UB-E01 User`s Manual CAUTION:
Contents
1. 10BASE T Ethernet LED green LED red Switch Display module connector interface i connector Be sure not fo push the If you press and hold The display module LEDs by accident this switch when the connector on the TM printer printer is on the cannot be used when the interface will be UB E01 is installed reset to the factory settings Note This photograph shows the TM H6000 printer with the UB E01 installed Connecting the Cables Before connecting any of the cables make sure that both the printer and the host computer are turned off Connecting the 1OBASE T Ethernet cable 1 Make sure both the printer and the host computer are turned off 2 Plug the 10BASE T cable connector securely into the UB E01 s 1OBASE T Ethernet connector until you feel it click CAUTION Do not connect a telephone line a display module cable or a drawer kick out cable to the UB EOQ1 s IOBASE T connector Q Note The display module connector on the TM printer cannot be used when the UB E01 is installed 3 Connect the power supply to the printer EMC Standard Applied Product Name UB E01 Model Name M155A The following standards are applied only to the interface boards that are so labeled EMC is tested using the EPSON PS 170 power supply and TM series printers Europe CE markin North America EMI FCC ICES 003 Class A Japan EMC VCCI Class A Oceania EMC AS NZS 3548 Class B W2. A CAUTION Connecting an outdoor overhead LAN cable directly to your product Connecting an outdoor overhead LAN cable directly to your product may lead to lightning damage If you need to connect such a cable to your product the cable must be protected against an electrical surge between the cable and your product You should avoid connecting your product to a non surge protected outdoor overhead LAN cable
3. UB E01 User s Manual Copyright 1999 SEIKO EPSON CORPORATION 401209601 Introduction The UB E01 designed for EPSON TM printers is a 1OBASE T Ethernet interface board This manual provides instructions for operators of POS systems in which the UB E01 is installed so that the operators can use the UB E01 safely and correctly For information about installation and settings required see the UB E01 Developer s Guide To get the UB EO Developer s Guide contact your EPSON representative or your place of purchase Key fo Symbols The symbols in this manual are identified by their level of importance as defined below Read the following carefully before handling the product N CAUTION Observe cautions to avoid minor injury to yourself damage to your equipment or loss of data Q Note Notes have important information and useful tips on the operation of your equipment Caution Label The following caution label is visible near the display module connector A The label has the following meaning The display module connector and the drawer kick out connector use the same type of the Ethernet connector therefore be sure not to connect the Ethernet connector cable or the telephone line to the display module connector or the drawer kick out connector Part Names The following view shows the part names of the UB E01 gt Power supply connector Drawer kick out connector
4. ARNING The connection of a non shielded interface cable to this board will invalidate the EMC standards of this device You are cautioned that changes or modifications not expressly approved by SEIKO EPSON Corporation could void your authority to operate the equipment CE Marking The printer conforms to the following Directives and Norms Directive 89 336 EEC EN 55022 Class B EN 55024 IEC 61000 4 2 IEC 61000 4 3 IEC 61000 4 4 TEC 61000 4 5 IEC 61000 4 6 TEC 61000 4 11 The printers in which this board is installed do not conform to the following Directive 90 384 EEC EN 45501 FCC Compliance Statement For American Users This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequeney energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense For Canadian Users This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme la norme NMB 003 du Canada
Download Pdf Manuals
Related Search