AltaDyne™ Plus
Contents
1. N CAUTION Indicates a potential hazard or unsafe practice that if not avoided could result in minor or moderate personal injury A NOTICE Indicates a potential hazard or unsafe practice that if not avoided could result in product or property damage Info Provides application recommendations or other useful information to ensure that you get the most from your product DANGER To reduce the risk of electrocution N DANGER Always unplug this product immediately after use N DANGER Do not use this product while bathing N DANGER Do not place or store this product where it can fall or be pulled into a tub or sink N DANGER Do not place this product in or drop into water or other liquid N DANGER Do not reach for a product that has fallen into water Unplug it immediately 4 760000 INS LAB RevD1 1 WARNING To reduce the risk of burns electrocution fire or personal injury WARNING Do not leave this product unattended when plugged in Z WARNING Always use close supervision when this product is used by on or near children or those who require close supervision WARNING Use this product only as intended and described in this manual Do not use attachments or accessories not recommended by Graham Field Z WARNING Never operate this product if a It has a damaged cord or plug b It is not working properly c It has been dropped or damaged d It has been dropped into water Return t2. Cycle Time buttons and selecting the desired settings The selected indicators will illuminate during Autofirm and the system will automatically operate your settings immediately after the Autofirm process is complete When the selected pressure level is reached the low pressure indicator yellow LED and the Autofirm indicator will de illuminate and the pump will enter alternating mode If not preset as described in step 4 the mattress can now be adjusted to the desired pressure Replace all sheets blankets and pillows on the bed 760000 INS LAB RevD11 13 PRESSURE ADJUSTMENT Generally a lighter patient will need a lower softer setting while a heavier patient will need a higher firmer setting but pressure adjustment must ultimately be based on the patient s weight distribution A short stocky person may be the same weight as a tall thin person but their settings will not be the same The mattress should be firm enough to support the patient yet soft enough so the patient will sink down to eliminate pressure points Initially inflate the mattress to maximum pressure Then when patient lies on the mattress test the pressure by placing four fingers below the mattress under the patient s buttock area your fingers should just fit If the fit is too loose decrease the setting If your fingers do not fit well increase the setting two notches firmer Wait ten minutes and then check again You should only have to adjust this s
3. E 1 Check main power cord for abrasion or excessive wear 2 Check mattress cover for signs of wear or damage Ensure mattress cover and tubes are connected correctly 3 Check airflow from the air hose connector The airflow should alternate between each connector every half cycle time if it s in alternating mode 4 Check the air hoses for any kink or break For replacement please contact your GF equipment provider 16 760000 INS LAB RevD11 Fuse replacement If you suspect a blown fuse tool needed small screwdriver disconnect the plug from the wall outlet immediately Use a small screwdriver to remove the cover of the fuse holder fuse locations are shown in picture at right Insert a new fuse of the correct rating T1A 250V VDE approved Replace the fuse holder cover Ensure that fuse holder cover is securely installed Air filter replacement tool needed small screwdriver 1 Use a small screwdriver to remove the air filter plate located at rear of pump filter location is shown in picture at right 2 Remove the filter The filter is reusable if not torn and can be washed gently with a mild detergent and water Dry the filter before use 3 Replace the filter and cover Ensure that filter cover is securely installed Replace the air filter regularly if it is gray torn or the environment is dirty STORAGE 1 Lay the mattress out flat and upside down 2 Roll from the head end to
4. ESS INSTALLATION 11 OPERATION nesenie 13 PRESSURE ADJUSTMENT eere nnnm enne innu 14 QUICK DISCONNECGCT aocci tin anta da airo r 14 TRANSPORT CAP eeeeeeeee seen nennen enn snnm snnt annee na nnn aan nn san enn 14 CPR FUNCTION snis nnn 15 MAINTENANCE c 16 unl c X 16 GENERAL MAINTENANTCE eene nennen 16 FUSE REPLACEMENT ph bara cgi aV ad Va 17 AIR FILTER REPLACEMENT 17 STORAGE 17 SPECIFIGCAT IONS 22 2 24422 2 56 0 2a82 6c ck sanc coxa d dans iE c tid dnas 18 WARRANTY f 19 Graham Field Lumex and AltaDyne are registered trademarks of GF Health Products Inc GF Health Products Inc Graham Field is not responsible for typographical errors Packaging warranties specifications and products are subject to change without notice 2 760000 INS LAB RevD1 1 INTRODUCTION Use this manual for set up and operation of the Lumex AltaDyne Plus 760000 Alternating Pressure Low Air Loss Mattress System Read all in
5. LLIIVIEX A Graham Field Brand AltaDyne Plus 760000 ALTERNATING PRESSURE LOW AIR LOSS MATTRESS SYSTEM Info The most current version of this manual can be found online at www grahamfield com 760000 INS LAB RevD11 5 INTRODUCTION mm snanmmnnnnnemmnnannennnnnnmnennnnnmnnnnnnee 3 INTENDED USE OF THIS DEVICE eere 3 nnne nnne nnne nnne nnne 3 IMPORTANT SAFETY PRECAUTIONS eres 4 DANGER P 4 ll cm 5 ere 6 EQUIPMENT SYMBOLS eerie enne enne nnns 7 PRODUCT DESCRIPTION eese eene nnns 8 PUMP AND MATTRESS SYSTEM eere nnns 8 PUMP FRONT aae 8 PUMP REAR UE 8 PUMP FRONT PANEL adesa cn scan aandaa iaa 9 FRONT PANEL FIRST ROW CYCLE TIME ADJUSTMEN 9 FRONT PANEL SECOND ROW PRESSURE ADJUSTMENT 9 FRONT PANEL THIRD ROW THERAPY MODE ADJUSTMENT 9 FRONT PANEL FOURTH 10 INSTALLATION nrrnnnnnemnnnnnnmmnennnnnennnennnnnnnnennnnnennnnnnnn ee 11 11 PUMP AND MATTR
6. anger power cord receptacle filter 8 760000 INS LAB RevD11 PUMP FRONT PANEL cycle time adjust button cycle time decrease pressure button indicators at right of button pressure level indicators at right of button increase pressure button therapy adjust button AUN therapy mode indicators at right of button am panel lock button panel lock AX indicator at right of button ns service indicator low pressure indicator upper power ON OFF button ON OFF power failure indicator lower indicator at right of button alarm mute button Front panel first row cycle time adjustment There are four cycle time settings Press the cycle time adjust button to cycle between the settings The selected cycle time setting s indicator will illuminate Front panel second row pressure adjustment There are ten pressure firmness settings Press the decrease pressure button at the left end of the row to decrease pressure softer and press the increase pressure button at the right end of the row to increase pressure firmer The selected pressure level setting s indicator will illuminate Front panel third row therapy mode adjustment There are four therapy mode settings Autofirm to fill mattress quickly or to fully inflate mattress during patient ingress egress for better support Alternating Pressure every other tube fills then deflates Static all tubes remain full and Seat Inflati
7. cessary contact your Graham Field equipment provider to replace any damaged tubes or hoses 3 If problem persists contact your Graham Field equipment provider Power failure indicator The power failure indicator illuminates and the alarm sounds when there is a power failure Depress the alarm mute button to disable both alarm and LED Service indicator Mechanical failure service required contact your Graham field equipment provider 10 760000 INS LAB RevD11 INSTALLATION UNPACKING 1 Before unpacking check for obvious damage to the carton or its contents If damage is evident please notify the carrier and your Graham Field equipment provider Remove all loose packing from the carton Carefully remove all components from the carton Inspect all components If damage is evident please notify the carrier and your Graham Field equipment provider PUMP AND MATTRESS INSTALLATION 1 Either hang the pump on the Place the mattress on top of the bed frame ensure that the foot end symbol faces up at foot end as shown at right Secure mattress to bed with straps am Fold open the wire hangers on the back of the pump as shown at right bed s foot end as shown at right or place the pump ona flat surface easily accessible to the caregiver and or doctor NOTICE Place the device in a position where the caregiver and or doctor can access it easily Connect the mattress pump air hose quick conn
8. ector ensure that the connector has clicked securely into place before continuing 760000 INS LAB RevD11 11 A NOTICE Ensure that the air hoses are not kinked or tucked under the mattress Z WARNING Locate all cords so that they will not be stepped on tripped over or otherwise subjected to damage or stress A WARNING Do not use a household extension cord if the electrical cord does not reach the power outlet Use of an improper extension cord could result in fire and electric shock If an extension cord must be used use a three conductor cord with ground properly wired in good electrical condition and keep it as short as possible A WARNING Ensure that the local power voltage is appropriate for the pump unit 5 Plug the power cord into a properly grounded electrical outlet 12 760000 INS LAB RevD1 1 Turn the main power switch OPERATION to the ON position power switch Press the front panel power button The power indicator will illuminate power button Info The mattress system will automatically enter Autofirm mode for the quickest inflation at set up initial inflation takes approximately twenty minutes 3 The pump will begin delivering air into the mattress The low pressure indicator yellow LED and the Autofirm indicator will illuminate until the mattress is fully inflated During Autofirm you can preset the device by pressing the Therapy Comfort and
9. etting one time per patient Please consult your physician for an appropriate setting QUICK DISCONNECT Pull the power plug from the wall connector to disconnect the device quickly TRANSPORT CAP In case of power failure or transport Disconnect the quick connector and cap the mattress with the transport cap to slow deflation RTT connector 14 760000 INS LAB RevD11 CPR FUNCTION If CPR must be performed on the patient while the mattress is in use to immediately deflate the mattress either 1 Pull the CPR valves from the mattress in the location of the arrow shown at right or 17 2 Disconnect quick connector o from the pump in the location of the arrow shown at right 760000 INS LAB RevD11 15 MAINTENANCE CLEANING Perform the following cleaning procedures before use Pump Wipe the pump with a clean damp cloth and mild detergent and keep it away from dust Air dry A NOTICE Do not use phenolic products or corrosive or powdered cleansers to clean the pump A NOTICE Do not immerse or soak the pump Mattress Wipe the mattress unit with a clean damp cloth and mild detergent The mattress may also be cleaned using a 10 solution of sodium hypochlorite bleach diluted in water Air dry all parts thoroughly before use A NOTICE Do not use phenolic products to clean the mattress A NOTICE After cleaning air dry the mattress without direct exposure to sunlight GENERAL MAINTENANC
10. he product to your Graham Field equipment provider Z WARNING Keep the cord away from heated surfaces N WARNING Never block the air openings of this product or place it on a soft surface such as a bed or couch where the openings may be blocked Keep the air opening free of lint hair and other similar particles Z WARNING Never drop or insert any object into any opening or hose N WARNING Connect this product only to a properly grounded power outlet WARNING Maximum patient weight capacity for this product is 400 Ib 189 kg 760000 INS LAB RevD11 5 WARNING Patient entrapment with bed side rails may cause injury or death The bed frame and its components including the mattress bed side rails head and foot board bedding and any accessories added to the bed can all affect the risk of entrapment Thorough patient assessment and monitoring are necessary to reduce the risk of entrapment including establishing whether the use of a bed rail is in the best interest of the patient Read and understand the User Manual before using this equipment GF Health Products Inc product manuals are available online at www grahamfield com Visit the FDA s Bed Safety page at www fda gov to learn more about the risks of entrapment It is the responsibility of the facility and provider to be in compliance with these guidelines Refer to user manuals for beds and rails for additional product safety information After any ad
11. justment repair or service and before use ensure all attaching hardware is securely tightened Bed rails with dimensions different than the original equipment specified by the bed manufacturer may not be interchangeable and may result in entrapment or other injury NOTICE A NOTICE The pump can be used only with the accompanying mattress Do not use it for any other purpose 6 760000 INS LAB RevD11 EQUIPMENT SYMBOLS ZN Attention Consult accompanying documents this manual BF symbol Indicates that this product is in accordance with the degree of protection against electric shock for type BF equipment _ Functional earth for UL only Class Il for UL only please consult your local city office household waste disposal Disposal of Electrical amp Electronic Equipment WEEE Do not treat this product as household waste For more detailed information with regard to returning and recycling this product service or Graham Field equipment provider For U S and Canada only Medical Equipment Air Pump E228589 S o with respect to electrical shock fire and 53DG mechanical hazards only in accordance with UL60601 1 and CAN CSA C22 2 No 601 1 760000 INS LAB RevD1 1 7 PRODUCT DESCRIPTION PUMP AND MATTRESS SYSTEM foot end symbol M valves mM mattress pump connectors mattress pump and mattress system PUMP FRONT quick connector PUMP REAR main power switch A 2 h
12. on when the head is raised to increase pressure under the buttocks Press the therapy adjust button at the left end of the row to cycle between the settings The selected therapy mode setting s indicator will illuminate 760000 INS LAB RevD11 9 Front panel fourth row Panel lock button The panel lock protects the panel settings from accidental change Press for two seconds to lock press for two seconds to unlock When the panel is locked the panel lock indicator will illuminate Power button ON OFF The power button turns power to the mattress system ON or OFF Press to turn ON press to turn OFF When power is on the power ON OFF indicator will illuminate When power is turned OFF mattress system will slowly deflate Info Main power switch on side of pump must be ON in order for the panel power button to function Alarm mute button The alarm mute button temporarily suspends the LED indicator and buzzer when either the low pressure alarm or power failure alarm is activated Should the problem not be resolved within five minutes the alarm will resume Low pressure indicator The low pressure indicator illuminates and the alarm sounds when the pressure level is lower than the selected pressure If the low pressure indicator persistently illuminates inappropriately 1 Check to ensure all connections are properly and securely connected per installation instructions 2 Check for any leakage tubes or connecting hoses If ne
13. structions before using the mattress system Save this manual for future reference INTENDED USE OF THIS DEVICE The intended use of the Lumex AltaDyne Plus 760000 Alternating Pressure Low Air Loss Mattress System is e The treatment of pressure ulcers while optimizing user comfort e Pain management as prescribed by a physician e As described above in either a homecare or long term care setting Contraindication Z WARNING DO NOT use this product in the presence of flammable anesthesia There is a possible fire hazard when this product is used with certain oxygen delivery equipment Use nasal cannula face mask or 1 2 length oxygen tent to deliver oxygen in the presence of this product DO NOT use a full length oxygen tent that extends past the top surface of the mattress with this product 760000 INS LAB RevD11 3 IMPORTANT SAFETY PRECAUTIONS The safety statements presented in this chapter refer to the basic safety information that should be observed by those using the Alternating Pressure Low Air Loss Mattress System There are additional safety statements in other chapters or sections which may be the same as or similar to the following or specific to the operations Z DANGER Indicates an imminent hazard situation that if not avoided will result in death or serious injury N WARNING Indicates a potential hazard situation or unsafe practice that if not avoided could result in death or serious injury
14. urred in replacement part s installation or any associated freight or shipping charges to GF Health Products Inc The warranties contained herein contain all the representations and warranties with respect to the subject matter of this document and supersede all prior negotiations agreements and understandings with respect thereto The recipient of this document hereby acknowledges and represents that it has not relied on any representation assertion guarantee warranty collateral contract or other assurance except those set out in this document 760000 INS LAB RevD11 19 USA Corporate Headquarters GF Health Products Inc 2935 Northeast Parkway Atlanta Georgia 30360 telephone 770 368 4700 fax 770 368 2386 GRAHAM FIELD www grahamfield com 2011 GF Health Products Inc
15. ward the foot end 3 Stretch the foot end strap around the rolled mattress to prevent unrolling 4 Store mattress and pump in a dust free environment with no exposure to direct sunlight A NOTICE Do not fold crease or stack the mattress 760000 INS LAB RevD11 17 SPECIFICATIONS Pump Specification Info see rating label on product Arint _ _ Environment Temperature Operation 50 F to 104 F 10 C to 40 C Storage 5 F to 122 F 15 C to 50 Shipping 5 F to 158 F 15 C to 70 Humidity Operation 10 to 90 non condensing Storage 10 to 90 non condensing Shipping 10 to 90 non condensing Classification Class Il Type BF IPX0 Applied Part Air Mattress Not suitable for use in the presence of a flammable anesthetic mixture No AP or APG protection Sedi O Model Bt mattress 78 7 x 35 4 x 8 200 x 90 x 20 3 cm Weight 18 760000 INS LAB RevD11 WARRANTY GF Health Products Inc warrants the Lumex AltaDyne Plus 760000 Alternating Pressure Low Air Loss Mattress System for a period of twelve months for defects in workmanship and materials If a product is deemed to be under warranty GF Health Products Inc shall provide at its option 1 replacement of any defective part or product or 2 a credit of the original selling price made to GF Health Products Inc s initial customer The warranty does not include any labor charges inc
Download Pdf Manuals
Related Search