USER`S MANUAL
Contents
1. Packets sending receiving on TX port FDX Col On TX port Full duplex mode active Off TX port Half duplex mode active FX or SD On Fiber signal is detected 1000M On TX in 1000M speed Off TX in 100M speed Rear Panel Please refer to the following description for the rear panel Dip switch settings ON OFF FUNCTION DIP1 DIP 4 LFP function is enabled by DIP 1 ON DIP 4 OFF or DIP 1 OFF DIP 4 ON they have to be in reverse pa DIP 4 DIP 1 Default setting is DIP 1 ON DIP 4 OFF DIP2 Pass through mode and enable jumbo frame DIP3 DIP2 DIP3 Enable Store and Forward mode Default DIP2 DIP3 Modified cut through mode Specification IEEE 802 3 for 10 BASE T IEEE 802 3u forl00 BASE TX FX TEEE802 3ab for 1000M BASE TX TEEE802 3E AN Standard Interface 10 100 1000M TX 1000M FX SC SFP fiber Fiber interface SX MM LX SM 1000M SFP Multi Mode 50 125 62 5 125um 550Meter avelength 850nm Single Mode 8 3 125 8 7 125um 8 125 10 125um 10K avelength 1310 1550 nm Referenced Dual fiber MM SX 1000M 550m ransmission Dual fiber SM LX 10km Distance Network Speed For TX 10 100 1000 Mbps Auto negotiation For FX 1000Mbps IEEE802 3x flow control for full duplex model Back pressure flow control for half duplex mode Flow Control Dimension 93mm L 69 5mm W 26mm H Operating 0 C 50 C emperature Storage 40 C 70 C 40 F 158 F Operating 10 90 RH n2. Global Systems Solutions 10 100 1000M Media Converter GEP 5301TF C 10 100 1000M Media Converter with Multimode 550M SC GEP 5401TF C 10 100 1000M Media Converter with Single Mode 10KM SC USER S MANUAL FCC MARKING This Equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CE MARKING This equipment complies with the requirements relating to electromagnetic compatibility EN 55022 class A for ITE the essential protection requirement of Council Directive 2004 108 EC on the approximation of the laws of the Member States relating to electromagnetic compatibility Compan
3. on condensing Storage 5 95 RH non condensing Power Supply AC 100 240V 50 60Hz output 5V 1A a 3 lt TH MI FCC CE RoHS
4. y has an on going policy of upgrading its products and it may be possible that information in this document is not up to date Please check with your local distributors for the latest information No part of this document can be copied or reproduced in any form without written consent from the company Trademarks All trade names and trademarks are the properties of their respective companies Copyright 2013 All Rights Reserved Key Features Vv Vv V WV Vv Vv V V WV Complies with IEEE 802 3 IEEE820 3U IEE802 3ab IEEE802 3E AB standard for 10M 100M and 1000M Up to 6 LED s for status indication Support LFP Link Fault Pass through 2M memory buffer built in Supports full and half duplex Mode for 10 100M and full duplex for 1000M Support low delay time pure data transmission Support back pressure flow control for Half Full duplex Supports auto MDI MDI X crossover detecting and auto correction External power adapter 5VDC 1 0 A RoHS compliant Fiber Optic Models wavelength Optical power Sensibilit nm dbm dbm 850 12 15 lt 20 1310 3 8 lt 22 Front Panel Please refer to the following description for the front panel PWR 1000M Linky Act p FOX coL LED Definition LED Status Operation Power On Power is on Link Act On Fiber link port is connected PB Flash Packets sending receiving Link Act On TX port is connected E Flash
Download Pdf Manuals
Related Search