Home

Beverage-cooler

image

Contents

1. See Fig 7 4 Lower screws 10 Lower hinge 2 Button plug Fig 7 19 8 Place bottom LH corner of door onto lower hinge then install bushing and top hinge to cabinet Make sure door is level and it seals properly against cabinet then securely fasten three screws Snap top cap back onto hinge See Fig 8 Fig 8 9 Put the Criterion label over the hole on door top 20 Criterion Refrigerator Warranty Your product is protected by this warranty Warranty service must be obtained from Midea Consumer Services or an authorized Midea servicer Warranty One year full warranty from original purchase date includes compressor parts and labor only Midea through its authorized servicers will Pay all costs for repairing or replacing parts of this appliance which prove to be defective in materials or workmanship Midea is not responsible for Diagnostics removal transportation and reinstallation cost required because of service e Costs of service calls that are a result of items listed under NORMAL RESPONSIBILITIES OF THE CONSUMER Midea replacement parts shall be used and will be warranted only for the period remaining on the original warranty NORMAL RESPONSIBILITIES OF THE CONSUMER This warranty applies only to products in ordinary household use and the consumer is responsible for the items listed below 1 Proper use of the appliance in accordance with instructions prov
2. containing sands or acid Please regularly clean the scupper so the dew can be discharged al 2 Energy Saving e Please place the beverage cooler in dry and ventilated room The beverage cooler should not be placed in direct sunlight or close to heating sources such as radiator heater or cooking stove etc If necessary you can use heating insulation board e Try to shorten the opening time of the door e First let beverage cool down and then place the beverage into beverage cooler Try not to open the door too often especially when the weather is wet or hot Once you open the door remember to close it as soon as possible Every now and then check if the appliance is sufficiently ventilated adequate air circulation behind the appliance Always consider instructions stated in sections Positioning and Energy Saving Tips otherwise the energy consumption is substantially higher 13 Operation Noise Normal Noise Hum the noise is caused by operation of the refrigeration unit Coo rumbling or gurgle the noise is caused by flow of cooling agent in the pipeline Noise that can be eliminated easily To remove the noise caused by the unevenness of the wine cooler you can use a level and screw legs to match the even surface The noise generated when the beverage cooler leans against other furniture Move the beverage cooler away from the furniture or equipment on which the beverage cooler leans The noise c
3. from persons other than such Midea customer service or external causes such as abuse misuse inadequate power supply or acts of God Service calls resulting from improper installation of your product Service calls to instruct you on the use of your product o Surcharges including but not limited to any after hour weekend or holiday service calls tolls ferry trip charges or mileage expense for service calls to remote areas including the state of Alaska 41 lf the unit is put to commercial business rental or other use or application other than for consumer use we make no warranties express or implied including but not limited to any implied warranty of merchantability or fitness for particular use or purpose 42 Product that has been removed outside the USA or Canada 13 cuin de original serial numbers or products that have serial numbers which have been altered or cannot be readily etermined AON NODOJ 2 O 0 Note Some states do not allow the exclusion or limitation of incidental or consequential damages So this limitation or exclusion may not apply to you IF YOU NEED SERVICE Keep your bill of sale delivery slip or some other appropriate payment record should service be required The date on the bill established the warranty period If service is performed it is your best interest to obtain and keep all receipts This written warranty gives you specific legal rights You may also have other rights that vary from s
4. the chilling chamber e The number of bottles cans might be different for bottles with different shapes and sizes e Because some space is occupied by the compressor the lower part of the beverage cooler is comparatively less deep and it can be used to place beverage tins or short beverage bottles Effective Cubage Please see the nameplate on the beverage cooler for effective cubage Temperature Area in Chilling Cabinet Due to the air circulation in the beverage cooler some areas with different temperatures are generated The upper space has the highest temperature The lower space has the lowest temperature 11 Power off amp Stop Use of Beverage Cooler Turn off Beverage Cooler Pull out the power plug and the beverage cooler will be turned off Stop Using Beverage Cooler If you re not going to use the beverage cooler for a long time 1 Pull out power plug 2 Clean the beverage cooler 3 Open the door of beverage cooler Cleaning Beverage Cooler You should do the following operation 1 Pull out power plug 2 Scrub the sealing parts of the door with clean water only and immediately wipe the water off thoroughly 3 Please clean the beverage cooler with slightly warm water and a little detergent Do not splash water on the operation control element or the lighting system on the glass door 4 Reconnect the beverage cooler to a power source after it has been cleaned Hints Do not use detergent or solvent
5. Criterion User s Manual Beverage cooler OJD zi 07 210710 Ms Before using your product please read this manual carefully and keep it for future reference Content DIDS OM Sale AAA A ested nar emos 4 Key COMpone nts ccccceeee eee e eee eee e een neaeeeeeseceeeeenanaaess 6 Placement of Beverage Cooler 7 Leveling the Beverage Cooler 8 Temperature amp Ventilation see 8 MV CMU AION m aa aia 9 Connect Beverage Cooler to Power Source 9 Set up Temperature sia 9 Placement of Beverage Bottle Can 11 Temperature Area in Chilling Cabinet 11 Power off amp Stop Use of Beverage Cooler 12 Cleaning Beverage Cooler 12 Energy Saving seuren banni ds 13 Operation NOS Outras 14 TFOUDIESNOOUNAG sica dida 14 Reversing the Door SWINQ oooccccccccnoocccccccnncnnnnnnanonananonanas 10 C Disposal of Waste Package The package is used to protect the beverage cooler during the transportation All the materials are environmentally friendly and recyclable To get to know the current channel for disposal of castoff please consult professional dealers or local administrative authority FiWarning For discarded beverage cooler 1
6. E and F When the screen displays above mentioned errors please do not disassemble it to check by yourself You should contact local after sales service personnel for repair If the temperature in the cooler is too low it will display L When the temperature in the cooler is too high the screen will display H and will flash Under this state the cooler will buzz once every one second for 30 seconds One minute later the process will repeat for a total of three times before buzzer cancels You can press an key to cancel buzzer When the cooler is initially loaded the temperature in the cooler may rise 10 Hints for Operation In the operation of compressor the back wall of the chilling chamber may form water drops or frost this is determined by the functions of the beverage cooler You do not need to defrost or wipe off water drops because the back wall is able to defrost automatically The defrosted water will be collected to discharge channel and flow to the water receiver above the compressor and vaporized there When there is too much frost at the back of inner side of cabinet turn off the power until the defrosting is done Placement of Beverage Bottle Can When you place the beverage bottles please note e he number of bottles cans that can be put on the bottle racks is recorded on User Manual e To maintain the perfect air ventilation inside the beverage cooler the bottle should not touch the back wall of
7. Please pull out the plug of power source 2 Please sever the electric cord and take it off the cooler cabinet The beverage cooler contains cooling agent and insulation layer contains gas The cooling agent and the insulation gas must be disposed by professional personnel Please do not damage the loop pipeline of the cooling agent before it s delt by professional personnel 3 Risk of child entrapment Junked or abandoned appliances are still dangerous even if they will just sit in the garage for a few days 4 Before you throw away your old Wine Beverage Cooler take off the doors Leave the shelves in place so that children may not easily climb inside Tips on Safety Before Operating Beverage Cooler Please read the User s Manual carefully It contains important information on placement usage and maintenance of beverage cooler Please keep all the data for future use or for the beverage cooler s next user Technical Safety e The beverage cooler contains cooling agent R134a which is harmless to the environment Please pay attention not to damage the loop pipeline of the cooling agent in the transportation or installation The ejected cooling agent may cause injury to eyes or may ignite by itself When It s Damaged e Flame or fire source should be kept away from the beverage cooler e Please ventilate the room thoroughly for several minutes e Pull out the power plug e Inform after sales service personnel The m
8. at hold the upper hinge right side to the top of the cabinet Remove the Criterion logo on the top of glass door See Fig 1 Top ca Button plugs P dp UU MN 9Crews fas zr e uni i ul ps Hinge m MP Bushing Fig 1 2 Gently open the beverage cooler door lift the door and then put it on a padded surface to prevent scratching see Fig 2 HR L7 e te _ T E Ten Lun ao B m mmu Te om T A Te ms nr me a I uw m mL Lm F a St RC ae m ato pa m m auem m n aer 3 On bottom edge of door transfer door stop bracket screws and bushing etc to holes on the left hand after 180 reversing Then place the door on a padded surface to prevent scratching See Fig 3 ESA Door stop bracket NS N A OUO Door bracket screw 0 aa LITT MM ae ta 3 A a er Bushing E eS Light fixing screw Light switch A SOS a Sos avr os Fig 3 zl 4 Move the pin on the upper hinge to opposite hole see Fig 4 Pin Fig 4 5 Remove three screws that hold the bottom hinge to lower end of cabinet Remove the three button plugs from lower LH corner and transfer to holes where bottom hinge was just removed See Fig 5 Button plug Lower hinge Fig 5 Screws 18 6 Move lower hinge pin to opposite hole see Fig 6 Lower hinge pin 7 Fix the three button plugs lower hinge and screws at new positions switched position with each other
9. aused by mutual touch of bottles Please slightly separate the bottles from each other Troubleshooting Before you call the after sales service please check if you are able to remove the failures according to the following hints 14 Failures Possible Causes Remediation Measures Temperature is quite Sometimes the problem can be removed if you different from setting just turn off power of the value beverage cooler for 5 minutes and then restart it If the temperature is too high you can check it several hours later to see if the temperature is consistent with the setting value If the temperature is too low you can check the temperature again in the next day The inside of beverage YOu open the door of Reduce the frequency to beverage cooler very open the door of cooler is not cold often You place too many beverage cooler beverage bottles in it Wait for 4 5 hours The beverage cooler The beverage cooler is Press POWER button disconnected with power Check if power supply is doesnt cool down source or the power connected supply has stopped the power plug is not inserted firmly LED lamp is not on LED lamp is damaged Please contact the local after sales service personnel for repair 15 Reversing the Door Swing The glass door can be opened from left to right and vice versa Should you desire to change the opening direction please follow these instructions 1 Remove top cap Remove the three screws th
10. e fixation shaft Fixation Shaft of Handle Set Handle 2 Screw down the fixation pins of the handle with screw driver a um Handle Fixation Pin Screw Driver Leveling the Beverage Cooler Place the beverage cooler on the planned location and level it The front screw leg is adjustable Pay Attention to Room Temperature amp Ventilation The climate type is marked on the nameplate It indicates the room temperature range for operation of beverage cooler 2 de Notice If the room temperature is too low the wine cooler compressor may not start If the room temperature is higher than 90 F and the humidity is 75 RT the glass door of the beverage cooler may have condensation Ventilation The hot air on the side wall of the beverage cooler must be exhausted freely or the power consumption will be increased Therefore the distance between the beverage cooler and the wall or the nearby furniture should not be less than 1 6 inches This distance is the minimum requirement if you open the door to 90 Connect Beverage Cooler to Power Source After placing the beverage cooler please wait at least 30 minutes before operating the beverage cooler This is because the engine oil in the compressor may flow into the cooling system during the transportation Before the first running please clean the inside chambers of the beverage cooler Please see the section of Cleaning The power socket should be in a
11. ided with the product 2 Routine maintenance and cleaning necessary to keep the good working condition 3 Proper installation by an authorized service professional in accordance with instructions provided with the appliance and in accordance with all local plumbing electrical and or gas codes 4 Proper connection to a grounded power supply of sufficient voltage replacement of blown fuses repair of loosened connections or defects in house wiring 5 Expenses for making the appliance accessible for servicing 6 Damages to finish after installation EXCLUSIONS This warranty does not cover the following 1 Failure caused by damage to the unit while in your possession other than damage caused by defect or malfunction by its improper installation or by unreasonable use of the product including without limitation failure to provide reasonable and necessary maintenance or to follow the written Installation and Operating Instructions Products purchased as is or refurbished are not covered by this warranty Food loss caused by refrigerator or freezer failure Service calls to repair or replace consumables such as water filters light bulbs air filters etc or handles knobs and other cosmetic parts Product that has been transferred from its original owner Interior or exterior rust on the unit Damages caused by services performed by persons other than authorized Midea servicers use of parts other than Midea replacement parts obtained
12. ination of grease to the plastic components and the door sealing components of the beverage cooler otherwise this may cause small holes e Do not envelop or close the ventilation or exhaust holes Children e Do not give the package or other components to children The folded paperboard and the plastic film may cause suffocation e The beverage cooler is not a toy for children General Regulation The beverage cooler is applicable for e Chilling and the storage of beverages The beverage cooler is only designed for the household Key Components A l owl t a Fig 1 The illustration might be slightly different from the actual products Handle 2 Control Panel 8 Glass Shelves Glass Door 5 Light Switch Adjustable Legs Placement of Beverage Cooler The beverage cooler should be placed in a dry and ventilated room Keep away from direct sunlight The beverage cooler should be far away from heating sources such as cooking stove or heating radiator If the beverage cooler has to be placed near a heating source please adopt proper heating insulation board or keep the beverage cooler at least the following minimum distances away from the heating sources For electric stove 12 inches For oil or coal stove 12 inches Replacement of Door Hinge The door hinges of the beverage cooler can be interchanged between left and right sides Installation of Handle 1 Set the handle on th
13. ore cooling agent the beverage cooler has the bigger space to place the cooler is needed For every 0 018lb cooling agent there must be at least 1m of space in the room The weight of cooling agent is marked on the nameplate on the back plate of the beverage cooler e The replacement of power cord and other repair activities can only be carried out by the after sales service personnel specified by the manufacturers Improper installation or repair may cause great danger to users During Usage e Do not use electric appliances such as heater electric ice maker etc inside the beverage cooler Danger of Explosion e Do not use steam cleaning equipment to clean the beverage cooler or 4 to defrost Steam may enter the electric elements and cause short circuit Danger of Electric Shock e Don t remove frost or ice layers with sharp or keen edged objects otherwise the cooling agent pipeline may be damaged The ejected cooling agent may cause injury to eyes e Donot store products that contain combustible gas such as spray bottle or explosive materials in the beverage cooler Danger of Explosion e Do not use the base or the door of the beverage cooler as footplate or support e When you defrost or clean the beverage cooler please pull out the power plug When you pull out power plug please hold the plug rather than pull the power cord e The beverage with high alcohol content must be sealed and stored vertically e Avoid contam
14. place that can be conveniently reached The beverage cooler should be plugged into 115V 60Hz AC power PiWwarnina In any case please do not connect the beverage cooler to the electronic energy saving power plug or converter such as solar energy equipment ship s electric grid that convert DC into 115V AC Set up temperature See the following image Criterion Press this button once and the setting temperature increases by 1 F C Press this button once and the setting temperature decreases by 1 F C The temperature range MIN and MAX is 40 F 50 F 4 C 10 C which is ideal for beverage storage 80 Temperature display a LIGHT Lighting button for light control it controls the on off of lamp E POWER On off button used to turn on off all load Press LIGHT and POWER together for 2 seconds and you can convert between fahrenheit temperature and celsius temperature VN otice The default temperature of CBC46M1S is 41 F The beverage cooler is with Power Off Memory Function which means the display temperature will automatically resume to the customer set temperature once power resupplied When the cooler encounters a power failure the compressor s self protection mechanism will kick in which means the compressor will re start to work in 5 minutes after the power re supply Failure display If there is failure on the sensor the screen may display failure code such as
15. sp sod opezquejeb v1se oqjnpodc ns mpeg eysa Jod opibagond psa onpa ng CEEV 9V9 998 L 334 110 1 eec 1180 aapejuasoldoy 331095 JWOD E q3EQUOD DL JBI PUES Pepi pezungime ue Jo seres JSLUNSUOS ESpiy Aq pawuoed ec nu Apure nies Sy JAP UI sy ed pue sedas Jay Sun eGo Aus Reap Ag paeem si esugiddeg inei QUEJEA sau Aq papajoid si qanpiogd ana A jue JIem J9npo d oJonpojgd ep ENUEJESD ep amp jefi amp e pie juellem jonpoJg JUOMIA Postage Required Post Office will not deliver Without proper postage Criterion Product Support 11800 NW 100th Rd Suite 4 Medley FL 33178 Criterion CS1741 BP11M
16. tate to state Service under this warranty must be obtained by following these steps in order 1 Contact Midea Consumer Services or an authorized Midea servicer at 1 866 646 4332 2 If there is a question as to where to obtain service contact our consumer relations Department Criterion Tarjeta de Registracion de producto Es sencillo Cumple y envia su Tarjeta de Registraci n de Producto hoy Nombre tl ED O d b dl sl Direcci n ME LIU EUST 440 101400 5i Ciudad 1 11 JIU II Estado jCP399 Tel fono Opcional 1 11 L1 L E11 Direccion de E mail Opcional Donde Comprado LLLLLLLLLL umero de Modelo Muria de sana Mes Dim Ana 2202504418 REY 112 Fact dele compre Criterion Product Registration Card Its simple Complete and mail your Product Registration Card today Name ll tt ttt ttt tt ttt tt yt City BN EM LA d dL State Zip Phone Opliona PIL deel Li E mail Address Optional Where Purchased Le BA Model Pr os r 5 ena Mum ser March i 8g 202504418 REV 112 Cae al Purzhiusz Year CLEEV 9V9 998 1 Jano jg eapi e cunbje objes Lys 040 9181 400 mum ap pepucqg gj eus sepe JE DUES SD aea FdA UN JOI FEED UNOS EJES epi ap opezyocjne ajyueguaseical un jod a eapiy ap JOPILUNSUOS je SOEs so Jod epiiduima Jas eeqep ejjueJeB eye ua epioaigejsa sajsendai o gapas Jeuopodesd ep ugrseBigo 1embpenz e

Download Pdf Manuals

image

Related Search

Beverage cooler beverage cooler beverage coolers under counter beverage cooler refrigerator beverage cooler mini fridge beverage coolers with glass doors beverage cooler repair near me beverage cooler cart beverage cooler fridge beverage cooler undercounter glass door beverage cooler cabinet beverage coolers for sale beverage cooler repair near me service beverage cooler repair near me reviews beverage cooler commercial near me rental beverage cooler commercial near me repair beverage cooler commercial near me for sale beverage cooler repair near me cost newair beverage cooler zephyr beverage cooler true beverage coolers beverage air cooler commercial beverage cooler hisense beverage cooler

Related Contents

Samsung SPF-86P Digital Photo Frame User Manual  PEAQ PHP500AE User's Manual  mise en page print - Compagnie du Cercle  (Microsoft PowerPoint - 218435 Pi\350ge attractif Blattes Cafards  Hans Grohe Massaud 18020001 User's Manual  Hardware User Manual  Manuel d`utilisation  Strait-Flex CPR-100 Instructions / Assembly  喜多機械産業株式会社 (一社)日本建設機械レンタル協会  Notice - Castorama  

Copyright © All rights reserved.
DMCA: DMCA_mwitty#outlook.com.