOR CAPACITOR MAIN MOTOR OF THE SLICE MOTOR CAPACITOR HOT PROTECTOR MACHINE OF THE MOTOR HOT PROTECTOR MACHINE OF THE MOTOR Postscript WED B200B 1 fittings list Component set of the protecting cover of Handle 430x100 1 the food carrier 1 Component set of the The
6. bring up the emery wheel cover the electric circuit system cuts off the power supply automatically at this time cutting into slices the machine to stop move to turn When let go of the emery wheel cover fix good re pressing to start the switch cutting into slices the luck to turn 7 Clean and Maintain Every time when you have finished using the meat slicer you must clean it up a Before you clean the meat slicer you must cut off the electric power first 6 preventing to start the machine carelessly and cause hurts by the running slicing knife b Turn the thickness adjusting button back to 0 scale c Do not use water to wash this product directly do not use scour that be with high degree of acidity or alkalescency to clean the product and do not use abrasive articles to wipe the surface of the product and the slicing knife Please use a piece of wet cloth with scour to wipe the surface of the product and then use a piece of dry cloth to wipe it up In order to make sure the food is safe and healthy you should clean the meat slicer before you use it each time d Take off protecting cover of the slicing knife clean the cover of the slicing knife and the slicing knife with a piece of cloth and wipe them up To prevent the slicing knife not to rust and keep the food safe and healthy please make sure that the slicing knife is wiped up with dry cloth e when cleaning the slicing knife please specially pay attention to th
7. hand handle food carrier and blocks plank frame 65x5 1 ee WED B250B 1 fittings list WED B300B 1 fittings list protecting cover of the Component set of the Component set of the protecting cover of the food carrier food carrier Handle 930510 Br Handle 930510 WED B250B 2 fittings list WED B300B 2 fittings list 250 food pressing 300 food pressing board a a Guiding stick the Guiding stick of the food pressing board food pressing board 2 14x310 2 14x359 Inner hexagonal Inner Hexangular screw Handle 630x100 Inner Hexangular Inner Hexangular dE 36 zu WED B200B 2 fittings list WED B250B 3 fittings list Name spec quantity Name spec quantity Component set of the Component set of the protecting cover of protecting cover of 1 the food carrier the food carrier Component set of the Component set of the food carrier and frame food carrier and frame Handle 430x100 T Component set of the Component set of the protecting cover of protecting cover of the food carrier 758 WED B250A 1 fittings list WED B300A 1 fittings list m the food carrier 37 WED B200B 1 WED B250B3 I installs the module diagram Hexangular The hand handle aluminum stick blocks the plank Load the dish protects the cover _
8. 128 whole of model 200 food stopping board of model 200 adjusting branch base cover of the branch base food carrier 195x192 small frame A small frame B guiding stick of food pressing board 910x180 O shape rubber band M10 A protecting cover of the food carrier slotted countersund head screw M6 X 15 food pressing board of model 200 copper set 1015 handle of the food pressing board hexagon socket set screws with cup point M4x6 center deviating axle of bearing M8x24 hexagonal screw M6x30 frame of model 200 handle of the frame hexagon socket set screws withflatpoint 10 35 sliding part 931x105 bearing 625Z supporting square axle L 284 ball bearing 6000Z axle of bearing 10 guiding axle of the sliding part 914x333 spring inner diameter 914 5 hexagon socket set screws with cup point M5x8 129 130 131 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 Components list copper set 1412 hexagon socket cap screws M6x25 O shaperubberbandM14 D axle of the sliding part 12x90 copper set 1215 adjusting sliding board nut M10 adjusting screw of the protruding wheel hexagon socket cap screws M6x20 axle set of the adjusting button A protruding wheel A copper pan head screws with cross recessed M6x20 wave shape elastic cushion 910 adjusting button A protecting cover of the slicing knife 9178 5 slicing knife 9220
9. 408 409 410 411 412 413 414 415 416 appropriative screw M8 Components list guiding stick of the food pressing board 914x428 slicing knife 9300 4 main axle of the slicing knife 300A belt pulley of razor blade of model 300A poly V belt 440 fixing screw of the protecting cover of the slicing knife p8x205 card C connecting cushion of the motor motor 270W poly V belt 420 base board 477x377 automatic body 400x320 base 395x183 reducer WPO40 driven pulley 85 20 center deviating wheel bearing S110T K swing bar L 280 oscillating bearing GE8C copper set of the transmission stick round washers for friction grip bolts 010 appropriative screw M10 appropriative screw M8 base of the transmission stick driving pulley of the slice motor motor 300W hexagon screw M10x35 32 hexagon socket cap screws M8x35 classical V belt A650 electric capacitor 10uF pan head screws with cross recessed M6x20 joint of the plastic nut oil pipe p joint of the copper nut O shape rubber band M16 A oil lens three way valve vent valve right angel connector spring outer diameter p6X0 8X30 small metal ball S 6 3 appropriative screw M10x1x14 copper nut M10x1x10 copper nut 10 1 5 hexagon socket set screws with dog point M6x20 hexagon socket set screws with dog point M6x20 small skateboard of transmission stick spring outer diameter 14 5 1 2 28 round washers for friction grip bolts
10. Meat Slicer Series Users Manual Honorific customer Please cautiously read usage manual before use my plant product Moreover and specially notice The first In the manual of whet knife and regulation particularly notice the method that the front whets knife Wanting to slightly press to fix the knife emery wheel hand handle about a second can immediately the most long can t over 2 seconds the hair of razor blade stabs to throw away then otherwise the razor blade will change bluntness Beat a t Fix the knife emerv wheel hand handle The second This machine uses a front to speciallv request Such as because the temperature is too low and put a pole to encourage bore to add not enter oil please with the oil gun aim at a route of travel slipperv piece stalk p 20 position B two with put a pole copper a set of the position add an engine oil and wait until to circulate invite half an hour behind aim at to put a pole to encourage bore to encourage with the oil gun Use a times four hour each time to add engine oil thank a cooperation guiding axle of the copper set of the sliding part 920 transmission stick ID position A This users manual provides this product s detailed information of how to use install maintain and repair it for customers ensuring that this product can be used in the best and most effective way Please keep users manual well and
11. e conne teatri inicie croata 43 BE 1 Main Models and Their Technology Parameter ModelNo characters Cut off product size journey net gross weight weight 14 5kg 16 5kg 465 355 425 140 WED B20 semiauto 410x400x350 0B 1 matic mm semiauto matic semiauto matic semiauto 2 WED B matic semiauto 185 ON matic mm 0 matic mm 0 mm mm m 50Hz mm SER matic mm 50Hz mm IAE 0BI I matic mm mm OB matic 1 automatic Note 1 Cut off journey when cutting the meat the food carrier will move left and right Cut off journey is the farthest direction the foot carrier moves 2 The carton size behind marks in the form is a plywood size 2 Packing List Model No L 3 Commis 2 component Mensis _ Componms is Mess component W Framework Diagram for the Product G H I J F E D C B A A base of the meat slicer B Frame of the foot carrier C handle of the slicing knife D thickness adjusting button E food stopping board F food carrier G food pressing board A H protecting cover of the foot carrier I slicing knife J protecting cover of the slicing knife protect
12. e followings D Put on safety gloves 2 Do not touch the edge of the slicing knife directly Strictly prohibit to clean the slicing knife before cutting off the electric power f When finished cleaning start the machine and let it run for 3 minutes cutting nothing make sure that it could work normally To make sure this product could work long enough you must maintain it termly a The rotary and slip parts should be kept lubricative and agile Please check and add lubricant to the parts termly make sure they could work normally long enough maintain the slicing knife The slicing knife is made of high intensity steels it should not be impinged by hard articles When finished using the product please wipe the slicing knife up with a piece of dry cloth Use a piece of dry cloth with edible oil to wipe the edge of the slicing knife OF for one time each day This is to prevent the slicing knife not to rust 7 The lubricating to the slip axle of the food pressing board se a piece of cloth to wipe the slip axle up 88 Add some edible oil to the slip axle move the food pressing board up and down to help the inleakage of the edible oil till the food pressing board can be moved agilely Do this for one time each day before using the product The lubricating to sliding part axle of the food carrier Add lubricating oil SAE140 lubricating oil onto the sliding part axle move the food carrier r
13. e knife emery wheel hand handle Adjust to return to beginning to start after whetting Revolving the emery wheel covers 180 9 Fix the hand handle Press to fix whole emery wheel hand handle Diagram 1 Diagram 2 Diagram 3 Diagram 4 k The grinding wheel would be dusty and smeary when it has been used for several time please use detergent and brush to wipe them off so that next time you can use it again clean product again 9 Notice and Safety Rules If this product was broken or it caused an accident by being used incorrectly the manufacturer will not take any responsibilities please do not uninstall or change any important parts of this product such as the axle of the slicing knife and the electrical parts Prohibit using this product to cut food that was frozen or with bones Prohibit using this product to cut fish or any other articles that do not belong to food kind X Check the wire and the plug termly make sure they are in good condition and safe enough Obey electricity using rules Prohibit using this product when the insulation parts were broken X Make sure the grounding wire of the product is connected well Prohibit using this product when you are unshod or your hands are wet X When cleaning the product please do not wash it by water directly do not dip the product in water X When using the meat slicer you must make sure that the protecting covers are installed well Prohibi
14. he grinding wheel D clean the grinding wheel and dry it A wipe up the impurities use little edible oil to clean it B tighten the screws of the slicing knife C change the slicing knife 11 The food stopping board touches the slicing knife or it becomes loose The food carrier touches the slicing knife protecting cover Meat sheets are not symmetrical winding or the product cannot slice meat and other foods sliding part moves torpidly D the locking ring of the strap wheel has become loose or has been damaged A the distance between the food stopping board and the slicing knife is not correct D tighten the locking ring or change the strap wheel A adjust the distance to 0 4 0 5mm tighten the screws B the screws on the base of the food stopping board or screws on the adjusting button become loose B tighten the screws C the adjusting copper set may be loose or lost C uninstall the adjusting button and tighten the adjusting copper set or change the adjusting button A the position fixing bolt or nut of the supporting wheel becomes loose B the fixing screws of the frame and the food carrier become loose A the angle of the slicing knife is not correct B the slicing knife has become blunt C the food stopping board has become loose A the position fixing axle is too tight B there may be some impu
15. ight and left to help the inleakage of the lubricating oil till the food carrier can be moved agilely Do this each time for a week e Fully automatic gearing s maintenance Check termly whether the screws of the gearing have become loose or not whether the lubricating parts have been frayed or burned or not Reinforce the loosed screws and add lubricating oil SAE140 lubricating oil on time It is requested to do this one time each week f Maintain the knife grinding parts 0 Each time before grinding the knife check whether the axle of grinding wheel is retractile or not 2 Each time before grinding the knife check whether the grinding wheel can run agilely or not 8 Each time before and after grinding the knife clean the grinding wheel 8 Grinding the knife and relative things needed to be paid attention to When the slicing knife has become blunt you need to grind the slicing knife following below steps a off the electric power and clean the slicing knife b Check whether the thickness adjusting button has been turned back to the 0 scale Check whether the knife grinding parts can work normally or not For example check whether the handle of the grinding wheel can be moved agilely or not or check whether the grinding wheels are firm enough or not d Unloose the position fixing screw of the grinding wheel lift the grinding wheels to check whether it can move or not and then put them down to the c
16. ing ring of the slicing knife L protecting cover of the grinding wheel M handle of the grinding wheel N position fixing screw of the grinding wheel O position fixing screw of the food stopping board P position fixing screw of the protecting cover of the slicing knife Q plastic feet R wire and plug S blade motor switch T food pressing board B U slice motor switch V automatic body 4 Characters of this product 1 this product is with elegant design and reasonable structure It accords with the national sanitation standard 2 It is easy and convenient to use and operate it 3 It is convenient to adjust the thickness of the meat slices The meat slices cut by this product are very nice 4 the structure of this product is concise It is convenient to grind the slicing knife And it is easy to be repaired and maintained 5 The complete function meat slicer has organization from the lock and the safe power failure protect and the safe and low electric voltage protect function 5 Installation and Use 1 Unfold the package and put the meat slicer onto a clean and smooth place Notice The behind of the fuselage should stay to have the 150 cm the above space easy to operation 2 The WED B200B 1 the WED B250B3 I the WED B300B1 I is whole functions slice machine will load dish and support module from the top downwards pack a route of travel slippery piece up then by hand the handle lock tightly fixedly good P
17. lastic feet Nut MIO AI 6 0 Pa screw M10 oil pipe A 2 three way valve FS f tal hexagonal screw M10 While needing to dismantle to unload a stainless steel box operate a step as follows 1 Dismantle oil pipe A The method is compress tightly the blue bonnet of three way valve first then take the oil pipe A to pull out like right diagram 2 Let the meat slicer to lie down loosen the nut M10 then loosen the hexagonal screw blue bonnet of MI 0 three way valve 3 Loosen the four plastic feet the then loosen stainless steel box and base of the meat slicer with each other of four M10 screw the stainless steel box can immediately dismantle Postscript The suppliers themselves undertake the following responsibilities obey the requirements mentioned on the users manual all products with EC symbol should accord with the healthy and safety basic requirements of EC Standard accord with relative regulations Please kindly forgive us that we will not make a notice in addition once we have made some changes to this users manual Product quality guarantee Product Name WED B200 250 300 series meat slicer Customer s Address Customer s Name Purchase Date date month Guarantee Period FROM date month year TO date month year Name and Address of the purchasing Store If there is any quality problem please contact with o
18. make sure that when you need to read it you can find it out soon We may make few adjustments to the real product so that they can work more effectively In that case the real product may differ from the description of the users manual But please note that the users manual is still fit for the real product Contents Main technology parameter and packing list ees 3 Frameworkdiastam ri 4 5 10 Malfunction and 11 12 Components diagram WED B200 Bal cs seston nissen awa elogia e c 13 WED B200B 2 5 ae tn cone tnra ie 14 WED B 2 OB Lara e saneta seas RES SE nea ctr 15 WED B250B 2 ANNA 16 WED B230D Sisi 17 WED BL Alirio 18 19 WEED BZ SO ASD nis ka OE ERE RAS 20 21 WED B25 OBS a0 eT RANA 22 BR300BaR oia 23 300 2 ii 24 WED B300B Liconsa rra ici nie 25 WED B300A nn ii ni i 26 27 Components ERR 28 33 Electrical CCU Mr A AS scene 34 35 RINES Mein 36 37 Install the module 38 39 AAA ewe e d 40 Automatic body oiling schematic diagram 41 Automatic stainless steel body to disassemble of 42 Product guarante
19. op Button of the Automatic Switch first and then press the Stop Button of the Semiautomatic Switch to stop cutting 8 When finished cutting foot please adjust the food stopping board back to the 0 scale and clean the meat slicer 6 the whole function slice model of from the usage that lock and safe power failure function Whole function model 1 The When regulates the knob 0 the want the only a the hand of the loose expenditure handle the and hear the loading dish the go toward the left the side circulate would TA the of a the ring the load the dish support the and can t the move fixedly the at this time the regulate the knob and the can t turn the to move the can bring the up the whole loading dish support upwards at this time When pack up the loading dish support winding up the support hand handle load the dish support and can move at this time When regulate the knob not in 0 even loosenning a hand of expenditure handle also can t bring up the loading dish support 2 When the slice machine at circulate as long as loosen to open the fixed hand handle of protect the knife dish the electric circuit system cuts off the power supply automatically at this time cutting into slices the stop operation of machine When wind up the fixed hand handle of protect the knife dish re pressing to start the switch cutting into slices the luck to turn 3 When loosen to open the emery wheel to fix the hand handle and will
20. orrect position lock the position fixing screw of the grinding wheel again Check whether there are any gaps between the grinding wheels and the slicing 8 knife Diagram 1 Special attention when bring up the emery wheel cover the point of a knife of the razor blade bare please very careful do not touch the point of a knife in order to prevent accidental injury e Connect the meat slicer with the electric power press Start Button to let the slicing knife run push down the handle of the grinding wheel to let it touch the slicing knife to start grinding the knife Keep doing that for 10 15 seconds and then loose the handle of the grinding wheel to stop grinding Diagram 2 f press the Stop Button to let the slicing knife stop running then check whether the edge of the slicing knife is sharp enough or not If not grind it again g press the Start Button to let the slicing knife run push down the handle of the grinding wheel again softly grind the slicing knife for 1 2 seconds to rid of the bur Diagram 3 h when finished press the Stop Button and cut off the electric power i adjust the knife grinding parts back to their original positions and lock the position fixing screw of the grinding wheel Diagram 4 j When grinding the slicing knife please keep your eyes away from the running direction of the grinding wheel preventing to get hurts by the dust and fragment of the grinding wheel Press to whet th
21. orrect positions of the frame and the food carrier tighten the screws B uses the inner hexagonal wrench to correct the position of the fixing plastic nail and tighten the nut C tighten the screws The food stopping board lower than the slicing knife When we start the product the slicing knife runs powerlessly The grinding wheel cannot grind the knife the or grinding wheel is broken A the fixing screws on the supporting base of the food stopping board become loose B the thickness adjusting button and the adjusting axle become loose A adjust the food stopping board make it balance with the slicing knife tighten the screws B change the thickness adjusting button adjust it again A the strap becomes loose A tighten the strap and the screws B the strap is greasy and it causes the strap skidding A use it incorrectly B the angle of the grinding frame is not correct C the grinding wheel protecting cover touches the grinding wheel D there is water or oil on the grinding wheel The slicing knife jumps fiercely A there may be some impurities on the surface of the strap wheel B the screws of the slicing knife may not be tightened enough C the slicing knife is deformed B clean the strap or add some dry powder onto the strap A please read the users manual for details B adjust the base of the grinding wheel C adjust the base of t
22. rew of the protecting cover of 329 the slicing knife p8x178 332 card B 333 281 connecting cushion of the motor 339 motor 240W 340 poly V belt 370 343 288 relays MK3P I 344 289 electric capacitor 7uF base board 397x317 345 294 nut M8 346 slotted countersund head screws 8 25 347 296 spring washers 98 whole frame of model 300 348 302 food stopping board of model 300 349 303 guiding stick of the food pressing board 353 914x265 food pressing stick of model 300 31 Components list food carrier 300x280 small frame A small frame B guiding stick of the food pressing board 914x358 small frame A small frame B food pressing board of model 300 A small frame of model 300 frame of model 300 sliding part cast iron food pressing board of model 300B supporting square axle L 430 guiding axle of the sliding part 920x470 steel set p26x25 adjusting sliding part of model 300B adjusting sliding part of model 300A axle set of the adjusting button C raised wheel C adjusting button C protecting cover of the slicing knife 9248 5 slicing knife 9300 3 cross recessed countersunk head screw M6x16 protecting ring of the slicing knife 9317 4 main axle of the slicing knife L 204 belt pulley of razor blade of model 977 frame of the grinding parts of model 300 food carrier 300x350 358 359 360 361 362 376 377 381 382 383 392 401 402 403 404 405 406 407
23. rities at the supporting axle and the square axle of the sliding part C the copper set was damaged or was not in its right position 12 A same as 1 B same as 1 A adjust the angle of the knife again B grind the slicing knife again read the users manual for details C uninstall the adjusting button and tighten the adjusting copper set or change the adjusting button A adjust the screw of the position fixing axle to the 0 scale and let it touch the square axle surface tighten the nut B wipe up the supporting axle and the square axle of the sliding part and add some butter C change the copper set 13 891 191 OSI 281 991 L 80S28 Q3A POW LO N m LLI 5 gt g0scg GAM w 072 17 Mod WED B250A 1 l Vosza CAM POW 19 Mod WED B250A 2 20 09 9 0 POW 21 1 875 675 OST IST ZST 1 800 8 CaM pow a 691 800 8 Q3M pon 691 24 I Ldooea CaM PON 25 098 196 OST IGI 881 186 L VOO 8 CAM POW 26 lt RE e O LU gt 27 121 122 123 124 125 126 127
24. rotect loading dish a cover after tightly solid go to loading dish up attach assemble diagram 3 Connect this product with correct voltage electric power as the user s manual required Make sure the grounding is well enough 4 Start the machine at this time the indicator is bright for the normal start let the slicing knife run for 1 2 minutes cutting nothing make sure that the slicing knife could work normally The slicing knife should run counter clockwise 5 Will block the plank fixed position hand handle to adjust to leave to block the plank hereafter first then regulate the thickness to regulate the knob the slice thickness that choice need will block the plank fixed position hand handle to adjust and block the plank contact again the lock is tightly the form butterfly shape nut M8 6 Put the meat or other food onto the food carrier at the degree about 5 C and then use the movable food pressing board to press the food and push the food towards the food stopping board 7 If it is a semiautomatic meat slicer press the Semiautomatic Switch to start 5 machine first and then hold handle of the slicing knife to let the foot carrier move left and right to start cutting Press the Stop Button to end the cutting If it is a fully automatic meat slicer press the Semiautomatic Switch at the above first then press the Automatic Switch at the below to start cutting If you want to stop cutting please press the St
25. sting sliding part axle of the sliding part 914x146 copper set 1412 adjusting sliding board 30 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 small frame A small frame B guiding stick of the food pressing board 914x308 axle set of the adjusting button B raised wheel B copper pan head screws with cross recessed M6x25 ve shape elastic cushion 912 justing button B protecting cover of the slicing knife 9208 5 slicing knife 9250 position fixing wheel protecting ring of the slicing knifep266 4 main axle of the slicing knife L 178 belt pulley of razor blade 965 capnut MIO flat cushion 910 food stopping board of model 250 B base of the food stopping board of model 250 B pan head screws with cross recessed M5x30 nut M8 sliding part 940x130 food carrier 230x300 guiding stick of the food pressing board 914x378 center deviating axle of bearing M8x30 nut M4 plain washers 04 305 262 frame of the grinding parts of model 306 250 307 stainless steel handle 308 the left steel slice of the handle 265 the right steel slice of the handle 309 pan head screws with cross recessed 310 M6x15 312 pan head screws with cross recessed 316 8 10 318 Spring 17 2 350 321 269 Red ball head hand handle 5030 322 270 belt pulley of razor blade of model 323 250A 1 965 326 276 fixing sc
26. t touching the slicing knife and other moving parts Prohibit standing at the direction that the slicing knife is running toward The slicing knife may not run because knife supporting was locked or there was something wrong with this product In that case please cut off the electric power first and then repair and maintain it X If the food carrier or the food pressing board work hindered please clean the slip axle and add some 307 lubricating oil or edible oil onto it When the strap works not so good please check whether the screws at the button of the base are tight enough or not or check whether the strap is too loose or not If so please tighten the screws or adjust the degree of tightness of the strap If the meat slicer will not be used for a long time please cut off the electric power Please pay attention to keeping the product away from water and dampness When the point of a knife of the razor blade with protect the cleft of the knife wreath big in 5 mms needing to replace the new razor blade 10 8 Malfunction and maintenance malfunction Food carrier Shakes Possible malfunctions and maintenance methods malfunction analysis Maintenance methods the fixing screws of the frame and the food carrier become loose B fixing plastic nail ofthe sliding part do not at the 0 scale C the fixing screws of the square axle and the round axle become loose c
27. ur agents or with the suppliers directly Please note that this product has past strict quality testing and controlling system It is a qualified product During Guarantee Period under the conditions of using this product normally and correctly if there is something wrong with the product the manufacturer agree to help repairing the product for free as the following contents state a When you need to repair the product please contact with the purchasing Store and show the Product Quality Guarantee to the store The Product Quality Guarantee is not valid if it hasn t any records or signatures In that case we will not agree to help repairing the product for free b During the Guarantee Period we charge for cost only when changing the damageable parts c We do not agree to repair the damageable parts such as the slicing knife and the grinding wheel for free d Even during the Guarantee Period we do not agree to repair the damaged product freely if its damages were caused by incorrect using unstable voltage or irresistible disaster 43
Download Pdf Manuals
Related Search