Wireless Keypads
Contents
1. LED 1 LED 4 LED 2 mE LED 3 LED 1 indicator system armed On Total set is being armed Flashing slowly Partial set is being armed Flashing quickly Annex set is being armed Off The system is disarmed LED 2 indicator system fault On A system fault is occurring on set System faults include battery or power failure supervision fault GSM GPRS failure or radio Jamming Please contact your alarm company if this indication persists Flashing slowly A system fault is in memory on set and requires a reset Off No system fault LED 3 indicator tamper alarm On A tamper alarm is occurring on set Flashing slowly A tamper alarm is in memory on set and requires a reset Off No tamper alarm LED 4 indicator intruder alarm On An intruder alarm is occurring or a detector is triggered on set This includes open door contact movement detection or smoke detection Flashing slowly An intruder alarm is in memory on set and requires a reset Flashing quickly A confirmed alarm is in memory and requires a remote reset Please call your monitoring operation at the alarm company Off No intruder alarm Keypad tones Sequence of 3 modulated sounds When arming total set TOTAL SET confirms that the contr2. BATTERIES BY COMPLYING WITH APPLICABLE NATIONAL AND LOCAL REGULATIONS IN THE EVENT OF THE BATTERY BEING DAMAGED USE PERSONAL PROTECTIVE EQUIPMENT TO REMOVE IT IMMEDIATELY AND DISPOSE OF IT IN A SAFE MANNER REFER TO THE BATTERY MANUFACTURER S SPECIFICATIONS FOR SUCH SITUATIONS FOR SWITZERLAND ANNEX 4 10 OF SR 814 013 APPLIES TO THE BATTERY INCLUDED WITH THIS PRODUCT THERE IS A RISK OF EXPLOSION IF THE CORRECT BATTERY IS NOT USED REPLACE ONLY WITH LITHIUM BATTERY TYPE CR123A Please contact your local authorized Honeywell representative for product warranty information All data and images in this document are subject to change without prior notice Honeywell Security Honeywell Security amp Communications 1198 Avenue du Docteur Maurice Donat BP 1219 06254 MOUGINS CEDEX Tel 33 0 4 92 94 29 50 Fax 33 0 4 92 94 29 60 www honeywell com 2010 Honeywell International Inc Honeywell Honeywell is a registered trademark of Honeywell International Inc All other trademarks are the properties of their respective owners All right reserved 13 2010 Honeywell International Inc Honeywell Honeywell is a registered trademark of Honeywell International Inc All other trademarks are the properties of their respective owners All right reserved 800 07723 Rev A1
3. system will disarm as normal but a silent alert signal is transmitted to your alarm company Audio Verification Optional Audio verification is the feature thereby your central monitoring station establishes an audio communication with the protected area to verify the premises in the event of an intrusion It is especially used to validate an intrusion or lift doubts with the owner in case of a false alarm The audio communication can only be initiated by the operator located in the monitoring station after an alarm has been triggered The audio communication can be configured alternatively in Listening mode operator listen to the protected area and persons located in the protected area can talk to the operator In listening mode all LEDs light up at the same time Talking mode operator talks to the people located in the protected area It is important to note that in this mode the operator will not hear any sounds coming from the protected area Users must wait for the operator to switch to listening mode before talking In talking mode LEDs turn off or go back to displaying the system status Note For EN panels all LEDs flash in talking and listening mode when the system is armed The keypad is equipped with a microphone and a loud speaker with increased range capabilities which allows you to communicate without standing next to the keypad For installation with multiple wireless audio keypads audio communication ca
4. 000000 if 6 digits A double beep is played and all LEDs light To disable a user 1 Press and hold user number 0 to 9 key for 3 seconds Note it is not possible to disable the master user A double beep is played and LEDs all light 2 Enter the master code or present a tag All LEDs start flashing 3 Press the key to disable the user The programming mode ends automatically All LEDs stop flashing and a high beep is played To enable a user 1 Press and hold the user number 0 to 9 key for 3 seconds A double beep is played and all light 2 Enter the master code or present a tag All LED start flashing 3 Press the key to enable the user The programming mode ends automatically All LEDs stop flashing and a high beep 2 is played Master User Programming Mode Summary Procedure Entering prog Authorization Selection End User key 0 9 Master code or Assign TAG for 3 sec master TAG Present TAG Changing User key 0 9 Master code or Code for 3 sec master TAG New user s code New user s code Disabling User key 0 9 Master code or 0000 0000 Code for 3 sec master TAG or 000000 or 000000 User key 0 9 Master code or FAT Enable Heer for 3 sec master TAG A User key 0 9 Master code or foi for 3 sec master TAG B Indicator lights The front cover of the keypad features LED indicators which show the status of your security system EN
5. Wireless Keypads LKP E S8M Series User manual Honeywell Contents Congratulations on your purchase of this Honeywell wireless keypad To make the best out of your equipment we advise you to read this manual carefully This keypad is designed to operate on an authorised radio frequency and will in no way endanger the user INTFODUCTION a 2 Arming using your code or 3 Arming with fault GPBRERBRRPEPERBPRPEPEREPEPEPEFEREPEREEEEEPEHEEEEEPEREEEEEPEREEERERE 3 Disarming using your code or tag 4 Resetting the system after an alarm 4 Incorrect code protection eere 5 Personal attack i careret ena Cin vaa 5 D tess Code anne 5 Audio 5 User programming 6 Indicator ghis 10 Keypad TONGS ius 11 Maintenance and Recommendations 12 Introduction This manual describes how to use your wireless keypad The keypad is used to arm and disarm your security system using a valid access code or a key TAG The keypad is equipped with a proximity tag reader located next to the 8 nume
6. de and save you changes A double beep is played and all LED stop flashing To enable disable chime 5 Press and hold the and 13 keys simultaneously more than 3 seconds to enter user programming mode 6 Press the key All LEDs will start flashing and a long beep is played 7 Press the key to enable the chime or the key to disable the chime A long beep is played 8 Press the B key to exit user programming code and save you changes A double beep is played and all LED stop flashing To associate a TAG to a user 1 Press and hold the user number 0 to 9 key for 3 seconds 1 is the master A double beep is played and all LED light 2 Enter the master code or present a tag All LEDs start flashing 3 Present a TAG The programming mode ends automatically All LEDs stop flashing and a low beep is played The operation fails if the TAG is already registered If the user already has a TAG the new one will take its place To change a user s code 1 Press and hold the user number 0 to 9 key for 3 seconds 1 is the master A double beep is played and all LEDs light 2 Enter the master code or present the master tag All LEDs start flashing 3 Enter the code for the new user 4 Re enter new user s code The programming mode ends automatically All LEDs stop flashing and a high beep is played To disable a user s code To disable a user s code and keep the TAG only 1 Change the code to 0000 or
7. n only be activated on one device at a time It is possible to switch the audio communication at any time to any keypads by pressing anyone of the keys of the keypad A beep is played to the operator on the phone to indicate the switch User Programming functions Important The system will automatically exit the programming mode after 20 seconds if no keys are pressed during this time When this happens you must repeat all of the steps necessary for the function you are using The keypad features 2 programming modes User Programming mode to adjust beep level or enable disable the chime Master User Programming mode to manage user profiles The keypad can have up to 10 user profiles configured This mode can only be accessed with the master code master user 1 To adjust the volume of the beep 1 Press and hold the and 3 keys simultaneously more than 3 seconds to enter user programming mode A double beep is played and all LED light up 2 Keep pressing the key to select the device that you wish to adjust each device will emit a beep when it is selected RAM n want to adjust the beep level for device 2 press the its selection All LEDs start flashing 3 Press a key from to to select the required beep volume 1 min 7 max The device selected will emit a beep to confirm the beep volume key twice Device 2 will emit a beep to confirm 4 Press the key to exit user programming co
8. n water e Do not use detergents to clean the components Use a dry cloth only e Keep components in a clean dry place at room temperature e Dispose of old batteries in containers provided for this purpose e Avoid prolonged exposure to siren emissions e Do not paint or paper over the components e Do not try to open or move the components they are tamper protected and some of them may cause electric shocks Replacing the battery LED 2 indicates that the keypad battery may need to be replaced The keypad will continue to operate for up to one month after this event 1 Remove the keypad from the bracket with a suitable tool Depending on panel configuration a tamper alarm is sent to the panel and there is a 120 second delay before transmitting the specific tamper message to the monitoring station If tamper is restored before the end of the delay there is no transmission the tamper delay is only when the system is disarmed Tamper is immediately transmitted if the panel is armed 2 Remove the batteries and replace them with the new batteries 3 Install the keypad on its bracket WARNING RISK OF FIRE EXPLOSION AND BURNS DO NOT RECHARGE DISASSEMBLE HEAT ABOVE 100 C OR INCINERATE THE BATTERY WHILE THE BATTERY CAN NORMALLY BE SAFELY REMOVED BY HAND CARE SHOULD BE USED TO ENSURE THAT THE BATTERY TERMINALS ARE NOT SHORTED NOR THE BATTERY DAMAGED DURING THE REMOVAL PROCESS DISPOSE OF DEPLETED
9. ol ARMING AA panel has received a valid code or TAG and is Duration 4 seconds preparing to arm total set PARTIAL Sequence of 2 modulated When arming the partial SET sounds set confirms that the ARMING control panel has received ANNEX SET cO mne hn a valid code or TAG and ARMING Duration 2 5 seconds to arm partial Total set arming beeps Upon arming continue until final exit EXIT door is closed J DELAY Partial set arming beeps One beep per second continue for 30 seconds until partial set is armed After closing the final door ARMING When closing the final exit COMPLETE Fee door confirms that the Upon entry This entry tone lasts for ENTRY 30 seconds after you DELAY a sl open the entry door You one beep per second should disarm your system within this time Long and continuous beep When Disarming confirms that the control DISARMING panel has Duration 2 5 seconds been successfully disarmed FAULT 2 umes Y This signal indicates a E 4 fault in the system 4 beeps upon alert o Confirms the transmission ALERT sent via the keypad of an alert to the alarm company Defined by the user during installation Maintenance and recommendations e Check your system once a month or according to your operator s specifications e Avoid shocks to all the components and especially avoid dropping the Tags e Do not immerse components i
10. rical key the keypad also features an integrated siren as a deterrent and 4 LEDs to inform you on system status Siren output Tag reader area Audio output System armed LED LED1 System fault LED2 Intruder alarm LEDA Tamper alarm I LED3 Microphone Total set arming key Partial set arming key KEYPAD Arming using your code or tag Press an arming key on the keypad and enter the code or present a programmed TAG LE Arms the total set N Arms the partial set Arms the annex set the keypad must be associated with Total 7 el Annex When the keypad is dedicated to the annex set only the key will arm the annex set and the key will be disabled Arming can be performed with or without user identification depending on the panel setup The arming tone is emitted by the keypad followed by the exit delay beeps If a perimeter fault is signalled on arming disarm the system before checking all the doors and windows equipped with contacts Total set arming is completed after you close the final exit door After the door is closed the exit delay beeps stop and the arming complete tone is emitted by the panel and keypad siren Partial set or annex set arming is completed automatically at the end of the delay Depending on your system configuration Notes Always make sure that your arming request is followed by the arming tone Holding the TAG less than 1 min
11. stem In the latter case the annex set might need to be re armed Resetting the system after an alarm 4 If any of the LEDs 2 3 or 4 are flashing slowly an alarm has occurred see page 10 for detailed LED functionalities When there is an alarm in memory the system must be reset before it can be armed To reset the system 1 Disarm it using a valid code or present a tag 2 If there is more than one alarm in the memory repeat this operation for each alarm until LEDs 2 3 or 4 stops flashing slowly If LED 4 is flashing quickly on your keypad a confirmed alarm has occurred and a reset must be performed by your alarm company you cannot operate the system Call the operator Incorrect code protection Important If you enter five successive incorrect codes or present 5 invalid tags consecutively the keypad will be blocked for 5 minutes and an audible alarm will be triggered Personal attack Note This function is optional and can be set at installation You can send an alarm at any time even when your system is not armed Press and hold the Al and keys simultaneously The siren is triggered depending on the configuration The central monitoring station is alerted if the service is available Duress code Use a duress code if you are forced to disarm your security system under duress Your duress code is obtained by adding 1 to your code e g 1234 gt 1235 6789 gt 6780 The
12. ute in front of the keypad will not reverse the status Arming with a fault If the system diagnoses a fault on arming you cannot set the alarm Faults include system faults tampering and triggering of detectors A tone indicating a fault is emitted by the keypad after the arming request instead of the arming tone Check that all doors and windows fitted with contacts are closed You can override prevention of arming by requesting arming a second time within two minutes of the first request This will bypass all faults The arming process restarts the arming tone is emitted by the keypad followed by the exit delay beeps Arming is completed at the end of the delay Disarming using your code or tag To enable you to get to the keypad without triggering an alarm your installer may have programmed an entry delay To disarm your system Enter a valid code or present a programmed TAG The disarming tone is emitted by the panel and keypad siren Disarming the system will also stop the sirens if an alarm is triggered Important Stopping the siren does not interrupt the transmission of the alarm to the alarm company Notes Always make sure that your disarming request is followed by the disarming tone Always disarm the system when re entering the premises Holding the TAG in front of the keypad will not reverse the status Depending on your keypad s configuration this will disarm the total set or the entire sy
Download Pdf Manuals
Related Search