English User Manual
Contents
1. FOR OUTDOOR USE ONLY Read the instructions before using the appliance Warning Accessible parts may be very hot keep young children away ASSEMBLY AND USER INSTRUCTIONS FOR OUTDOOR GAS FIRE PITS USING LIQUEFIED PETROLEUM GAS Your new Cocoon Table SRRSO65xx l2 amp SRRSO40xx l2 is made from the highest quality materials and produced under strict manufacturing controls Please read the Instructions for assembly before commencing and follow the instructions for use carefully We congratulate you on your decision to buy this outdoor gas grill and wish you great fun when warming with it PLEASE READ THESE SAFETY INSTRUCTIONS IN FULL BEFORE COMMENCING ASSEMBLY Important Safety instructions The fire pit is safe and easy to use The following rules must be followed _ AU 01 Ensure that the unit has been assembled correctly according to the instructions Never loosen or allow the gas connection to become loose Should this happen immediately ensure that the gas is turned off and then re check the security of the connection The appliance shall be kept away from flammable materials Read the Users instruction Sections and instructions written on the fire pits refer to them whenever necessary Never leave the fire pit unattended while using Inthe event of a gas leak turn off gas supply at the LPG cylinder or the main shut off valve of city network gas 7 Keep child2. e Immediately call your gas supplier from a neighbors phone Follow the gas supplier s instructions e lf you cannot reach your gas supplier call the fire department LIGHTING INSTRUCTIONS 1 Remove protective storage cover and locate the manual gas control valve and igniter button on the fire pit 2 Make sure fuel supply is properly connected and turned on at the source tank 15 3 Depress igniter button until you hear it sparking You will hear a small popping noise If you do not hear the igniter sparking you may need to replace the battery Replace with a standard AAA battery directly behind the rubber push button knob unscrew knob to access battery Keep igniter button pushed in while pushing then turning the fuel flow valve to the ON Low flow position at the fire pit The jet pilot fire should light the burner within 15 seconds after the burner lit release the igniter button but still keep pushing the fuel flow valve for 20 seconds to allow the thermocouple to function After the 20 seconds release the fuel flow valve if the burner keeps lit you can adjust the flame to HI However if the flame extincts after the fuel flow valve released Re try or go to trouble shooting and start from Step 1 again TO TURN OFF GAS Turn the ON OFF valve to the off position at the unit then turn the valve on the LP tank or the main shut off valve of natural gas system to the OFF position MAINTENANCE 1 The appliance should be
3. at first sign of leak or age cracking Remember to turn the cylinder valve OFF before removing the hose To connect the city network gas to the unit 1 Attach the hose to the manifold inlet fitting with a national standard NG connector and secure the hose to the manifold inlet fitting Ensure that all connecting threads and surfaces are undamaged and clean When fitting the 13 hose make sure that it is free from twisting kinks or sharp bends Protect the hose from any sharp edges 2 Attach one end of the hose to the main shut off valve of city network gas 3 Do a leak test each time when the gas connection is reconnected If the hose shows deterioration or damage leak test the entire outer surface Remember to turn the city network gas OFF before removing the hose Testing for Leaks 1 Ensure knob is OFF and open the cylinder valve 2 Use a solution of half detergent and half water for leak testing Brush solution on each connection and check for bubbles 3 Ifa leak is present turn off the gas supply and tighten the loose joint 4 If leak persists contact an authorized agent INSTALLATION The gas cylinder enclosure log set and crushed lava rock are shipped together on applicable models Remove the log set and un pack all components Check for damage caused by freight transport DO NOT install damaged components The logs are fragile use care when handling Place the fire pit on a level secure surface in a desired locatio
4. part No 39 is for SRRS065xxl2 and SRRSO40xxI2 series only SRS6510 12 amp SRS4010 12 series exploded AO LRR RAAN RRR SRS6504 12 amp SRS4004 12 series exploded SEE XX KKKX AOA ORRE SRR6501 l2 amp SRR4001 12 series exploded BOO i CET a x XK XXX ZZAN 6666 68 NZ Zs ASSEMBLY INSTRUCTIONS GAS HOSE CONNECTIONS Two adults will be needed to assist each other with assembly SRRSO65xx amp SRRSO40xx Upraise the fire pit and attach the hose to the manifold inlet nipple and tighten hose clip or secure the hose to the manifold inlet fitting as shown in FIG 01 amp FIG 02 below SRRSO65xxl2 amp SRRSO40xx 2 Upraise the fire pit and attach the hose to the manifold inlet fitting with a national standard NG connector and secure the hose to the manifold inlet fitting as shown in FIG 03 below NOTE Installation and service must be performed by a qualified installer service agency or your gas provider ASSEMBLY INSTRUCTIONS INSTALLATION OF LAVA ROCKS AND LOGS Unpack and put the lava rocks on ground Pick up the solid lava rocks then layer them in level across the burner plate Bring it up to a level that is just over top of the burner by about 1 Do not completely cover burner element or block the igniter box with lava rock Next install the imitation fire logs These should be laid in as shown in the image below Start by laying one log in the centre of the unit This log shou
5. Happy Cocooning COCOON TABLES ASSEMBLY INSTRUCTIONS AND SAFETY GUIDE SRRSO65xx I2 amp SRRSO40xx l2 SERIES SRS6510 I2 amp SRS4010 I2 SRS6504 I2 amp SRS4004 12 SRR6501 I2 amp SRR4001 I2 C 0063 11 SRRSO65xx I2 QN 19 KW 1383 g h 13 28 30 37 13 B P 30 13 B P 50 I2L amp 12H 12E 12E SRRSO40xx I2 QN 12 kW 874 g h 13 28 30 37 13 B P 30 amp 13 B P 50 amp 12L SRRSO40xx I2 Z QN 13 KW 747 g h I2H I2E I2E BE CY CZ EE GR IT IE PT ES LU GB FR IS LT PT SK CH Cat l3 Butane G30 28 30 mbar Propane G31 37 mbar Injector SRRSO65xx 2 2 mm SRRSO40xx 1 65mm CY CZ DK EE Fl GR LV LT LU MT NL NO SK SI SE TR HU Cat I B P 30 Butane and Propane mixtures at 30mbar Injector SRRSO65xx 2 2 mm SRRSO40xx 1 65mm AT DE SK CH Cat I B P 50 Butane and Propane mixtures at 50mbar Injector SRRSO65xx 1 9mm SRRSO40xx 1 45mm AT BE CH CZ DE DK EE ES Fl FR GB GR HU IE IT LT LU LV NL NO PL PT RO SE SI SK Cat lo Natural Gas G25 at 25mbar Injector SRRSO65xxl2 4 1mm SRRSO40xxl2 3 0mm 124 l gt ENatural Gas G20 at 20mbar and 125 Natural Gas G20 at 20mbar Natural gas G25 at 25mbar Injector SRRSO65xxI2 3 65mm SRRSO40xxl2 3 0mm Only nationally approved hose and regulator corresponding to the appliance category and pressure must be used This manual is for AT CH DE PIN NO 0063BT7387
6. UEL SUPPLY WARNING DISCONNECT WHEN NOT IN USE AND KEEP OUT OF REACH OF CHILDREN GENERAL INFORMATION WARNING This appliance shall be used ONLY outdoors in a well ventilated space and shall NOT be used inside a building garage or any other enclosed area WARNING This appliance is not approved as a cooking device and should not be used as such WARNING THIS UNIT IS NOT FOR USE WITH SOLID FUELS WARNING Cylinders must be stored outdoors in a well ventilated area out of reach of children Disconnected cylinders must not be stored in a building garage or any other enclosed area 12 WARNING Storage of this appliance indoors is permissible only if it has been disconnected from its fuel supply Always keep the appliance area clear and free from combustible materials gasoline and other flammable vapors and liquids Installation and repair should be done by a qualified service person The appliance should be inspected before use and at least annually by a qualified service person More frequent cleaning may be required as necessary It is imperative the control compartment burner and circulation air passageways of the appliance be kept clean and free If it is evident there is excessive abrasion or wear of any of the components if the fuel supply hose is cut or cracked it must be replaced prior to the appliance being put into operation Children and adults should be alerted to the hazards of high surface temperatures and s
7. ade Note that the unit must be turned upside down to perform this examination It is also important to remove battery from igniter before performing any leak testing by unscrewing the push button knob at the control panel Perform leak test in a well ventilated area outside and where no source of spark can occur 8 If everything is secure and leak free to this point you are ready to light your fire pit Read OPERATION instructions 14 OPERATION Upon completing the gas line connection a small amount of air will be in the lines When the first lighting the burner it will take a few seconds for the lines to purge themselves of this air Once the purging is complete the burner will light and operate as indicated in the instruction manual Subsequent lighting of the appliance will not require such a purging unless the gas supply has been disconnected WARNING Read and follow the safety and lighting instruction page in this manual and on the labels on the appliance BY NOT FOLLOWING INSTRUCTIONS A FIRE EXPLOSION MAY RESULT YOU MAY BE SERIOUSLY INJURED BASIC SET UP Once the fire pit is in position level and safely hooked up to the proper fuel supply it is now time to install the crushed lava rock This is also an essential part of the overall set up as it will impact the way the unit burns if not properly installed Layer the lava rock in level across the burner plate Bring it up to a level that is just over top of the burner by abou
8. ber PVC layer s to cover on it to prevent people from stumbling The proper rubber PVC layers are available from the same dealer or qualified installer lee thle NOTICE TO INSTALLER THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER Outdoor Gas Fire Pits INSTALLATION AND OPERATION INSTRUCTIONS FOR OUTDOOR GAS FIRE PITS WARNING If the information in these instructions is not followed exactly a fire or explosion may result causing property damage personal injury or loss of life Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance WHAT TO DO IF YOU CAN SMELL GAS FUMES Do not try to light any appliance Do not touch any electrical switches Do not use any phone including cellular phones Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions e lf you cannot reach your gas supplier call the fire department Installation and service must be performed by a qualified installer service agency or your gas provider WARNING WARNING Improper installation adjustment alteration service or maintenance can cause injury or property damage Read the installation operating and maintenance instructions thoroughly before installing or servicing this equipment WARNING WARNING FOR OUTDOOR USE ONLY WARNING DO NOT LEAVE ANY OUTDOOR GAS APPLIANCE UNATTENDED WHEN IN USE OR HOOKED UP TO A F
9. hould stay away to avoid burns or clothing ignition Young children should be carefully supervised when they are in the area of the appliance Clothing or other flammable materials should not be hung from the appliance or placed on or near the appliance Any guard or other protective device removed for servicing the appliance must be replaced prior to operating the appliance Inspect the fuel supply connection and all gas tubes for signs of leakage before each use of the appliance The pressure regulator and hose assembly supplied with LP models must be used Replacement pressure regulator and hose assemblies must be those specified in this manual To connect the gas bottle to the unit Appropriate Regulators are available from the same dealers for fitting to the hose supplied with this unit Ensure that all connecting threads and surfaces are undamaged clean and free from oil dirt When fitting the hose make sure that it is free from twisting kinks or sharp bends Do not allow the hose to touch any hot surface or sharp edges 2 Attach the regulator to the gas cylinder Refer to the instructions supplied with the regulator for details regarding fitting 3 Test for gas leaks Do a leak test each time the cylinder is installed whether or not it has been filled Check all other joints and gas tubes at least once a year If the hose shows deterioration or damage leak test the entire outer surface while under pressure Replace
10. inspected before initial use and inspected and cleaned at least annually by a qualified service person 2 Tampering is DANGEROUS and voids all warranties Any component that is found to be faulty must be replaced with an approved component 3 To obtain proper operation it is imperative that the burner flame characteristics are constant not lifting or floating For a clean burn the unit is designed to run at full flow If not operating at full fuel flow black smoke may start to occur Always operate at full fuel flow to burn clean and prevent smoke Dirty logs can be easily cleaned off with water and light soap 4 Periodically remove the logs and examine the burner and its components If dirty clean with a soft brush and soapy water solution Also examine the area around the burner Any dirt or foreign material such as spider webs or nests in this area should be removed This will ensure long life safe and trouble free operation 5 Periodically check the hose connecting the LP gas cylinder to ensure it is not cracked or damaged in any way NOTE Carbon soot may built up on the surface of the logs over time or with extended use This is more likely to occur when using LP gas The soot should be cleaned off the surfaces of the imitation logs periodically to prevent excessive build up To clean the logs be sure the fire is out the gas supply is turned off and the logs are cool to the touch The soot can then be brushed of with a dry bristle b
11. ld be perpendicular to the igniter box and lay on top of the centre support bracket Lay the other logs quantity may vary by unit type in a teepee configuration over the first log It is important that the logs not lay directly on top of the burner By blocking the burner it will impact air flow and will cause the unit to be difficult to ignite or will impact how the flame comes through and burns Once all the logs are in place as shown you can begin next steps NOTE Be sure unit is cool before touching any of the components NOTE When first use preheat the lava rocks for 15 minutes to burn out the impurities and air in the natural lava rocks ASSEMBLY INSTRUCTIONS INSTALLATION OF GAS CYLINDER ENCLOSURE After the well connection to the gas supply cylinder put the enclosure onto the gas cylinder then cover with the lid Align the hose pipe through the holes of passages at the bottom of the fire pit and the enclosure as shown in the image below Note For the hose exposed please be sure to use a rubber PVC layer s to cover on it to prevent people from stumbling The proper rubber PVC layers are available from the same dealer ASSEMBLY INSTRUCTIONS INSTALLATION OF CITY NETWORK GAS Upraise the fire pit and attach the manifold inlet fitting with the national standard NG connector supplied Connection of the NG supply to the appliance inlet should be made by a qualified installer Note For the hose exposed please be sure to use a rub
12. n The location must be adjacent to the gas supply cylinder After the well connection to the gas supply cylinder put the enclosure onto the gas cylinder then cover with the lid NOTE Minimum clearances 1 meter to combustible construction must be maintained You must have clear and easy access to the on off valve AFTER the appliance is installed and connected to the gas supply in order to safely turn of the burner THE ON OFF VALVE IS USED TO TURN THE BURNER ON AND OFF 1 Cylinder should be positioned on a flat level surface near the fire pit but within the pre described safe distance 1 meter away 2 Make sure the tank valve is in its full off position 3 Never attempt to use damaged or plugged equipment See your local LP Gas Dealer for repairs 4 Connect and tighten the end to the gas regulator with the clip 5 When connecting regulator assembly to the tank valve hand tighten it to a positive stop 6 Locate the hose out of the pathways where people may trip over it or in areas where the hose may be subjected to accidental damage 7 Open tank valve fully Turn the on off valve at the unit to the off position to pressurize the hose assembly Use a soapy water solution to check all the connections between the gas tank connection and the ball valve at the back of the control panel for leaks before attempting to light the appliance If a leak is found turn the tank valve off and do not use the appliance until repairs can be m
13. not move this fire pit during use 17 Turn off the gas supply after use 18 Do not touch the logs or lava rocks until they cool down 19 This appliance is intended for warming purposes 20 This appliance has a naked flame a suitable guard should be used for the protection of young children the elderly and the infirm 21 When first use preheat the lava rocks for 15 minutes to burn out the impurities and air in the natural lava rocks Contents 1 Technical Data Page 2 3 2 Instructions for assembly Page 4 7 3 Installation and operation instructions Page 8 11 4 Maintenance Page12 16 The gas fire pits are 13 28 30 37 13 B P 30 13 B P 50 l2L G25 amp I2H I2E I2E G20 appliances designed to operate on Butane at 28 30mbar Propane 37mbar B P 30 50mbar 12L at 25mbar amp I2H I2E I2E at 20mbar Gas consumption pressures and injectors orifices sizes are shown below SRRSO65xx I2 GAS FIRE PITS Injector Orifice Heat Input Hs Gas Rate 13 28 30 37 13B P 30 2 2mm 19 kW 1383 g h 13 B P 50 1 9mm 19 kW 1383 g h l2L 4 1mm 19 kW 2 1m3 h I2H I2E I2E 3 65mm 19 kW 1 8m3 h SRRSO40xx I2 GAS FIRE PITS Injector Orifice Heat Input Hs Gas Rate 13 28 30 37 13B P 30 1 65mm 12 kW 874 g h 13 B P 50 1 45mm 12 kW 874 g h I2L 3 0mm 12 kW 1 3m3 h 12H 12E 12E 3 0mm 13 kW 1 2m3 h LP Gas Regulator A gas regulator confirming to the national standard must be fitted t
14. o the gas cylinder to provide the appropriate gas pressure The supply pressure of the LPG regulator must comply with the table blow 13B P 30 13B P 50 13 LPG LPG Butane Propane 28 30mbar 50mbar 28 30mbar 37mbar Do Not use this appliance with an adjustable regulator We suggest use this appliance with LP gas cylinder of 10KG 2 Instructions for assembly Read these instructions through carefully before commencing assembly and then follow them step by step SRRSO65xx l2 amp S RRSO040xx 12 series parts list No Description Q TY No Description Q TY 01 Knob 1 21 Aluminum tube 1 02 Valve 1 22 Thermocouple 1 03 ISS flexible tube 1 23 Pulse battery box 1 04 Injector fitting 1 24 Pipe clamp 1 05 Prop plank 1 25 Inlet fitting 1 06 Fix plank Burner plate 3 26 Nut Inlet fitting 1 07 Igniter needle 1 27 Igniter box 1 08 Burner plate 1 28 oe 1 09 Fix plank Burner head top 2 29 Log set 4 10 Pilot Igniter 1 30 Nut M8 6 11 Burner head 1 31 Screw M8F40 1 12 Fix plank Burner head bottom 1 32 Nut M6 2 13 Windpipe 1 33 Screw M5F20 6 14 Windscreen 1 34 Nut M5 6 15 Support tube Burner plate bottom 3 35 Washer 4 16 Nut Pilot Igniter 1 36 Screw M4F08 6 17 Washer 1 37 iControl panel 1 18 Spring 1 38 Pit body 1 19 Support plank 1 39 Gas Inlet fitting 1 20 Contactor 1 Note The
15. ren well clear while fire pit is in use and after use until it has cooled 8 9 Never obstruct free flow of air to the fire pit or alter adapt the fire pit to suit any other Keep warming area clear of combustible materials and or liquids situation 10 SRRSO65xx amp SRRSO40xx A hose conforming to the national standard must be connected at one end to the LPG regulator and at the other to the fire pit nipple using hose clips The hose length is 2 5m For the hose exposed please be sure to use a rubber PVC layer s to cover on it to prevent people from stumbling The proper rubber PVC layers are available from the same dealer SRRSO65xxl2 amp SRRSO40xxl2 A hose conforming to the national standard must be connected at one end to the main shut off valve of city network gas and at the other to the 1 fire pit inlet with a national standard NG connector For the hose exposed please be sure to use a rubber PVC layer s to cover on it to prevent people from stumbling The proper rubber PVC layers are available from the same dealer or qualified installer 11 Lead the hose away from the fire pit without twisting it Do not let the hose touch the hot surface 12 Never change the air valve settings of the burner 13 Every time the gas connection is reconnected do a leak test 14 That parts sealed by the manufacturer or the agent must not be altered by the user 15 Any modification of this gas fire pit may be dangerous 16 Do
16. rush or cloth Take care while cleaning the logs as they can become damaged if mishandled Care should be taken to dispose of the soot and the cleaning materials properly Keep away from clothing and outdoor furniture During the cold winter months or in colder climates it is recommended to disconnect the fire pit and store it in a cool dry place Do not store the LP gas tank inside For the balance of the year protect and cover your fire pit from the rain freezing rain or heavy snow by using the custom cover than comes with the kit Before installing the cover make sure the unit is shut off that the gas lines are disconnected and that the unit has had sufficient time to cool Install the cover and use the tie down straps to secure it tightly to the unit to prevent the wind from blowing it off Produced on behalf of HAPPY COCOONING B V Provinci nbaan 1 5121 DK Rijen 16 The Netherlands Tel 31 0 161 750270 Fax 31 0 161 750375 17
17. t 1 Do not completely cover burner element or block the igniter box with lava rock Next install the imitation fire logs These should be laid in as shown in the image above Start by laying one log in the centre of the unit This log should be perpendicular to the igniter box and lay on top of the centre support bracket Lay the other logs quantity may vary by unit type in a teepee configuration over the first log It is important that the logs not lay directly on top of the burner By blocking the burner it will impact air flow and will cause the unit to be difficult to ignite or will impact how the flame comes through and burns Once all the logs are in place as shown you can begin next steps NOTE Be sure unit is cool before touching any of the components ce YOUR SAFTY READ BEFORE LIGHTING A Before operating smell all around the appliance area for gas odors and next to the floor because some gases are heavier then air and will settle on the floor B Use only your hand to turn the manual gas control valve Never use tools If the valve will not turn by hand do not try to repair it Call a qualified service technician Force or attempted repair may result in a fire or explosion C Do not use this appliance if any part has been under water Immediately call a qualified service technician to water WHAT TO DO IF YOU SMELL GAS e Donot try to light any appliance e Donot touch any electric switch do not use any phone in your building
Download Pdf Manuals
Related Search