Rerun Architectural User Manual
Contents
1. FLASH ON ON ON FLASH ON ON ON ON ALL FLASH GREEN PAUSE LED OFF OFF OFF ON ON ON OFF OFF OFF ON ON ON ON ON ON FLASH GREEN LOOP LED OFF OFF OFF OFF ON ON OFF OFF OFF OFF ON N A N A N A N A N A FLASH ILLUMINATED LED EXTINGUISHED LED SHOW LEDS 1 THOUGH 10 ILLUMINATED ONCE PER SECOND CONTINUOUSLY ILLUMINATED ONCE PER SECOND CONTINUOUSLY ILLUMINATED ONCE ONLY YELLOW START LED OFF OFF OFF OFF OFF OFF OFF OFF OFF N A N A FLASH ON N A N A FLASH YELLOW RED END RECORD LED LED OFF OFF OFF OFF ON OFF OFF OFF OFF OFF BLINK OFF OFF ON OFF ON OFF FLASH N A OFF N A OFF N A OFF N A OFF FLASH OFF ON OFF FLASH FLASH Page 7 of 12 STATE UNIT NOT POWERED PLAYBACK OF PRESET PLAYBACK AT END POINT PLAYBACK PAUSED SHOW SET TO LOOP OR LINK SHOW AT END POINT AND LOOPED TO START POINT RECEIVING DMX512 THE RERUN A IS LOCKED OUT FROM RUNNING SHOWS AND IS PASSING CONSOLE DATA TO THE OUTPUT RECEIVING DMX512 READY TO RECORD SHOW CURRENTLY BEING RECORDED LOOP STATUS IN SHOW RECORD ON ENABLED OFF DISABLED ON SELECTED SHOW FLASH SHOW TO LINK TO PLAYBACK POINTER AT START OF RECORDED SHOW PLAYBACK POINTER AT START POINT PLAYBACK POINTER AT END OF RECORDED SHOW PLAYBACK POINTER AT END POINT COMPACT FLASH CARD NOT2. It does not include damage due to misuse or abuse Most non warranty repairs are made for a fixed 30 00 fee Page 12 of 12
3. Press and hold the recessed RECORD button A paper clip can be used to push this button While holding the RECORD button press one of the show buttons to choose which show will play after the current one The LED for that show will flash and the LED for the current show will remain on solid 5 Press the PAUSE button to save the new settings and to resume the show When the show you just edited finishes playing the linked show will begin playing The link and loop status of the next show will be executed with the new show Note Tore link a show to itself simply edit the link as described above but select the current show as the show to be linked The current show LED will stay on solid and all other show selection LED s will turn off e Turning off the loop feature also disables the link function for the current show When paused the loop link status for the current show displayed Page 11 of 12 WARRANTY Products manufactured by Doug Fleenor Design carry a five year parts and labor warranty against manufacturing defects lt is the customer s responsibility to return the product to Doug Fleenor Design at the customer s expense Doug Fleenor Design will repair the unit and return it to the customer at Doug Fleenor Design s expense If a trip is necessary to the customer s site to solve a problem the expenses of the trip must be paid by the customer Note that this warranty is against Manufacturing Defects
4. operation The factory default is to have all jumpers installed JP1 Record Lockout When removed the RECORD button is disabled When installed recording of presets is enabled JP2 Hold Last Look When removed upon the loss of signal the last valid input is held on the output When installed upon the loss of signal the last active show is started JP3 Hardware Test When removed the Rerun Architectural enters the hardware test mode JP4 Disable When removed the Rerun Portable will be disabled JP3 Unused JP4 CF Card initialize When removed the memory card is erased Use with CAUTION REMOTE SHOW RECALL PANEL Remote control of the Rerun Architectural system is accomplished by use of a Preset 10 Architectural model PRE10 A panels The remote panel provides ten show buttons and twelve indicators Figure 1 Multiple remote panels can be connected in a daisy chain manner to the DMX512 input on the Rerun Architectural The remote panel must be configured as a slave To configure a Preset 10 Architectural as a slave the jumpers located at JP2 and JP4 must be removed Figure 2 For safe keeping place the jumper over only one of the pins at JP2 and JP4 SHOW INDICATOR GREEN SHOW BUTTON END INDICATOR YELLOW INPUT LOCKOUT INDICATOR RED Figure 2 Figure 1 Page 6 of 12 INDICATORS ON OFF ALL FLASH FLASH BLINK GREEN SHOW LED OFF ON ON ON ON ON OFF ALL
5. 512 data DMX512 data ESD protected EIA 485 transceiver LT1785 ESD protected EIA 485 transceiver LT1785 None DMX input is not isolated from DMX output INSTALLED REMOVED Recording editing disabled Hold last look on DMX512 loss Run hardware test Disable operation Unused Erase memory DANGER SPECIFICATIONS CONTINUED Power input Color Size 2 L11 4 5 203 ogg 709 819 8 208 1000 10 to 15 volts AC or DC 150 mA per station A 10 volt class 2 doorbell transformer is recommended for fixed installations Black anodized with silver engraved nomenclature Faceplate 4 5 h X 4 6 w X 0 2 d Faceplate rear inset 4 15 h X 4 25 w X 0 1 d Electrical box minimum inside dimensions 2 9 h X 3 5 w X 1 5 d POWER OM OUTPUT DMA INPUT POWER SUPPLY The voltage provided to the Rerun Architectural must be between 10 and 15 volts AC or DC The Rerun Architectural has been designed to operate on a standard class 2 doorbell transformer For example Ace Hardware s model ACE36483 10 volt 5 watt transformer Doorbell Transformer Page 4 of 12 WIRING INFORMATION Rerun Architectural is designed to use daisy chain wiring topology Please give us a call if you have any questions Note If Rerun Architectural is not powered DMX512 from console will not pass through ___ COLOR FROM TO USE Shield Pin 1 DMX IN Common 1 e
6. DOUG FLEENOR DESIGN RERUN ARCHITECTURAL DMX512 RECORDER MODEL RERUN A OWNERS MANUAL Doug Fleenor Design 396 Corbett Canyon Road Arroyo Grande CA 93420 805 481 9599 Software Version 1 0 Manual Revision 0 gt Serial 069177 PRODUCT DESCRIPTION The Rerun Architectural is a lighting control station capable of storing up to ten 40 minute shows Shows are recorded by capturing the output of a DMX512 console The recorded show start and end points may be trimmed non destructively Each show can be set to hold the last look loop to itself or link to another show Shows are started by pressing one of the ten show buttons The basic system consists of a Rerun Architectural station and a power supply The solid aluminum faceplate is designed to install over a standard two gang electrical box Single gang remote stations can be added to remotely select shows Connections to the Rerun Architectural are power 2 wires DMX512 Input 3 wires and DMX512 Output 3 wires Power for the Rerun Architectural can be supplied from a variety of sources including a 10V class 2 doorbell transformer The Rerun Architectural system can work in conjunction with a lighting console automatically switching between recorded shows and console control When the console generates DMX512 the Rerun Architectural retransmits the incoming DMX512 data Thus the console operates normally Upon loss of DMX512 from the console the Rerun Architectural starts its p
7. FOUND THE ANATOMY OF A SHOW The Rerun Architectural has ten show memories each capable of recording 40 minutes of DMX512 data Within each show memory are non destructive trim points called the START POINT and the END POINT The show memory is the data space used to store the show Its time line always starts at the top of the show memory The point at which the SHOW button was pressed to begin recording The show time line continues until the bottom of the show the point at which the SHOW button was pressed to stop recording or when the recorded show exceeds the show memory at 40 minutes The START POINT is the point at which your show will begin to playback when the SHOW button is depressed The END POINT is the point at which the show will end By default when you record a show the START POINT and END POINT are positioned at the top and bottom of the recorded show Figure 1 The START POINT and END POINT can be moved to any time within the recorded show allowing you to non destructively trim the show Figure 2 START END SN END POINT POINT POINT POINT RECORED SHOW RECORED SHOW 5 10 15 20 25 30 35 SHOW MEMORY SHOW MEMORY Figure 1 Figure 2 RECORDING SHOWS In order to capture the individual channel levels recorded to a show the Rerun Architectural must be connected to a DMX512 source It is recommended that your console output all 512 slots When fewer than 512 slots are received a level of 0 will be stored for all slots above t
8. LED will illuminate adjacent to the button that was pressed Selecting another show will immediately start the new show from its START POINT and stop the currently running show When a show comes to its end the END LED will illuminate Iflooping has been enabled the END LED will blink and the show will start over from its START POINT If looping has not been enabled the Rerun Architectural will continue sending the last levels of the current show until another show is selected Note e If a show is playing at the time power is lost Rerun Architectural will return to the start of that show when power is restored If Rerun Architectural is not powered DMX512 from console will not pass through Pausing a show A running show can be paused by pressing the PAUSE button When a show is paused the PAUSE LED will illuminate and the Rerun Architectural will continue sending the current DMX512 values for that point in the show While paused various show parameters can be edited See the section on show editing for details A paused show can be resumed by pressing the PAUSE button again The PAUSE LED will extinguish and the show will continue playing from the point at which it was paused Looping a show When a show is selected its recorded loop status is loaded This is indicated by the LOOP LED f desired the loop status of a show can be temporarily over ridden While the show is running push the LOOP button This will toggle the te
9. POINT do the following 1 Start playing the show to be edited 2 Pause the show near the desired END POINT 3 While paused use the REWIND or FORWARD button to move the playback pointer and locate the desired END POINT 4 Press and hold the recessed RECORD button A paper clip can be used to push this button While holding the RECORD button press the FORWARD button After it is pressed the END LED will turn on indicating that this point in the show is the END POINT Note The POINT is set to the bottom of the show when that show is first recorded e The END POINT must be set to a point in the show after the START POINT If you attempt to set the END POINT to a point before the START POINT the set END POINT command will be ignored e Once recorded show data is never discarded If you set an END POINT a few minutes before the bottom of a recorded show those minutes of data still exist You can start the show pause it and forward into the previously trimmed out area A new END POINT can then be set Page 10 of 12 EDITING SHOW PARAMETERS CONTINUED START END POINT EOF RECORED SHOW SHOW MEMORY Looping By default shows are not looping This means that when the show comes to its end the show stops and the Rerun Architectural will send the last levels of the show until another show is selected When looping is enabled the show will automatically re start itself and run in a continuous loop The loo
10. hose received To allow you to observe the show being recorded the Rerun Architectural echos data being received on its output port 1 Using the primary DMX512 console go to the beginning of the show to be recorded 2 Using a small blunt object i e paper clip depress the recessed RECORD button located next to the REDLED The SHOW LEDs will begin to flash and the RECORD LED will illuminate If you decide after depressing the RECORD button that you do not wish to record a show depress the RECORD button a second time No changes will have been made 2 Depress the SHOW button adjacent to the show number you wish to record The show will immediately begin recording The adjacent SHOW LED will indicate the show being recorded and the RECORD LED will flash A To stop recording depress the SHOW button adjacent to the show number you are recording Repeat steps 1 through 4 until you have recorded as many shows as desired up to ten total Note If Rerun Architectural is not powered DMX512 from the console will not pass through Page 8 of 12 PLAYBACK OF SHOWS Recorded shows may not be played when there is incoming DMX512 When DMX512 from a console is present the Rerun Architectural s RED LED will be on and the only action possible is recording a show Playing a show Shows are played by pressing one of the SHOW buttons When a SHOW button is pressed that show will immediately begin playing from its START POINT The SHOW
11. illflash When the playback pointer is atthe START POINT the START LED willturn on solid When the playback pointer is at the end point the END LED will turn on solid See below for the meanings of these terms and for details on editing them START POINT The START POINT is the point in the show at which playback will begin when that show is selected To setthe START POINT do the following 1 Start playing the show to be edited 2 Pause the show near the desired START POINT 3 While paused use the REWIND or FORWARD buttons to move the playback pointer and locate the desired START POINT 4 Press and hold the recessed RECORD button A paper clip can be used to push this button While holding the RECORD button press the REWIND button After it is pressed the START LED will turn on indicating that this point in the show is the start Note e The START POINT is set to the top of the show when that show is first recorded e The START POINT must be set to a point in the show before the END POINT If you attempt to set the START POINT to a point after the END POINT the set START POINT command will be ignored e Once recorded show data is never discarded If you set a START POINT a few minutes into a recorded show those minutes of data still exist You can start the show pause it and rewind into the previously trimmed out area A new START POINT can then be set End point The END POINT is the end of the show To set the END
12. mporary state of the LOOP LED If the show was looping the LOOP button will cancel the loop If it was not looping the LOOP button push will enable looping Pressing the show button will reload the recorded loop status for the show and re start the show from its START POINT Changing the loop status while a show is running is temporary and is not recorded with the show Note Looping also be recorded into the show This is covered in the editing show parameters section of the manual SHOW NUMBER 10 SPECIAL FUNCTION When show number 10 ends and is not set to loop the Rerun Architectural will stop sending DMX512 data By going off line many moving lights and dimming systems will detectthe loss of DMX512 and begin their shut down routines Page 9 of 12 EDITING SHOW PARAMETERS A number of parameters can be edited in recorded shows These include the start point end point looping linking status and linked show number Setting start and end points The REWIND and FORWARD buttons are used to set the start and end points These buttons are only active while a show is paused When paused the buttons can be used to move the playback pointer forward or backward through the show The longer each button is held the faster the show will be forwarded or rewound When the playback pointer is at the top of the recorded show the START LED will flash When the playback pointer reaches the bottom of the recorded show the END LED w
13. n White Blue XLR Plate Pin 2 DMX IN Data ZEE Pin 3 RERUN A DMX IN Data 2 2 16 AWG Black Common PWR DMX OUT Supply Power Supply Stranded Wires Power PAREM on Supply hot Shield PWR DMX OUT Common 120 Ohm Data Cable Dimmer 5 Belden 9829 or Equivalent INSE NE HESSE L did Tof Cabinet Hata Blue W hite PWR DMX OUT ol Data 120VAC PSU DIMMERS OPTIONAL REMOTE PANEL CABLE COLOR FROM ro USE Shield Pin 1 TB1 1 Common 120 Ohm Data Cable a i 1 sie ER on Ie uelle W hite Blue XLR Plate Pin 2 TB1 2 Data Blue W hite Buewnte Pin 3 acie TB1 3 Data Slave 2 16 AWG Black Common TB1 4 Supply 2 Stranded Wi Power Supply rae Power TB1 5 Supply hot Shield TB1 1 DMX IN Common 3 120 Ohm Data Cable DMX IN B Belden 9829 or Equivalent TEI aas Blue W hite oo TB1 3 RERUN A DMX IN Data 4 6 Awe Black TB1 4 PWR DMX OUT Supply Skranded Wires Le f TB1 5 PWR DMX OUT Supply Hot Shield PW R DMX OUT Common 120 Ohm Data Cable RERUN A Dimmer Data Blue W hite PW R DMX OUT Data 1 DIMMERS Page 5 of 12 RERUN ARCHITECTURAL FACEPLATE CONFIGURATION Each Rerun Architectural has six jumpers JP1 through JP6 that select different modes of
14. ping feature can be temporarily enabled or disabled as described in the show playback section To permanently change a show s looping status do the following 1 Start playing the show to be edited 2 Pause the show at any point The LOOP LED will immediately display the recorded status of the looping feature for that show When the LOOP LED is on looping is enabled 9 Press hold the RECORD button paper clip be used to push this button While holding the RECORD button press the LOOP button After it is pressed the LOOP LED will change indicating the shows new looping status 4 Press the PAUSE button to save the new loop status with the show and to resume playing Note e When a show selection button is pressed the loop status will be updated from the recorded show data This will override any manual looping selections made previously START END POINT POINT LINK RECORED SHOW SHOW MEMORY Linking This feature is for advanced users only Linking is similar to show looping However with linking when a show reaches its end instead of looping to re start itself a different show is started You can select which show is linked This powerful feature allows the user to create longer and more complex shows To link shows do the following 1 otart playing the first show 2 Pause the show at any point 9 If itis not enabled already enable looping for the show Looping section above 4
15. revious show Rerun also comes in an portable version model RERUN P and a rack mount version model RERUN RM SHOW BUTTON PAUSE BUTTON SHOW INDICATOR GREEN LOOP BUTTON PAUSE INDICATOR GREEN REWIND BUTTON LOOP INDICATOR GREEN FORWARD BUTTON START INDICATOR YELLOW RECESSED RECORD BUTTON END INDICATOR YELLOW INPUT RECORD INDICATOR RED Page 2 of 12 SPECIFICATIONS Terminal block 1 Phoenix Contact MSTB series 5 position two part terminal block Model MSTB 2 5 5 ST 5 08 Order number 17 57 04 8 Connector Connector pin out Terminal Block 1 DMX512 Output 1 C DMX512 common 2 DMX512 data DMX512 data 4 C Supply common internally tied to pin1 5 V Supply voltage hot Input Circuit Output Circuit Isolation Indicators Ten green SHOW LEDs One green PAUSE LED One green LOOP LED One yellow START LED One yellow END LED One red INPUT RECORD LED User controls Ten SHOW buttons One PAUSE button One LOOP button One REWIND button One FORWARD button One recessed RECORD button Option Jumpers JP1 Recording enabled JP2 show on DMX512 loss JP3 Normal operation JP4 Normal operation JP Unused JP6 Normal operation Page 3 of 12 Terminal block 2 Phoenix Contact MSTB series 3 position two part terminal block Model MSTB 2 3 G 5 08 Order number 17 55 74 9 Terminal Block 2 DMX512 Input C DMX512 common DMX
Download Pdf Manuals
Related Search