MS-(H)-Pro Digital（Hotplate）Magnetic Stirrer
Contents
1. heating is switched ON or OFF via push the knob MS H Pro Mode Key Shift among the three operating modes A B and C mode Set Key Set Setting all parameters of the device e LCD displays the real working state and LCD all settings LED Heat PORNE When the heating function is switched MS H Pro P ON the LED Heat is lit When the stirring function is switched LED Stir a ON the LED Stir is lit Power Switch Switch ON or OFF the instrument Table 2 5 2 Display Characters Temp and C Stir Mode Set Hot Probe Remote Err Rated value Real value Real value Temperature Stir Set Error Rated value Remote Probe Remote External HotPlatewar control probe ning Mods Figure 4 Descriptions Display temperature when the heating function is switched ON Display stirring state when the stirring function is switched ON Display the setting mode in order of A B and C after pressing mode key Press setting key to set function and display Set characters Display hot warning if the heating plate temperature 1s above 50 C after switching OFF the heating function Display when using external probe Display in case of remote control Display in case of error happening Display value in case of heating or stirring function switching ON Table 3 MS H Pro Digital Hotplate Magnetic Stirrer Note If both heating and stirring functions have been started at the same time the2. Table 6 Note The software StirPC can be download free on our website www scilogex com MS H Pro Digital Hotplate Magnetic Stirrer 16 Main spare parts 16 2 List of spare parts 16 1 Spare parts diagram No Name l Workplate 11 Driver circuit board Hole for external 18 19 20 1 2 Direct current Motor 9 12 temperature without brush sensor holder 15 LE oS Tumani LTE Internal temperature j Bi i Housing 14 LU sensors 11 NI 5 Ventilation Permanent magnet o oy 6 Control Heating parts External A A 7 temperature 17 Protective plate sensors socket socket Figure 8 Mine 10 cues 20 Interface circuit board board LO SCILOGEX LLC 500 Four Rod Road Suite 122 Berlin CT 06037 USA Tel 1 860 828 5614 Fax 1 860 828 5389 E mail info scilogex com Website Http www scilogex com
3. dry clean room and temperature stable environment MS H Pro Digital Hotplate Magnetic Stirrer 13 Associated standards and regulations Construction in accordance with the following safety standards EN 61010 1 UL 3101 1 CAN CSA C22 2 1010 1 EN 61010 2 10 Construction in accordance with the following EMC standards EN 61326 1 Associated EU guidelines EMC guidlines 89 336 EWG Instrument guidelines 73 023 EWG 14 Technical data Voltage VAC 200 240 100 120 Frequency Hz 50 60 MS H P Paver ait S ro SO MS Stirring point position quantity Max stirring quantity H20 L Max magnetic bar mm Motor type Max power input of motor W Max power output of motor W Speed range rpm Rotary speed display Speed display accuracy rpm Hotplate material of the hotplate mm Heating power W Heating rate 1L water K min Temperature range C Temperature display C Temperature display accuracy C Control accuracy of heating temperature C l 20 80 External rotor brushless motor 18 10 100 1500 LCD l Stamless steel porcelam enamel 135 500 MS H Pro 6 MS H Pro RT 340 MS H Pro LCD MS H Pro 0 1 MS H Pro 1 MS H Pro The safety temper of the hotplate C ature range 100 350 MS H Pro Temperature sensor in medium PT1000 MS H Pro Control accuracy of heating temperature with temperature sensor C Dimensions mm
4. electrical properties of the interface lines and for the allotment of the signal status standard RS232 C corresponding with DIN66259 Part 1 applies e Transmission method Asynchronous signal transmission in start stop operation e Mode of transmission Fully Duplex e I start bit 7 character bits 1 parity bit straight even I stop bit e Transmission speed 9600 bit s NOTE Forbid to plug in or plug out the RS 232C communication line 11 Faults Instruments can tbe power ON Check whether the power cable is plugged Check whether the fuse is broken or loose e Fault in power on self test Switch OFF the unit then switch ON and reset the instruments to factory default setting e Temperature cannot reach set point Check whether the safety temperature value is set too low e Stir speed cannot reach set point Check whether the stirring bar breakaway monitoring is ON Excessive medium viscosity may cause abnormal speed reduction of the motor e Heating cannot be started when push the temperature control knob or stirring cannot be started when push the speed control knob Check whether the unit is in the mode setting program Exit from the mode setting and restart the heating stirring functions e Unit cannot be powered off when switched off Check if the residual heat warning function is still ON and hotplate temperature is above 50 C the LCD still work and Hot flash Turn off resi
5. the function setting key till the LCD displays SAFE e Adjust the temperature setting key to set the safety temperature from 100 to 350 C e Press continuously the function setting key till Set disappear e The value of the safety temperature has been stored and setting is completed 9 Function Stirring 9 1 Basic Stirring The function stirring is switched on or off via the rotary stirring knob The motor speed is set on the knob 100 to 1500 rpm in steps of 10 rpm When both the function heating and stirring are switched on and those above operations are done the LCD will shift to the speed value and come back to the temperature value in about 5 seconds 9 2 Stirring bar breakaway monitoring In the A or B mode the stirring bar breakaway monitoring can be set as follows e Press continuously the function setting key till the LCD displays br e Press the function setting key to switch on or off the stirring bar breakaway monitoring function and the LCD displays On or OFF e Press continuously the function setting key till disappear e The stirring bar breakaway monitoring function has been 14 Set 11 MS H Pro Digital Hotplate Magnetic Stirrer set Breakaway can occur when stirring at high speeds when large stirring bars are being driven at speeds close to the maximum magnetically torque or sample viscosity changes Using MS H Pro stirring bar breakaway monito
6. 48 18900049 18900006 18900007 18900008 MS Pro Digital Magnetic Stirrer Stainless Steel Cn plug 220V 50Hz 60Hz MS Pro Digital Magnetic Stirrer Stainless Steel USA plug 110V 50Hz 60Hz MS Pro Digital Magnetic Stirrer Stainless Steel Euro plug 220V 50Hz 60Hz MS Pro Digital Magnetic Stirrer Stainless Steel UK plug 220V 50Hz 60Hz MS Pro Digital Magnetic Stirrer Stainless Steel USA plug 220V 50Hz 60Hz MS 135 1 Carrier plate Used with MS135 2 5 MS 135 2 Quarter 4 ml reaction vessel MS 135 3 Quarter 20 ml reaction vessel MS 135 4 Quarter 30 ml reaction vessel MS 135 5 Quarter 40 ml reaction vessel MS 135 6 Quarter 8ml reaction vessel MS 135 7 Quarter 16 ml reaction vessel Stirring bars 10mmx6mm Ipcs pk Stirring bars 15mm x 8mm Ipcs pk Stirring bars 20mm x 8mm Ipcs pk 18900009 12500005 18900011 12500004 18900013 18900014 18900015 18900016 18900017 18900018 18900019 18100319 Stirring bars 25mm x 8mm Ipcs pk Stirring bars 30mm x 6mm Ipcs pk 50mm x 8mm Ipcs pk Stirring bars 40mm x 8mm Ipcs pk Stirring bars Stirring bars 65mm x 8mm Ipcs pk Stirring bars 80mm x 13mm Ipces pk Stirring bar mover Ipc PT1000 Tempersture probe for MS H pro Stander kit of PT 1000 F100 unit cover for none heat plate model MS Pro MS S F101 unit cover for heat plate model MS H Pro MS H S 9 Pin interface line suitable for StirPC software
7. MS H Pro Digital Hotplate Magnetic Stirrer Cat No 12300137 User Manual MS H Pro Digital Hotplate Magnetic Stirrer MS Pro Digital Magnetic Stirrer Please read the User Manual and the related Video of this instrument on our website carefully before use and follow all operating and safety instructions The website www scilogex com SCILOGEX Contents Ce TRTRTTTFTTrT lno ke secre crete esis ces senses ces coeds eee ee eee ots E A T MN IIA PTT Safety Instructions TTTR7R uuq 2 PROPEL USE sasa nna knne E a TO 3 1 Receiving Inspection la 3 2 Listing of Items TRRRTrFFF T T R TRF R F T TU PT 4 Trial run sssssssarsscnncshiseoasconnse lawanteatelacwa sacs ianvesamebenvansaviiieleiwoasmussaneties 5 5 Control and Display Saeed eee scons Dad ent eee 6 Cohirol PM EO ES 32 Display STTTTTTTTTTTTTTTTTTTETTTTTTTTTEET O Blkavo 3 VARTO AEETI TTTT TTRTTFTrTTTTTT 6 1 Initializing Sequence eieiei 6 2 Default Settings 6 3 Resetting Parameters to Factory Settings J Operating Modere es usu aron 7 1 Operation Mode of MS H Pro 7 2 Operation Mode of MS Pro 8 Function Heating MS H Pro 8 1 Working with External Temperature Sensor 8 2 Residual Heat Warning HOT 10 8 3 Setting the Safety Temperature i 10 uncon Sit te M MMM RTTZIEFTRO 11 9 1 Basic Stir
8. Weight kg 0 2 MS H Pro 280 x 160 x 85 26 Permitted ambient temperature C Permitted relative 5 40 humidity 80 Protection class acc to DIN 60529 IP42 RS232 interface 15 Products Cat No 811123019999 Yes Table 6 and Accessories Description MS H Pro Digital Hotplate Magnetic Stirrer Porcelain enamel Cn plug 220V 50Hz 60Hz 811123029999 811123039999 811123049999 811123059999 811123069999 811123109999 811123119999 811123149999 MS H Pro Digital Hotplate Magnetic Stirrer MS H Pro Digital Hotplate Magnetic Stirrer Porcelain enamel USA plug 110V 50Hz 60Hz MS H Pro Digital Hotplate Magnetic Stirrer Stainless Steel Cn plug 220 50Hz 60Hz MS H Pro Digital Hotplate Magnetic Stirrer Stainless Steel USA plug 110V 50Hz 60Hz MS H Pro Digital Hotplate Magnetic Stirrer Porcelain enamel Euro plug 220 50Hz 60Hz MS H Pro Digital Hotplate Magnetic Stirrer Porcelain enamel UK plug 220V 50Hz 60Hz MS H Pro Digital Hotplate Magnetic Stirrer Stainless Steel Euro plug 220V 50Hz 60Hz MS H Pro Digital Hotplate Magnetic Stirrer Stainless Steel UK plug 220V 50Hz 60Hz MS H Pro Digital Hotplate Magnetic Stirrer Porcelain enamel USA plug 220V 50Hz 60Hz MS H Pro Digital Hotplate Magnetic Stirrer 811113019999 811113029999 811113039999 811113049999 811113089999 Accessories 18900001 18900002 18900003 18900004 18900005 189000
9. at control knob in advance before change mode 8 Function Heating MS H Pro The device is controlled by Digital Temperature Control Technology which has two separate safe circuit The hotplate is kept at a constant temperature by a digital control circuit The hotplate temperature can also be monitored from a separate adjustable safety circuit The two temperature sensors Pt1000 internal for temperature control are built into the hotplate The single external Pt1000 can monitor the temperature of sample If external temperature sensors needed it must be plugged in MS H Pro Digital Hotplate Magnetic Stirrer before the device 1s switched ON e Ensure the external temperature sensors connecting firmly before heating e Set the temperature via turnning the temperature control knob slowly to the ideal scale e When the heating function is switched on the LED Heat will light up and the LCD will display the real temperature e The rated temperature will be displayed on the right hand side of the LCD as well as Temp and C characters e The heating function is switched on or off via pushing the heat knob 8 1 Working with external temperature sensor Figure 5 MS H Pro Digital Hotplate Magnetic Stirrer In the B mode if the external temperature sensor is not plugged in Probe will flash If plugged in Probe will be shown on the digital display to indicate that the senso
10. display of function heating always has higher priority If in this case speed is changed via the stirring knob it display stirring speed and reverses to temperature in the duration of 5 seconds 6 Initialization 6 1 Initializing sequence e Turn on instrument by the power switch e The Heat and Stir LEDs and the LCD display flash about 3 times e LCD displays the workplate s safe temperature limit in SAFE xxx C e LCD displays residual heat warning rES On OFF e LCD displays stirring bar breakaway monitoring br On OFF e LCD displays operating modes A B e LCD displays the Probe characters in case of connecting with external temperature sensors 6 2 Default settings MS H Pro is supplied with the following default settings MS H Pro Digital Hotplate Magnetic Stirrer Items Default settings Operating mode A Setting temperature C 25 SAFE 350 Setting rotary speed rpm 100 Residual heat warning On Stirring bar breakaway monitoring OFF Table 4 6 3 Resetting parameters to factory settings Reset the parameters to the default settings as follows e Turn off by the power switch O T to O e Have the keys Set and Mode pressed down at the same time and switch on the main O I switch Release buttons after 5 seconds e The unit is now set to the factory default settings 7 Operating modes 7 1 Operation modes of MS H Pro Operatio
11. dual heat warning function before powered OFF the unit Lf these faults are not resolved plesse set the instruments to factory default setting or take the unit to your technical Service center 12 Maintenance and Cleaning e Proper maintenance can keep instruments working in a good state and lengthen its lifetime e Be careful not spray the cleanser into the instrument when cleaning e Unplug the power line when cleaning e Only use cleanser that we advised as below 13 MS H Pro Digital Hotplate Magnetic Stirrer Dyes Isopropyl alcohol Water containing tenside Construction materials l isopropyl alcohol Water containing tenside Cosmetics l isopropyl alcohol Foodstuffs Water containing tenside Fuels Water containing tenside Table 5 e Wear the proper protective gloves during cleaning of the instrument e Before using other method for cleaning or decontamination the user must contact the manufacturer ascertain that this method does not destroy the instrument e The enamel makes the hotplate easier to care for and more resistant to acids and bases Because of it however the heating plate is also more susceptible to extreme fluctuations in temperature and the force of impact This can result in cracks forming or the coating flaking off e The instrument must be cleaned and put it into the initial packaging carton before sending to service for repair avoiding the contamination of hazardous e Use the instrument in a
12. is inserted in the media to a depth of at least 20 mm e When using metal vessels do not place the temperature sensors on the bottom of the vessel Placing sensors on the vessel bottom can cause excessively high temperatures to be measured especially in media which have poor conductivity The tip of the measuring sensor must be at least 5 mm from the vessel bottom a distance of 10 mm is ideal e The instrument can only be disconnected from the main power supply by pulling out the mains plug or the connector plug e The voltage stated on the label must correspond to the maln power supply e Ensure that the mains power supply cable does not touch the heating base plate Do not cover the device e The instrument may only be opened by experts e Keep away from high magnetic field e Observe the minimum distances between the devices between the device and the wall and above the assembly min 100 mm gt 100mm Figure 1 2 Proper use The instrument is designed for mixing and or heating liquids in schools laboratories or factories This device is not suitable for using in residential areas or other constraints mentioned in Chapter 1 3 Inspection 3 1 Receiving Inspection Unpack the equipment carefully and check for any damages which may have arisen during transport If it happens please contact manufacturer for technical support Note If there is any apparent damage to the system please do not plug it into the
13. lip dry and fireproof surface do not operate the instrument in explosive atmospheres with hazardous substances or under water e Gradually increase the speed reduce the speed if The stirring bar breakaway because of too high speed The instrument is not running smoothly or container moves on the base plate e Temperature must always be set to at least 25 C lower than the fire point of the media used e Beware of hazards due to Flammable materials or media with a low boiling temperature Overfilling of media Unsafe container e Process pathogenic materials only in closed vessels e If the case of the stirrer bar is PTFE please note elemental fluorine three fluoride and alkali metals will corrode the PTFE and Halogen alkanes make it expansion at room temperature Molten alkali alkaline earth metals or their solution as well as the powder in second and third ethnic of the Periodic Table of Elements will have chemical reaction with PTFE when temperature reaches 300 400 C e Check the instrument and accessories before hand for damage each time you use them Do not use damaged MS H Pro Digital Hotplate Magnetic Stirrer components Safe operation is only guaranteed with the accessories described in the Accessories chapter Accessories must be securely attached to the device and cannot come off by themselves Always disconnect the plug before fitting accessories e Ensure that the external temperature sensor
14. n mode A e MS H Pro has heating and stirring functions e Users can control on the front panel or by remote PC e Residual temperature warning safe temperature limit and stirring bar breakaway monitoring can be set in this mode Operation mode B e MS H Pro has heating and stirring functions e Users can control on the front panel or by remote PC e Residual temperature warning safe temperature limit and stirring bar breakaway monitoring can be set in this mode Operation mode C e MS H Pro maintains the state of the heating and stirring functions before the last switching off mains OFF as well as the data set last can be changed e Remote control can be used without supporting external temperature sensors e Residual temperature warning safe temperature limit and stirring bar breakaway monitoring can t be set in this mode 7 2 Operation modes of MS Pro Operation mode A e MS Pro has heating and stirring functions e Users can control on the front panel or by remote PC e Stirring bar breakaway monitoring can be set in this mode Operation mode B e MS Pro maintains the state of the heating and stirring functions before the last switching off mains OFF as well as the data set last can be changed e Remote control can be used e Stirring bar breakaway monitoring can t be set in this mode Note Mode changing and parameter setting is forbidden when the instrument is running Switch OFF Stir and He
15. power line 3 2 Listing of Items The packing includes the following items Items Qty Main unit l Power cable 1 Stirrer bar 1 User manual l Table 1 4 Trial run e Make sure the required operating voltage and power supply voltage match e Ensure the socket must be earthed reliably MS H Pro Digital Hotplate Magnetic Stirrer e Ensure the power be off e Plug in the power cable ensure the power be on and begin initializing e Add the medium into the vessel with a stirring bar e Put the vessel on the workplate e Set the rated stirring speed and start stirring e Observe the stirring bar and LCD display e Set the rated temperature and start heating e Observe the real temperature on LCD display e Stop the heating and stirring functions If these operations above are normal the device is ready to operate If these operations are not normal the device may be damaged during transportation please contact manufacturer for technical support MS H Pro Digital Hotplate Magnetic Stirrer 5 Control and Display 5 1 Control elements LED Heat MS H Pro Mode Key Function Key LCD LED Stir Temperature control knob MS H Pro Speed control knob Power Switch Figure 3 Items Descriptions Set the rated rotary speed The function Stirring is switched ON or OFF via push the knob Speed control knod Temperature control Set the rated temperature The function knob 9
16. r is operating The external temperature sensors value and actual temperature are displayed Compared with the temperature control of the hotplate the external temperature sensor can control the medium s temperature more precisely Warning Forbid to Plug in pull out external temperature sensor in heating 8 2 Residual heat warning HOT In the A or B mode users can set the residual heat warning function as follows e Press continuously the function setting key till the LCD displays rES Press the temperature regulation key to switch on or off the residual heat warning function and the LCD displays On OFF e Press continuously the function setting key till disappear e The residual heat warning function has been switched on 66 Set or off In order to prevent the risk of burns from a hotplate MS H Pro has a residual heat warning function When the heating function is switched off and the hotplate temperature is still above 50 C Hot will flash to warn that there is a hazard of burns from the hotplate When the heating plate temperature drops to below 50 C the unit will automatically switch off If users want to turn off the LCD immediately just pull out the plug directly When the plug is pulled out the residual heat warning function can not be run 8 3 Setting the safety temperature In the A or B mode the safety temperature can be set as follows e Press continuously
17. ring 11 9 2 Stirring Bar Breakaway Monitoring 11 U Weert ios ss o A 12 11 Faults TTTTRrR FTTUy PTRETTTRTREFFTETRE 12 12 Maintenance and Cleaning qyq qZu7 y9qEEEE 13 13 Associated Standards and Regulations 14 14 Technical Data squuuspusuos euska bank 14 15 Products andAccessories eee 15 16 Main S paro PANIS mi megi Inside back 16 1 Spare Parts Diagram of MS H Pro Inside back 16 2 List of Spare Parts of MS H Pro Inside back MS H Pro Digital Hotplate Magnetic Stirrer Preface Welcome to the MS H Pro Digital Hotplate Magnetic Stirrer User Manual Users should read this Manual carefully follow the instructions and procedures and beware of all the cautions when using this instrument Service When help needed you can always contact the Sevice Department of manufacturer for technical support in the following ways SCILOGEX LLC 500 Four Rod Road Suite 122 Berlin CT 06037 USA Tel 1 860 828 5614 Fax 1 860 828 5389 E mail info scilogex com Website Http www scilogex com Please provide the customer care representative with the following information e Serial Number on the rear panel e Description of problem 1 e hardware or software e Methods and procedures adopted to resolve the problems e Your contact information Warranty You have purchased a Scilogex inst
18. ring function can be set at the rotary speed range between 300 and 1500 rpm When stirring bar breakaway is detected stirring is stopped immediately to enable the stirring bar to be picked up After this stirring starts agaim and rotary speed increases up to the set speed If a further stirring bar breakaway occurs within the next 3 minutes of stirring at a constant set speed the stirring bar will be picked up again and stirring will restart but this time at the set speed reduced by 100 rpm The speed will be reduced each time in 100 rpm steps until the minimum of 200 rpm is reached In this case you should select new test conditions IMPORTANT You must calibrate and test the stirring bar breakaway monitoring function for your particular configuration taking into account the stirring bars speed vessel and medium you are using MS H Pro Digital Hotplate Magnetic Stirrer 10 Remote control Socket Connection PT 1000 RS232C Figure 6 The unit can be controlled from an external PC using the dedicated software via the RS232 C serial interface fitted to the unit Data communication from laboratory instrument to computer is only possible on demand of the computer e The functions of the interface lines between laboratory instrument and automation system are selected from the specified signals of the EIA standard RS232 C corresponding with DIN66020 Part 1 The allotment of the bushing can be taken from illustration e For the
19. rument This instrument is warranted to be free from defects in materials and workmanship under normal use and service for a period of 24 months from the date of invoice The warranty is extended only to the original purchaser It shall not apply to any product or parts which have been damaged on account of improper installation improper connections misuse accident or abnormal conditions of operation For claims under the warranty please contact your local dealer You may also send the instrument direct to our works enclosing the invoice copy and by giving reasons for the claim You would be solely liable for freight costs I Safety Instructions Warning e Ensure that only trained staff work with the Read the operating instructions carefully before use the instrument instrument Forbid to heat the substances with low burning point or easy volatile MS H Pro Risk of burn e Pay attention to the residual heat after Caution when touching the housing parts and the heating plate The heating plate can reach temperatures of 340 CC switching off Protective ground contact e Make sure that socket must be earthed protective ground contact before use e When work wear the personal guard to avoid the risk from Splashing and evaporation of liquids Release of toxic or combustible gases e Set up the instrument in a spacious area on an stable MS H Pro Digital Hotplate Magnetic Stirrer clean non s
Download Pdf Manuals
Related Search