Rugby 55 - Surveying Equipment
Contents
1. e Install the ceiling grid With the Rugby attached to the first piece of trim and adjusted to the desired height work can begin Attach the magnetic target to the ceiling grid and adjust the height of the grid until the rotating or scanning beam is striking the center of the target Applications Rugby 55 4 2 4 2 Using the Rugby in the Laying Down Position e Place the Rugby in the laydown position e Press the On Off Power Button to turn on the Rugby The Rugby will always turn on in automatic mode Allow the Rusby to self level e Press the Head Speed Button to stationary mode O rps The beam will move the the plumb down position for alignment over your reference marks e Start the head rotation or scanning motion to rough align the beam to a second control point Using the buttons on the laser or the remote fine adjust the beam until striking the second control point e Once aligned the split beam and rotating beams can be used to locate 90 angles for layout The rotating beam also creates a vertical plane for transferring points from the floor to the ceiling Applications Rugby 55 4 3 4 3 Using the Rugby with a Receiver e The rotating beam creates a level plane of laser light over the entire jobsite as a reference Use the Rugby together with a receiver when outdoors or in bright light conditions to locate the position of the beam2. e Place the Rugby on a flat level surface or tripod Place the Rugby in a location where the rotating beam will be at a convenient height and will not be obstructed e Press the On Off Power Button to turn on the Rugby The Rugby will always turn on in automatic mode Allow the Rugby to self level e Press the Head Speed Button to the fastest setting 10 rps e Use the plane of laser light as a reference to take eleva tion readings e Attach the receiver to a grade rod or stick Position the rod over a control point and adjust the height of the receiver until it is centered on the laser beam The receiver s bandwidth and audio volume can be adjusted using the buttons on the receiver Applications Rugby 55 4 4 4 4 More Applications Interior applications e Suspended ceilings Walls and Partitions Vertical alignment Transfer ring points from floor to ceiling Vertical plumb Layout of floors Squaring of angles Setting cabinets Chair rails and wainscoting e Align ment of wall and floor tiles Trim carpentry Setting sprinkler head heights Sloped ceilings Exterior applications e Setting elevation of forms and footings Squaring of forms Checking elevations and benchmarks Landscaping Drainage and septic systems e Fences and retaining walls Decks and patios Applications Rugby 55 4 5 5 In this chapter Batteries Batteries Topic 54 5 2 5 3 5 4 Pag
3. Complies with 21 CFR 1040 10 and 1040 11 except for deviations pursuant to Laser Notice No 50 dated July 26 2001 This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Type IR55 Art No 755008 S No Leica Geosystems AG CH 9435 Heerbrugg C Made in Singapore This device complies with part 15 of the FCC Rules Power 9V nominal 500mA max Manufactured Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Rugby 55 9 26 10 Rugby 55 Technical Data Technical Data Operating Range rotating beam 300 m 1000 ft Diameter with receiver Operating Range plumb beam up to 60 m 200 ft Self leveling Accuracy 2 6 mm at 30m 3 32 at 100 ft Self leveling Range 52 Rotation Speeds 0 2 5 10 rps Laser Diode Type 635 nm visible Dimensions HWD 158 x 163 x 166 mm 6 2 x 6 4 x 6 5 Weight with Batteries 1 85 Kg 4 0 Ibs Batteries Two D cells NiMH Pack Battery life alkaline NiMH 50 hours 30 hours Operating temp
4. next to the charge jack will turn on indicating that the Rugby is charging The LED will blink when a full charge has been reached e The batteries will reach a full charge in approxi mately eight hours if completely drained Batteries Rugby 55 5 5 q gt Accuracy Adjustment Accuracy Adjustment It is the responsibility of the user to follow operating instructions and to peri odically check the accuracy of the instrument and work as it progresses The Rugby is adjusted to the defined accuracy specification at the factory It is recommended to check your laser for accuracy upon receipt and periodically thereafter to ensure accuracy is maintained If your laser requires adjustment contact your nearest authorized service center or adjust the laser using the following procedure Do not enter this mode or attempt adjustment unless you plan to change the accuracy Accuracy adjustment should only be performed by a qualified indi vidual that understands basic adjustment principles This procedure is easier when performed with two people on a relatively flat surface Rugby 55 6 1 Accuracy Adjustment Checking Level Accuracy To check the level accuracy of your Rugby laser place the unit on a flat level surface or tripod approximately 100 ft 30 m from a wall 100ft 30m 1 100ft 30m 2 Align the first axis so that it is square to the wa
5. 2 Using the Rugby in the laydown position 4 3 Using the Rugby with a receiver 4 4 B Basic OperatlOn sisng Batter board clamp accessory Battery Charging the NiMH Batteries 5 5 OWVGIVIOW icc cet reete tbv etat do Cluund e E Replacing the Alkaline Batteries Replacing the NiMH Batteries 5 Beam Down function ssssssssss C Care and Transport eseeesesseeee 8 1 Case Configuration 1 4 1 5 Ceiling grid application 2 eects 4 2 Ceiling grid target accessory 3 5 Cleaning and Drying eese 8 4 D Description of the System sses 1 1 E Elevation alert description 2 12 Elevation alert enable disable 7 3 F Features pU 1 1 H Hazards Of USO 5e rex vp edere 9 8 L Labeling safety ssssssssesss Laydown operation application LED indicators do copre eth tenes teeta M Manual mode enable disable at start up 7 4 Manual Mode function sseessss 2 9 Membrane switch buttons sssssse 2 4 R Receivers use with 4 4 Remote control accessory susss 3 2 S Safety Electromagnetic Compatibility EMC 9 23 FCC rl p 9 25 Interided USE a nmt 9 3 Labeling 9 17 Laser Classification 9 14 Limits of Use nesciente tenue
6. 55 5 2 5 2 Replacing the Alkaline Batteries The Rugby has an LED to the left of the Power button that will flash when the batteries are low and will soon no longer power the laser When the batteries need replaced do the following e Loosen the silver knob a and remove the battery door b e Remove the dead batteries e Install two fresh batteries Ensure they are installed correctly by noting the battery symbols c on the top of the battery door Reinstall the battery door and tighten the silver screw securely to ensure a good seal Batteries Rugby 55 5 3 5 3 Replacing the NiMH Batteries The Rugby has an LED to the left of the Power button that will flash when the batteries are low and will soon no longer power the laser When the batteries need replaced or charged do the following e The rechargeable pack can be recharged without being removed from the laser e Toremove the rechargeable pack loosen the silver knob a and remove the pack b e Reinstall the battery pack and tighten the silver screw securely to ensure a good seal Batteries Rugby 55 5 4 5 4 Charging the NiMH Batteries The rechargeable NiMH battery pack on the Rugby can be charged without removing it from the To charge your Rugby battery pack please note the following e Connect the charger plug into the charge jack c on the Rugby battery pack e Plug the AC connector into the appropriate AC power source e The small LED d
7. 9 5 Responsibilities sesss 9 6 Rugby 55 Scan 90 function esses Sleep Mode function d SWITCH DUTIONS RP raa T Technical Data Transport Troubleshooting Ww Wallmount bracket accessory 3 4 Wattranty tec ceto edere eia hs 9 7 Total Quality Management Our commitment to total customer satisfaction Leica Geosystems AG Heerbrugg Switzerland has been certified as being equipped with a quality system which meets the International Standards of Quality Management and Quality Systems ISO standard 9001 and Environmen ISO 9001 1SO 14001 tal Management Systems ISO standard 14001 Ask your local Leica Geosystems dealer for more information about our TQM pro gram Years Warranty When registered within 8 weeks after purchase at www leica geosystems com registration Leica Geosystems AG Heinrich Wild Strasse CH 9435 Heerbrugg Switzerland Phone 41 71 727 3131 www leica geosystems com when it has to be right Switzerland 756717 1 0 3en Original text Printed in Switzerland 2008 Leica Geosystems AG Heerbrugg euca Geosystems
8. and position the laser beam directly over your reference point e The rotating beam and top plumb beam form a 90 reference for setting the form e Using the remote or the buttons on the Rugby align either of the beams to a second reference point The second beam will be your 90 reference Rugby 55 3 6 4 Applications In this chapter Topic Page 4 1 Installing Ceiling Grid ccceeeeeeeeeeeeeeeeee een 4 2 4 2 Using the Rugby in the Laying Down Position 4 3 4 3 Using the Rugby with a Receiver eeeeeseessesses 4 4 4 4 More Applications eseeeeeeeeeeeeeeennnnnnne nne 4 5 Applications Rugby 55 4 1 4 1 Installing Ceiling Grid e Attach the Rugby to the wallmount bracket The side with the control buttons should normally be facing outward Tighten the bottom locking knob until the Rugby is secured to the bracket e After mounting the first strip of ceiling trim at the desired height attach the wallmount bracket to the trim Tighten the locking knob on the top of the bracket e Press the On Off Power Button to turn on the Rugby The Rugby will always turn on in automatic mode Allow the Rugby to self level e Adjust the Rugby so that the rotating beam is at the desired height below the ceiling grid Loosen the adjust ment knob on the side of the bracket and slid the Rugby up or down When at the desired height retishten the adjustment knob
9. the batteries Rugby 55 9 11 A Warning A Warning Safety Directions High mechanical stress high ambient temperatures or immersion into fluids can cause leackage fire or explosions of the batteries Precautions Protect the batteries from mechanical influences and high ambient tempera tures Do not drop or immerse batteries into fluids Short circuited battery terminals can overheat and cause injury or fire for example by storing or transporting in pockets if battery terminals come in contact with jewellery keys metallized paper or other metals Precautions Make sure that the battery terminals do not come into contact with metallic objects Rugby 55 9 12 A Warning If the product is improperly disposed of the following can happen e If polymer parts are burnt poisonous gases are produced which may impair health e f batteries are damaged or are heated strongly they can explode and cause poisoning burning corrosion or environmental contamination e By disposing of the product irresponsibly you may enable unauthorized persons to use it in contravention of the regulations exposing themselves and third parties to the risk of severe injury and rendering the environment liable to contamination Precautions The product must not be disposed with household waste Dispose of the product appropriately in accordance with the national regulations in force in your country Always prevent access to the product by unauth
10. Directions Maximum average radiant power 0 5 mW 5 Maximum peak radiant power 4 75 mW 5 Pulse duration 5 6 2 2 and 1 1 ms Pulse repetition frequency 2 5 and 10 rps Beam divergence lt 1 5 mrad Direct intrabeam viewing is always hazardous Precautions Do not stare into the beam or direct it towards other people unnecessarily These measures are also valid for the reflected beam Looking directly into the reflected laser beam could be dangerous to the eyes when the laser beam is aimed at areas that reflect like a mirror or emit reflec tions unexpectedly e g prisms mirrors metallic surfaces windows Precautions Do not aim at areas that are essentially reflective such as a mirror or which could emit unwanted reflections Do not look through or beside the optical sight at prisms or reflecting objects when the laser is switched on Rugby 55 9 15 A Warning Safety Directions The use of Laser Class Illa equipment can be dangerous Precautions To counteract hazards it is essential for every user to respect the safety precautions and control measures Class Illa laser products used on construction sites and outdoors surveying alignment leveling a Only qualified and trained persons should be assigned to install adjust and operate the laser equipment b Proof of qualification of the laser equipment operator shall be available and in possession of the operator at all tim
11. Rugby 55 User Manual Version 1 0 ej English when it has to be right Seica Geosystems Introduction Product Product Identifica tion Congratulations on the purchase of a new Rotating Laser product The Rugby 55 is a laser tool for interior general construction and other leveling applications It is engineered and built with the latest innovations in the laser tool industry It is designed to be easy to set up simple to operate and highly dependable This manual contains important safety directions as well as instructions for setting up the product and operating it Refer to 9 Safety Directions for further information Read carefully through the User Manual before you switch on the product The model and the serial number of your product are indicated on the type plate Enter the model and serial number in your manual and always refer to this information when you need to contact your agency or Leica Geosystems authorized service workshop Type Serial No Rugby 55 II Symbols The symbols used in this manual have the following meanings Type Description A Danger Indicates an imminently hazardous situation which if not avoided will result in death or serious injury A Warning Indicates a potentially hazardous situation or an unin tended use which if not avoided could result in death or serious injury A Caution Indicates a potentially hazardous situation or
12. a X axis b Y axis C Z axis Accuracy Adjustment Rugby 55 6 5 2 3 4 In adjustment mode e The X axis LED is used to indicate changes to the X and Z axes a XO o The Y axis LED is used to indicate changes to the Y axis b To enter adjustment mode perform the following steps Turn the power off e With power off press and hold both the LEFT and RIGHT arrow buttons then press the ON button The active axis is the X axis a e If done correctly the following sequence of events will occur 1 The X and Y axis LED s will flash alternately three times The X axis LED will flash three times then flash slowly until level The Y axis LED will be off When leveled the X axis LED will turn ON not blinking Accuracy Adjustment Rugby 55 6 6 Adjusting the X axis e Pressing the LEFT or RIGHT arrow buttons increments the laser beam up X and down Each increment shall be indicated by a flash of the X axis LED and a beep from the audio indicator e Continue to press the buttons and monitor the spot until the unit is within its specified range Press the Auto Manual button to switch to the Y axis 1 The X and Y axis LED s shall flash alternately three times each 2 The Y axis LED will flash three times then flash slowly until level 3 The X axis LED will be off 4 When leveled the Y axis LED will turn ON not blinking Accuracy Adjustment Rugby 55 6 7 Accura
13. an unin tended use which if not avoided may result in minor or moderate injury and or appreciable material financial and environmental damage cg Important paragraphs which must be adhered to in prac tice as they enable the product to be used in a technically correct and efficient manner Trademarks All trademarks are the property of their respective owners Rugby 55 TI Table of Contents In this manual Chapter Page 1 Description of the System eeesssssseeeeeeeeeen 1 1 2 Basie OPSatlOM LR 2 1 3 ACCESSO ES arinnar eRT A ai 3 1 4 APDIICATIONS e T 4 1 5 Batteries ML 5 1 6 Accuracy Adjustment eeesssssssseeeneeeenee nennen 6 1 7 Troubleshootirig oor i teer nanna NEN aenea ineo anon 7 1 8 Care and TranspOFt nere eeeiee ck erre teeenaCe mama aiie 8 1 9 Satety Directions idee rete tre eene e vaca ae eee eaae ad 9 1 TQ Technical Data eerie nce erre 10 1 h qb E E E i 1 Rugby 55 IV 1 1 1 Precision Simplicity Ruggedness Description of the System Features Designed to maintain its accuracy on the toughest of jobs the Rugby 55 projects a rotating beam usable up to 150 meters 500 feet with a receiver The Rugby 55 is designed to be versatile easy to operate and having features that serve both the interior and general construction contractor well A bright visible
14. beam variable head speed scanning motion horizontal and vertical self leveling split beam and great battery life combine to provide consistent value for the professional contractor Engineered for construction environment the Rugby 55 will provide reliable performance day after day Description of the System Rugby 55 1 1 1 2 Rugby Components e f g a Window assembly and rotating head b Membrane switch panel C Battery door and locking knob d Charge port with LED rechargeable models e Carrying handle on back f 5 8 11 mounting holes on back and bottom Positioning guides Description of the System Rugby 55 1 2 1 3 Rugby 55 Membrane Switch Panel RUGBY 55 a b c d e g Low Battery LED Left Right Positioning Buttons Scanning Button Head Speed Button rps X Y Axis Level Indication LED s Power Button CW CCW Arrow Buttons Description of the System Rugby 55 1 3 1 4 Case Component Locator Interior Case o Ua k 8 C A 5 h d i e I 2 a Wall mount bracket b Spare battery holder c Alkaline batteries d Remote control e Ceiling grid targets f User manual g Receiver h Rugby 55 i Accessories compartment Descr
15. ble When not in use the laser product should be stored in a location where unauthorized personnel cannot gain access Precautions should be taken to ensure that the laser beam is not inten tionally directed at mirror like specular surfaces e g mirrors metal surfaces windows But more importantly at flat or concave mirror like surfaces The hazard distance is the distance from the laser at which the beam irra diance or radiant exposure equals the maximum permissible value to which personnel may be exposed without being exposed to a health risk Rugby 55 9 20 For products with an integrated distancer of laser class 3R this hazard distance is 103 m 337 feet At this distance the laser beam rates as Class 1 that means direct intrabeam viewing is not hazardous Safety Directions Rugby 55 9 21 Labeling Laser Class 3R Safety Directions Type R55 R ArCNo 753671 Power 30V 1 54 Leica Geosystems AG CH 9435 Heerbrugg Manufactured S No Made in Singapore Complies with 21 CFR 1040 10 and 1040 11 except for deviations pursuant to Laser Notice No 50 dated July 26 2001 This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation a Laser beam b Plumb beam Laser Radiation Avo
16. cy Adjustment Adjusting the Y axis Pressing the LEFT or RIGHT arrow buttons increments the laser beam up and down Each increment shall be indicated by a flash of the Y axis LED and a beep from the audio indicator e Continue to press the buttons and monitor the spot until the unit is within its specified range To Exit Press and hold the Auto Manual button for three seconds to exit adjustment mode and save the adjusted activity The X axis and Y axis LED s shall flash alternately three times each then the unit shall turn off Pressing the POWER button at any time while in adjustment mode shall exit the mode without saving any changes Rugby 55 6 8 To enter adjustment mode for the Z axis perform the following steps e Turn the power off and place the Rugby in the laydown position e With power off press and hold both the LEFT and RIGHT arrow buttons then press the ON button The active axis is the Z axis e If done correctly the following sequence of events will occur I 2 3 4 Accuracy Adjustment The X and Y axis LED s will flash alternately three times The X axis LED will flash three times then flash slowly until level The Y axis LED will be off When leveled the X axis LED will turn ON not blinking Rugby 55 6 9 xe Accuracy Adjustment Adjusting the Z axis vertical plane e Pressing the LEFT or RIGHT arrow buttons increments the laser beam s v
17. e Operating Principles esee 5 2 Replacing the Alkaline Batteries eeeeeeese 5 3 Replacing the NiMH Batteries ssseseeeeeeeeeee 5 4 Charging the NiMH Batteries cc cesceeeeeeeeeeeeeeseeneneeeeeee 5 5 The Rugby 55 can be purchased with either alkaline batteries or a rechargeable NiMH battery pack The following information is appropriate only to the model you have purchased Rugby 55 5 1 Batteries Operating Principles Primary use charging The battery must be charged prior to using it for the first time because it is delivered with an energy content as low as possible For new batteries or batteries that have been stored for a long time gt three months it is effectual to make 3 5 charge discharge cycles The permissible temperature range for charging is between O C to 40 C 32 F to 104 F For optimal charging we recommend charging the batteries at a low ambient temperature of 10 C to 20 C 50 F to 68 F if possible It is normal for the battery to become warm during charging Using the chargers recommended by Leica Geosystems it is not possible to charge the battery if the temperature is too high Operation Discharging The batteries can be operated from 20 C to 50 C 4 F to 122 F Low operating temperatures reduce the capacity that can be drawn very high operating temperatures reduce the service life of the battery Rugby
18. e Alert All three LED s on not flashing The Rugby is in an Ua NS i X Q Y environment where it cannot operate without causing damage to the laser This could most often be the result of direct sunlight Shade the unit The Rugby is working but not self leveling The Rugby must be in automatic mode to self level e n automatic mode both the X axis and Y axis LED s will blink green while leveling e In manual mode one or both of the X axis and Y axis LED s will be red Unit does not turn on This symptom may be caused by low or dead batteries e Check change or charge the batteries e Ifnotthe batteries the Rugby must be returned to an authorized service center for service The Rusgby s distance is reduced Dirt may be reducing the output of the laser e Clean the windows of the Rugby and the receiver to improve performance If not the windows the Rugby must be returned to an authorized service center for service Troubleshooting Rugby 55 7 2 Alert Symptom Possible Causes and Solutions The IR Remote is not working Check for proper operation of the remote e Check that the Rugby is turned on e The remote may be out side the usable distance e Aim directly at the laser for maximum distance e The remote s 9 volt battery may be low The laser receiver is not functioning prop erly See also your receiver manual Check for proper operation o
19. erature 20 to 50 C 4 to 122 F Storage temperature without batteries 40 to 70 C 40 to 158 F Protection against dust and water IP55 Rugby 55 10 1 IR Remote Control NiMH Battery Pack NiMH Charger Adapter Technical Data IR Remote range up to 40 m 130 ft IR Remote battery operation 9 volt alkaline up to two years Operating temperature 20 to 50 C 4 to 122 F Storage temperature without batteries 40 to 70 C 40 to 158 F Protection against dust and water IP54 Input voltage 7 5 VDC Input current LOA Charge time 8 hours Input voltage 100 240 VAC 55 60 Hz Output voltage 7 5 VDC Output current 1 0A Polarity Shaft neg Tip pos Accuracy is defined at 25 C Battery life is dependent upon environmental cond Rugby 55 itions 10 2 Rugby 55 Index A Accessories Batter board clamp suuss 3 6 Ceiling grid target ooo eee 3 5 Remote control 1i ert ntis 3 2 Wall mount bracket ssssse 3 4 Accuracy Adjusting level accuracy sss 6 5 Adjusting vertical accuracy 6 9 Checking level accuracy Checking vertical accuracy 6 4 Notes and responsibilities 6 1 Applications Ceiling grid installation 4
20. ertical position Each increment shall be indicated by a flash of the X axis LED and a beep from the audio indicator e Continue to press the buttons and monitor the spot until the unit is within its specified range To Exit Press and hold the Auto Manual hidden button for three seconds to exit adjustment mode and save the adjusted activity The X axis and Y axis LED s shall flash alternately three times each then the unit shall turn off Pressing the POWER button at any time while in adjustment mode shall exit the mode without saving any changes Rugby 55 6 10 7 Troubleshooting Alert Symptom Possible Causes and Solutions WP Low Battery Icon Flashing slowly Low Battery M flashing red or on not Flashing quickly Very Low Battery 71s flashing On not flashing Batteries will quit soon Replace alkaline batteries e Charge rechargeable batteries via xdi Elevation H I Alert Flashing quickly with audio beep Rugby has been x yY bumped or tripod has moved ZIN Z5 e Turn off Rugby to stop alert Allow unit to relevel L HI J and check the height of the unit Servo Limit All three LED s flashing slowly in a counter clockwise motion The Rugby is tipped too far to reach a level x 0 ey position Lpi e Relevel the Rugby within its wide five degree self leveling range Troubleshooting Rugby 55 7 1 Alert Symptom Possible Causes and Solutions Temperatur
21. es C Areasin which these lasers are used should be posted with an appropriate laser warning sign d Precautions should be taken to ensure that persons do not look directly with or without an optical instrument into the beam e When not in use the laser product should be stored in a location where unauthorized personnel cannot gain access f Precautions should be taken to ensure that the laser beam is not inten tionally directed at mirror like specular surfaces e g mirrors metal surfaces windows But more importantly at flat or concave mirror like surfaces Rugby 55 9 16 Labeling Laser Clas sification Illa AVOID EXPOSURE Laser radiation is emitted from this aperture LASER RADIATION AVOID DIRECT EYE EXPOSURE 820 6900m 4 75mW max CLASS llla LASER PRODUCT Type R55 A Art No 754835 Power 30V 15A Leica Geosystems AG CH 9435 Heerbrugg Manufactured S No WC Made in Singapore This laser product complies with 21CFR 1040 as applicable This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation a Laser beam b Plumb beam Safety Directions Rugby 55 9 17 Safety Directions Laser Classification Class 3R e A
22. f the receiver e The Rugby is not rotating It is leveling or in eleva tion alert e The receiver is out of usable range e The receiver s batteries are low Elevation alert func tion is not working The elevation alert function for the Rugby 55 is normally disabled on units from the factory e With unit turned on and rotating press and hold the LEFT and RIGHT arrow buttons then press the auto manual button to enable or disable this func tion The unit will beep once to indicate the change The Rugby does not turn on in automatic mode The Rugby 55 is designed to always turn on in auto matic mode unless specifically disabled by the user Troubleshooting Rugby 55 7 3 Alert Symptom Possible Causes and Solutions The Rugby turns on with the LAST MODE SAVED button to turn the unit off change e With automatic mode at start up disabled the turned off e With unit turned on and rotating press the off on e Press and hold both the auto manual and off on buttons for five seconds to enable or disable this function The unit will beep once to indicate the Rugby will turn on with the last mode used when Troubleshooting Rugby 55 7 4 8 In this chapter Care and Transport Care and Transport Topic Page 8 1 Trasport EE 8 2 8 2 Er rc ee 8 3 8 3 Cleaning and Drying eesssseeseeeeeeennnnnnn nnne 8 4 Rugby 55 8 1 8 1 Trans
23. ge inspect the field adjustment parameters given in this user manual before using the product Refer to section 10 Technical Data for information about storage temperature range At the recommended storage temperature range batteries containing a 10 to 50 charge can be stored for up to one year After this storage period the batteries must be recharged Remove batteries from the product and the charger before storing After storage recharge batteries before using Protect batteries from damp and wetness Wet or damp batteries must be dried before storing or use Rugby 55 8 3 8 3 Cleaning and Drying Product and Accesso Blow dust off optical parts ries e Never touch the glass with your fingers e Use only a clean soft lint free cloth for cleaning If necessary moisten the cloth with water or pure alcohol e Do not use other liquids these may attack the polymer components Damp Products e Dry the product the transport container the foam inserts and the acces sories at a temperature not greater than 40 C 108 F and clean them e Do not repack until everything is completely dry Cables and Plugs e Keep plugs clean and dry e Blow away any dirt lodged in the plugs of the connecting cables Care and Transport Rugby 55 8 4 9 Safety Directions In this chapter Topic 9 1 G n r l aiiai aeaa tai da Eiana anaE Taaa SAARE 9 2 Intended WSC istics ee cec cites stesa shes EENAA 9 3 Limits of ULT oe 9 4 Responsibi
24. he Scan 90 b feature can quickly bring the scanning beam to you e Scan Memory means that you can switch to rotational or stationary mode and the scan will return to the previous posi tion wheh scanning motion is again chosen mic Basic Operation Rugby 55 2 7 Sleep Mode tg HU Press both the Up and Down buttons simultaneously on the Remote to put the Rugby 55 into Sleep Mode During Sleep Mode all functions are disabled The Low battery indicator will flash once every ten seconds to indicate that the unit is in sleep mode The Rusby will sleep for up to two hours then will shut off automatically and must be turned on again at the laser When in Sleep Mode pressing any key will wake the unit and normal oper ation will resume Basic Operation Rugby 55 2 8 2 5 Manual Mode with cross axis self leveling The Rugby is designed to always start up in automatic mode It may be desirable to save a manual setup The automatic mode on start up can be disabled using a special procedure found in the Troubleshooting section Press the Auto Manual Button once to change the Y axis to manual mode A e The Y axis will not self level and slope can be entered in this axis using the Mw arrow buttons on the Rugby or the remote control xe e Pug The X axis will continue to self level L ial e The Y axis LED will be red e The X axis LED will blink green until level When the Y axis is in manual mode the Y axis can be slo
25. id direct eye exposure Class 3R Laser Product according to IEC 60825 1 1993 A1 1997 A2 2001 Pg lt 0 5 mw 620 690 nm Rugby 55 9 22 9 8 Description A Warning A Caution Safety Directions Electromagnetic Compatibility EMC The term Electromagnetic Compatability is taken to mean the capability of theproduct to function smoothly in an environment where electromagnetic radiation and electrostatic discharges are present and without causing elec tromagnetic disturbances to other equipment Electromagnetic radiation can cause disturbances in other equipment Although the product meets the strict regulations and standards which are in force in this respect Leica Geosystems cannot completely exclude the possi bility that other equipment may be disturbed There is a risk that disturbances may be caused in other equipment if the product is used in conjunction with accessories from other manufacturers for example field computers personal computers two way radios non standard cables or external batteries Precautions Use only the equipment and accessories recommended by Leica Geosystems When combined with the product they meet the strict requirements stipulated by the guidelines and standards When using computers and two way radios pay attention to the information about electromagnetic compatibility provided by the manufacturer Rugby 55 9 23 A Caution A Warning Safety Directions Di
26. ific to your jobsite requirements Basic Operation Rugby 55 2 2 2 2 xe er Lyi b e amp Basic Operation The LED Indicators The LED Indicators have three main functions e To indicate the level status of the axes e To indicate the battery status e To indicate an H I Alert condition Additional functions will be described for specific conditions later in this manual X and Y Indicators a Indicate the level status e Green Indicates the axis is level e Green Flashing Indicates the axis is leveling e Red Indicates the axis is in Manual mode e Both Flashing Red Indicates an H I Alert condition if H I is enabled Low Battery Indicator b When the LED is off the battery is still good When it is flashing slowly the battery is getting low When the LED begins to flash rapidly it is time to change the batteries Rugby 55 2 3 N 3 NWO Basic Operation The Switch Buttons Off On Power Button e Press to turn the Rugby On and Off Head Speed Button e Press to change the speed of the head rotation 0 2 e 5e 10 rps Scan Mode Button e Press to change the width of the scanning beam 10 45 e 90 e 180 Automatic Manual Mode Button e Press to change the Y axis to manual mode e with X axis self leveling e Press again to change the X axis to manual mode e with Y axis self leveling e Press again to change both axes to manual mode with no self leveling Press agai
27. instruction or the inadequate imparting of instruction can lead to incorrect or adverse use and can give rise to accidents with far reaching human material financial and environmental consequences Precautions All users must follow the safety directions given by the manufacturer and the directions of the person responsible for the product A Caution Watch out for erroneous measurement results if the product has been dropped or has been misused modified stored for long periods or trans ported Precautions Periodically carry out test measurements and perform the field adjustments indicated in the user manual particularly after the product has been subjected to abnormal use and before and after important measurements Safety Directions Rugby 55 9 8 A Danger A Warning Safety Directions Because of the risk of electrocution it is very dangerous to use grade rods and staffs in the vicinity of electrical installations such as power cables or electrical railways Precautions Keep at a safe distance from electrical installations If it is essential to work in this environment first contact the safety authorities responsible for the elec trical installations and follow their instructions By working in a thunderstorm you are at risk from lightning Precautions Do not carry out field work during thunderstorms Rugby 55 9 9 A Warning A Caution Safety Directions Inadequate securing of the working
28. ion mounted on a tripod The Rugby 55 has also a 5 8 11 mounting hole in the side of the housing to allow the laser to be attached directly to a tripod or batter board clamp in the laying down position The interior carrying case of the Rugby 55 is designed to allow the wall mount to remain attached to the Rugby while in the carrying case This reduces the setup time and need to adjust the height of the bracket each time the Rugby is used Rugby 55 3 4 3 3 The Ceiling Grid Target The Ceiling Grid Target Leica e Allows the user to visually detect the rotating or scanning beam ex throughout the jobsite The ceiling grid target s magnet attaches to the ceiling grid e The beam can be viewed as it reflects off the foil on the back of the target E or through the target at the sides of the foil p CM e The ceiling grid can then be adjusted until the beam is hitting the center line of the target Ke em ali Py O e Asmall bracket on the back of the target allows the target to be set up over a control point for layout alignment a Accessories Rugby 55 3 5 3 4 Accessories The Batter Board Clamp The Batter Board Clamp e The batter board clamp is a simple device that allows the Rugby to be attached directly to the batter board for squaring of forms e Attach the clamp to the 5 8 11 mounting hole in the side of the Rugby e Attach the batter board clamp to the form
29. iption of the System Rugby 55 1 4 1 5 Case Component Locator Standard Case a User manual b Accessories and second receiver c Spare batteries D cells d Spare battery pack NiMH e Receiver f Rugby Description of the System Rugby 55 1 5 2 In this chapter Basic Operation Basic Operation Topic Page 2 1 IMEROGUCHON Pom 2 2 2 2 The LED INGICAONS sees scccessassssecerccccctcesdesccessnsedeccessessssaveeeseans 2 3 23 The Switch Buttons reete nnne iu nte eno nhan 2 4 2 4 Special Feat res nennen picea uaiiie i aai 2 6 2 5 Manual Mode with cross axis self leveling 2 9 2 6 The Elevation Alert H l Function cesses 2 12 Rugby 55 2 1 2 1 Introduction 1 The Rugby 55 is easy to understand and simple to use The descriptions of the LED s and Switch Buttons that follow will explain their basic functions he Rugby 55 is designed to serve you in a variety of applications Developed specifically for the interior contractor the Rugby 55 can also be used together with a laser receiver for many outdoor general construction applications 1 ti his manual contains operating and set up procedures for common applica ons Its purpose is to describe the features of the Rugby 55 and how it oper ates This manual is not intended to describe specific applications Contact Leica Geosystems or your distributor for information spec
30. l at a lower height e The Elevation Alert function becomes active and monitors the movement of the laser 30 second after the unit has completely leveled and the head starts rotating e The elevation alert monitors the laser and both the X and Y axis LED s will begin flashing and the Rugby will beep rapidly if disturbed e To stop the alert turn Rugby off and on again Check the height of the instrument before beginning to work again The elevation alert feature of the Rugby 55 is normally OFF when shipped It can be enabled to turn on automatically every time the Rugby is turned on by using a special procedure found in the Troubleshooting section Rugby 55 2 12 3 Accessories In this chapter Topic Page 3 1 The IR Remote Control ccccecceeeeeeeeseseeesseneeeeeeeeeeeeeeeeeeeeeee 3 2 dud The Wall MOUNE iic aaeeea anaa E 3 4 33 The Ceiling Grid Target cesseeeeen 3 5 3 4 The Batter Board Clamp ctcececeeeeeeeeeeeeeeeenneeeeeeeeeeeeeeeeees 3 6 Accessories Rugby 55 3 1 Accessories The IR Remote Control The IR Remote Control communicates with the Rugby via infrared signals and is used to control the same functions as on the laser el BP BW a CW and CCW Buttons Press to rotate the stationary and scanning beam in a CW or CCW motion b Left and Right Buttons Press to tilt the Y axis when it is manual mode I
31. litiGs 2 none ttti nett 9 5 International Warranty seeeeeeeeeen 9 6 Hazards of Use 5 oiii eie an ete eyar esee eere ad 9 7 Laser Classification eese 9 8 Electromagnetic Compatibility EMC si 9 9 FCC Statement Applicable in U S ssssssssesssseersrrrrrrrerrssses 9 25 Safety Directions Rugby 55 9 1 9 1 Description Safety Directions General The following directions should enable the person responsible for the product and the person who actually uses the equipment to anticipate and avoid oper ational hazards The person responsible for the product must ensure that all users understand these directions and adhere to them Rugby 55 9 2 9 2 Permitted Use Adverse Use Safety Directions Intended Use The product casts a horizontal laser plane for the purposes of alignment The unit can be set up on it s own base plate or on a tripod The laser beam can be detected by means of a laser detector The product combined with machine control receivers is also suitable for guiding construction machinery Use of the product without instruction Use outside of the intended limits Disabling safety systems Removal of hazard notices Opening the product using tools for example screwdriver unless this is specifically permitted for certain functions Modification or conversion of the product Use after misappropriation Use of products with ob
32. ll Allow the unit to self level completely approximately one minute after the unit begins to rotate then mark the position of the beam Position 1 Rotate the laser 180 allow it to self level and mark the opposite side of the first axis Position 2 Rugby 55 6 2 Accuracy Adjustment 100ft 30m 3 cee AXN 100ft 30m IS 4 HERE ORE Align the second axis of the Rugby by rotating it 90 so that this axis is now square to the wall Allow the unit to self level completely then mark the position of the beam Position 3 Rotate the laser 180 allow it to self level and mark the opposite side of the first axis Position 4 The Rugby is within its accuracy specification if the four marks are within 3 32 2 6 mm from the center Rugby 55 6 3 Accuracy Adjustment Checking Vertical Accuracy To check the vertical accuracy of your Rugby laser place the unit in the laydown position on a flat level surface approximately 50 100 ft 15 30 m from a wall e Hang a plumb line on the wall e Move the Rugby until the vertical rotating beam is aligned to the plumb line e Ifthe rotating beam is not plumb adjustment is necessary Rugby 55 6 4 Adjusting Level Accuracy The checking and adjustment of the accuracy of the Rugby 55 requires a two step process e Checking and adjusting the horizontal plane The X and Y axes e Checking and adjusting the vertical plane The Z axis
33. n the laydown position press to align the rotating and 90 split beam c Up and Down Arrow Buttons Press to tilt the X axis when it is manual mode d Auto Manual Button Press to change desired axis to manual mode Rugby 55 3 2 e e Head Speed Button Press to change the speed of the head rotation f f Scan Mode Button Press to change width of the scanning motion g g Sending LED e R The sending LED flashes to indicate that the remote is sending a signal to the Rugby e The remote control is powered by a 9 volt type battery The battery can only be accessed by removing the four screws and the back cover of the remote Care should be taken when re assembling the cover to ensure the o ring seal is properly in place Accessories Rugby 55 3 3 3 2 Accessories The Wall Mount The Wall Mount Bracket Assembly e Allows the user to mount the Rugby on a wall grid at the necessary height The rotating beam then provides a reference height to hang the ceiling grid e Mount the Rugby to the wall mount and tighten the locking knob a e Mount the Wall mount to the ceiling grid and tighten the locking mecha nism b e To adjust the height loosen the adjustment knob c on the side of the bracket then slide the bracket up or down until the desired height is achieved Retighten the adjustment knob A5 8 11 mounting hole is molded into the back of the bracket for using the Rugby in the laying down posit
34. n to change back to full automatic mode Note the changes in the LED indicators in these manual modes The red LED indicates that the axis is in manual mode Rugby 55 2 4 Basic Operation Clockwise and Counter Clockwise Buttons CW amp CCW Press to rotate the stationary and scanning beam in a CW or CCW motion Manual Mode Slope and Layout Buttons Press to tilt the axis that is set to manual mode In the laydown position press to align the rotating and 90 split beam Rugby 55 255 2 4 Special Features Beam Down lt gt B e Press the Head Speed Button to stop the rotating head zero rps The pr position of the beam will automatically move to the downward position to allow the user to align the Rugby over a reference point on the floor Changing to O rps positions the beam in the plumb down position Basic Operation Rugby 55 2 6 Scan 90 and Scan Memory E ape wa Press and hold either the CW or CCW button then press the 3 E Scan or Head Speed Button to quickly move the scanning or stationary beam at 90 intervals In scan mode the scan width will automatically change to the smallest scan width c 5 when this function is activated e For layout work use the Beam Down feature a to position the beam over a reference point Then use the Scan 90 feature b to quickly move the small scan to a position to the left or right of the laser e For ceiling applications and marking elevations t
35. ns Do not look through or beside the optical sight at prisms or reflecting objects when the laser is switched on The use of Laser Class 3R equipment can be dangerous Precautions To counteract hazards it is essential for every user to respect the safety precautions and control measures specified in the standard IEC 60825 1 2001 08 resp EN 60825 1 1994 A11 1996 A2 2001 within the hazard distance pay particular attention to Section Three Users Guide Following is an interpretation of the main points in the relevant section of the standard quoted Rugby 55 9 19 Safety Directions Class 3R Laser Products used on construction sites and outdoors surveying alignment leveling a b c d e f g Only qualified and trained persons should be assigned to install adjust and operate the laser equipment Areas in which these lasers are used should be posted with an appropriate laser warning sign Precautions should be taken to ensure that persons do not look directly with or without an optical instrument into the beam The laser beam should be terminated at the end of its useful path and should in all cases be terminated if the hazardous beam path extends beyond the limit hazard distance of the area in which the presence and activities of personnel are monitored for reasons of protection from laser radiation The laser beam path should be located well above or below eye level wher ever practica
36. orized personnel Product specific treatment and waste management information can be down loaded from the Leica Geosystems home page at http www leica geosys tems com treatment or received from your Leica Geosystems dealer A Warning Only Leica Geosystems authorized service workshops are entitled to repair these products Safety Directions Rugby 55 9 13 9 7 General A Warning Safety Directions Laser Classification This rotating laser Rugby 55 produces a visible laser beam which emerges from the rotating head There are two versions of the Rugby 55 These two models represent varia tions in laser output All other functions and features are the same on both models Review the information below for the unit you have purchased The products are clearly identified by article number serial number and safety label Laser Classification Class Illa e Article number 754835 e Serial number 550 00000 to 550 49999 e Warning label Class Illa LASER PRODUCT The product is a Class Illa Laser Product in accordance with e FDACFR21 CFR 1040 10 April 2002 US Department of Health and Human Service Code of Federal Regulations Class Illa Laser Products Direct intrabeam viewing is always hazardous Avoid direct eye exposure The accessible emission limit is within five times the accessible emission limits of Class 2 Il in the wavelength range from 400 nm to 700 nm Rugby 55 9 14 A Warning A Warning Safety
37. ped as illustrated here The X and Y axes are marked on the top of the Rugby Basic Operation Rugby 55 2 9 Press the Auto Manual Button again to change the X axis to manual mode e The X axis will not self level and slope can be entered in this axis using the vh arrow buttons on the Rugby or the remote control xe ov e The X axis LED will be red 4 The Y axis will continue to self level L TN The Y axis LED will blink green until level When the X axis is in manual mode the X axis can be sloped as illustrated here The X and Y axes are marked on the top of the Rugby Basic Operation Rugby 55 2 10 Press the Auto Manual Button again to change to full manual mode e Both the X axis and Y axis will not self level and slope can be entered in either or both axes using the arrow buttons on the Rugby Y axis or the A remote control either axis xe ev e The X axis LED will be red L T J e The Y axis LED will be red When both the X and Y axes are in manual mode both axes can be sloped as illustrated here The X and Y axes are marked on the top of the Rugby Basic Operation Rugby 55 2 11 2 6 7 rA xe e Lyi Basic Operation The Elevation Alert H I Function e The Elevation Alert or Height of Instrument function is designed to prevent incorrect work caused by sudden movement or settling of the tripod that would cause the laser to leve
38. port in the field Transport in a road vehicle Shipping Shipping transport of batteries Field Adjustment Care and Transport Transport When transporting the equipment in the field always make sure that you e either carry the product in its original transport container e or carry the tripod with its legs splayed across your shoulder keeping the attached product upright Never carry the product loose in a road vehicle as it can be affected by shock and vibration Always carry the product in its transport container and secure it When transporting the product by rail air or sea always use the complete original Leica Geosystems packaging transport container and cardboard box or its equivalent to protect against shock and vibration When transporting or shipping batteries the person in charge of the product must ensure that the applicable national and international rules and regula tions are observed Before transportation or shipping contact your local passenger or freight transport company After transport inspect the field adjustment parameters given in this user manual before using the product Rugby 55 8 2 8 2 Product Field Adjustment NiMH Batteries Care and Transport Storage Respect the temperature limits when storing the equipment particularly in summer if the equipment is inside a vehicle Refer to Technical Data for information about temperature limits After long periods of stora
39. r in a particular installation If this equipment does cause harmful interference to radio or television recep tion which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Rugby 55 9 25 Changes or modifications not expressly approved by Leica Geosystems for compliance could void the user s authority to operate the equipment A Warning Labeling Rugby 55 a Laser class Illa Laser class 3R Safety Directions Type R55 A Art No 754835 Power 3 0V 1 5A Leica Geosystems AG CH 9435 Heerbrugg Manufactured S No Made in Singapore This laser product complies with 21CFR 1040 as applicable This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Type R55 R Art No 753671 Power 3 0V 1 5A Leica Geosystems AG CH 9435 Heerbrugg Manufactured S No Made in Singapore
40. rticle number 753671 e Serial number 550 50000 to 550 99999 e Warning label Class 3R LASER PRODUCT The product with a stationary rotating head is a Class 3R Laser Product in accordance with e EC 60825 1 2001 08 Safety of Laser Products e EN 60825 1 1994 A11 1996 A2 2001 Safety of Laser Products Class 2 product if rotating head is rotating or scanning Class 3R Laser Products Direct intrabeam viewing is always hazardous Avoid direct eye exposure The accessible emission limit is within five times the accessible emission limits of Class 2 in the wavelength range from 400 nm to 700 nm Maximum average radiant power 0 5 mW 596 Maximum peak radiant power 4 75 mW 596 Pulse duration 5 6 2 2 and 1 1 ms Pulse repetition frequency 2 5 and 10 rps Beam divergence 1 5 mrad Rugby 55 9 18 A Warning A Warning A Warning Safety Directions Direct intrabeam viewing is always hazardous Precautions Do not stare into the beam or direct it towards other people unnecessarily These measures are also valid for the reflected beam Looking directly into the reflected laser beam could be dangerous to the eyes when the laser beam is aimed at areas that reflect like a mirror or emit reflec tions unexpectedly e g prisms mirrors metallic surfaces windows Precautions Do not aim at areas that are essentially reflective such as a mirror or which could emit unwanted reflectio
41. site can lead to dangerous situations for example in traffic on building sites and at industrial installations Precautions Always ensure that the working site is adequately secured Adhere to the regu lations governing safety and accident prevention and road traffic If the accessories used with the product are not properly secured and the product is subjected to mechanical shock for example blows or falling the product may be damaged or people may sustain injury Precautions When setting up the product make sure that the accessories are correctly adapted fitted secured and locked in position Avoid subjecting the product to mechanical stress Rugby 55 9 10 A Caution A Warning Safety Directions During the transport shipping or disposal of batteries it is possible for inap propriate mechanical influences to constitute a fire hazard Precautions Before shipping the product or disposing of it discharge the batteries by running the product until they are flat When transporting or shipping batteries the person in charge of the product must ensure that the applicable national and international rules and regulations are observed Before transpor tation or shipping contact your local passenger or freight transport company Using a battery charger not recommended by Leica Geosystems can destroy the batteries This can cause fire or explosions Precautions Only use chargers recommended by Leica Geosystems to charge
42. sturbances caused by electromagnetic radiation can result in erroneous measurements Although the product meets the strict regulations and standards whichin this respect Leica Geosystems cannot completely exclude the possibility product may be disturbed by very intense electromagnetic radiation near radio trans mitters two way radios or diesel generators Precautions Check the plausibility of results obtained under these conditions If the product is operated with connecting cables attached at one of their two ends for example external supply cables interface cables the permitted level of electromagnetic radiation may be exceeded and the correct functioning of other products may be impaired Precautions While the product is in use connecting cables for example product to external battery product to computer must be connected at both ends Rugby 55 9 24 9 9 A Warning Safety Directions FCC Statement Applicable in U S This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communication However there is no guarantee that interference will not occu
43. systems is responsible for supplying the product including the user manual and original accessories in a completely safe condition The manufacturers of non Leica Geosystems accessories for the product are responsible for developing implementing and communicating safety concepts for their products and are also responsible for the effectiveness of those safety concepts in combination with the Leica Geosystems product The person in charge of the product has the following duties e To understand the safety instructions on the product and the instructions in the user manual o be familiar with local regulations relating to safety and accident preven tion o inform Leica Geosystems immediately if the product and the application becomes unsafe The person responsible for the product must ensure that it is used in accord ance with the instructions This person is also accountable for the training and the deployment of personnel who use the product and for the safety of the equipment in use Rugby 55 9 6 9 5 International Warranty Safety Directions International Warranty The International Warranty can be downloaded from the Leica Geosystems AG home page at http www leica geosystems com internationalwarranty or received from your Leica Geosystems dealer New Register your product at www leica geosystems com registration to extend the warranty Rugby 55 9 7 9 6 Hazards of Use A Warning The absence of
44. viously recognizable damages or defects Use with accessories from other manufacturers without the prior explicit approval of Leica Geosystems Inadequate safeguards at the construction site for example when using on or near roads Deliberate dazzling of third parties Rugby 55 9 3 e Controlling of machines moving objects or similar monitoring application without additional control and safety installations A Warning Adverse use can lead to injury malfunction and damage It is the task of the person responsible for the equipment to inform the user about hazards and how to counteract them The product is not to be operated until the user has been instructed on how to work with it Safety Directions Rugby 55 9 4 9 3 Environment A Danger Safety Directions Limits of Use Suitable for use in an atmosphere appropriate for permanent human habita tion not suitable for use in aggressive or explosive environments Local safety authorities and safety experts must be contacted before working in hazardous areas or in close proximity to electrical installations or similar situations by the person in charge of the product Rugby 55 9 5 9 4 Manufacturer of the product Manufacturers of non Leica Geosys tems accessories Person in charge of the product A Warning Safety Directions Responsibilities Manufacturer of the product Leica Geosystems AG CH 9435 Heerbrugg here inafter referred to as Leica Geo
Download Pdf Manuals
Related Search