User`s Manual - Postorg.com.ua
Contents
1. Supplement Digits 2 Digits 5 Digits 2 Digits or 5 Digits None ISBN ISSN Conversion Convert EAN 13 to ISBN ISSN Do Not Convert EAN 13 to ISBN ISSN 40 Code ID setting Code ID is a one or two character string used to represent the symbol upon a succeeding reading If you want application to transmit Code ID you must set Code ID transmission to be enabled Refer to the chapter of Scan Code ID 2Bit 00 FF 65 e C Insert String 1 Selection Scan one digits parameter 0 6 that 0 no string insert to the barcode 1 6 insert to the barcode G1 G6 to the barcode Scan Insert String 1 1Bit 0 6 0 Insert String 2 Selection Scan Insert String 2 1 Digit 0 6 0 41 EAN 8 Enable Disable EAN 8 Enable EAN 8 Disable EAN 8 EAN 8 Check Digit Verification Enable EAN 8 Check Digit Verification Disable EAN 8 Check Digit Verification EAN 8 Check Digit Transmission Transmit EAN 8 Check Digit L Do Not Transmit EAN 8 Check Digit 42 Supplement Digits 2 Digits 5 Digits 2 Digits or 5 Digits None Expand EAN 8 to EAN 13 Expand EAN 8 to EAN 13 Do Not Convert EAN 8 to EAN 13 43 Code ID setting d Scan Code ID 2 Digits 00 FF 64 Insert String 1 Selection Scan Insert String 1 1 Digit 0 6 02. Code ID setting c Scan Code ID 2 Digits 00 FF 63 Insert String 1 Selection Scan Insert String 1 1 Digit 0 6 0 Insert String 2 Selection Scan Insert String 2 1 Digit 0 6 0 50 Code128 C Enable Disable Code128 Enable Code 128 Disable Code 128 Code128 Check Digit Verification Enable Code 128 Check Digit Verification Disable Code 128 Check Digit Verification Code 128 Check Digit Transmission Transmit Code 128 Check Digit Do Not Transmit Code 128 Check Digit 51 Code128 Length Scan Max Code Length 2 Digits 00 99 99 Scan Min Code Length 2 Digits 00 99 1 Code ID setting g Scan Code ID 2 Digits 00 FF 67 Insert String 1 Selection Scan Insert String 1 1 Digit 0 6 0 Insert String 2 Selection Scan Insert String 2 1 Digit 0 6 0 52 UCC EAN 128 Enable Disable UCC EAN 128 Enable Disable UCC EAN 128 Check Digit Verification Enable Disable UCC EAN 128 Check Digit Transmission Transmit UCC EAN 128 Check Digit Do Not Transmit UCC EAN 128 Check Digit 53 UCC EAN 128 Length Scan Max Code Length 2 Digits 00 99 99 Scan Min Code Length 2 Digits 00 99 1 Code ID setting rei
3. Scan preamble 0 16 Chars 2 Digits Char 00 FF 00 Postamble Transmit Postamble Do Not Transmit Postamble Scan Postamble 0 16 Chars 2 Digits Char 00 FF 00 Code ID Transmit Proprietary ID Transmit AIM ID 89 Do Not Transmit Code ID Code ID position Before code data After code data Code name transmission Transmit Code name Do Not Transmit Code name Code length transmission Transmit Code length Do Not Transmit Code length 90 Case conversion The characters within code data or the whole output string can be set in either upper case or lower case Disable Upper data only Lower data only Upper whole string Lower whole string Insert String G1 Setting Scan Inert String G1 0 16 Chars 2 Digits Char 00 FF 00 Scan the Position of G1 2 Digits 00 99 00 91 Insert String G2 Setting Scan Inert String G2 0 16 Chars 2 Digits Char 00 FF 00 Scan the Position of G2 2 Digits 00 99 00 Insert String G3 Setting G3 is also used as the string to be replaced when the replace function is enabled Scan Inert String G3 0 16 Chars 2 Digits Char 00 FF 00 Scan the Po
4. Insert String 2 Selection Scan Insert String 2 1 Digit 0 6 0 44 UPC A Enable Disable UPC A Enable UPC A 0 Disable UPC A UPC A Check Digit Verification Enable UPC A Check Digit Verification Disable UPC A Check Digit Verification UPC A Check Digit Transmission Transmit UPC A Check Digit Do Not Transmit UPC A Check Digit 45 Supplement Digits 2 Digits 5 Digits 2 Digits or 5 Digits None UPC A Truncation Expansion Expand UPC A to EAN 13 Truncate leading zeros None 46 Code ID setting b Scan Code ID 2 Digits 00 FF 62 Insert String 1 Selection Scan Insert String 1 1 Digit 0 6 0 Insert String 2 Selection Scan Insert String 2 1 Digit 0 6 0 47 UPC E Enable Disable UPC E Enable UPC E Disable UPC E UPC E Check Digit Verification Enable UPC E Check Digit Verification Disable UPC E Check Digit Verification UPC E Check Digit Transmission Transmit UPC E Check Digit Do Not Transmit UPC E Check Digit 48 Supplement Digits 2 Digits 5 Digits 2 Digits or 5 Digits None UPC E Truncation Expansion Truncate leading zeros Expand UPC E to EAN 13 Expand UPC E to UPC A None 49
5. 58745 8765 4325 abcdefghijklmnopgrstuvwxyz Appendix 2 Default setting for each barcode Table 2 Default setting for each barcode Code type Read Check Check digit Min Proprietary AIM enable digit transmission code code ID verification length EAN 13 y y 13 le Em EAN 8 y y 8 d Em 96 ISBN ISSN1 y y y 13 le Em UPC A y y y 12 b JEm UPC E y y y 8 e Em Code 128 y y 1 g Cm UCC EAN 128 y y 1 q Cm Code 93 y y 1 h Gm Code 39 y 4 1 a Am Code 11 y y 4 m Interleaved 20f5 V 6 i Um Industrial 2 of 5 y 4 j Um Matrix 2 of 5 y 3 2 6 x Jim China Post y y ll jy Um Codabar y 5 k Fm MSI Plessey y 4 f Mm UK Plessey y 1 u Mm GS1 DataBar a 16 r em GS1 DataBar o 16 r Jem Truncated3 GS1DataBar vV e a 16 s Jem Limited GS1 DataBar V i 2 1 p Jem Expanded PDF417 gt 2 o 1 n Lm MicroPDF417 i 1 w Lm NOTE 97 1 The settings for ISBN ISSN and EAN 13 must be the same 2 Fixed length barcodes 3 The settings for GS1 DataBar Truncated and GS1 DataBar must be the same Appendix 4 Decode zone High Density series 98 S Omm r pi 85mm 13mil 10mm FK m 150mm 25mm a DI A 465mm 445mm wu Zu 295mm Dmm 100mm 200mm 300mm 400mm Long Range series 99 300mm 200mm 100mm
6. Scan Code ID 2 Digits 00 FF 67 Insert String 1 Selection Scan Insert String 1 1 Digit 0 6 0 Insert String 2 Selection Scan Insert String 2 1 Digit 0 6 0 54 Code 39 Enable Disable Code 39 Enable Disable Code 39 Check Digit Verification Enable Disable Code 39 Check Digit Transmission Transmit Code 39 Check Digit Do Not Transmit Code 39 Check Digit 55 Code 39 Full ASCII Conversion Enable Code 39 Full ASCII Disable Code 39 Full ASCII Start End transmission Enable Code 39 Start End transmission Disable Enable Code 39 Start End transmission Convert Code 39 to Code 32 Enable Convert Code 39 to Code 32 Disable Convert Code 39 to Code 32 56 Code 32 Prefix A transmission Enable Code 32 Prefix A transmission Disable Code 32 Prefix A transmission ST as data character Enable Disable Code39 Length Scan Max Code Length 2 Digits 00 99 99 Scan Min Code Length 2 Digits 00 99 1 57 Code ID setting a Scan Code ID 2 Digits 00 FF 61 Insert String 1 Selection Scan Insert String 1 1 Digit 0 6 0 Insert String 2 Selection Scan Insert String 2 1 Digit
7. Scan Max Code Length 2 Digits 00 99 99 Scan Min Code Length 2 Digits 00 99 1 79 Code ID setting u Scan Code ID 2 Digits 00 FF 75 Insert String 1 Selection Scan Insert String 1 1 Digit 0 6 0 Insert String 2 Selection Scan Insert String 2 1 Digit 0 6 0 80 GS1 DataBar GS1 DataBar Truncated GS1 DataBar Truncated is structured and encoded the same as the standard GS1 DataBar format except its height is reduced to a 13 modules minimum while GS1 DataBar should have a height greaterthan or equal to 33 modules Enable Disable GS1 DataBar Enable Disable Conversion Convert GS1 DataBar to UCC EAN 128 Convert GS1 DataBar to UPC A or EAN 13 Disable Conversion 81 Code ID setting r Scan Code ID 2 Digits 00 FF 72 Insert String 1 Selection Scan Insert String 1 1 Digit 0 6 0 Insert String 2 Selection Scan Insert String 2 1 Digit 0 6 0 82 GS1 DataBar Limited Enable Disable GS1 DataBar Limited Enable Disable Conversion Convert GS1 DataBar Limited UCC EAN 128 Convert GS1 DataBar Limited UPC A OR EAN 13 Disable Conversion 83 Code ID setting s Scan Code ID 2 Digits 00 FF 73 Insert S
8. i Scan Code ID 2 Digits 00 FF 69 Insert String 1 Selection Scan Insert String 1 1 Digit 0 6 0 Insert String 2 Selection Scan Insert String 2 1 Digit 0 6 0 64 Industrial 2 of 5 Enable Disable Industrial 2 of 5 Enable NW Disable Industrial 2 of 5 Check Digit Verification Enable Disable Industrial 2 of 5 Check Digit Transmission Transmit Industrial 2 of 5 Check Digit Do Not Transmit Industrial 2 of 5 Check Digit Industrial 2 of 5 Length Scan Max Code Length 2 Digits 00 99 99 Scan Min Code Length 2 Digits 00 99 1 66 Code ID setting j Scan Code ID 2 Digits 00 FF 6A Insert String 1 Selection Scan Insert String 1 1 Digit 0 6 0 Insert String 2 Selection Scan Insert String 2 1 Digit 0 6 0 67 Matrix 2 of 5 Enable Disable Matrix 2 of 5 Enable Disable Matrix 2 of 5 Check Digit Verification Enable Disable Matrix 2 of 5 Check Digit Transmission Transmit Matrix 2 of 5 Check Digit Do Not Transmit Matrix 2 of 5 Check Digit 68 Matrix 2 of 5 Length Scan Max Code Length 2 Digits 00 99 99 Scan Min Code Length 2 Digits 00 99 1 Code ID setting x Scan Code ID 2 Digits 00 FF 78 Insert String 1
9. Power off Interval Power Off Interval 2 Digits 00 99seconds 15seconds 4 Shut down the Scanner Immediately RF operating mode NO Store Mode Do not batch data The scanner attempts to transmit every scanned barcode If the transmission is failed the barcode data is ignored and issued a beep beep beep sound Auto store Mode The scanner starts storing barcode data when it loses its connection to a host for example when a user holding the scanner walks out of range Data transmission is triggered by reestablishing the connection with hsot for example when a user holding the scanner walks back into range 37 Auto Store Mode Start transfer Bar Code Data for Manual Transmission Mode Manual Transmission Mode Data transmission is triggered by scanning Manual Transmission Mode Start transfer Bar Code Data NO Store Mode Wire Less Communication Inter character delay Scan Wire Less Communication Inter character delay 2 Digits 0 0 9 9seconds 0 5seconds 38 EAN 13 and ISBN ISSN Enable Disable EAN 13 Enable EAN 13 Disable EAN 13 EAN 13 Check Digit Verification Enable EAN 13 Check Digit Verification Disable EAN 13 Check Digit Verification EAN 13 Check Digit Transmission Transmit EAN 13 Check Digit Do Not Transmit EAN 13 Check Digit 39
10. 100mm 200mm 300mm Omm 100mm 200mm 300mm 400mm 500mm 600mm 700mm 100 300mm 100mm gt Appendix 6 ASCII Table Table 3 Function Keys H P S2 keyboard USB RS 232 L 0 1 0 1 0 Null NUL DLE 1 Up Fl SOH DCI 2 Down F2 STX DC2 3 Left F3 ETX DC3 4 Right F4 EOT DC4 5 PgUp F5 ENQ NAK 6 PgDn F6 ACK SYN 7 F7 BEL ETB 8 Bs F8 BS CAN 9 Tab F9 HT EM A F10 LF SUB B Home Esc VT ESC C End F11 FF FS D Enter F12 CR GS E Insert Ctrl SO RS F Delete Alt SI US 101 Table 4 Chars DEL SP 0A ch ASCII Example 102 Appendix 8 Parameter bar code NO 0 UYD 2 WDD 4 IRINA A NN 6 WOW 8 IT TUT ATU NN 103 N1 1 MEEN HI 3 WD 5 WU 7 UTE UCT UU 9 UTE UCIT Ui A B C D E F Finish Setting 104
11. Selection Scan Insert String 1 1 Digit 0 6 0 Insert String 2 Selection Scan Insert String 2 1 Digit 0 6 0 69 Codabar Enable Disable Codabar Enable Disable Codabar Check Digit Verification Enable Disable Codabar Check Digit Transmission Transmit Codabar Check Digit Do Not Transmit Codabar Check Digit NHU 70 Start End type ABCD ABCD abcd abcd ABCD TN E abcd tn e Start End transmission Enable Disable 71 Codarbar Length Scan Max Code Length 2 Digits 00 99 99 Scan Min Code Length 2 Digits 00 99 1 Code ID setting k Scan Code ID 2 Digits 00 FF 6B Insert String 1 Selection Scan Insert String 1 1 Digit 0 6 0 Insert String 2 Selection Scan Insert String 2 1 Digit 0 6 0 72 Code 11 Enable Disable Code 11 Enable Disable Code 11 Check Digit Verification Enable 1bit check Digit Enable 2 bit check Digit Disable check Digit 73 Code 11 Check Digit Transmission Transmit Code11 Check Digit Do Not Transmit Code11 Check Digit Code 11 Length Scan Max Code Length 2 Digits 00 99 99 Scan Min Code Length 2 Digits 00 99 4 Code ID setting m Scan Cod
12. 0 6 0 58 Code 93 Enable Disable Code 93 Enable Disable Code 93 Check Digit Verification Enable Code 93 Check Digit Verification Disable Code 93 Check Digit Verification Code 93 Check Digit Transmission Transmit Code 93 Check Digit Do Not Transmit Code 93 Check Digit 59 Code 93 Full ASCII Conversion Enable Code 93 Full ASCII HEH Disable Code 93 Full ASCII Code 93 Length Scan Max Code Length 2 Digits 00 99 99 Scan Min Code Length 2 Digits 00 99 1 60 Code ID setting h Scan Code ID 2 Digits 00 FF 68 Insert String 1 Selection Scan Insert String 1 1 Digit 0 6 0 Insert String 2 Selection Scan Insert String 2 1 Digit 0 6 0 61 Interleaved 2 of 5 Interleaved 2 of 5 Data digits Variable Check digit one bit optional Enable Disable Format of Interleaved Enable NIR Disable Interleaved 2 of 5 Check Digit Verification Enable Disable 62 Interleaved 2 of 5 Check Digit Transmission Transmit Interleaved 2 of 5 Check Digit Do Not Transmit Interleaved 2 of 5 Check Digit Interleaved 2 of 5 Length Scan Max Code Length 2 Digits 00 99 99 Scan Min Code Length 2 Digits 00 99 1 63 Code ID setting
13. AK from the host an additional ENQ is not required ACK NCK with ENQ XON XOFF An XOFF character turns the scanner transmission off until the scanner receives an XON character There are two situations for XON XOFF XOFF is received before the scanner has data to send When the scanner has data to send it waits up to Host Serial Response Time out for an XON character before transmission Ifthe XON is not received within this time the scanner issues an error indication and discards the data XOFF is received during a transmission Data transmission then stops after sending the current byte When the scanner receives an XON character it sends the rest of the data message The scanner waits up to 30 seconds for the XON XON XOFF RTS Line State Host Low RTS Default Host High RTS amp RH 26 Host Serial Response Time out Data Bits 2 sec Default 5 sec 7 5 sec 10 sec 7 Bit 8 Bit Default 27 Stop Bit Select 1 Stop Bit Default 2 Stop Bit Parity None Default Odd Even Select Mark parity and the parity bit is always 1 Mart Select Space parity and the parity bit is always 0 Space 28 Inter character Delay This parameter specifies the inter character delay inserted between character 25mS 50mS 75mS 99mS transmissions 29 Global Sett
14. Barcode Scanner User s Manual Notice 1 Please carefully read the User Manual before using the barcode scanner All software including firmware furnished to the user is on a licensed basis The right is reserved to make changes to any software or product to improve reliability function or design The material in this manual is subject to change without notice Contents Scanning And Set Defaults ness nnnn Ynn Ynn nn nnnn Lennon 5 Programming Instruction 6 Programming without Parameter ii 6 Programming with Parameter 7 Interface selectionarea e iira aeiia 9 Scanning Mode Setting 10 Keyboardwedg amp T EE 12 USB interface EE 18 RS 232 Interface ine aa e aia i aaa 23 Global Settmge nnna apaa iaia 30 lao EELO TT 34 Wire Less Communication Setting en 35 EAN 13 and ISBN ISSN AY a HYAY RY LL RAI RH NHY E Hon 39 SE DEE 42 de 45 WI PG EE 48 e Ee 51 Code EE 55 Code 93 nii IG dedi EL Jo Un DR Y TYF JL DG dd 59 Interleaved 2 OF Bs rii ennu E eege eege Yn 62 Ind strial RE EE 65 Matrix 2 085 u EA es 68 Ree ELE 70 COGS E 73 MSI Plessey e A A ADN Ze 75 UK P esseyas Yu Li WY MUN MU ae ee en hi 78 GS1 DataBar GS1 DataBar Truncated i 81 GS1 DataBar Limited nn sera kannten nenn 83 GS1 DataBar Exvpanded iii 85 Advanced Bar Code Data Formatting i 86 Breet heat lo asa 87 SUPPL Mss iano hei ni nine ed eee ete ee Y Le 88 Pre
15. Press Scanning Mode 10 Click Scanning Mode When the button is click the scanner will keep scanning the barcode until the barcode is reader or the Stand by duration elapsed Click Scanning Mode Continuous Scanning mode the scan engine is always scanning and decoding The module will read the barcode which gets into the scanning area automatically Only when the barcode that has been read gets out of the scanning area the module can read the next barcode Select Continuous Scanning mode Auto Continue mode The scanner will start continuous scan Automatically if any object enter the scan area When there is no bar code is read for half a minute the scanner shutdown the laser line and exit continuous scanning mode Auto Continue mode 11 Keyboard wedge Keyboard type IBM AT PS 2 Other Reserved Keyboard layout USA Italian French Turkish F Turkish Q 12 Clock period According to the PS2 protocol the clock is provided by the device e g keyboard or scanner with the period between 60us to 200us 60 uS 80 uS 100 uS 200 uS 13 Delay after compound key In some rare occasions machine with low speed PS2 communication portwould require a free time gap following the press release of the compound key Shift Ctrl or Alt 0 mS W AA 10 mS TRL YA YA 20 mS RL INVII LUI 40 mS M BIYUDA A 80 mS TLL Numeric key Alphabetic
16. Scan Min Code Length Scan Min Code Length 2 Digits 00 99 1 Turn to the last page of this Manual Appendix 10 Parameter bar code scan the parameter bar code 0 and 5 0 WII HI 5 RI AH Scan Finish Setting finish the setting Finish Setting Interface selection This scanner supports interfaces such as keyboard wedge RS 232 serial wedge and USB interface Typically host is able to identify the host port type automatically In extreme cases host port may need setting manually if the host fails to identify it Automatic Identification USB PS 2 Key Board RS232 Scanning Mode Setting Good read off scanning Mode The trigger button must be pressed once to activate scanning The light source of scanner stops scanning when there is a successful reading or no code is decoded after the Stand by duration elapsed Select Good read off scanning Mode Auto detection scanning Mode The scanner will start scan Automatically if any object enter the scan area The laser light of scanner stops scanning when there is a successful reading or no code is decoded after the Stand by duration elapsed Once the laser light stops scanning the present object must be remove away from the scan area to enable Auto detect sensor Select Auto detection scan Press Scanning Mode It can continue scan barcode when the button is continuing pressed
17. ambl amp sa i ie EEN 88 Postamblenaua sea di Alan adr diy Y hihi 89 COGS DY NY NN Y eni RH ecg 90 CodeilD positiOns ud GG Td dT Lia 90 Code name transmission i 90 Code length transmission i 91 VEER ue LTE 91 Insert String G1 Setting iii 92 Insert String G2 Setting iene 92 Insert String G3 Setting edel lara licia 92 Insert String G4 Setting iii 93 ENT substitution string setting ii 93 Truncate leading G5 String setting iii 93 Truncate ending G6 string setting iii 94 Replace String Settinpi i iii aan ala 94 Test Bar Code E 95 Appendix 2 Default setting for each barcode 96 Appendix 4 Decode Zone eege iaia alal bilia 98 Appendix 6 ASCII Table ale 102 Appendix 8 Parameter bar code 103 Scanning When the scanner is scanning ensure the scan line crosses every bar and space of the bar code RIGHT RIGHT 012345 012345 WRONG WRONG 012345 012345 the Scan Line on the bar code Set Defaults And Information Display Set Factory Defaults If you wish to return the base unit to the entire factory default settings radio communication setting is not included scan the barcode Set Defaults Set Defaults Communication Information and Battery Power Display Wireless scanner Battery Power Display Communication Channel and ID Number or Scanner Display Programming i
18. e ID 2 Digits 00 FF 6D 74 Insert String 1 Selection Scan Insert String 1 1 Digit 0 6 0 Insert String 2 Selection Scan Insert String 2 1 Digit 0 6 0 MSI Plessey Enable Disable MSI Plessey Enable 0 Disable MSI Plessey Check Digit Verification Enable digit Mod10 Enable 2 digit Mod10 10 Enable 2 digit Mod11 10 Disable MSI Plessey Check Digit Transmission Transmit MSI Plessey Check Digit Do Not Transmit MSI Plessey Check Digit 76 MSI Plessey Length Scan Max Code Length 2 Digits 00 99 99 Scan Min Code Length 2 Digits 00 99 4 Code ID setting P Scan Code ID 2 Digits 00 FF 66 Insert String 1 Selection Scan Insert String 1 1 Digit 0 6 0 Insert String 2 Selection Scan Insert String 2 1 Digit 0 6 0 77 UK Plessey Check digit verification The UK Plessey has two optional check digits The check digit 1 and check digit 2 will be calculated as the sum module 10 or 11 of the data digits Enable Disable UK Plessey Enable Disable UK Plessey Check Digit Verification Enable Disable 78 UK Plessey Check Digit Transmission Transmit UK Plessey Check Digit Do Not Transmit UK Plessey Check Digit UK Plessy Lenght
19. gnore Unknown Characters Enable Disable Emulate Keypad Enable this to send all characters as ASCII sequences over the numeric keypad For example ASCII A transmits as ALT make 0 6 5 ALT Break Enable Disable Simulated Caps Lock Enable this to invert the upper and lower case characters on the scanned bar code as if the Caps Lock state is enabled on the keyboard This inversion occurs regardless of the keyboard s Caps Lock state Enable Disable 21 USB Keyboard FN 1 Substitution This option applies only to the USB HID Keyboard Emulation device When enabled this allows replacing any FN 1 characters in an EAN 128 bar code with a Key Category and value chosen by the user Enable Disable 22 RS 232 Interface Baud Rate 2400 4800 9600 19200 38400 57600 23 Handshaking None Scan the bar code below if no Hardware Handshaking is desired None Default Standard RTS CTS Scan the bar code below to select Standard RTS CTS Standard RTS CTS Hardware Handshaking RTS CTS Option 1 When RTS CTS Option 1 is selected the scanner asserts RTS before transmitting and ignores the state of CTS The scanner de asserts RTS when the transmission is complete RTS CTS Option 1 RTS CTS Option 2 When Option 2 is selected RTS is always high or low user programmed logic level However the scanner waits for CTS to be a
20. ings Element amendment Enable Element amendment Disable Element amendment Printable character Output only Enable Disable Decoder optimization Enable Decoder optimization Disable Decoder optimization 30 Save Power Enable Disable Standby duration 2 second 5 second 10 second 20 second 31 Double confirm Disable Double confirm 2 Times 5 Times 10 Times Same barcode delay time If a barcode has been scanned and output once successfully the laser beam must be off or moved away from the barcode beyond delay time to active scanning the same barcode When this feature is set to be 0xFF then the delay time is indefinite Same barcode delay time 2 Digits 00 99 00 32 Global Max Min code length Global Max code length 2 Digits 00 99 99 Global Min code length 2 Digits 00 99 XX Global G1 G6 string selection Global Insert String 1 1 Digits 0 6 0 Global Insert String 2 1 Digits 0 6 0 Decode UPC EAN Only With Supplementals Enable Disable 33 Indication Volume of beeper Beep tone High Middle Low Mute High Tone Middle Tone Low Tone 34 O Wire Less Communication Setting Unpair the scanner from ho
21. key Numeric keypad N D a i I N Alt keypad 14 Power on simulation All of the PCs check the keyboard status during power on self test It simulates keyboard timing and passes keyboard present status to the PC during power on Enable Disable Inter character delay This delay is inserted after each data character transmitted 0 mS 5 mS 10 mS 20 mS 15 40 mS 80 mS Inter byte delay This delay is inserted after each byte transmitted Normally a character is comprised of three or above bytes 1 mS 2 mS 4 mS 8 mS 16 Caps Lock reversion By setting enable the status of Caps Lock key i e being pressed ON or OFF on the keyboard is simulated in a reversion status Enable Caps Lock Disable Caps Lock Caps Lock override If this function is enabled on AT or AT notebook hosts the keyboard ignores the state of the Caps Lock key Therefore an A in the bar code is sent as an A no matter what the state of the keyboard s Caps Lock key Enable Disable 17 USB interface USB device type HID Keyboard HIR Virtual RS232 Port reserved DW IBM Table Top USB HIRT IBM Hand Held USB DH USB OPOS Hand Held 18 USB Keyboard layout USA German French Other USB Keystroke Delay No Delay 20mS 40mS 19 USB CAPS Lock Override Enable Disable USB I
22. nstruction The scanner is programmed by scanning the setting barcode in the Manual There are two kinds of Programming instructions One of them programmed with Parameter and the other one of them without Parameter Programming without Parameter When programming without parameter only one setting barcode is need to be scanned For example shut down the beeper of the scanner just scan the bar code directly When it is programmed successful the scanner issue a beep beep sound but issue a beep beep beep sounds when programmed fails Mute NOTE the factory default settings are indicated with asterisks Programming with Parameter It is need to scan more than one setting barcode to program the scanner with parameter Default parameters Range of parameters length of parameters Setting Barcode Program Parameters The steps of programming are 1 Scan the Function Setting Barcode The Scanner will issue a beep sound and the Red LED is on until the program is finished 2 Scan the parameters bar code The parameters may be one or more than one digits 3 Scan the setting barcode Finish Setting If it is programmed successful the scanner will issue a beep beep sound but issue a beep beep beep sound when fails e g Set min code length of Code 128 to 5 chars Open the manual and turn chapter code128 Scan the setting bar code
23. sition of G3 2 Digits 00 99 00 Insert String G4 Setting G4 is also used as the string to replace G3 in a bar code data when the replace function is enabled Scan Inert String G4 0 16 Chars 2 Digits Char 00 FF 00 92 Scan the Position of G4 2 Digits 00 99 00 FN1 substitution string setting The ENT character 0x1D in an UCC EAN128 barcode or a Code 128 barcode or a GS1 DataBar barcode can be substituted with a defined string Enable FN1 Substitution Disable FN1 Substitution Scan FNI substitution string setting 0 4 Chars 2 Digits Char 00 FF Truncate leading G5 String setting By setting G5 a defined leading character or string can be truncated G5 can 00 also be set to be repeated Scan G5 String 0 16 Chars 2 Digits Char 00 FF 00 93 Truncate leading G5 string setting 2 Digits 00 99 01 Truncate ending G6 string setting By setting G6 a defined ending character or string can be truncated G5 can also be set to be repeated Scan G6 String 0 16 Chars 2 Digits Char 00 FF 00 Scan Repeat of a G6 String 2 Digits 00 99 01 Replace String Setting Replace G3 string to G4 string in barcode data Enable 94 Disable Test Bar Code 00012345000 1234567890 95 6 32501
24. sserted before transmitting data If CTS is not asserted within Host Serial Response Time out the scanner issues an error indication and discards the data RTS CTS Option 2 24 RTS CTS Option 3 When Option 3 is selected the scanner asserts RTS prior to any data transmission regardless of the state of CTS The scanner waits up to Host Serial Response Time out for CTS to be asserted If CTS is not asserted during this time the scanner issues an error indication and discards the data The scanner de asserts RTS when transmission is complete RTS CTS Option 3 ACK NAK When this option is selected after transmitting data the scanner expects either an ACK or NAK response from the host When a NAK is received the scanner transmits the same data again and waits for either an ACK or NAK After three unsuccessful attempts to send data when NAKs are received the scanner issues an error indication and discards the data ACK NCK ENQ When this option is selected the scanner waits for an ENQ character from the host before transmitting data If an ENQ is not received within the Host Serial Response Time out the scanner issues an error indication and discards the data The host must transmit an ENQ character at least every Host Serial Response Time out to prevent transmission errors ENQ IR III INN 25 ACK NAK with ENQ This combines the two previous options For re transmissions of data due to a N
25. st Unpair the scanner from host Pair Scanner with Host Pairing is the process by which a scanner initiates communication with a host The scanner with the Host pairing as follows 1 Connect the scanner to the Host with the Charging Cable 2 Press the Pairing Button until the Scanner issued a beep beep sound NOTE A host is able to work with as more as 99 scanners at the same time Clear the Buffer of Scanner Scan the setting bar code below will clear the bar code data save in the scanner buffer Clear the Buffer of Scanner 35 Wire Less Channel When there are more than one host work in the same Space every host has to work in different channel Channel is set as follows 1 Open a Notepad or other text editor 2 Press the Channel Settings button to change the channel of a host and the channel NO will be displayed in the screen Scanner ID Set the Scanner ID 2 Digits 00 99 00 Add Scanner ID as Prefix If this item is enabled the scanner will add its ID as prefix of every barcode E g When scan the bar code 12345 if the ID of the scanner is 15 and the output barcode data will be ID1512345 NOTE The ID of a scanner can be set manually or assigned by the host automatically Every scanner work with the same Host can t be with the same ID Enable Add Scanner ID as Prefix Disable Add Scanner ID as Prefix 36
26. tring 1 Selection Scan Insert String 1 1 Digit 0 6 0 Insert String 2 Selection Scan Insert String 2 1 Digit 0 6 0 84 GS1 DataBar Expanded Enable Disable GS1 DataBar Expanded Enable Disable Conversion Convert GS1 DataBar Expanded UCC EAN 128 Disable Conversion GS1 DataBar Expanded Lenght Scan Max Code Length 2 Digits 00 99 99 Scan Min Code Length 2 Digits 00 99 1 Code ID setting p Scan Code ID 2 Digits 00 FF 70 Insert String 1 Selection Scan Insert String 1 1 Digit 0 6 0 Insert String 2 Selection Scan Insert String 2 1 Digit 0 6 0 Advanced Bar Code Data Formatting Format of barcode data transmission Prefix Code Preamble Code Code Code Code Postamble Suffix 86 name ID length data Suffix Quick Setup Prefix CR LO LF CR amp LF None 87 Transmit Prefix Do Not Transmit Prefix Scan Prefix 0 16 Chars 2 Digits Char 00 FF 00 NW Suffix The default Suffix is CR Transmit Suffix Do Not Transmit Suffix Scan Suffix 0 22 Chars 2 Digits Char 00 FF 00 Preamble Transmit Preamble Do Not Transmit Preamble 88
Download Pdf Manuals
Related Search