Home

Liquid Allocation Program for Continuous Flow

1. 1 Point Description R W AC 30 30 ASCII ss Description of the liquid meter characters 2 Liquid Product Point R W UINT8 1 0 1 0 The liquid product point 0 based point type 23 assigned to the liquid meter 3 Meter Units Type R W UINT8 1 0 gt 1 0 Indicates the type of units for the flow meter input This is only used with linear meters 0 Volume 1 Mass 4 Reserved R W UINT8 1 0 0 Reserved 5 Reserved R W UINT8 1 0 0 Reserved 6 Reserved R W FL 1 0 0 Reserved 7 Alarming Option R W UINT8 1 045 0 If enabled the indicated parameter for the liquid meter is compared to the alarm limits and the alarm statuses set and cleared accordingly 0 Disabled 1 Enabled for Indicated Volume Flowrate parameter 27 2 Enabled for Gross Volume Flowrate parameter 29 3 Enabled for Gross Standard Volume Flowrate parameter 31 4 Enabled for Net Standard Volume Flowrate parameter 33 Enabled for Mass Flowrate parameter 35 70 Reference Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name Access Data Length Range Default Description Type 8 RBX on Clear R W UINT8 1 0 gt 1 0 Enable disable status for an RBX alarm when an alarm condition clears 0 RBX on Clear Disabled 1 RBX on Clear Enabled 9 RBX on Set R W UINT8 1 0 1 0 Enable disable status for an RBX alarm when an alarm condition gets set 0 RBX on Set Disabled 1
2. Reserved Bit 2 High observed density alarm status 0 High observed density alarm status Is clear 1 High observed density alarm Status is set Bit 1 Reserved Bit 0 Low observed density alarm status 0 Low observed density alarm Status Is clear 1 Low observed density alarm Status is set 104 Reference Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Point Type 26 Densitometer Parameters Parm Name Access Data Type Length Range Default Description 36 Low Density Alarm Limit R W FL 4 gt 0 0 300 0 Low observed density alarm limit in the units specified for the observed density TLP 22 0 3 37 High Density Alarm Limit R W FL 4 gt 0 0 1200 0 High observed density alarm limit in the units specified for the observed density TLP 22 0 3 38 Alarm Deadband R W FL 4 gt 0 0 5 0 The alarm deadband is the amount the observed density must be above the low alarm limit parameter 36 or below the high alarm limit oarameter 37 before the associated alarm clears The units are those specified for the observed density TLP 22 0 3 Rev July 15 Reference 105 Liquid Allocation Program for Continuous Flow User Manual For Customer Service and Technical Support Dial 1 800 537 9313 Headquarters Emerson Process Management Remote Automation Solutions 6005 Rogerdale Road Houston TX 77072 U S A T 1 281 879 2699 F 1 281 988 4445 www EmersonProcess com Remo
3. 2 Update Figure 16 b Liquid Meters Inputs tab Meter Type is Orifice 2 Review and change as necessary the values in the following fields Field Flow Meter Input Rev July 15 Description Sets the source for the flow input for the liquid meter Click to display the Select TLP screen and specify the TLP selection If the meter type is linear the units are volume time or mass time where the units for volume mass and time are specified on the Liquid Preferences screen If the meter type is orifice the units are the units for differential pressure specified on the Liquid Preferences screen Note If you select Undefined 0 0 0 for the I O definition you can manually enter a value in the Value field Otherwise the program displays the value for the currently selected input Configuration 23 Liquid Allocation Program for Continuous Flow User Manual Field Meter Temperature Input Meter Pressure Input S amp W Input Units Type of Flow Meter Input Low Flow Cutoff 24 Configuration Description Sets the source for the flowing temperature of the liquid meter Click to display the Select TLP screen and specify the TLP selection The units are the temperature units selected on the Liquid Preferences screen Note If you select Undefined 0 0 0 for the I O definition you can manually enter a value in the Value field Otherwise the program displays the value for the cur
4. Update Goce gt ERRE iita Figure 20 c Liquid Meters Flow Totalizers tab Meter Type is Orifice 34 Configuration Rev July 15 Liquid Allocation Program for Continuous Flow User Manual 2 Review and change as necessary the values in the following fields Field Indicated Volume Total Indicated Mass Total Gross Volume Total Gross Standard Volume Total Net Standard Volume Total Rev July 15 Description This read only field shows the indicated volume IV flow totalizer The units are the volume units selected on the Liquid Preferences screen Note This field only displays when the Meter Type field on the General tab is set to Linear and the Units Type of Flow Meter Input field on the Inputs tab is set to Volume This read only field shows the indicated mass IM flow totalizer The units are the mass units selected on the Liquid Preferences screen Note This field only displays when the Meter Type field on the General tab is set to Linear and the Units Type of Flow Meter Input field on the Inputs tab is set to Mass This read only field shows the current gross volume GV flow totalizer If the Meter Type field on the General tab is set to Linear and the Units Type of Flow Meter Input field on the Inputs tab is set to Volume the program calculates this value by multiplying the indicated volume IV flow by the meter factor MF The result is added to the totalizer once a s
5. 0 0 0 0 If a K Factor Curve Single Meter Factor has Factor 11 Frequency been selected parameter 42 2 this parameter is the frequency in Hz that corresponds with the associated K Factor lf a Meter Factor Curve Single K Factor has been selected parameter 42 1 this parameter is the indicated flowrate that corresponds to the associated meter factor 65 Meter Factor 12 K Factor 12 R W FL 4 gt 0 0 1 0 If a K Factor Curve Single Meter Factor has been selected parameter 42 2 this parameter is the meter constant K Factor in pulses unit of flow input for the associated frequency in Hz If a Meter Factor Curve Single K Factor has been selected parameter 42 1 this parameter is the dimensionless meter factor MF for the associated indicated flowrate 82 Reference Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name 66 Meter Factor 12 Flowrate K Factor 12 Frequency 67 S amp W Flowrate 68 S amp W Volume Total 69 Indicated Flow Today 70 Gross Volume Today 71 Gross Standard Volume Today Rev July 15 Access R W R O R O R O R O Data Length Range Type FL 4 gt 0 0 FL 4 gt 0 0 FL 4 gt 0 0 FL 4 gt 0 0 FL 4 gt 0 0 FL 4 gt 0 0 Reference Default 0 0 Description If a K Factor Curve Single Meter Factor has been selected parameter 42 2 this par
6. Note This field only displays when the Density Option on the Inputs tab is set to one of the selections for calculating the base from the observed density Base Density This read only field shows the source of the base Density density value Valid values are Equal to Base of Sources Product or Calculated from Observed Flowing Density This read only field shows the source of the flowing Density density value Valid values are Calculated from Base Sources or Equal to Observed Observed This read only field shows the density interface point Density for the observed density Density ee l Sources Note This field only displays when the Density Option on the Inputs tab is set to one of the selections for calculating the base from the observed density 38 Configuration Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Field Description Tables Used for This read only field shows the correction standards Correction also referred to as table used in calculating the Factor flowing density and if specified base density of the liquid Tables Used for Temperature This read only field shows the Correction Table temperature correction standard Factor also referred to as table used in continued calculating the flowing density and if specified base density of the liquid The following are the possible entries for the field Entries followed by indicate the base density value for the tab
7. 0 2 Reference Default 0 3417773 0 0 Description Coefficient of thermal expansion used when adjusting the volume at the base temperature to the flowing temperature The units are 10 3 times the volume fraction per Deg F or Deg C depending on the selected temperature units The units of the temperature increment are specified by TLP 22 0 2 Option indicating the use of either a single K Factor or the K Factor table with interpolation between points 0 Single K Factor Single Meter Factor 1 Meter Factor Curve Single K Factor 2 K Factor Curve Single Meter Factor lf a K Factor Curve Single Meter Factor has been selected parameter 42 2 this parameter is the meter constant K Factor in pulses unit of flow input for the associated frequency in Hz If a Meter Factor Curve Single K Factor has been selected parameter 42 1 this parameter is the dimensionless meter factor MF for the associated indicated flowrate lf a K Factor Curve Single Meter Factor has been selected parameter 42 2 this parameter is the frequency in Hz that corresponds with the associated K Factor If a Meter Factor Curve Single K Factor has been selected parameter 42 1 this parameter is the indicated flowrate that corresponds to the associated meter factor lf a K Factor Curve Single Meter Factor has been selected parameter 42 2 this parameter is the meter constant K Factor in pulses unit of flow inp
8. Not used If the meter type parameter 104 is linear and the flow input is not a pulse input Not used If the meter type parameter 104 is linear and the flow input is a pulse input Time in seconds without a pulse before setting the flow rate to 0 0 130 Flowing Status R O UINT8 1 0 1 0 Current flowing status O Currently there is no flow through the meter 1 Currently there is flow through the meter 96 Reference Rev July 15 Liquid Allocation Program for Continuous Flow User Manual 4 6 Point Type 26 Density Interface Parameters Point type 26 contains the parameters for configuring the density interface points and viewing the results of the calculations There are two logicals for this point type Point Type 26 Densitometer Parameters Parm Name Access Data Type Length Range Default Description 0 Point Tag Id R W AC 10 10 ASCII characters Logical 0 Point tag identification for the density Density interface point 1 Logical 1 Density 2 1 Density Type R W UINT8 1 0 gt 3 3 Indicates the type of density input interface 0 Micro Motion or Solartron Model 7830 40 or Model 7835 45 46 47 1 Reserved 2 UGC 278 3 Analog input The units of the density input are assumed to be that specified for the observed density units a TLP 22 0 3 2 Density Input TLP R W TLP 3 TLP 0 0 0 TLP from which to retrieve the density input The input may either be a frequency from a densitometer
9. inputs Adverced Aloma Plow Rates Flow Totakzers Deonsies Dap Morth T otasirer indicated Vome Taa 1215 Bbi P Indicated Mass Taa D5 iM Gross Vohere Taat 1215 t GV V HF Gross Vohra Tout 5735047 GV GM Flowing Danity Gross Stancded Volume T otat 1202855 Eti IGSV s GV CTL CPU Gross Standmd Volume T otat GSV s GV CTL CPU Net Standard Volume Totat 1202055 Bb pSV GSV CSW Net Standard Volume Tota MSV GSV CSW Siw Vose Taat 00 Bu Stw GSV NSV SEW Vokare Total StW GSV NSV Gross Matt Totat 47211 8659 Lb GM GV Flowang Denedy Groce Matt Total 2 gt GM IM MF Pato Scan 2 Update Close Gave As fata Scan 2 Update Close ON LINE EEA Figure 20 a Liquid Meters Flow Totalizers tab Figure 20 b Liquid Meters Flow Totalizers tab Meter Type is Linear and Units Type of Flow Meter Inputis Meter Type is Linear and Units Type of Flow Meter Input is Volume Mass wa ROCLINK 800 Liquid Meters fe Edt Yew BOC Configze Meter Rities Tools Window Help Da M bs Aw hE PZ ORF Oe 2H Powe Number 1 Lig Me 1 gt Teg La Mtu 1 Gerezi inputs Advarend Alms Flow Rates Flow Totakzers Densities Dap Month Totakeers Gross Voke Totat GV GM Flowang Daniy Gross Standard Volume T otat 2 GSV GV CTL CPU Net Standard Volume Tota 2 psy GSV CSW SEW Vokana Total StW GSV NSV Gross Matt Total gt GM Savers fato Scan
10. screen to display the values for that density interface Tag Sets a unique identifier for the selected liquid density interface 4400 Configuration Rev Jly 15 Liquid Allocation Program for Continuous Flow User Manual 4 Click Apply to save any changes and proceed to Section 3 4 1 to configure the General tab Rev July 15 Configuration 45 Liquid Allocation Program for Continuous Flow User Manual 3 4 1 Liquid Density Interfaces General Tab Use this tab which displays when you access the Liquid Density Interfaces screen to configure a density interface point s type of density input and correction factor and view its observed density and alarm Statuses wat ROCLINK 800 Liquid Density Interfaces OCLINK 800 Liquid Density Interfaces pe Edt Yew BOC Confgre Meter mites Ioos t ROC Config e coos Yindeow Heb x _ Be Ek ye OC Gon gsre Meter eites Ioos iindow Heb Ms N VE SF ZOE ey 62 g Ms N ww VA FZORE oy 62 R Tag Density 21 J l E uty Tad Density St General inguss Mero Moton Corstares UGE Comtants Abn General inguds Mico Motion ceatares UGE Constants Abwns Deruty Inout Type Densty Comection Factor Dernty Inout Type Deruty Comection F acter for Sokartoory 10 ke Sodarbord 10 Macro Mahon far Soli Maro Moon PRG 60 or FER 05 46 67 FEAM ot 7 46 a Jewredtorreelen Jeruderneles UGC 278 Denstometar T Apply Hydhomete Comecton UGC 278 Denstomete Anglo Dendy kg m
11. sec and Cp Volume Units Sets the units for all volume flow rates and total values Valid selections are Bbl Mcf Km3 Gal ft3 m3 and Liter Mass Units Sets the units for all mass flow rates and totals Valid selections are Lb Kg Ton Tonne and Mlb Flow Rate Time Sets the time units for all volume and mass flow rates Units Valid selections are Per day Per hour Per minute Per second Elevation Units Sets the units for the elevation used to determine the atmospheric pressure when the latter is specified to be calculated Valid selections are Feet and Meters Base and Sets the units for the base and flowing densities Valid Flowing Density selections are Kg m3 Relative Density and API Units Gravity Observed Sets the units for the density determined by the Density Units density interface point observed density Valid selections are Kg m3 g cm3 Lb ft3 Lb bbl Lb gal Relative Density and API Gravity 4 Click Apply to save your changes and proceed to Section 3 2 to configure the Liquid Products Rev July 15 Configuration 13 Liquid Allocation Program for Continuous Flow User Manual 3 2 Liquid Products Screen Use this screen to specify up to two liquid products that could flow through the liquid meters To access this screen 1 Click User Program gt Liquid Products from the ROCLINK configuration tree 2 Double click Display 24 Liquid Products 3 Double click 1 Product 1 The following scree
12. the Alarms tab Configuration 53 Liquid Allocation Program for Continuous Flow User Manual 3 4 5 Liquid Density Interfaces Alarms Tab Use this tab to configure the observed density alarming parameters for a density interface point To access this screen 1 Select the Alarms tab on the Liquid Density Interfaces screen The following screen displays vam ROCLINK 800 Liquid Density Interfaces Eile Edit view ROC Configure Meter Utilities Tools Window Help D k G H HU hi Seon KUE Point Number 1 Density 1 v Tag Density 1 Observed Density Alarming Haa ane M200 z000 Kama C Enabled Ea Low Alarm Limit 1300 0 Kg m3 e Disabled Alarm Deadband 15 0 Kg m3 RBX On Alarm Set f On Alarm Clear Print Save As Auto Scan X Update Close gt TONSDINE 11 21AM Figure 28 Liquid Density Interfaces Alarms tab 2 Review and change as necessary the values in the following fields Field Description Observed Enables or disables alarming of the observed density Density If enabled alarm status changes are added to the Alarming Alarm Log If disabled no alarm generates for this density interface point regardless of the alarm configuration RBX Enables Report by Exception alarm messages These messages are sent via communication ports that have RBX mode enabled On Alarm Set When the observed density value enters the alarm condition the FB107 generates an RBX message s 54
13. 1 API 2540 Table 5 6B 1980 2 API 2540 Table 5 6D 1982 3 API 2540 Table 6C 1980 4 API 2540 Table 23 24A 1980 5 API 2540 Table 23 24B 1980 6 API 2540 Table 23 24D 1982 7 GPA TP 27 23 24E 2007 8 API 2540 Table 24C 1980 9 API 2540 Table 53 54A 1980 10 API 2540 Table 53 54B 1980 11 API 2540 Table 53 54D 1982 12 GPA TP 27 Table 53 54E 2007 13 API 2540 Table 54C 1980 14 IP 3 Table 59 60A 1988 15 IP 3 Table 59 60B 1988 16 IP 3 Table 59 60D 1988 17 GPA TP 27 Table 59 60E 2007 18 API 11 1 6 2004 19 API 11 1 7 2004 20 API 2540 Table 23 24A 1980 21 API 2540 Table 23 24B 1980 22 API 2540 Table 23 24D 1982 23 GPA TP 27 Table 23 24E 2007 24 API 2540 Table 24C 1980 25 API 2540 Table 53 54A 1980 26 API 2540 Table 53 54B 1980 27 API 2540 Table 53 25D 1982 28 GPA TP 27 Table 53 54E 2007 29 API 2540 Table 54C 1980 30 API 2540 Table 59 60A 1980 31 API 2540 Table 59 60B 1980 32 API 2540 Table 59 60D 1982 33 GPA TP 27 Table 59 60E 2007 34 API 11 4 1 2003 99 Invalid Table 90 Reference Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name Access Data Length Range Default Description Type 103 Pressure Correction Table R O UINT8 1 0 gt 7 99 1 Pressure correction table used to calculate the flowing densi
14. 5 Compressibility Factor R W FL 4 gt 0 0 0 349 User specified value of the compressibility F for adjusting the volume from the base to the flowing pressure This value is used only if the user entered compressibility is selected parameter 4 Is set to 3 If the base temperature is 60 Deg F Units are 10 5 times the volume fraction pressure unit If the base temperature is 15 20 or 30 Deg C Units are 10 6 times the volume fraction per pressure unit 6 Alpha Coefficient R W FL 4 gt 0 0 0 3418 User entered alpha coefficient This value is used only if the fluid type selected parameter 2 is Special Applications 2 The units are volume fraction per temperature increment The units of the temperature increment are specified by TLP 22 0 2 7 Base Density R W FL 4 gt 0 0 999 016 Density of the product at base temperature and pressure Density units are specified by TLP 22 0 10 Rev July 15 Reference 69 Liquid Allocation Program for Continuous Flow User Manual 4 5 Point Type 25 Liquid Meter Parameters Point type 25 contains the parameters for configuring the liquid meters and viewing the results of the calculations There are two logicals for this point type Point Type 25 Liquid Meter Parameters Parm Name Access Data Length Range Default Description Type 0 Point Tag Id R W AC 10 10 ASCII Logical 0 Point tag identification characters Lig Mtr 1 Logical 1 Liq Mtr 2
15. 52 3 4 5 Liquid Density Interfaces Alarms Tab ccccccccssesceeceeeeeeeeeeeeeseeeeeeneeeeeenaneeeeas 54 3 9 SaViINnG INE COMIGUT AO aena a A E E 56 4 Reference 59 4 1 Density Ranges for Liquid Product TYP S cccseccccceseeeeeceeeeeecaeeeeseeeeeeesseueeesaaseeeeneeees 60 42 VAGUIG Allocation IANS TONY ceras e cided ae eabeen Daoneas hentai vad 62 42 1 Typical History SO UID sass aati eats acs hd A ass ial el ea ale al 63 4 3 Point Type 22 Liquid Preference Parameters cccccsscccccsseeeeceseecceeseeecceuseeesaseeessaaess 65 4 4 Point Type 23 Liquid Product Parameters ccccccccccsseeeeeceeeeeeeeeeeeeseeseeesseseeeesneeessaeeees 68 4 5 Point Type 25 Liquid Meter Parameters cccccscccccesececceeseeeceseeeceauseeeceuseesssaseeeesaaees 70 4 6 Point Type 26 Density Interface Parameters cccccseeccccseeeeeeeeeseeeseeeeeessseeeesaeeeessaeees 97 Rev July 15 Contents jii Liquid Allocation Program for Continuous Flow User Manual This page is intentionally left blank IV Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Chapter 1 Introduction This chapter describes the structure of this manual and presents an overview of the Liquid Allocation Program for Continuous Flow for the FloBoss 107 FB107 1 1 Scope and Organization This document is the user manual for the Liquid Allocation Program for Continuous Flow 1LK 7
16. Analog Donaty Kom3 Observed Denaty aa tie Ko m3 Observed Denaty aa ie Ko m3 Actre Alen Nore Active Alama Hore Bit imos Asosoon hundo Dos 2 toe Bin Simoa Aaso indio Dos 2 ON LINE mE ON LINE rane Figure 24 a Liquid Density Interfaces General tab Figure 24 b Liquid Density Interfaces General tab Density Input Type is an Analog Density Density Input Type is a Frequency Densitometer 1 Review and change as necessary the values in the following fields Field Description Density Input Sets the type of density input The density value can Type be from a frequency densitometer or an analog value Valid selections include Micro Motion or Solartron 7830 40 or 7835 45 46 47 UGC 278 Densitometer and Analog Density Note The input units of a frequency densitometer are Hz The resulting density is in the units of the Observed Density specified on the Liquid Preference screen The units of an Analog Density Input value must be the units of the Observed Density specified on the Liquid Preferences screen Observed This read only field shows the calculated observed Density density of the selected density interface point The units are those for the Observed Density specified on the Liquid Preferences screen 46 Configuration Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Field Description Active Alarms This read only field shows the status of any active alarms of th
17. Configuration Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Field Description On Alarm Clear When the observed density value clears the alarm condition the FB107 generates an RBX message s High Alarm Sets the value at or above which the value of the Limit observed density must rise to generate a high alarm The units are those of the Observed Density on the Liquid Preferences screen Low Alarm Limit Sets the value at or below which the value of the observed density must fall to generate a low alarm The units are those of the Observed Density on the Liquid Preferences screen Alarm Sets a value that defines a zone above the Low Alarm Deadband Limit and below the High Alarm Limit When an alarm condition is set the value of the observed density must clear the alarm limit plus the zone defined by the deadband before the alarm condition clears This deadband prevents the system from setting and clearing the alarm continuously when the value of the observed density oscillates around the alarm limit The units are those of the Observed Density on the Liquid Preferences screen 4 Click Close to close this screen Proceed to Section 3 5 to save the configuration Rev July 15 Configuration 55 Liquid Allocation Program for Continuous Flow User Manual 3 5 Saving the Configuration 56 Whenever you modify or change the configuration it is a good practice to save the final configuration to memory
18. Density e 3 C Crude Oil The base density of water is set using the meter s base C Gasoline temperature C Jet Fuel C Fuel Oil C Lube Oil C Special Application C Light Hydrocarbon Print Save As Auto Scan Update Close Apply Oo 12 00PM Figure 12 c Liquid Products Product Definition tab Liquid Type is Water 16 Configuration Rev July 15 Liquid Allocation Program for Continuous Flow User Manual 1 Review and change as necessary the values in the following fields Field Description Liquid Type Sets the type of fluid associated with this product number Valid selections are Crude Oil Gasoline Jet Fuel Fuel Oil Lube Oil Special Application Light Hydrocarbon and Water Note See Section 4 1 for density ranges and additional information about the liquid types API Table If the Liquid Type is anything other than light hydrocarbon or water Crude Oil Gasoline Jet Fuel Fuel Oil Lube Oil or Special Application select the appropriate the API table to use for calculations Valid selections are 1980 and 2004 If the Liquid Type is light hydrocarbon this field shows that the GPA TP 27 table is being used for calculations If the Liquid Type is water this field shows that the API Table 11 4 1 2003 is being used for calculations Base Density Sets the density of the liquid product at the base temperature and base or equilibrium pressure The units are as specified by the base and flowing
19. Liquid Allocation Program for Continuous Flow User Manual 3 4 Liquid Density Interfaces Screen Use this screen to configure up to two liquid density interfaces and view the resulting calculated also called observed density values To access this screen 1 Click User Program gt Liquid Alloc from the ROCLINK configuration tree 2 Double click Display 27 Liquid Density Interfaces The Liquid Density Interfaces screen displays mam ROCLINK 800 Liquid Density Interfaces File Edit View ROC Configure Meter Utilities Tools Window Help Dw Ot k AHTa A SaO EY 2 h Point Number 1 Density 1 v Tag Density 1 General Inputs Micro Motion Constants UGC Constants Alarms Density Input Type Density Correction Factor _ Micro Motion for Solartron 11 0 C 7830 40 or 7835 45 46 47 Densitometer UGC 278 Densitometer f Apply Hydrometer Correction Observed Density 1999 016 Kg m3 Active Alarms None Print Save As Auto Scan 3 Update Close Apply gt ORRNNEI 11 524 Figure 23 Liquid Density Interfaces Screen Note Two fields at the top of the screen Point Number and Tag appear on all tabs 3 Review and change as necessary the values in the following fields Field Description Point Number Selects the liquid density interface to configure Click v to display all of the liquid density interfaces Clicking a different liquid density interface causes the
20. Pressure Volume Correction Factors for Generalized Crude Oil Refined Products and Lubricating Oils May 2004 Gas Processors Association GPA TP 27 Temperature Correction for the Volume of NGL and LPG Section 5 January 2005 API MPS Manual of Petroleum Measurement Standards Chapter 11 Physical Properties Data Section 4 Properties of Reference Materials Part 1 Density of Water and Water Volumetric Correction Factors for Water Calibration of Volumetric Provers First Edition December 2003 Meter types can be either differential or linear The calculation standard used for differential meters is ISO5167 The calculation used for linear meters is based on AGA Report No 11 Volume and mass flow rates and totals are calculated and stored for both meter types The program uses user defined point types for storing the calculated flow rates and accumulations The program s user defined point types are also the location where the configuration parameters reside The Liquid Allocation program also supports up to two liquid density interface points The liquid density interface points allow for manual density inputs density inputs from densitometers frequency inputs from a 2 Introduction Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Micro Motion or Solartron 7830 40 or 7835 45 46 47 and UGC densitometers The density value determined from the density input is referred to as the observed
21. Program for Continuous Flow User Manual 1 2 Product Overview The Liquid Allocation program allows a FB107 to interface with up to two meter runs passing liquid hydrocarbon fluids or water These meter runs are in addition to the meter runs provided by the FB107 Application Firmware The flowing densities and optionally base densities of the liquid hydrocarbon or water are calculated based on temperatures and pressures using one or more of the following standards API Standard 2540 Chapter 11 1 1980 Volume X Reaffirmed October 1993 The Institute of Petroleum Petroleum Measurement Paper No 3 October 1988 API Chapter 11 2 1 Compressibility Factors for Hydrocarbons 0 90 Degrees API Gravity Range 1st Edition August 1984 Reaffirmed May 1996 API Chapter 11 2 2 Compressibility Factors for Hydrocarbons 0 350 0 637 Relative Density 60 F 60 F and 50 F to 140 F Metering Temperature 2nd Edition October 1986 API Chapter 11 2 1M Compressibility Factors for Hydrocarbons 638 1074 Kilograms per Cubic Metre Range 1st Edition June 1984 Reaffirmed May 1996 API Chapter 11 2 2M Compressibility Factors for Hydrocarbons 350 637 Kilograms per Cubic Metre Density 15 C and 46 C to 60 C Metering Temperature 1st Edition October 1986 Reaffirmed March 1997 API MPS Manual of Petroleum Measurement Standards Chapter 11 Physical Properties Data Section 1 Temperature and
22. RBX on Set Enabled 10 Alarm Code R O BIN 0x00 Alarm statuses Bit 7 Manual mode status 0 No flow inputs for the flow calculation is a manual entry 1 At least one input for the flow calculation is a manual entry Bit 6 No flow alarm status No flow occurs when the flowrate specified by parameter 7 is 0 0 0 No flow alarm status is clear 1 No flow alarm status is set Bit 5 Reserved Bit 4 Reserved Bit 3 Reserved Bit 2 High flowrate alarm status The value of the flowrate is that specified by parameter 7 0 High flow rate alarm status is clear 1 High flow rate alarm status is set Bit 1 Reserved Bit 0 Low flowrate alarm status The value of the flowrate is that specified by parameter 7 0 Low flow rate alarm status is clear __ _1 High flow rate alarm status is set Rev July 15 Reference 71 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name Access Data Length Range Default Description Type 11 Low Alarm Flow R W FL 4 Any floating 1000 0 Value of the low flow alarm limit in the units of the point number selected flowrate for alarming see parameter 7 12 High Alarm Flow R W FL 4 Any floating 100000 0 Value of the high flow alarm limit in the units of point number the selected flowrate for alarming see parameter 7 13 Alarm Deadband R W FL 4 Any floati
23. Standard Volume Rate Description This read only field shows the current indicated volume IV flow rate The units are as specified for the volume and flow rate time units selected on the Liquid Preferences screen Note This field only displays when the Meter Type field on the General tab is set to Linear and the Units Type of Flow Meter Input field on the Inputs tab is set to Volume This read only field shows the current indicated mass IM flow rate The units are as specified for the mass and flow rate time units selected on the Liquid Preferences screen Note This field only displays when the Meter Type field on the General tab is set to Linear and the Units Type of Flow Meter Input field on the Inputs tab is set to Mass This read only field shows the current gross volume GV flow rate If the Meter Type field on the General tab is set to Linear and the Units Type of Flow Meter Input field on the Inputs tab is set to Volume the program calculates this value by multiplying the indicated volume IV rate by the meter factor MF If the Meter Type field on the General tab is set to Linear and the Units Type of Flow Meter Input field on the Inputs tab is set to Mass or if the Meter Type field is set to Orifice he program calculates this value by dividing the gross mass GM flow rate by the flowing density The units are the volume and flow rate time units selected on the Liquid Preferences screen This read only
24. The program and license key can be installed in any order The manual shows the installation of the license key first 2 1 Installing the License Key A license key 1LK 7 is required to use the Liquid Allocation program To install a USB key based license on the FB107 1 Insert the USB license key in a USB port on your PC 2 Select Utilities gt License Key Administrator gt Transfer Between Device and Key from the ROCLINK 800 menu bar The Transfer Licenses Between a Device and a Key screen displays Transfer Licenses Between a DEVICE and a KEY Licenses on DEVICE A Application Name App Code Cuaritity Expiration Time Created Connect to KEY Move to KEY Add License Remove Licenses on KEY Time Created Application Name Vendor ID Yerndor Hame App Code Version Expiration 0572872009 11 11 06 AM Liquid Alloc 31529 RAS 1 0 0 No Expiration i i fr2aa56789 License Key Event Lo Serial Number E Time Stamp Yendor 1D Application Name Previous Quantity New Quantity Figure 1 Transfer Licenses Between a Device and a Key Rev July 15 Installation 5 Liquid Allocation Program for Continuous Flow User Manual Note This screen has three sections The upper portion Licenses on Device shows any software licenses installed on the FB107 The middle portion Licenses on Key shows software licenses on the license key The lower portion of the screen License Key Event Log provides a rolling log of the last eight events
25. To download the user program 1 Start and logon to ROCLINK 800 2 Select ROC gt Direct Connect to connect to the FloBoss unit 3 Select Utilities gt User Program Administrator from the ROCLINK menu bar The User Program Administrator screen displays see Figure 3 User Program Administrator User Programs Installed in Device Mame No Program Ho Program Ho Program Version Library Version Mo Prograrn No Program Created DAAM Used 0 Ho Prograrn CALC FLASH Used 0 Entry Pt Displays Cea S Stop Status Empty Download User Program File Browse Name Version Created CRC Size eN Update Close Figure 3 User Program Administrator 4 Click Browse in the Download User Program File frame The Select User Program File screen displays see Figure 4 5 Select the path and user program file to download from the CD ROM Program files are typically located in the Program Files folder on the CD ROM As Figure 4 shows the screen lists all valid user program files with the BIN extension Rev July 15 Installation 7 L iquid Allocation Program for Continuous Flow User Manual Select User Program File Look in Program Files LiquidAlloc_1 bin My Documents qs My Computer File name on Files of type Liquid Alloc_1 bin User Programs bin Cancel Figure 4 Select User Program File 6 Click Open to select the prog
26. are specified by TLP 22 0 6 and the time units are specified by TLP 22 0 8 If the meter type parameter 104 is linear and the type of units of the liquid meter flow input parameter 3 is mass Indicated mass flowrate through the meter This value matches that of the indicated flowrate parameter 27 The mass units are specified by TLP 22 0 7 and the time units are specified by TLP 22 0 8 If the liquid meter type parameter 104 is orifice this value is before the low differential flow cutoff is applied sqrt hw The units are sqrt of the units specified by TLP 22 0 0 94 CSW R O FL 4 gt 0 0 1 0 The correction factor due to non merchantable quantities such as sediment and water It is one 1 minus the volumetric fraction of merchantable quantities in the liquid 95 Combined Correction Factor R O FL 4 gt 0 0 1 0 The combined correction factor for adjusting the CTPL When Determining the volumetric flow from the base temperature and Flowing Density pressure to the flowing temperature and pressure CTPL CTL CPL Rev July 15 Reference 87 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm 96 97 99 100 88 Name Correction for Temperature of the Liquid CTL When Determining the Base Density Correction for Pressure of the Liquid CPL When Determining the Base Density Compressibility Factor F When Determini
27. density The base density of the liquid hydrocarbon passing through a meter can be specified to be calculated from the observed density 1 3 Program Requirements You download the Liquid Allocation program to and then run it from the Flash and RAM memory on the FB107 with firmware version 1 30 or greater Because the program is larger than 64K it occupies two user C program numbers 1 amp 2 Download and configure the program using ROCLINK 800 Configuration software version 1 84 or greater The downloadable program 1s File Name Target Unit User Defined Flash Used DRAM Used ROCLINK 800 Display Version Points UDP in bytes in bytes Version Number Baie bin FB107 1 30 22 23 25 26 94 560 32 768 1 84 23 24 26 27 FB107 ee Lil 22 23 25 26 94 560 32 768 1 84 23 24 26 27 1 00 Note You must connect a PC to the FloBoss s LOI port before starting CON e a a For information on viewing the memory allocation of user programs refer to the ROCLINK 800 Configuration Software User Manual for FB107 Form A6217 Rev July 15 Introduction 3 Liquid Allocation Program for Continuous Flow User Manual This page is intentionally left blank 4 Introduction Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Chapter 2 Installation This section provides instructions for installing the Liquid Allocation program into the FB107 Read Section 1 3 of this manual for program requirements Note
28. lf a Meter Factor Curve Single K Factor has been selected parameter 42 1 this parameter is the indicated flowrate that corresponds to the associated meter factor 49 Meter Factor 4 K Factor 4 R W FL 4 gt 0 0 1 0 If a K Factor Curve Single Meter Factor has been selected parameter 42 2 this parameter is the meter constant K Factor in pulses unit of flow input for the associated frequency in Hz If a Meter Factor Curve Single K Factor has been selected parameter 42 1 this parameter is the dimensionless meter factor MF for the associated indicated flowrate 78 Reference Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name Access Data Length Range Default Description Type 50 Meter Factor 4 Flowrate K R W FL 4 gt 0 0 0 0 If a K Factor Curve Single Meter Factor has Factor 4 Frequency been selected parameter 42 2 this parameter is the frequency in Hz that corresponds with the associated K Factor lf a Meter Factor Curve Single K Factor has been selected parameter 42 1 this parameter is the indicated flowrate that corresponds to the associated meter factor 51 Meter Factor 5 K Factor 5 R W FL 4 gt 0 0 1 0 If a K Factor Curve Single Meter Factor has been selected parameter 42 2 this parameter is the meter constant K Factor in pulses unit of flow input for the associated frequency in Hz If a Meter Fact
29. orifice 26 Configuration Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Field Description K Factor Sets the linear meter constant K factor value used for this meter The units are in Pulse Unit Volume or Pulse Unit Mass and must match the units selected for the volume or mass on the Liquid Preferences screen Notes This field can only be set if you select Single MF Single K factor or MF Curve Single K factor in the Meter Factor K factor Options field This field only displays when the meter type is linear Meter Factor Sets the meter factor obtained by dividing the quantity of fluid the proving system measured by the quantity the meter indicates during proving for the liquid meter Notes This field can only be set if you select Single MF Single K factor or K factor Curve Single MF from the Meter Factor K factor Options field This field only displays when the meter type is linear Meter Factor K Sets the option to use when calculating K factors or Factor Options meter factors Valid selections are Note This field only displays when the meter type is linear Single MF Uses a single meter factor and a Single K factor single K factor for the liquid meter These values are set in the K factor and Meter Factor fields MF Curve Uses a series of meter factor curve Single K factor values and a single K factor Specify up to 12 meter facto
30. related to this license key 3 Select the key based license you want to transfer to the FB107 Liquid Alloc as shown in Figure 1 4 Click Move to Device ROCLINK moves one instance of the license from the key to the FB107 and updates the screen Transfer Licenses Between a DEVICE and a KEY Licenses on DEVICE Application Mame Vendor Name App Code Version Quantity License Source Expiration Time Created 1 Liquid Alloc RAS 1 00 0 1 Key No Expiration 05 26 2009 11 11 06 AM Connect to KEY Move to DEVICE Add License Remove Licenses on EEY _ Time Created Application Name Vendor ID i 17125456789 License Key Event Log Serial Number 31529 Liquid Alloc Figure 2 License Installed Note An FB107 can hold up to six different licenses although you can install only one instance of each license on the FB107 When you click Move to Device ROCLINK 800 moves only one instance of the license onto the FB107 and automatically decreases the license quantity on the USB key by one 5 Verify the license name displays in the Licenses on Device section of the screen Proceed to Section 2 2 to download the user program 6 Installation Rev July 15 Liquid Allocation Program for Continuous Flow User Manual 2 2 Downloading the Program This section provides instructions for installing the user program into FloBoss memory Note Connect a PC to the FloBoss s LOI port before starting the download
31. s Tonne C API Gravity PAE C mmH20 Flow Rate Time Units Diaea Unte c Pa tour C millimeter r i se Viscosity Units fe Witter Elevation Units Cp Feet C Meter Print Save As Auto Scan Update Close a TONSDINE 8 46AM Figure 10 Liquid Preferences Screen 3 Review the values in the following fields Field Description Program Status This read only field shows the current status for the Liquid Allocation program Possible statuses are Program Running and License Not Found you must install a Liquid Alloc license key to use the program Temperature Sets the units of all temperature inputs Valid Units selections are Deg F and Deg C Pressure Units Sets the units of all pressure inputs Valid selections are Psi kPa Bar and Kg cm2 12 Configuration Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Field Description Units for Orifice The following units are applicable if the meter type of a Meters liquid meter is specified as orifice in which case ISO 5167 2003 is used as the flow calculation standard Diff Press Units Sets the units of the differential flow input Valid selections are InNH2O0 kPa mBar and mmH20O Units of INH20 and mmH20 are based on a water temperature of 60 Deg F Diameter Units Sets the units for the meter and pipe orifice diameters Valid selections are Inch and millimeter Viscosity Units Sets the units for the viscosity of the fluid Valid selections are Lb ft
32. screen 1 Select the Densities tab on the Liquid Meters screen One of the following two screens displays wa ROCLINK 800 Liquid Meters wae ROCLINK 500 Liquid Meters Fle Edt Yew AOC Configure Meter ities Tools Window Help Fle Edt View AOC Configure Meter tities Tools Window Hep Og Gh bs NTa ME PFSZORZTF AR 2H Og Gt b Aw ME PFS ORF A 2H Port Number 1 Lig Me 1 Tog liq Me 1 Point Number 1 Lig Me 11 Tog lq Me 1 Geresa inputs bavereed Aleem Flow Rates Flow Totakrers Dernis Dap Merth otakrers Gerezi inputs Adverced Aleem Fio Rates Flow Totakrers Deriiet Dap Merth otakrers Connection Factors Deraty Vokes Deraty Source Conection Factors Deraty Vokes Deraty Sources CTL 0 9097131 Bate Dentty Base Deraty CTL 0 906974 Bate Denny Base Deraty laan T CA f 001 1339 0 Kong Equa to Hate of Product 1 Produet 31 ce Moy 855 9911 Kyi Calculated thom Oberewed Flowing Density Flowery Denny CTPL 09862 Flowing Density Flower Denny Alpha 03417772 10 3x Vol Feac DegF 9883085 Kgym3 Calculated From Base Alpha 04655164 10 3xVolFeac DegF uN Koi Calculated From Base CTP 03839 F 03763203 10 S x Vol Froc PS F 05415335 10 S x Vol Froc PS f Odterved Dentity Obverved Density CSW Fatter 10 CSW Factor 10 a0 Kom Fromm Dewvaty rtectace 1 Dernaty t1 T ables Used for Corector Factors T ables Used for Corector Factors Tempetatuen Tabie Tempetatuen able API Pro
33. screen to configure up to two liquid meter runs and observe the calculated values To access this screen 1 Click User Program gt Liquid Alloc from the ROCLINK configuration tree 2 Double click Display 26 Liquid Meters The Liquid Meters screen displays vem ROCLINK 800 Liquid Meters Eile Edit view ROC Configure Meter Utilities Tools Window Help Dw Gt Whew htt SONR He R Point Number Tag Liq Mtr 1 General Inputs Advanced Alarms Flow Rates Flow T otalizers Densities Day Month Totalizers Meter Description Product Selection Product 1 X Meter Type Base Temperature Linear 60DegF C Orifice C 15DegC C 20DegC C 30DegC Base Vapor Pressure 0 0 PSIG Active Alarms None Print Save As Auto Scan 2 Update Close gt DREINE 10 37 AN Figure 14 Liquid Meters Screen 3 Review and change as necessary the values in the following fields Field Description Point Number Selects the liquid meter run to configure Click wv to display all of the liquid meters runs Clicking a different meter run causes the screen to display the values for that meter run Tag Sets a unique identifier for the selected liquid meter 4 Click Apply to save any changes and proceed to Section 3 3 1 to configure the General tab 20 Configuration Rev July 15 Liquid Allocation Program for Continuous Flow User Manual 3 3 1 Liquid Meters General Tab Use this tab which appears w
34. the pressure compensation calculation Otherwise Not used If the densitometer type is UGC parameter 1 is set to 2 Constant Tc from the calibration certificate of the UGC densitometer The program uses this constant in the temperature compensation calculation Otherwise Not used Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Point Type 26 Densitometer Parameters Parm Name 26 UGC Temperature Correction Constant Kt1 27 UGC Temperature Correction Constant Kt2 28 UGC Temperature Correction Constant Kt3 29 Density Correction Factor 30 Observed Density 31 Observed Relative Density 32 Observed API Gravity Default 0 0 0 0 0 0 1 0 999 012 1 0 Description If the densitometer type is UGC parameter 1 is set to 2 Constant Kt1 from the calibration certificate of the UGC densitometer The program uses this constant in the temperature compensation calculation Otherwise Not used If the densitometer type is UGC parameter 1 is set to 2 Constant Kt2 from the calibration certificate of the UGC densitometer The program uses this constant in the temperature compensation calculation Otherwise Not used If the densitometer type is UGC parameter 1 is set to 2 Constant Kt3 from the calibration certificate of the UGC densitometer The program uses this constant in the temperature compensation calculation Oth
35. the Inputs tab is set to Volume the program calculates this value by multiplying the gross volume GV flow rate by the flowing density If the Meter Type field on the General tab is set to Linear and the Units Type of Flow Meter Input field on the Inputs tab is set to Mass the program calculates this value by multiplying the indicated mass IM flow rate by the meter factor MF If the Meter Type field on the General tab is set to Orifice this value is the result of the IS05167 2003 orifice flow rate calculation 3 Click Apply to save any changes and proceed to Section 3 3 6 to view the values on the Flow Totals tab Rev July 15 Configuration 33 Liquid Allocation Program for Continuous Flow User Manual 3 3 6 Liquid Meters Flow Totalizers Tab Use this tab to view the values of a liquid meter s continuous flow totalizers Note Each totalizer value rolls over when its value exceeds 1 000 000 To access this screen 1 Select the Flow Totalizers tab on the Liquid Meter screen One of the following three screens displays wae ROCLINK 500 Liquid Meters Hi wa MOCLINK 500 Liquid Meters Fle Edt View AOC Configure Meter ities Tools Window Help o Fle Edt Wew ROC Configure Meter Utities Tools Window Help Da M NTa ME PFRZORGF AH 2H Oa M b Pork Number 1 Lig Me a Tog laMe a Pont Number 1 Lig Me 1 Gerezi Inputs Adverced Alsema Plow Rates Flow Totakners Dewi Dag Merth T otakzers Gerea
36. the selected input is displayed Note SOM AU AUOUUNUQUGUEHUQUGUERUSUGHERUGUSHERUSUGHEEOSUGAUERUSUGUERUGUOUERUGUGUERUGUGRORUGUGRERUGUGUERUGUGRERUGUONERUGUONERUGUONOGEUSUNEEUSUORERUSUOGUCHUSUONERUGUGUERUGUONEQUGUONERUGUONERUGUONEOUGHONESUCGUORERUGUOREQUGUENEQUGUOREQUGUEREQUGUEREQUGHEREQUGROREQUGUEREQUORERE Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Field Description Pressure Assigns the point type logical and parameter TLP of the pressure I O value for the selected density interface point Click to display the Select TLP screen and define your TLP selection Note If you select Undefined 0 0 0 for the pressure input you can manually enter a value for the static pressure Otherwise the value of the selected input is displayed SAENEEDEREAUEDEAEEOESEAUEOESERUESESESUESESESUESESOSUESESOSUESESOSUESEROES ESOS SEUSS ERO SE ESOS SER Periodic Time This read only field shows the time between pulses in microseconds Note This field displays only if a Frequency Densitometer is selected as the Density Input Type 3 Click Apply to save any changes 4 Click Close to close this screen Proceed to Section 3 4 3 to configure the Micro Motion Constants tab Rev July 15 Configuration 49 Liquid Allocation Program for Continuous Flow User Manual 3 4 3 Liquid Density Interfaces Micro Motion Constants Tab Use this tab to configure a density interface point s constants for calculating the density
37. 0 1 0 If a K Factor Curve Single Meter Factor has been selected parameter 42 2 this parameter is the meter constant K Factor in pulses unit of flow input for the associated frequency in Hz If a Meter Factor Curve Single K Factor has been selected parameter 42 1 this parameter is the dimensionless meter factor MF for the associated indicated flowrate Rev July 15 Reference 81 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name Access Data Length Range Default Description Type 62 Meter Factor 10 Flowrate K R W FL 4 gt 0 0 0 0 If a K Factor Curve Single Meter Factor has Factor 10 Frequency been selected parameter 42 2 this parameter is the frequency in Hz that corresponds with the associated K Factor lf a Meter Factor Curve Single K Factor has been selected parameter 42 1 this parameter is the indicated flowrate that corresponds to the associated meter factor 63 Meter Factor 11 K Factor 11 R W FL 4 gt 0 0 1 0 If a K Factor Curve Single Meter Factor has been selected parameter 42 2 this parameter is the meter constant K Factor in pulses unit of flow input for the associated frequency in Hz If a Meter Factor Curve Single K Factor has been selected parameter 42 1 this parameter is the dimensionless meter factor MF for the associated indicated flowrate 64 Meter Factor 11 Flowrate K R W FL 4 gt
38. 22 0 6 Yesterday s total volume flow at base conditions The volume units are specified by TLP 22 0 6 Yesterday s total volume flow at base conditions minus the non merchantable quantities The volume units are specified by TLP 22 0 6 Yesterday s total volume flow of non merchantable quantities The volume units are specified by TLP 22 0 6 Yesterday s total mass flow The mass units are specified by TLP 22 0 7 Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name Access Data Length Range Default Description Type 81 Indicated Flow This Month R O FL 4 gt 0 0 0 0 Total so far this month of the indicated flow If the meter type parameter 104 is linear and the type of units of the liquid meter flow input parameter 3 is volume This month s total of the indicated volume flow The volume units are specified by TLP 22 0 6 If the meter type parameter 104 is linear and the type of units of the liquid meter flow input parameter 3 is mass This month s total of the indicated mass flow The mass units are specified by TLP 22 0 7 If the meter type parameter 104 is orifice This month s total of sqrt hw Units are sart of the units specified by TLP 22 0 0 82 Gross Volume This Month R O FL 4 gt 0 0 0 0 Total so far this month of the gross volume flow The volume units are spec
39. Aug Scan Fo Update Owe gt ORIN 11 10am Figure 22 c Liquid Meters Day Month Totalizer tab Meter Type is Orifice Rev July 15 Configuration 41 Liquid Allocation Program for Continuous Flow User Manual 2 Review and change as necessary the values in the following fields Field Description Indicated This read only field shows the indicated volume IV Volume flow totals for the current and previous days and months The units are the volume units selected on the Liquid Preferences screen Note This field only displays when the Meter Type field on the General tab is set to Linear and the Units Type of Flow Meter Input field on the Inputs tab is set to Volume Indicated Mass This read only field shows the indicated mass IM flow totals for the current and previous days and months The units are the mass units selected on the Liquid Preferences screen Note This field only displays when the Meter Type field on the General tab is set to Linear and the Units Type of Flow Meter Input field on the Inputs tab is set to Mass Gross Volume This read only field shows the gross volume GV flow totals for the current and previous days and months If the Meter Type field on the General tab is set to Linear and the Units Type of Flow Meter Input field on the Inputs tab is set to Volume the program calculates this value by multiplying the indicated volume IV by the meter factor MF and adding the re
40. E TER Figure 13 a Liquid Products Advanced tab Figure 13 b Liquid Products Advanced tab All Liquid Types and API Table 1980 or Liquid Type of Special Application and API Table 1980 GPA TP 27 except Special Application and Water wa ROCLINK BOO Liquid Products dae ROCLINK BOD Liquid Products Fle Edt Yew AOC Configure Meter Uniities Took Window Heb a Fle Edt Yew AOC Configure Meter tities Tools Window Help Oa M bs Ao ew ME FSZORZTF A 2H Oe Mb NTa WE FSZORZF HW 2K Port Number 1 Product 1 gt Prodat Tag Product 31 r Port Number 1 Product 1 bd Prodat Tag Pioda 21 Product Definition Advanced Product Definition Advanced User DefredAlha 03418 10 39 x Vol Frac Dagh heme appear on thes Lab when the selected Lad Type z Spona Apphoabon oF the cebected API T able ot 1930 Birt Savers AumScan Update Cwe Pire Savers Awgscan 2 Update Cose aew ON LINE ait Figure 13 c Liquid Products Advanced tab Figurel3 d Liquid Products Advanced tab All Liquid Types and API Table 2004 and water except Liquid Type of Special Application and API Table 2004 Special Application 18 Configuration Rev July 15 Liquid Allocation Program for Continuous Flow User Manual 2 Review and change as necessary the values in the following fields Field User Defined Alpha Compressibility Options SEAGNUESEAESUESEAESOESESSEOESEAEEOESESESSESESOESESESOSSESESOESESEHOESESSEOECER ESSEC ERRORS
41. ESO R User Defined F Description Sets the coefficient of thermal expansion alpha to use when determining the flowing density from the base density The units are 10 times the volume fraction per temperature unit the temperature units being specified on the Liquid Preferences screen Note This field only displays if the liquid type is special application Sets the option for correcting for the pressure effect when determining the flowing density from the base density Valid selections are Auto Select Compressibility Table API Chapter 11 2 1 API Chapter 11 2 2 and User Defined Compressibility Note This field only displays when the API Table is 1980 or the liquid product is light hydrocarbon Sets the compressibility F for the liquid product If the base temperature is 60 Deg F the units are 10 times the volume fraction per pressure unit If the base temperature is 15 20 or 30 Deg C the units are 10 times the volume fraction per pressure unit The pressure units are specified on the Liquid Preferences screen Note This field only displays when the compressibility option is specified as user defined compressibility 3 Click Apply to save any changes 4 Click Close to close this screen Proceed to Section 3 3 to configure the liquid meters and view the calculated values Rev July 15 Configuration 19 Liquid Allocation Program for Continuous Flow User Manual 3 3 Liquid Meters Screen Use this
42. Meter nities Tools Window Help Fle Edt View AOC Configure Meter ities Tools Window Help Og Gib Ate ME FRZORZF AH 2K Og Gt h Ate WE FZORZTF HW 2K Port Number 1 Lig Me 1 Tog liq Me 1 Powe Number 1 Lig Me 1 Tog liq Mu 1 Gereia Ingat Adverced Alarmas Fine Rates Flew otakrers Dermiies Dap Morth Totsirers 10 Deletion Values Flow Meter irgut IAJN A3 EU 14400 Sta day Meter Temperature ingut AN AS EU CI DaF Mate Presourelingt AIN ATD EU a0 PSIG SEW int Undefined 00 Und Tyne of Flow Meter eget Denaty Opera Vokme Set baie equal to product s base Mass Caloudate flovang trom base Caledete base hom oberved cakadate foveng hom base m Ualeudsle base kom obeerved tal Gowang equal lo observed Pree _ Savers fate Scan 2 Update E p J DEERE 1050 Figure 16 a Liquid Meters Inputs tab Meter Type is Linear Geral Ings Adverced Alema Flow Rates Flow Totakzers Derne DapMonih Totakzers Flow Moter iret LAJN AS EU Meter Temperature rout NAS EU Mate Pietie irgut AN ATD EU SEW Ingat Undefined Pipe Diameter f8 07 Orifice Diameter 40 Low Flow Cutolt 11 0 Presaase Tap Vaht iHi20 DeF PG Densty Opera Set bave equal to product s base Calouate flonang hom base Calerdsle base hom oberved Caltuiate fovang hom base Calerdsle bose from obeerved tal foweng equal lo observed Gouge Aloka Savers Awgscan
43. P 22 0 7 37 Correction for Temperature of R O FL 4 gt 0 0 1 0 Factor for adjusting the base density to the the Liquid CTL flowing density due to difference between the base and flowing temperatures 38 Correction for Pressure of the R O FL 4 gt 0 0 1 0 Factor for adjusting the base density to the Liquid CPL flowing density due to the difference between the base or equilibrium pressure and the flowing pressure 39 Combined Correction Factor R O FL 4 gt 0 0 1 0 CTL x CPL x Meter Factor CCF 40 Compressibility Factor F R O FL 4 gt 0 0 0 3494896 Compressibility factor of the liquid when adjusting the volume at the base or equilibrium pressure to the flowing pressure If the base temperature is 60 Deg F the units are 10 5 times the volume fraction per pressure unit If the base temperature is 15 20 or 30 Deg C the units are 10 6 times the volume fraction per pressure unit The pressure units are specified by TLP 22 0 1 76 Reference Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm 41 42 43 44 45 Rev July 15 Name Alpha for Base to Flowing Temperature Meter Factor K Factor Option Meter Factor 1 Flowrate K Factor 1 Frequency Meter Factor 1 K Factor 1 Meter Factor 2 K Factor 2 Access R O R W R W R W R W Data Type FL UINT8 FL FL FL Length
44. Part D301648X012 July 2015 Liquid Allocation Program for Continuous Flow for FloBoss 107 Flow Managers User Manual S Remote Automation Solutions EMERSON Liquid Allocation Program for Continuous Flow User Manual Revision Tracking Sheet July 2015 This manual may be revised periodically to incorporate new or updated information The revision date of each page appears at the bottom of the page opposite the page number A change in revision date to any page also changes the date of the manual that appears on the front cover Listed below is the revision date of each page if applicable Page Revision All pages July 15 All pages May 11 Initial release Sep 09 i Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Contents Page Chapter 1 Introduction 1 TAi Scope and Organizators had eeesecee si a ead a e e 1 12 Produ tT OVErVIEW on eino a a e a a aati 2 to Program ReguremenlS siisi seicr reenen aae E 3 Chapter 2 Installation 5 24 AMStaliniG Tae License Wey viessaveus acetoacetate ele eee toed elena a 5 22 OOWMOAGING the Progra cosciensa a a dams catelhumana edt aa di 7 Chapter 3 Configuration 11 Sul LIGUIG PFEIETENGES Screener a aa a a 12 32 LIQUIG Products SCNECMN sson a aia hie eaelacee 14 3 2 1 Liquid Products Product Definition Tab ccccceeeecsseeeeeeseeeeeseeeeeeeseeeeeeeneeeeas 16 3 2 2 Liquid Products Advanced Tab ccccccecccccccsseseeeeeeeees
45. Standard Volume Rae 1370010 NSV GSV CSW Stw VohneRoe 00 BbVday St GSV NSV Stw Vome Rae ao tw GSV NSV Gross Matt Raia 4991317 Lividay GM GV Flowang Density Gross Mate ale 14200000 GM IM MFJ Birt Savers Augscan 2 Update Chore Pie Savers Augscan 2 Updwe Crore DEMNE 1 01 Am Figure 19 a Liquid Meters Flow Rates tab Figure 19 b Liquid Meters Flow Rates tab Meter Type is Linear and Units Type of Flow Meter Input is Meter Type is Linear and Units Type of Flow Meter Input is Volume Mass wae ROCLINK 800 Liquid Meters Z Ele Edt View BOC Configuze Meter Rites Tools Window Hep Da i M b NTa hE PSZORF UE 2H Pora Number 1 Liq Me 1 hd Teg Lx Me 1 Gerezi inputs Advanced Alms Flow Rates Flew Totaizers Densities Dap itorth Totakeees Giot Vome Rae Pasos GV GM Flowing Density Gross Standud Volume Rate 2 i GSV GV CTL CPL Net Standard Vokume Rae 2 MSV GSV CSW Siw Vome Rae 00 i tw GSV NSV Gross Matt Rate GM Pret Savers l Aug Scan 2 Update Chose URRE iita Figure 19 c Liquid Meters Flow Rates tab Meter Type is Orifice Rev July 15 Configuration 31 Liquid Allocation Program for Continuous Flow User Manual 2 Review and change as necessary the values in the following fields Field Indicated Volume Rate Indicated Mass Rate Gross Volume Rate Gross Standard Volume Rate Net
46. To save the configuration 1 Select ROC gt Flags The Flags screen displays Restart Flash Memor wam Start Save Configuration Cold Start Cold Start amp Clear Alarms E vents Status gt Cold Start amp Clear Displays Cold Start amp Clear FST Cold Start amp Clear History Cold Start amp Clear ALL 2 Update Y Ok 7 Cancel Figure 29 Flags 2 Click Save Configuration A verification message displays ROCLINK 800 P Perform Flash Memory Save Configuration Figure 30 Save Verification Configuration Rev July 15 Liquid Allocation Program for Continuous Flow User Manual 3 Click Yes When the save process completes a confirmation message displays ROCLINK 800 Figure 31 Confirmation Note Depending on the size and complexity of the user program this process may take several minutes When the process ends the Status field on the Flags screen displays Completed 4 Click Update on the Flags screen This completes the process of saving your new configuration Note For archive purposes you should also save this configuration to your PC s hard drive or a removable media such as a diskette or a flash drive using the File gt Save Configuration option on the ROCLINK 800 menu bar Rev July 15 Configuration 57 Liquid Allocation Program for Continuous Flow User Manual This page is intentionally left blank 58 Configuration Rev July 15 Liqui
47. ad only field shows the sediment and water S amp W flow totals for the current and previous days and months The program calculates these values by adding the net standard volume NSV flow minus the gross standard volume GSV flow to the totalizers once a second The units are the volume units selected on the Liquid Preferences screen Gross Mass This read only field shows the gross mass GM flow totals for the current and previous days and months If the Meter Type field on the General tab is set to Linear and the Units Type of Flow Meter Input field on the Inputs tab is set to Volume the values are calculated by adding the gross volume GV flow multiplied by the flowing density to the totalizers once a second If the Meter Type field on the General tab is set to Linear and the Units Type of Flow Meter Input field on the Inputs tab is set to Mass the values are calculated by adding the indicated mass IM flow multiplied by the meter factor MF to the totalizers once a second If the Meter Type field on the General tab is set to Orifice the values are calculated by integrating the result of the 1505167 2003 orifice flow rate calculation once a second The units are the mass units selected on the Liquid Preferences screen 3 Click Apply to save any changes 4 Click Close to close this screen Proceed to Section 3 4 to configure the liquid density interfaces and view the calculated values Rev July 15 Configuration 43
48. alculations are based on AGA Report No 11 Orifice meter calculations are based on ISO5167 Rev July 15 Configuration 21 Liquid Allocation Program for Continuous Flow User Manual Field Description Base Sets the base temperature to which volume flows are Temperature adjusted for the liquid meter Valid selections are 60 Deg F 15 Deg C 20 Deg C and 30 Deg C Base Vapor Sets the base pressure to which volume flows are Pressure adjusted for the liquid meter The pressure units are specified on the Liquid Preferences screen This read only field shows the status of any active alarms associated with this meter Possible alarms are Low High No Flow and Manual Active Alarms Notes A Manual alarm means one or more of the density temperature or pressure I O definitions on the Inputs tab is Undefined You define these alarms on the Alarms tab 2 Click Apply to save any changes and proceed to Section 3 3 2 to configure the Inputs tab 22 Configuration Rev July 15 Liquid Allocation Program for Continuous Flow User Manual 3 3 2 Liquid Meters Inputs Tab Use this tab to configure the inputs for a liquid meter and the source for the base density of the fluid passing through the meter To access this screen 1 Select the Inputs tab on the Liquid Meters screen One of the following two screens displays dae ROCLINK BOO Liquid Meters dae ROOLINK GOO Liquid Meters Fle Edt View AOC Configure
49. ameter is the frequency in Hz that corresponds with the associated K Factor lf a Meter Factor Curve Single K Factor has been selected parameter 42 1 this parameter is the indicated flowrate that corresponds to the associated meter factor Volume flowrate of non merchantable quantities such as sediment and water The volume units are specified by TLP 22 0 6 and the time units are specified by TLP 22 0 8 Continuous totalizer of the volume flow of non merchantable quantities such as sediment and water The value rolls over when it exceeds 1000000 0 The volume units are specified by TLP 22 0 6 Total so far today of the indicated flow lf the type of units of the liquid meter flow input parameter 3 is volume Total so far today of the indicated volume The volume units are specified by TLP 22 0 6 If the type of units of the liquid meter flow input parameter 3 is mass Total so far today of the indicated mass The mass units are specified by TLP 22 0 7 If the meter type parameter 104 is orifice Total so far today of sart hw Units are sart of the units specified by TLP 22 0 0 Total so far today of the gross volume flow The volume units are specified by TLP 22 0 6 Total so far today of the volume flow at base conditions The volume units are specified by TLP 22 0 6 83 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name 72 Ne
50. ameters for the Liquid Allocation Program point types are added they will not be correctly calculated as a flow weighted average 62 Reference Rev July 15 Liquid Allocation Program for Continuous Flow User Manual 4 2 1 Typical History Setup A typical configuration for the history setup for the first Liquid Allocation Program meter is shown below Note The Archive Type implies that a linear average 1s being recorded however the program overrides this selection and stores a flow weighted average which is displayed when the daily or hourly history is retrieved History Setup 1 Ava Linear 26 0 6 Cbs Temp L Mtr Temp Avg Linear 26 0 8 Obs Press 25 0 24 Mtr Press Mtr Factor Avg Linear 26 0 3 b Dens 25 0 13 Base Dens g 25 0 18 Mtr Dens 9 Undefined 000 oo 10 Undefined 000 o 11 Undefined 00o ooo 12 13 Undefined 000 S 14 Undefined 15 Undefined 16 Undefined OOO S 17 Undefined 18 Undefined 0 19 Undefined 20 Undefined OOO S 21 Undefined 2 Update y OK A Cancel Apply Figure 32 Typical History Setup Rev July 15 Reference 63 Liquid Allocation Program for Continuous Flow User Manual This page is intentionally left blank 64 Reference Rev July 15 Liquid Allocation Program for Continuous Flow User Manual 4 3 Point Type 22 Liquid Preference Parameters Point type 22 contains the parameters for configuring the units and viewing
51. ansion Alpha is 230 0 x 10 to 930 0 x 10 volume fraction per Deg F 414 0 x 10 to 1674 0 x 10 volume fraction per Deg C Light Hydrocarbon Includes LPG and NGL Table Version Base Density Range Kg m3 Base Density Range API Gravity TP 27 350 690 70 275 Note A LPG Liquified Petroleum Gas or NGL Natural Gas Liquid comprised of predominately propane and butane should be considered a Light Hydrocarbon provided its base density lies within the range for Light Hydrocarbon Otherwise it should be considered a Crude Oil Table Version Temperature Range deg F Density at 60 deg C API 11 4 1 2003 33 104 999 016 kg m3 Rev July 15 Reference 61 Liquid Allocation Program for Continuous Flow User Manual 4 2 Liquid Allocation History For many liquid measurement use cases it is desirable to calculate hourly and daily flow weighted averages for the process variables such as temperature pressure and density The Liquid Allocation Program can be used to archive weighted averages in history for a limited set of liquid meter values When these parameters are configured in the FB107 standard history the program overrides the typical firmware history mechanism The program calculates the flow weighted average using the indicated volume The program performs weighted averages regardless of the archive type you select on the History Setup screen The following parameters are supported for this feature Note If additional par
52. as necessary the values in the following fields Field Description Alarming Option Sets the parameter whose value is to be used for alarming Valid selections include Disabled Alarm on Indicated Volume Rate Alarm on Gross Volume Rate Alarm on Gross Standard Volume Rate Alarm on Net Standard Volume Rate and Alarm on Mass Rate RBX Enables Report by Exception RBX alarm messages These messages are sent via communication ports that have RBX mode enabled On Alarm Set When the value of the parameter for alarming enters the alarm condition the FB107 generates an RBX message s Rev July 15 Configuration 29 Liquid Allocation Program for Continuous Flow User Manual Field Description for alarming clears the alarm condition the FB107 generates an RBX message s High Alarm Sets the value at or above which the value of the Limit parameter for alarming must rise to generate a high alarm The units are based on the selected Alarming Option Low Alarm Limit Sets the value at or below which the value of the parameter for alarming must fall to generate a low alarm The units are based on the selected Alarming Option Alarm Sets a value that defines a zone above the Low Alarm Deadband Limit and below the High Alarm Limit When an alarm condition is set the value of the alarming parameter must clear the alarm limit plus the zone defined by the deadband before the alarm condition clears This deadband prevents the system from set
53. ber Solartron parameter 1 is set to 0 Constant K19 from the calibration certificate of the Micro Motion or Solartron densitometer The program uses this constant in the temperature compensation calculation Otherwise Not used 14 Micro Motion Pressure Correction R W FL 4 Any floating point 0 0 If the densitometer type is Micro Motion or Constant K20A number Solartron parameter 1 is set to 0 Constant K20A from the calibration certificate of the Micro Motion or Solartron densitometer The program uses this constant in the pressure compensation calculation Otherwise Rev July 15 Reference 99 Liquid Allocation Program for Continuous Flow User Manual Point Type 26 Densitometer Parameters Parm Name Access Data Type Length Range Default Description 15 Micro Motion Pressure Correction R W FL 4 Any floating point 0 0 If the densitometer type is Micro Motion or Constant K20B number Solartron parameter 1 is set to 0 Constant K20B from the calibration certificate of the Micro Motion or Solartron densitometer The program uses this constant in the pressure compensation calculation Otherwise Not used 16 Micro Motion Pressure Correction R W FL 4 Any floating point 0 0 If the densitometer type is Micro Motion or Constant K21A number Solartron parameter 1 is set to 0 Constant K21A from the calibration certificate of the Micro Motion or Solartron densitometer The program uses this consta
54. ccess Data Length Range Default Description Type 0 Point Tag Id R W AC 10 10 ASCII Logical 0 Point tag identification for the product characters Product 1 Logical 1 Product 2 1 Liquid Type R W UINT8 1 0 9 0 Indicates the type of liquid for this product 0 Crude Oil 1 Gasoline 2 Jet Fuel 3 Fuel Oil 4 Lube Oil 5 Special Application User Entered Alpha 6 Light Hydrocarbon 7 Water 8 Used Internally for Transition 9 Invalid Product 2 API Standard Version R W UINT8 1 1 2 2 Indicates the version of the API MPMS Chapter 11 1 standard to use 1 1980 2 2004 3 Light Hydrocarbon Standard R W UINT8 1 3 3 Indicates the standard to use to calculate the Version temperature correction factor for light hydrocarbons 3 GPA TP 27 68 Reference Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Point Type 23 Liquid Product Parameters Parm Name Access Data Length Range Default Description Type 4 Compressibility Option R W UINT8 1 0 gt 3 0 Indicates the method to use for calculating the product s compressibility 0 Program determines the method based on the density of the product and units of the base temperature 1 API 11 2 1 or API 11 2 1 M calculation 2 API 11 2 2 or API 11 2 2 M calculation 3 User entered compressibility This selection is only valid if the 1980 version of the API MPMS Chapter 11 1 standard is selected parameter 2 is set to 1
55. ceckee 11 16 2004 API Proceckee 11 16 2004 Poectiae Tabia Poectiae Tabie API Table 2004 AP Table 2004 __ Bm freA Aug Scan o Update _ Coe fj As fatg Scan Fo Update ae ee Figure 21 a Liquid Meters Densities tab Figure 21 b Liquid Meters Densities tab Base Density Source is Product Base Density Source is Density Interface 2 Review and change as necessary the values in the following fields Field Description CTL This read only field shows the correction factor for the temperature of the liquid when calculating the flowing density from the base density The value is updated each main calculation period mcp which is one minute using the average temperature during the mcp CPL This read only field shows the correction factor for the pressure of the liquid when calculating the flowing density from the base density The value is updated each main calculation period mcp which is one minute using the average pressure during the mcp CTPL This read only field shows the correction factor for the temperature and pressure of the liquid when calculating the flowing density from the base density It is calculated as CTL CPL Rev July 15 Configuration 37 Liquid Allocation Program for Continuous Flow User Manual Field Description Alpha This read only field shows the coefficient of thermal expansion of the liquid when adjusting the volume from the base to the flowing temperature The un
56. culate base from observed options in the Density Options field Pressure Tap Sets the reference for the meter s flowing pressure valid selections are Gauge and Absolute and sets the tap location of the meter s flowing pressure sensor valid selections are Upstream and Downstream Note The Upstream and Downstream fields only display when the meter type is orifice 3 Click Apply to save any changes and proceed to Section 3 3 3 to configure the Advanced tab Rev July 15 Configuration 25 Liquid Allocation Program for Continuous Flow User Manual 3 3 3 Liquid Meters Advanced Tab Use this tab to configure additional information for a liquid meter To access this screen 1 Select the Advanced tab on the Liquid Meters screen One of the following two screens displays im ROCLINK 800 Liquid Meters SE ROCLINK B00 Liquid Meters Fle Edt View ROC Configure Meter nities Took Window Heb TE a fecal Meter Liites Took Window Help Og M bs Ate WME PFSZORZF AR 2K mr How AP Faon oe TE Point Number 1 Lig Me a Tog laMu 1 fig Mu aT 7 Tag Leg Mi t Germal Inputs Advanced Alama Flow Rates Flow Totakzers Densities Dap Merth Totakzers Gerani Ingets Advancedl Alas Flew Fates Flow Tolakzere Dewutere CgyMorth Tolakere Aamorphenc Prernse Meter Factor Ktactor Curve Adrien Pisum Calculate Erte Moles Pact m Caus O Enig Linh Maie Ps haen i4 46632 Psia o aae PSA i Stan
57. d Allocation Program for Continuous Flow User Manual Chapter 4 Reference This section presents tables of ranges of base densities for each of the Liquid Types shown on the Liquid Products screen discusses how history is handled by the program and lists the parameters of the user defined points used by the Liquid Allocation program including the following Point Type 22 Liquid Preferences Point Type Point Type 23 Liquid Products Point Type Point Type 25 Liquid Meters Point Type Point Type 26 Liquid Density Interfaces Point Type Rev July 15 Reference 59 Liquid Allocation Program for Continuous Flow User Manual 4 1 Density Ranges for Liquid Product Types The following tables show the ranges of base densities for the types of liquid that can be selected on the Liquid Products screen Be sure to review the notes for each liquid type when determining which liquid applies to your application Crude Oil Includes Gas Well Condensate Table Version Base Density Range Kg m3 Base Density Range API Gravity 1980 610 1075 0 100 Note Paraffinic condensate drip gasoline from a gas well comprised of butanes pentanes hexanes and heptanes should be considered Crude Oil provided its base density lies within the range for Crude Oil Otherwise it should be considered a Light Hydrocarbon Se E E Notes Aromatic natural gasoline should be considered Gasoline With the 1980 Table even though one of the
58. d Preferences screen Sets the material of construction of the pipe in which the orifice is installed Valid selections are Stainless Steel Monel and Carbon Steel Note This field only displays when the meter type is orifice Ref Sets the reference temperature for Temperature the measurement of the pipe diameter The units are the temperature units selected on the Liquid Preferences screen 3 Click Apply to save any changes and proceed to Section 3 3 4 to configure the Alarms tab 28 Configuration Rev July 15 Liquid Allocation Program for Continuous Flow User Manual 3 3 4 Liquid Meters Alarms Tab Use this tab to configure the alarms for a liquid meter To access this screen 1 Select the Alarms tab on the Liquid Meters screen The following screen displays sam ROCLINK 800 Liquid Meters Eile Edit view ROC Configure Meter Utilities Tools Window Help Dw Oi E Yow hit Seo we Point Number f1 Lig Mtr 1 v Tag Lig Mtr 1 Alarming Opti 100000 0 eras a High Alarm Limit 100000 0 Bbl day se sable C Alarm on Indicated Volume Rate Low Alam Limit 5 000 0 Btls C Alarm on Gross Volume Rate Alarm Deadband 100 0 Bbl day C Alarm on Gross Standard Volume Rate C Alarm on Net Standard Volume Rate C Alarm on Mass Rate RB On Alarm Set On Alarm Clear Print Save As Auto Scan 2 Update Close gt DERE oaan Figure 18 Liquid Meters Alarms tab 2 Review and change
59. density units selected on the Liquid Preferences screen Note This value is only used if the base density option on the Inputs tab of the Liquid Meters screen is set to use the base density of the product 2 Click Apply to save any changes and proceed to Section 3 2 2 to configure the Advanced tab Rev July 15 Configuration 17 Liquid Allocation Program for Continuous Flow User Manual 3 2 2 Liquid Products Advanced Tab Use this tab to specify additional information as appropriate for the liquid products To access this screen 1 Select the Advanced tab on the Liquid Products screen One of the following four screens displays im ROCLINK 800 Liquid Products an UCL EW POD Ltquid Products Eile Edit view ROC Configure Meter Utilities Tools Window Help Fle Edt Yew ROC Configue Meter ities Took Window Help Osh ra Wr Aiwa S2Ogelinmriew Og M i NTa WHE FAZORZT UF iP F Point Number 1 Product 1 v Product Tag Product 1 Een eee Aoda St me Produa Tag Product 21 Product Definition Advanced UserDetredAlha 03419 10 3x Vol Frac Dagf Compeesnlity Optons O AusoSelect Compeesnibdty Table AutoSelect Compressibility Table C API Chapter 11 21 M Compressibility Options C API Chapter 11 2 1 M AP Chapter 11 22M f Defined Comorernibainy C API Chapter 11 2 2 M Meee C User Defined Compressibility User Defined F 349 10 5 x Vol Frac PS Save As Auto Scan Update Close m Piiri ON LIN
60. ders Steel C Stender Steel C Mena Mera C Cabon Sheed i alhon Shaa Elevador 500 0 Fert 0 l Elevator E T Fe Be Tempra Bet Dempeahar 5 0 jesi Deg F jenn Deg F E Fono 11 0 4 Y viac 0 Cia LevEh Sec Motes Factor 10 Meter Factor Ktactor Options e Single MF Singe K factor O MF Ouv Single Ktactor Ketacter Curve Single MF Force Rocsiouishon l Set e Choo Pie Savers Pasa Scan Update We pd iweke pie tee E Uedu Update ___De E sey N LINE J Figure 17 a Liquid Meters Advanced tab Figure 17 b Liquid Meters Advanced tab Meter Type is Linear Meter Type is Orifice 2 Review and change as necessary the values in the following fields Field Description Atmospheric Sets how the atmospheric pressure at the site of the Pressure liquid meter is determined Valid selections are Calculate and Enter Select Calculate to calculate the atmospheric pressure based on the specified elevation Select Enter to manually enter the value for the atmospheric pressure The units are the pressure absolute units selected on the Liquid Preferences screen Elevation Sets the elevation at the site of the liquid meter The units are the elevation units selected on the Preferences screen Viscosity Sets the flowing viscosity for the meter The units are the viscosity units selected on the Liquid Preferences screen Note This field only displays when the meter type is
61. e Coratarts mutt be hom a calivahon certiicate ung denaty ures of Ko m3 tempershee unts ol Dog C and pressure urs of Baek O updse _ Cose aw l ado Scan 5l Update Quse DERNE 1129 Figure 26 a Liquid Density Interfaces Micro Motion Constants tab Density Input Type is not a Micro Motion or Solartron Densitometer Figure 26 b Liquid Density Interfaces Micro Motion Constants tab Density Input Type is a Micro Motion or Solartron Densitometer 2 Review and change as necessary the values in the following fields Field Description Basic Sets three transducer constant values KO K1 amp K2 Transducer used to calculate the uncorrected density for the Micro Constants Motion or Solartron densitometer 50 Configuration Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Field Description Pressure Sets four pressure correction constant values K20A Correction K20B K21A and K21B for the Micro Motion or Constants Solartron densitometer Temperature Sets two temperature correction constant values K18 Correction amp K19 for the Micro Motion or Solartron Constants densitometer Velocity of Enables or disables correction of the density for the Sound velocity of sound in the liquid Valid values are Correction Enabled or Disabled Liquid VOS Sets a value for the velocity of sound in the liquid for the Micro Motion or Solartron densitometer Calibration This
62. e density interface point Possible alarms are Low High and Manual Notes A Manual alarm means one or more of the density temperature or pressure I O definitions on the Inputs tab is Undefined You define these alarms on the Alarms tab Density Sets a density correction factor which is a multiplier to Correction correct the densitometer s calculated density This Factor value is typically obtained after performing a densitometer calibration using a pycnometer or similar device Apply Select to apply a correction for the temperature effects Hydrometer on a glass hydrometer For more information refer to Correction the Manual of Petroleum Measurement Standards Chapter 9 Note This field only displays when Analog Density is selected as the Density Input Type 2 Click Apply to save any changes and proceed to Section 3 4 2 to configure the Inputs tab Rev July 15 Configuration 47 Liquid Allocation Program for Continuous Flow User Manual 3 4 2 Liquid Density Interfaces Inputs Tab Use this tab to configure a density interface point s inputs for density temperature and pressure To access this tab 1 Select the Inputs tab on the Liquid Density Interfaces screen One of the following two screens display wa ROCLINK 800 Liquid Density Interfaces R C Configure Meter Unities Took Window Heb Gb NTa ME PFZORZTF AR 2K Tag Density 91 igts Mico Motion Constants UGC Constants Alama 10 Do
63. easurement site observed pressure in the pressure units specified by TLP 22 0 1 9 Basic Transducer Constant KO R W FL 4 Any floating point 0 0 Constant KO from the calibration certificate number of the Micro Motion or Solartron or UGC densitometer The program uses this 98 Reference Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Point Type 26 Densitometer Parameters Parm Name Access Data Type Length Range Default Description 10 Basic Transducer Constant K1 R W FL 4 Any floating point 0 0 Constant K1 from the calibration certificate number of the Micro Motion or Solartron or UGC densitometer This program uses this constant in the general density calculation 11 Basic Transducer Constant K2 R W FL 4 Any floating point 0 0 Constant K2 from the calibration certificate number of the Micro Motion or Solartron or UGC densitometer The program uses this constant in the general density calculation 12 Micro Motion Temperature R W FL 4 Any floating point 0 0 If the densitometer type is Micro Motion or Correction Constant K18 number Solartron parameter 1 is set to 0 Constant K18 from the calibration certificate of the Micro Motion or Solartron densitometer The program uses this constant in the temperature compensation calculation Otherwise Not used 13 Micro Motion Temperature R W FL 4 Any floating point 0 0 If the densitometer type is Micro Motion or Correction Constant K19 num
64. econd If the Meter Type field on the General tab is set to Linear and the Units Type of Flow Meter Input field on the Inputs tab is set to Mass or if the Meter Type is Orifice the program calculates this value by dividing the gross mass GM flow by the flowing density The result is added to the totalizer once a second The units are the volume units selected on the Liquid Preferences screen This read only field shows the gross standard volume GSV flow totalizer The program calculates this value by multiplying the gross volume GV flow by the correction factor for the temperature of the liquid CTL and the correction factor for the pressure of the liquid CPL The result is added to the totalizer once a second Units are the volume units selected on the Liquid Preferences screen This read only field shows the current net standard volume NSV flow totalizer The program calculates this value by multiplying the gross standard volume GSV flow by the base sediment and water CSW correction factor The result is added to the totalizer once a second Units are the volume units selected on the Liquid Preferences screen Configuration 35 Liquid Allocation Program for Continuous Flow User Manual Field Description S amp W Volume This read only field shows the sediment and water Total S amp W volume flow totalizer The program calculates this value by adding the net standard volume NSV flow minus the gross standard volu
65. eeeeeeeeeeeeeseeaeeeeseeseeeeeeeesas 18 39 BIGUIE Meters SChO CM nien a a ste GavsauinS asta ean sa 20 3 3 1 Liquid Meters General Tabb isinin 21 3 3 2 Liquid Meters Inputs Tab ccce a aa a aa aaas 23 3 3 3 Liquid Meters Advanced Tab cccccssesecccceessseececeeeseceesceeuseceessaaaeeeeeesaegeeeeseaas 26 3 3 4 Liquid Meters Alarms Tab ccccccccccssseeccsesseeceesseeceeseeessagsecsagseessegseeessaeeeeess 29 3 3 5 Liquid Meters Flow Rates Tab ccccccccccssseecceeseeeceeseeeceeueecsanseeeseseeesseseeeees 31 3 3 6 Liquid Meters Flow Totalizers Tab ccccccccccseeeeeeeeeeeeceeeeeeeeeseseeeeseeesseeeeens 34 3 3 7 Liquid Meters Densities Tab eccccssecceesseeeeeseeseeeeeeseeesaeaeeesseeeeeseeeeesseeeeeas 37 3 3 8 Liquid Meters Day Month Totalizers Tab ccccccseecceeeeeeseeeeeseeeeeeeseeseeseeeeeeas 41 3 4 Liquid Density Interfaces Screen ccccccccccccaseeeeeeeeeeeeeeeeeceeseeeaseeeseeeeeeeessaaaaeeeeeeessaaaaeses 44 3 4 1 Liquid Density Interfaces General Tab ccccccceeccccccceeeeeseeeeeeeeeseeaeeeeeeeeeeesaaas 46 3 4 2 Liquid Density Interfaces Inputs Tab cee cceeeeeeeeeeeeeeeeeeeeeeeeaeaeeeeeeaeeeeeeeeeas 48 3 4 3 Liquid Density Interfaces Micro Motion Constants Tab cccseceeeeeeseseeeeeees 50 3 4 4 Liquid Density Interfaces UGC Constants Tab cccccccsssecceeeeesseeeeeeeeeeeeeeens
66. erwise Not used Multiplier value to correct the observed density before it is stored to parameters 30 31 and 32 Observed density in the units selected for the observed density TLP 22 0 3 Observed density in units of relative density Observed density in units of API gravity Rev July 15 Access Data Type Length Range R W FL 4 Any floating point number R W FL 4 Any floating point number R W FL 4 Any floating point number R W FL 4 gt 0 0 R O FL 4 gt 0 0 R O FL 4 gt 0 0 R O FL 4 0 0 to 100 0 Reference 103 Liquid Allocation Program for Continuous Flow User Manual Point Type 26 Densitometer Parameters Parm Name Access Data Type Length Range Default Description 33 Hydrometer Correction Option R W UINT8 1 0 gt 1 0 Enable status for correction for a hydrometer when calculating the base density 0 Disabled 1 Enabled 34 Periodic Time RO FL 4 0 0 0 0 If the density interface type is a Micro Motion or Solartron or UGC densitometer TLP 27 Logical 1 is O or 2 Period between cycles of the densitometer input in microseconds If the density interface type is an analog value TLP 27 Logical 1 is 3 Not used 35 Alarm Code R O BIN 0x00 Alarm statuses Bit 7 Manual mode status 0 No inputs for the observed density calculation is a manual entry 1 At least one input for the observed density calculation is a manual entry Bit 6 Reserved Bit 5 Reserved Bit 4
67. eter 112 hw is set to 0 0 The units are sqrt of the units specified by TLP 22 0 0 74 Reference Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name Access Data Length Range Default Description Type 28 Indicated Flow Totalizer R O FL 4 gt 0 0 0 0 Continuous totalizer of the indicated flow The Volume or Mass value rolls over when it exceeds 1000000 0 If the type of units of the liquid meter flow input parameter 3 is volume Total indicated volume through the meter The volume units are specified by TLP 22 0 6 If the type of units of the liquid meter flow input parameter 3 is mass Total indicated mass through the meter The mass units are specified by TLP 22 0 7 If the meter type parameter 104 is orifice Total of sart hw Units are sqrt of the units specified by TLP 22 0 0 29 Gross Volume Flowrate R O FL 4 gt 0 0 0 0 Gross volume flowrate as indicated by the meter The volume units are specified by TLP 22 0 6 and the time units are specified by TLP 22 0 8 30 Gross Volume Totalizer R O FL 4 gt 0 0 0 0 Continuous totalizer of the gross volume flow The value rolls over when it exceeds 1000000 0 The volume units are specified by TLP 22 0 6 31 Gross Standard Volume R O FL 4 gt 0 0 0 0 Volume flowrate at base conditions The volume Flowrate units are specified by TLP 22 0 6 and the time
68. field shows the current gross standard volume GSV flow rate The program calculates this value by multiplying the gross volume GV rate by the correction factor for the temperature of the liquid CTL and the correction factor for the pressure of the liquid CPL The units are the volume and flow rate time units selected on the Liquid Preferences screen This read only field shows the current net standard volume NSV flow rate The program calculates this value by multiplying the gross standard volume GSV rate by the base sediment and water S amp W correction factor The units are as specified for the volume and flow rate time units selected on the Liquid Preferences screen 32 Configuration Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Field Description S amp W Volume This read only field shows the current sediment and Rate water S amp W volume flow rate The program calculates this value by subtracting the net standard volume NSV flow rate from the gross standard volume GSV flow rate The units are as specified for the volume and flow rate time units selected on the Liquid Preferences screen Gross Mass This read only field shows the current gross mass Rate GM flow rate The units are as specified for the mass and flow rate time units selected on the Liquid Preferences screen If the Meter Type field on the General tab is set to Linear and the Units Type of Flow Meter Input field on
69. for use in the FB107 and the user manual for the Liquid Allocation Program for Continuous Flow QER 10Q006 for use in the FB107 with Measurement Canada firmware The standard version of this program 1LK 7 only works with the standard version of FB107 firmware The Measurement Canada version of this program QER 10Q006 only works with the Measurement Canada version of FB107 firmware This manual describes how to download and configure this program referred to as the Liquid Allocation program or the program throughout the rest of this manual You access and configure this program using ROCLINK 800 Configuration Software version 1 80 or greater loaded on a personal computer PC running Windows 8 or Windows 7 32 or 64 bit The sections in this manual provide information in a sequence appropriate for first time users Once you become familiar with the procedures and the software running in a FB107 the manual becomes a reference tool This manual has the following major sections Chapter l Introduction Chapter 2 Installation Chapter 3 Configuration Chapter 4 Reference This manual assumes that you are familiar with the FB107 and its configuration For more information refer to the following manuals FloBoss 107 Flow Manager Instruction Manual Form A6206 ROCLINK 800 Configuration Software User Manual for FB107 Form A6217 Rev July 15 Introduction 1 Liquid Allocation
70. four program specific screens Liquid Preferences Liquid Products Liquid Meters and Liquid Density Interfaces Use the Liquid Preferences screen to set the units of the inputs and calculated results values Use the Liquid Products screen to configure up to two liquid hydrocarbon or water products which can be selected as the fluid passing through a liquid meter run Use the Liquid Meters screen to configure and view the results for up to two liquid meter runs through which one of the liquid products defined by the Liquid Products screen flows One of the configuration items is to specify if the base density for the product passing through the meter is to be calculated from a Liquid Density Interface point or to use the user specified base density for the liquid product Use the Liquid Density Interface screen to configure and view the observed densities for up to two liquid density interface points wa ROCLINK 800 On Line Com1 FB107 FB107 Eile Edit View ROC Configure Meter Utilities Tools Window Help Dee tae SiGe Ve Nhe VE SOB A SEF H On Line Com FB107 FB107 KAE Ml Modules me 1 0 3 amp Control RJ Meter System History User Program Administrator E Liquid Alloc Display 23 Liquid Preferences Display 24 Liquid Products Display 26 Liquid Meters E Display 27 Liquid Density Interfaces User Display General Advanced 1 0 Paints Meter Paint
71. hen you access the Liquid Meters screen to specify a liquid meter s description liquid product passing through it meter type base temperature and base or vapor pressure Any active alarms are also shown on this tab mam ROCLINK 800 Liquid Meters FB107 File Edit View ROC Configure Meter Utilities Tools Window Help Dw Oi H Yow Mit Seo we R Point Number 1 Liq Mtr 1 v Tag Liq Mtr 1 General Inputs Advanced Alarms Flow Rates Flow Totalizers Densities Day Month Totalizers Meter Description Product Selection Product 1 Crude Oil Product 1 Meter Type Base Temperature Linear 60DegF C Orifice C 15DegC C 20DegC C 30DegC Base Vapor Pressure 0 0 PSIG Active Alarms None Pie SaveAs AutoScan 2 Update Close O 1 41 Pw Figure 15 Liquid Meters General tab 1 Review and change as necessary the values in the following fields Field Description Meter Sets a description for the liquid meter up to 30 Description alphanumeric characters Product Sets the product as defined on the Liquid Products Selection screen associated with the liquid meter Click wv to display additional products The liquid type and its tag display to the right of the selected product rrr rer Meter Type Sets the type of meter for the liquid meter run Valid selections are Linear and Orifice Notes Linear meter c
72. ified by TLP 22 0 6 83 Gross Standard Volume This R O FL 4 gt 0 0 0 0 Total so far this month of the volume flow at base Month conditions The volume units are specified by TLP 22 0 6 84 Net Standard Volume This R O FL 4 gt 0 0 0 0 Total so far this month of the volume flow at base Month conditions minus the non merchantable quantities The volume units are specified by TLP 22 0 6 85 S amp W Volume This Month R O FL 4 gt 0 0 0 0 Total so far this month of the volume flow of non merchantable quantities The volume units are specified by TLP 22 0 6 86 Mass This Month R O FL 4 gt 0 0 0 0 Total so far this month of the mas flow The mass units are specified by TLP 22 0 7 Rev July 15 Reference 85 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name Access Data Length Range Default Description Type 87 Indicated Flow Previous Month R O FL 4 gt 0 0 0 0 Previous month s total indicated flow If the meter type parameter 104 is linear and the type of units of the liquid meter flow input parameter 3 is volume Previous month s total indicated volume flow The volume units are specified by TLP 22 0 6 If the meter type parameter 104 is linear and the type of units of the liquid meter flow input parameter 3 is mass Previous month s total indicated mass flow The mass units are specified by TLP 22 0 7 If the meter type parameter 104 i
73. ineering units for length orifice and plate diameters 0 Inch 1 millimeter Engineering units for viscosity of the liquids 0 Lb ft sec 1 Cp centipoise Engineering units for volume values 0 Bbl 1 Mcf 2 Km3 3 Gal US 4 ft3 5 m3 6 Liter Engineering units for mass values 0 Lb 1 Kg 2 Ton short 3 Tonne 1000 kg 4 Mib Time units for flow rates 0 Per day 1 Per hour 2 Per minute 3 Per second Current status of the Liquid Allocation program 1 Program running 2 License key not available Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Point Type 22 Liquid Preferences Parameters Parm Name Access Data Length Range Default Description Type 10 Product and Meter Density Units R W UINT8 1 02 0 Engineering units for densities of the product and meter point types 0 Kg m3 1 Relative Density 2 API Gravity 11 Accumulation Rollover Value RO FL 4 gt 0 0 1000000 Rollover value for all of the continuous totalizers 12 Elevation Units R W UINT8 1 0 gt 1 0 Engineering units for elevation 0 Feet 1 Meter Rev July 15 Reference 67 Liquid Allocation Program for Continuous Flow User Manual 4 4 Point Type 23 Liquid Product Parameters Point type 23 contains the parameters for configuring the liquid products There are two logicals for this point type Point Type 23 Liquid Product Parameters Parm Name A
74. ing on the type of units of the flow meter TLP 25 x 3 If the meter type parameter 104 is linear and the flow input is a pulse input Not used 113 Expansion Factor R O FL 4 gt 0 0 1 0 If the meter type parameter 104 is orifice Meter expansion factor Y1 If the meter type parameter 104 is linear Not used 114 Coefficient of Discharge R O FL 4 gt 0 0 1 0 If the meter type parameter 104 is orifice Coefficient of discharge CdFT If the meter type parameter 104 is linear Not used 115 Actual Orifice Diameter R O FL 4 gt 0 0 4 000 If the meter type parameter 104 is orifice Orifice diameter at the flowing temperature The units are specified by TLP 22 0 4 If the meter type parameter 104 is linear Not used 116 Actual Pipe Diameter R O FL 4 gt 0 0 8 071 If the meter type parameter 104 is orifice Pipe diameter at the flowing temperature The units are specified by TLP 22 0 4 If the meter type parameter 104 is linear Not used Rev July 15 Reference 93 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name Access Data Length Range Default Description Type 117 Actual Beta R O FL 4 gt 0 0 0 4956 If the meter type parameter 104 is orifice Beta at the flowing temperature If the meter type parameter 104 is linear Not used 118 Velocity of Approach R O FL 4 gt 0 0 1 03 If the
75. ion Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name Access Data Length Range Default Description Type 58 Meter Factor 8 Flowrate K R W FL 4 gt 0 0 0 0 If a K Factor Curve Single Meter Factor has Factor 8 Frequency been selected parameter 42 2 this parameter is the frequency in Hz that corresponds with the associated K Factor lf a Meter Factor Curve Single K Factor has been selected parameter 42 1 this parameter is the indicated flowrate that corresponds to the associated meter factor 59 Meter Factor 9 K Factor 9 R W FL 4 gt 0 0 1 0 If a K Factor Curve Single Meter Factor has been selected parameter 42 2 this parameter is the meter constant K Factor in pulses unit of flow input for the associated frequency in Hz If a Meter Factor Curve Single K Factor has been selected parameter 42 1 this parameter is the dimensionless meter factor MF for the associated indicated flowrate 60 Meter Factor 9 Flowrate K R W FL 4 gt 0 0 0 0 If a K Factor Curve Single Meter Factor has Factor 9 Frequency been selected parameter 42 2 this parameter is the frequency in Hz that corresponds with the associated K Factor lf a Meter Factor Curve Single K Factor has been selected parameter 42 1 this parameter is the indicated flowrate that corresponds to the associated meter factor 61 Meter Factor 10 K Factor 10 R W FL 4 gt 0
76. ise Not used If the densitometer type is UGC parameter 1 is set to 2 Constant Pc from the calibration certificate of the UGC densitometer The program uses this constant in the pressure compensation calculation Otherwise Not used Rev July 15 Reference 101 Liquid Allocation Program for Continuous Flow User Manual Point Type 26 Densitometer Parameters Parm Name 22 UGC Pressure Correction Constant Kp1 23 UGC Pressure Correction Constant Kp2 24 UGC Pressure Correction Constant Kp3 25 UGC Temperature Correction Constant Tc 102 Access Data Type Length Range R W FL 4 Any floating point number R W FL 4 Any floating point number R W FL 4 Any floating point number R W FL 4 Any floating point number Reference Default 0 0 0 0 0 0 0 0 Description If the densitometer type is UGC parameter 1 is set to 2 Constant Kp1 from the calibration certificate of the UGC densitometer The program uses this constant in the pressure compensation calculation Otherwise Not used If the densitometer type is UGC parameter 1 is set to 2 Constant Kp2 from the calibration certificate of the UGC densitometer The program uses this constant in the pressure compensation calculation Otherwise Not used If the densitometer type is UGC parameter 1 is set to 2 Constant Kp3 from the calibration certificate of the UGC densitometer The program uses this constant in
77. its are 10 times the volume fraction per temperature unit The temperature units are as specified on the Liquid Preferences screen F This read only field shows the compressibility of the liquid when adjusting the volume from the base to the flowing pressure If the meter s base pressure is 60 Deg F the units are 10 times the volume fraction per pressure unit If the meter s base pressure Is 15 20 or 30 Deg C the units are 10 times the volume fraction per pressure unit The pressure units are as specified on the Liquid Preferences screen CSW Factor This read only field shows the correction factor for the sediment and water in the liquid It is calculated as 100 S amp W 100 Its value is 1 0 when the of sediment and water S amp W is 0 0 Base Density This read only field shows the density of the liquid at Density Values the base temperature and pressure The units are specified by the Base and Flowing Density Units field on the Liquid Preferences screen Flowing Density This read only field shows the density of the liquid at Density Values the flowing temperature and pressure The units are specified by the Base and Flowing Density Units field on the Liquid Preferences screen Observed This read only field shows the density of the liquid at Density the observed temperature and pressure The units are Density Values specified by the Base and Flowing Density Units field on the Liquid Preferences screen
78. ity units specified by TLP 22 0 10 20 Flow Input TLP R W TLP 3 TLP 0 0 0 TLP for the uncorrected flowrate from the meter 21 Static Pressure TLP R W TLP 3 TLP 0 0 0 TLP for the static pressure 22 Temperature TLP R W TLP 3 TLP 0 0 0 TLP for the flowing temperature 23 S amp W TLP R W TLP 3 TLP 0 0 0 TLP for the percent of sediment and water S amp W 24 Static Pressure Value R W FL 4 0 0 Value of the flowing pressure in units specified by TLP 22 0 1 25 Temperature Value R W FL 4 0 0 Value of the flowing temperature in units specified by TLP 22 0 2 26 S amp W Value R W FL 4 gt 0 0 0 0 Percentage by volume of the sediment and water S amp W in the liquid 27 Indicated Flowrate Volume or R W FL 4 gt 0 0 0 0 If the meter type parameter 104 is linear and Mass the type of units of the liquid meter flow input parameter 3 is volume Indicated volume flowrate through the meter The volume units are specified by TLP 22 0 6 and the time units are specified by TLP 22 0 8 If the meter type parameter 104 is linear and the type of units of the liquid meter flow input parameter 3 is mass Indicated mass flowrate through the meter The mass units are specified by TLP 22 0 7 and the time units are specified by TLP 22 0 8 If the liquid meter type parameter 104 is orifice sqrt hw If the flow input is less than or equal to the differential pressure for low flow cutoff param
79. le is converted to the density units required by the table Rev July 15 API Table 5A 6A API Table 5B 6B API Table 5D 6D API Table 6C API Table 23A 24A API Table 23B 24B API Table 23D 24D GPA TP 27 23E 24E API Table 24C API Table 53A 54A API Table 53B 54B API Table 53D 54D GPA TP 27 Table 53E 54E API 2540 Table 54C IP 3 Table 59A 60A IP 3 Table 59B 60B IP 3 Table 59D 60D GPA TP 27 Table 59E 60E API Procedure 11 1 6 2004 Note Configuration API Procedure 11 1 7 2004 API Table 23A 24A API Table 23B 24B API Table 23D 24D GPA TP 27 23E 24E API Table 24C API Table 53A 54A API Table 53B 54B API Table 53D 54D GPA TP 27 Table 53E 54E API 2540 Table 54C IP 3 Table 59A 60A IP 3 Table 59B 60B IP 3 Table 59D 60D GPA TP 27 Table 59E 60E API 11 4 1 2003 Invalid Table Invalid Table appears when the liquid type is a refined product gasoline jet fuel or fuel oil and the base density is out of range The valid base density range for refined products are as follows 1980 Tables 350 0 1075 0 kg m3 2004 Tables 350 0 1163 5 kg m3 39 Liquid Allocation Program for Continuous Flow User Manual Field Description Tables Used for Pressure Table This read only field shows the Correction pressure correction standard also Factor referred to as table used in continued calculating the flowing density and if specified base density of the liquid The following are the po
80. low Rates Flow Totakrers Derwites Dap Month Toakzers Today Veuhenday Mirth Prevas Morth Today Yeuterday Morth Prevent Morth indicated Vohane 120160 00 1201606 100 Indiosted Mare 2300 0 o 2300 0 0 0 Gross Vae 13 Ot bbe 13 tbh fa Gross Volume E B522 foo E6522 Grote Slarcieed Voksi 12 S8645 1283545 Grote Slaid Voksne 6 568495 oo 6562499 Net Standard Vome 1200645 Net Standard Volume 6 349 ao 6 568493 SEW Volume f SEW Vome 00 foo ino Gross Mats i 512272 Gross Mase 23000 00 2300 0 Birt Savers AasaScan P Update cwe Pie Savers AvoScan 2 Update Cove ON LINE ee ON LINE a Figure 22 a Liquid Meters Day Month Totalizer tab Figure 22 b Liquid Meters Day Month Totalizer tab Meter Type is Linear and Units Type of Flow Meter Input is Meter Type is Linear and Units Type of Flow Meter Input is Volume Mass wae ROCLINK 800 Liquid Meters Z Fle Edt Yew BOC Configwe Meter tities Tools Window Help Dae i Gt b Ate WME FSZORTF A 2H Port Number 1 Liq Me 1 Tog lgMe al Gerezi inputs Adverced Adore Flow Rates Flow Totakzers Dornes Dap Month Totakzers Today Veuherday Morth Prevent Morth Groat Voke 4027273 joo 4027273 fo Grats Starcfaed Voksne 29065 94 00 IGES 94 a0 Net Standard Volume 33665 94 IDES 4 SiW Vome 00 a0 i wo Gross Mase 139590000 wo fi IS 0 00 Piri GareAs
81. lowing temperature and pressure 1 A density interface point is assigned to the liquid meter parameter 17 but the observed density is not the density at the liquid meter So the liquid meter s base density is to be calculated using the observed density and the liquid meter s base temperature and equilibrium or base pressure Then the flowing density is calculated using the base density and flowing temperature and pressure 2 A density interface point is assigned to the liquid meter parameter 17 and the observed density is the density at the liquid meter So the liquid meter s base density is to be calculated using the observed density and the liquid meter s base temperature and equilibrium or base pressure The flowing density is set to the value of the observed density 17 Density Interface Point R W UINT8 1 0 1 0 Specifies the density interface point assigned to the liquid meter It is used if the density interface option parameter 16 is not equal to 0 18 Flowing Density R O FL 4 gt 0 0 999 016 Flowing density for the meter in the density units specified by TLP 22 0 10 Rev July 15 Reference 73 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name Access Data Length Range Default Description Type 19 Base Density R O FL 4 gt 0 0 999 016 Density of the liquid at the base temperature and base or equilibrium pressure in the dens
82. lume fraction per pressure unit The pressure units are specified by TLP 22 0 1 Reference temperature for the base volume 0 60 Deg F 1 Reserved 2 15DegC 3 20 Deg C 4 30 Deg C This parameter displays the numeric value of the base temperature selected by the base temperature option parameter 99 Units are Deg F or Deg C depending on the value of parameter 99 Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name Access Data Length Range Default Description Type 101 Base Equilibrium Pressure R W FL 4 gt 0 0 0 0 Base or equilibrium bubble point pressure for the current product in gauge pressure units specified by TLP 22 0 1 The equilibrium pressure is the minimum pressure at which bubbles of gas appear in a liquid Rev July 15 Reference 89 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name Access Data Length Range Default Description Type 102 Temperature Correction Table R O UINT8 1 0 gt 34 99 4 Temperature correction table used to calculate the flowing density which is calculated using the even numbered table where applicable If the base density is calculated from the observed density the odd numbered table is utilized where applicable Denotes the base density had to be converted to units that match that of the table 0 API 2540 Table 5 6A 1980
83. me GSV flow to the totalizer once a second The units are the volume units selected on the Liquid Preferences screen Gross Mass This read only field shows the gross mass GM flow Total totalizer If the Meter Type field on the General tab is set to Linear and the Units Type of Flow Meter Input field on the Inputs tab is set to Volume the program calculates this value by multiplying the gross volume GV flow by the flowing density The result is added to the totalizer once a second If the Meter Type field on the General tab is set to Linear and the Units Type of Flow Meter Input field on the Inputs tab is set to Mass the program calculates this value by multiplying the indicated mass IM flow by the meter factor MF The result is added to the totalizer once a second If the Meter Type field on the General tab is set to Orifice the program calculates this value by integrating the result of the IS05167 2003 orifice flow rate calculation once a second The units are the mass units selected on the Liquid Preferences screen 3 Click Apply to save any changes 4 Click Close to close this screen Proceed to Section 3 3 7 to view the values on the Densities tab 36 Configuration Rev July 15 Liquid Allocation Program for Continuous Flow User Manual 3 3 7 Liquid Meters Densities Tab Use this tab to view a meter s correction factors densities and information showing how these values are calculated To access this
84. meter type parameter 104 is orifice Velocity of approach Ev at the flowing temperature If the meter type parameter 104 is linear Not used 119 Reynolds Number R O FL 4 gt 0 0 0 00 If the meter type parameter 104 is orifice Pipe Reynolds number ReD at flowing conditions If the meter type parameter 104 is linear Not used OG a S SSC SSC T ETETA Bit 7 Not used Bit 6 Not used Bit 5 Not used Bit 4 Not used Bit 3 Not used Bit 2 Atmospheric pressure source 0 Calculate based on the elevation 1 Manual entry Bit 1 Pressure reference 0 Gauge 1 Absolute Bit 0 Pressure tap location orifice meters only 0 Downstream 1 Upstream 94 Reference Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm 126 127 128 Name Atmospheric Pressure Elevation Request Recalculation Status Observed Density in Observed Density Units Observed Density in Base and Flowing Density Units Temperature Average Observed Temperature Average Observed Pressure Rev July 15 Access R W R W R O Alpha for Observed to Base R O R O R O R O Data Type FL FL FL Length Range Default 4 gt 0 0 14 73 4 Any floating 500 point number 1 0 1 0 1 gt 0 0 999 016 1 gt 0 0 999 016 1 gt 0 0 0 3417773 4 Any floating 60 point
85. n displays nam ROCLINK 800 Liquid Products FB107 File Edit View ROC Configure Meter Utilities Tools Window Help Dae W Ot kz VY tM S44 ee EY hk Point Number f1 Product 1 v Product Tag Product 1 Product Definition Advanced Liquid Type API Table Base Density Crude Dil 1980 999 016 Kg m3 C Gasoline e 2004 C Jet Fuel C Fuel Oil C Lube Oil C Special Application C Light Hydrocarbon C Water Pie Save As Auto Scan Update Close E ONE 11 21 4m Figure 11 Liquid Products Screen Note Two fields at the top of the screen Point Number and Product Tag appear on both tabs Configuration Rev July 15 Liquid Allocation Program for Continuous Flow User Manual 4 Review and change as necessary the values in the following fields Rev July 15 Field Description Point Number Selects the liquid product to configure Click w to display all of the products Clicking a different liquid product causes the screen to display the values for that product Product Tag Sets a unique identifier for the selected liquid product 5 Click Apply to save any changes and proceed to Section 3 2 1 to configure the Values tab Configuration 15 Liquid Allocation Program for Continuous Flow User Manual 3 2 1 Liquid Products Product Definition Tab Use this tab which displays when you access the Liquid Products screen to specify the liquid type API table and the base densit
86. ng 100 0 Value that the selected flowrate for alarming see point number parameter 7 must be above the low alarm limit parameter 11 or below the high alarm limit parameter 12 before the associated alarm clears 14 K Factor R W FL 4 gt 0 0 1 0 If the meter input is a PI point this is the meter constant K Factor in pulses unit volume or pulses unit mass If a K Factor curve is being used parameter 42 this is equal to the current value of the K Factor If the meter is not a PI point Not used 15 Meter Factor R W FL 4 gt 0 0 1 0 Value obtained by dividing the quantity of fluid measured by the proving system by the quantity indicated by the meter during proving 72 Reference Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name Access Data Length Range Default Description Type 16 Density Interface Option R W UINT8 1 0 gt 2 0 Specifies if a density interface point is assigned to the liquid meter If a density interface point is assigned the base density for the liquid meter is determined from the observed density Otherwise the base density of the product assigned to the liquid meter is used 0 No density interface point is assigned to the liquid meter so use the base density specified by parameter 7 of the liquid product assigned to the meter parameter 2 Then the flowing density is calculated using the base density and f
87. ng the Base Density Access R O R O Base Temperature Option Base Temperature Value R O R W R O Data Type FL FL UINT8 FL Length Range Default 4 gt 0 0 1 0346 4 gt 0 0 1 0 4 gt 0 0 0 0 1 04 0 4 60 0 15 0 20 0 or 30 0 Reference Description Factor for adjusting the volume of the liquid from the observed temperature to the base temperature This value gets set whenever the base density for the meter is to be determined from the observed density of a density interface point Factor for adjusting the volume of the liquid from the observed pressure to the base or equilibrium pressure This value gets set whenever the base density for a meter is to be determined from from the observed density of a density interface point 60 0 Compressibility factor used to determine the base density from the observed density This value gets set whenever the base density for the meter is to be determined from the observed density of a density interface point and the temperature correction table includes adjustment for the difference between the observed and base pressure when determining the base density from the observed density This only applies in the case of the API 11 1 6 2004 and API 11 1 7 2004 tables If the base temperature is 60 Deg F the units are 10 5 times the volume fraction per pressure unit If the base temperature is 15 20 or 30 Deg C the units are 10 6 times the vo
88. nt in the pressure compensation calculation Otherwise Not used 17 Micro Motion Pressure Correction R W FL 4 Any floating point 0 0 If the densitometer type is Micro Motion or Constant K21B number Solartron parameter 1 is set to 0 Constant K21B from the calibration certificate of the Micro Motion or Solartron densitometer The program uses this constant in the pressure compensation calculation Otherwise Not used 100 Reference Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Point Type 26 Densitometer Parameters Parm Name Access Data Type Length Range 18 Velocity of Sound Compensation R W UINT8 1 0 1 Option 19 Liquid Velocity of Sound R W FL 4 gt 0 0 20 Calibration Velocity of Sound R O FL 4 gt 0 0 21 UGC Pressure Correction R W FL 4 Any floating point Constant Pc number Default 0 0 0 0 0 0 0 0 Description If the densitometer type is Micro Motion or Solartron parameter 1 is set to 0 Velocity of sound compensation enable status 0 Disabled 1 Enabled Otherwise Not used If the densitometer type is Micro Motion or Solartron parameter 1 is set to 0 Actual velocity of sound in the liquid at flowing conditions in meters per second Otherwise Not used If the densitometer type is Micro Motion or Solartron parameter 1 is set to 0 Velocity of sound in the liquid at the calibration conditions in meter per seconds Otherw
89. number 4 Any floating 0 0 point number Reference Description Atmospheric pressure at the meter location The units are specified by TLP 22 0 1 Elevation of the meter The units are specified by TLP 22 0 13 Request recalculation status When the recalculation for a meter run is requested recalculation of all meter runs is performed 0 Recaculation is not requested 1 Recalculation is requested Average observed density during the previous mcp The units are those specified for the observed density TLP 22 0 3 Average observed density during the previous mcp The units are those specified for the base and flowing densities TLP 22 0 11 Coefficient of thermal expansion used when adjusting the volume at the observed temperature to the base temperature The units are 10 3 times the volume fraction per Deg F or Deg C depending on the selected temperature units The units of the temperature increment are specified by TLP 22 0 2 Average observed temperature during the previous mcp The units of the temperature are specified by TLP 22 0 2 Average observed pressure during the previous mcp The units of the pressure are specified by TLP 22 0 1 95 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name Access Data Length Range Default Description Type 129 No Flow Time R W UINT8 1 0 255 10 If the meter type parameter 104 is orifice
90. of a Micro Motion densitometer Notes Micro Motion densitometers were formerly labeled as Solartron densitometers These fields only display when the Density Input Type field on the General tab is set to Micro Motion or Solartron 7830 40 or 7835 45 46 47 For further details refer to the Micro Motion Technical Manual for 7835 45 46 47 Liquid Density Meter 78355080_US Rev C October 2007 The constants entered must be from a calibration certificate using density units of Kg m3 temperature units of Deg C and pressure units of BarA To access this screen 1 Select the Micro Motion Constants tab on the Liquid Density Interfaces screen One of the following two display wat ROCLINK 800 Liquid Density Inter mae ROCLINK BOO Liquid Density Interfaces Ble Edt Yew ROC Configure Meter Unit Toos n a mm Y R C Configze Meter ities Tools Window Heb gt ey 7M M is NTa MH FZORZTF HL e Tag Density 51 Density 31 Tas Derwty 1 General ireuts Mato Moton Corntarts UGC Corstarts Alwns inputs Maceo Mabon Constards UGC Constants Alama Temperature Conection Constants KO 150207 ki awos Dasic Transducer Comstarts 0230472 Ki 1023043 Ki2 oor K 0001147 lias appas on thet Lab nhan fa saisciad Dertdy Ingat Type s t Meso Modor ot Solanan 7330 40 of PRISAS 46 47 Derretorneten Presse Conechon Constants Velocty of Seas Comochori K20 foooman Enabled Disabled Laud VOS fy 0 Caltestion VOS 7 Not
91. or Curve Single K Factor has been selected parameter 42 1 this parameter is the dimensionless meter factor MF for the associated indicated flowrate 52 Meter Factor 5 Flowrate K R W FL 4 gt 0 0 0 0 If a K Factor Curve Single Meter Factor has Factor 5 Frequency been selected parameter 42 2 this parameter is the frequency in Hz that corresponds with the associated K Factor lf a Meter Factor Curve Single K Factor has been selected parameter 42 1 this parameter is the indicated flowrate that corresponds to the associated meter factor 53 Meter Factor 6 K Factor 6 R W FL 4 gt 0 0 1 0 If a K Factor Curve Single Meter Factor has been selected parameter 42 2 this parameter is the meter constant K Factor in pulses unit of flow input for the associated frequency in Hz If a Meter Factor Curve Single K Factor has been selected parameter 42 1 this parameter is the dimensionless meter factor MF for the associated indicated flowrate Rev July 15 Reference 79 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name Access Data Length Range Default Description Type 54 Meter Factor 6 Flowrate K R W FL 4 gt 0 0 0 0 If a K Factor Curve Single Meter Factor has Factor 6 Frequency been selected parameter 42 2 this parameter is the frequency in Hz that corresponds with the associated K Factor If a Meter Factor Cur
92. or an analog density value from any source 3 Density Input Value R W FL 4 gt 0 0 999 012 Value of the density input If the density input is a frequency from a densitometer this value contains the frequency in Hz Otherwise it contains the density input value in the units specified for the observed density TLP 22 0 3 Rev July 15 Reference 97 Liquid Allocation Program for Continuous Flow User Manual Point Type 26 Densitometer Parameters Parm Name Access Data Type Length Range Default Description 4 Alarm Config Statuses R W UINT8 1 0 Alarm configuration statuses Bit 7 Reserved Bit 6 RBX on alarm set 0 Disabled 1 Enabled Bit 5 RBX on alarm clear 0 Disabled 1 Enabled Bit 4 Alarming 0 Disabled 1 Enabled Bit 3 Reserved Bit 2 Reserved Bit 1 Reserved Bit 0 Reserved 5 Observed Temperature TLP R W TLP 3 TLP 0 0 0 TLP of the temperature at the density measurement location observed temperature 6 Observed Temperature R W FL 4 Any floating point 60 0 Value of the temperature at the density number measurement location observed temperature in the temperature units specified by TLP 22 0 2 7 Observed Pressure TLP R W TLP 3 TLP 0 0 0 TLP for the pressure at the density measurement location observed pressure 8 Observed Pressure R W FL 4 Any floating point 0 0 Value of pressure at the density number measurement location m
93. ram file The User Program Administrator screen displays As shown in Figure 5 note that the Download User Program File frame identifies the selected program and that the Download amp Start button is active User Program Administrator User Programe Installed in Device 2 No Program 3 No Program 4 No Program 5 No Program 6 Ho Program cea See sie Download User Program File PK Mame No Program Version Library Yersion Created DRAM Used O CRC O0 FLASH Used Entry Ft Displays Status Empty E Pragram Files Liquid amp liac_1 bin Download amp Start Download Name Liquid Alloc Yersion Rev 1 10 eo 1 2009 3 57 17 PM OxC2C 94560 Update Close Figure 5 User Program Administrator Installation Rev July 15 Liquid Allocation Program for Continuous Flow User Manual 7 Click Download amp Start to begin loading the selected program The following message displays Confirm Download Download amp Start User Program 1 Figure 6 Confirm Download Note For the FB107 ROCLINK 800 assigns program positions based on memory allocations For this reason the Liquid Alloc program automatically installs as program 1 Because the program is larger than 64K it occupies two user C program numbers 1 amp 2 8 Click Yes to begin the download During the download the program performs a warm start creates an event in the event log and when
94. rdon Valued erty ANBI EU B506 uwe aN 82 EU ee 0 we WIN BO EU hao mehi fado Scan o Update Cove DENE 1120 Figure 25 a Liquid Density Interfaces Inputs tab Density Input Type is an Analog Density wee ROCLINK BOD Liquid Density Interfaces R C Configure Meter ities Took Window Heb M NTa WH FSC CAR aR 2H Taz Dersty 81 Micro Motion Constants UGC Constants Alya 170 Detter Values s FO h0 1415 246 ave As faso Scan B Update Cote Figure 25 b Liquid Density Interfaces Inputs tab Density Input Type is a Frequency Densitometer 2 Review and change as necessary the values in the following fields Field Density Temperature 48 Configuration Description Assigns the point type logical and parameter TLP of the density I O value of the selected density interface point Click to display the Select TLP screen and define your TLP selection If you select Undefined 0 0 0 for the density input you can manually enter a value for the density input Otherwise the value of the selected input is displayed Note Assigns the point type logical and parameter TLP of the temperature I O value for the selected density interface point Click to display the Select TLP screen and define your TLP selection If you select Undefined 0 0 0 for the temperature input you can manually enter a value for the temperature Otherwise the value of
95. read only field shows the VOS calculated calibration value for the velocity of sound in the liquid based on the temperature and pressure corrected density 3 Click Apply to save any changes and proceed to Section 3 4 4 to configure the UGC Constants tab Rev July 15 Configuration 51 Liquid Allocation Program for Continuous Flow User Manual 3 4 4 Liquid Density Interfaces UGC Constants Tab wa ROCLINK 800 Liquid Density Interfaces Fle Edt Wew ROC Oa Port Number 1 Density 1 Figure 27 a Liquid Density Interfaces UGC Constants tab Density Input Type is not a UGC 278 Densitometer 52 Configure Meter ities Took Window Hep M i vw Taz Dertiy 91 General inputs Mico Motion Constants _ UGt Constarts Alama wit S2ORZGF WL 2 Use this tab to configure a density interface point s constants for calculating the density for a UGC 278 densitometer Notes These fields only display when the Density Input Type field on the General tab is set to UGC 278 Densitometer For further details refer to the UGC Model 278 Vibrating Densitometer User Manual UA27800 Rev B The constants entered must be from a calibration certificate using density units of g cm3 temperature units of Deg F and pressure units of Psig To access this screen 1 Select the UGC Constants tab on the Liquid Density Interfaces screen One of the following two screens display dae ROCLINK 800 Liquid Density Interface
96. refined products is specified as the liquid product type the program compares the meter run s base density against the ranges listed below and calculates the flowing density based on the product that falls within the range gt 1075 Kg m3 Invalid Table gt 838 9 Kg m3 Fuel Oil gt 787 5 Kg m3 Jet Fuel gt 70 5 Kg m3 Transition Product gt 350 Kg m3 Gasoline even though the low range is 650 Kg m3 the program calculates a flowing density if the base density is greater than or equal to 350 Kg m3 lt 350 Kg m3 Invalid Table With the 2004 Table even though one of the refined products is specified as the liquid product type the program compares the meter run s base density against the ranges listed below and calculates the flowing density based on the product that falls within the range gt 1163 5 Kg m3 Invalid Table gt 838 3 Kg m3 Fuel Oil gt 787 5 Kg m3 Jet Fuel gt 70 4 Kg m3 Transition Product gt 350 Kg m3 Gasoline even though the low range is 650 Kg m3 the program calculates a flowing density if the base density is greater than or equal to 350 Kg m3 lt 350 Kg m3 Invalid Table 60 Reference Rev July 15 Liquid Allocation Program for Continuous Flow User Manual O w cones Note A Lube Oil is derived from a crude oil fraction by distillation or asphalt precipitation ame T T Note The valid range of the coefficient of thermal exp
97. rence temperature The units are specified by TLP 22 0 4 If the meter type parameter 104 is linear Not used 109 Orifice Reference Temperature R W FL 4 Any floating 68 0 If the meter type parameter 104 is orifice point number Reference temperature for the orifice diameter measurement The units are specified by TLP 22 0 2 If the meter type parameter 104 is linear Not used 110 Orifice Material R W UINT8 1 0 gt 2 0 If the meter type parameter 104 is orifice Orifice material 0 Stainless Steel 304 or 316 1 Monel 2 Carbon Steel If the meter type parameter 104 is linear Not used 111 Viscosity R W FL 4 gt 0 0 4 0E 04 If the meter type parameter 104 is orifice Absolute flowing viscosity The units are specified by TLP 22 0 5 If the meter type parameter 104 is linear Not used 92 Reference Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name Access Data Length Range Default Description Type 112 Low Differential Pressure Cutoff R W FL 4 gt 0 0 1 0 If the meter type parameter 104 is orifice Differential pressure at or below which the flowrate is set to 0 0 The units are specified by TLP 22 0 0 If the meter type parameter 104 is linear and the flow input is not a pulse input Flow input value below which the flowrate is set to 0 0 The units are the specified volume or mass units depend
98. rently selected input Sets the source for the flowing pressure of the liquid meter Click lto display the Select TLP screen and specify the TLP selection The units are the pressure units selected on the Liquid Preferences screen Note If you select Undefined 0 0 0 for the I O definition you can manually enter a value in the Value field Otherwise the program displays the value for the currently selected input Sets the source for the percent of sediment and water for the liquid meter Click to display the Select TLP screen and specify the TLP selection Note If you select Undefined 0 0 0 for the I O definition you can manually enter a value in the Value field Otherwise the program displays the value for the currently selected input Sets the type of units for the meter flow input Valid selections are Volume and Mass Note This field only displays when the meter type is linear Sets the inside diameter for the pipe near the liquid meter The units are the diameter units selected on the Liquid Preferences screen Note This field only displays when the meter type is orifice Sets the diameter of the orifice plate of the liquid meter The units are the diameter units selected on the Liquid Preferences screen Note This field only displays when the meter type is orifice Sets the low flow cutoff point When the valve of the flow input of the liquid meter is less than this value the calculated flow ra
99. rs corresponding to flow rates in the Meter Factor K factor Curve frame and a value for the K factor field K factor Curve Uses a series of K factor curve Single MF values and a single meter factor Specify up to 12 K factors corresponding to pulse frequencies in the Meter Factor K factor Curve frame and a value for the Meter Factor field Force Forces an immediate recalculation of the flow for the Recalculation current main calculation period mcp A new main calculation period begins at this time Select Set to force the recalculation When the recalculation is complete the selection is automatically reset to Clear Rev July 15 Configuration 27 Liquid Allocation Program for Continuous Flow User Manual Field Meter Factor K factor Curve Orifice Material Pipe Material Description Sets up to 12 entries for the Meter Factor K factor curve Notes The fields in this frame can only be set if you select MF Curve Single K factor or K factor Curve Single MF in the Meter Factor K factor Options field This field only displays when the meter type is linear Sets the material of construction of the orifice Valid selections are Stainless Steel Monel and Carbon Steel Note This field only displays when the meter type is orifice Ref Sets the reference temperature for Temperature the measurement of the orifice diameter The units are the temperature units selected on the Liqui
100. s Fle Edt View AOC Configure Meter Uniities Tools Window Help Og Gt h Ate ME FSZORZTF A 2K Port Number 1 Oeraty 31 Taz Dern 81 General inputs Mico Motion Constants UGI Constants Aluma Bane Tramaducer Constants Temperate Comecton Constants K 1 64911 hiami appas On the tab when the selected Derity Inout Type it UGC 278 Denstometer Note Constants mutt be from a calbvation certificate uning denaty units of g om3 temperature unis of Deg F and perae ures of Pag Piri Save s fato Scan a Update Cove Figure 27 b Liquid Density Interfaces UGC Constants tab Density Input Type is a UGC 278 Densitometer 2 Review and change as necessary the values in the following fields Field Description Basic Sets three transducer constant values KO K1 amp K2 Transducer used to calculate the uncorrected density for the UGC Constants densitometer Pressure Sets the calibration pressure Pc and three pressure Correction correction constant values Kp1 Ko2 and Kps for the Constants UGC densitometer Configuration Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Rev July 15 Field Description Temperature Sets the calibration temperature Tc and three Correction temperature correction constant values Kt1 Kt2 and Constants Kt3 for the UGC densitometer 3 Click Apply to save any changes 4 Click Close to close this screen Proceed to Section 3 4 5 to configure
101. s Diagnostic Installed Module CPU Actual Module jen Description Application Firmware Revision fRe 120 Part Number jwesis2 Build Date un 23 2008 7 40 00 C C Serial Number W48083x0022 D E 07460021 Boot Revision Rev 1 00 Boot Build Date Nov 17 2006 8 32 Integrity poe Auto Scan 2 Update t Apply ONNE ean Figure 9 ROCLINK 800 Rev July 15 Configuration 11 Liquid Allocation Program for Continuous Flow User Manual 3 1 Liquid Preferences Screen Once you have successfully loaded the Liquid Allocation program into the FloBoss you can access the Liquid Preferences screen and configure the units for the inputs and calculated results for the program To access this screen 1 Click User Program gt Liquid Alloc from the ROCLINK configuration tree 2 Double click Display 23 Liquid Preferences The Liquid Preferences screen displays mam ROCLINK 800 Liquid Preferences File Edit View ROC Configure Meter Utilities Tools Window Help Dee St Aw h S 4Oge iw ew Program Status Liquid Units Selections aa Running Temperature Units Volume Units Base and Flowing Density Units DegF Bbl Kg m3 C DegC C Mef C Relative Density C Km3 C API Gravity Gal Pressure Units CR Psi oE Observed Density Units s kPa C Liter Kg m3 C Bar C g em3 Kg cm2 Mass Units C Lbstt3 f Lb C Lb bbl Units for Orifice Meters Kg C Lb agal Diff Press Units 2 Ton C Relative Density g InH20
102. s orifice Previous month s total of sqrt hw Units are sqrt of the units specified by TLP 22 0 0 88 Gross Volume Previous Month R O FL 4 gt 0 0 0 0 Previous month s total gross volume The volume units are specified by TLP 22 0 6 89 Gross Standard Volume R O FL 4 gt 0 0 0 0 Previous month s total volume at base Previous Month conditions The volume units are specified by TLP 22 0 6 90 Net Standard Volume Previous R O FL 4 gt 0 0 0 0 Previous month s total volume at base conditions Month minus the non merchantable quantities The volume units are specified by TLP 22 0 6 91 S amp W Volume Previous Month R O FL 8 gt 0 0 0 0 Previous month s total volume of non merchantable quantities The volume units are specified by TLP 22 0 6 92 Mass Previous Month R O FL 4 gt 0 0 0 0 Previous month s total mass The mass units are specified by TLP 22 0 7 86 Reference Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name Access Data Length Range Default Description Type 93 Meter uncorrected flowrate R W FL 4 gt 0 0 0 0 Flow input of the liquid meter If the meter type parameter 104 is linear and the type of units of the liquid meter flow input parameter 3 is volume Indicated volume flowrate through the meter This value matches that of the indicated flowrate parameter 27 The volume units
103. ssible entries for the field User Entered F API Table 11 2 1 API Table 11 2 1M API Table 11 2 2 API Table 11 2 2M API Prodedure 11 1 6 2004 API Prodedure 11 1 7 2004 API 11 4 1 2003 Invalid Table Note Invalid Table appears when the liquid type is a refined product gasoline jet fuel or fuel oil and the base density is out of range The valid base density range for refined products are as follows 1980 Tables 350 0 1075 0 kg m3 2004 Tables 350 0 1163 5 kg m3 3 Click Apply to save any changes and proceed to Section 3 3 8 to view the values on the Day Month Totalizers tab 40 Configuration Rev July 15 Liquid Allocation Program for Continuous Flow User Manual 3 3 8 Liquid Meters Day Month Totalizers Tab Use this tab to view a liquid meter s totalizers for the current and previous day and month To access this screen 1 Select the Day Month Totalizers tab on the Liquid Meters screen One of the following three screens displays wae ROCLINK BOD Liquid Meters DER wa ROCLINK 500 Liquid Meters fe Edt Yew ROC Configue Meter Rites Tools Window Help Fle Edt Yew ROC Configue Meter nities Took Window Help Oe M bs Ate WHE PFSZORZF AR 2H Oa M bs Ate ME FZORZF AR 2H Powe Number 11 Lig Me a7 gt Teg La Me 1 Port Number 1 Lig Me 1 kd Tog ILa Me 1 Geena inputs Adenda Alma Flow Rates Flow Totakrers Dersities Dap Month Toxakzers Green inputs Advereed Alsema F
104. sult to the totalizers This calculation occurs once a second If the Meter Type field on the General tab is set to Linear and the Units Type of Flow Meter Input field on the Inputs tab is set to Mass or if the Meter Type field on the General tab is set to is Orifice the program calculates this value by dividing the gross mass GM flow by the flowing density and adding the result to the totalizers This calculation occurs once a second The units are the volume units selected on the Liquid Preferences screen Gross Standard Volume This read only field shows the gross standard volume GSV flow totals for the current and previous days and months The program calculates these values by adding the gross volume GV multiplied by the correction factors for the temperature of the liquid CTL and pressure of the liquid CPL to the totalizers once a second The units are the volume units selected on the Liquid Preferences screen 42 Configuration Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Field Description Net Standard This read only field shows the net standard volume Volume NSV flow totals for the current and previous days and months The program calculates these values by adding the gross standard volume GSV multiplied by the sediment and water CSW correction factor to the totalizers once a second The units are the volume units selected on the Liquid Preferences screen S amp W Volume This re
105. t Standard Volume Today 73 S amp W Volume Today 74 Mass Today 75 Indicated Volume Yesterday 76 Gross Volume Yesterday 77 Gross Standard Volume Yesterday 78 Net Standard Volume Yesterday 79 S amp W Volume Yesterday 80 Mass Yesterday 84 Access R O Data Type FL R O R O R O R O R O Length Range 4 gt 0 0 4 gt 0 0 4 gt 0 0 4 gt 0 0 4 gt 0 0 4 gt 0 0 4 gt 0 0 4 gt 0 0 4 gt 0 0 Reference Default 0 0 Description Total so far today of the volume flow at base conditions minus the non merchantable quantities The volume units are specified by TLP 22 0 6 Total so far today of the volume flow of non merchantable quantities The volume units are specified by TLP 22 0 6 Total so far today of the mass flow The mass units are specified by TLP 22 0 7 Yesterday s total indicated flow If the type of units of the liquid meter flow input parameter 3 is volume Yesterday s total indicated volume The volume units are specified by TLP 22 0 6 If the type of units of the liquid meter flow input parameter 3 is mass Yesterday s total indicated mass The mass units are specified by TLP 22 0 7 If the meter type parameter 104 is orifice Yesterday s total of sqrt hw Units are sart of the units specified by TLP 22 0 0 Yesterday s total gross volume flow The volume units are specified by TLP
106. te Europe Emerson Process Management Remote Automation Solutions Unit 8 Waterfront Business Park Dudley Road Brierley Hill 2015 Remote Automation Solutions a business unit of Emerson Process Management All Dudley UK DY5 1LX rights reserved iad mince os Oe Remote Automation Solutions a business unit of Emerson Process Management shall not be EmersonProcess com Remote liable for technical or editorial errors in this manual or omissions from this manual REMOTE North American Latin America AUTOMATION SOLUTIONS MAKES NO WARRANTIES EXPRESSED OR IMPLIED INCLUDING THE Emerson Process Management IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WITH Remote Automation Solutions RESPECT TO THIS MANUAL AND IN NO EVENT SHALL REMOTE AUTOMATION SOLUTIONS BE 6005 Rogerdale Road LIABLE FOR ANY INCIDENTAL PUNITIVE SPECIAL OR CONSEQUENTIAL DAMAGES INCLUDING Houston TX USA 77072 BUT NOT LIMITED TO LOSS OF PRODUCTION LOSS OF PROFITS LOSS OF REVENUE OR USE T 1 281 879 2699 F 1 281 988 4445 AND COSTS INCURRED INCLUDING WITHOUT LIMITATION FOR CAPITAL FUEL AND POWER www EmersonProcess com Remote AND CLAIMS OF THIRD PARTIES Emerson Process Management Ltd Remote Automation Solutions UK is a wholly owned subsidiary of Emerson Electric Co doing business as Remote Automation Solutions a business unit of Emerson Process Management FloBoss ROCLINK ControlWave Helicoid and OpenEnterprise are trademarks of Remo
107. te Automation Solutions AMS PlantWeb and the PlantWeb logo are marks owned by one of the companies in the Emerson Process Management business unit of Emerson Electric Co Emerson Process Management Emerson and the Emerson logo are trademarks and service marks of the Emerson Electric Co All other marks are property of their respective owners The contents of this publication are presented for informational purposes only While every effort has been made to ensure informational accuracy they are not to be construed as Middle East Africa Emerson Process Management Remote Automation Solutions Emerson FZE P O Box 17033 Jebel Ali Free Zone South 2 Dubai U A E T 97148118100 F 971 4 8865465 www EmersonProcess com Remote Asia Pacific warranties or guarantees express or implied regarding the products or services described Emerson Process Management herein or their use or applicability Remote Automation Solutions reserves the right to modify Remote Automation Solutions or improve the designs or specifications of such products at any time without notice All sales 1 Pandan Crescent are governed by Remote Automation Solutions terms and conditions which are available upon Singapore 128461 request Remote Automation Solutions does not assume responsibility for the selection use or T 65 6777 8211 F 65 6777 0947 maintenance of any product Responsibility for proper selection use and maintenance of any www EmersonProcess com Remote Remote Au
108. te is set to 0 0 and the system records a No Flow alarm in the Alarm Log if alarming is enabled The units are the same as the Flow Meter Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Field Description Density Options Sets the source for the base and flowing density of the liquid meter Valid selections are Note This field does not display if the liquid type is water Set base equal Liquid meter calculations use the to product base density of the product base calculate assigned to the meter and flowing from calculate the flowing density from base the base density Calculate base Liquid meter calculations from observed determine the base density from calculate the specified Density Interface flowing from Point field and calculate the base flowing density from the base density Calculate base Liquid meter calculations from observed determine the base density from set flowing the specified Density Interface equal to Point field and set the flowing observed density to the value of the observed density SONEAUSGEAEEEESESEEEEOESOESESESUSOESESOSOESERSESESOSSESESESSSSESESSSSSSIEIEEE ENE TTT TTT TT TT TTT TT TESTS TST LT TS TS TSS ES TST SS ESTES ESSE SEES OSU SSESSUSSESOSUSEOSSSSSESOSSESEESESESCESESESESSESESEESESESESOESESESSESESEESESONES m Density Sets the source for the observed density of the liquid Interface Point meter Note This field only displays if you select either Cal
109. the download completes displays the following message ROCLINK 800 l Download amp Start User Program COMPLETED Figure 7 ROCLINK 800 Download Confirmation 9 Click OK The User Program Administrator screen displays see Figure 8 Note that The User Programs Installed in Device frame identifies the loaded program The Status field indicates that the program is running Rev July 15 Installation 9 Liquid Allocation Program for Continuous Flow User Manual User Program Administrator User Programe Installed in Device 1 Liguid Alloc Name Liquid Alloc Mo Prograrn Ho Prograrn Version Aew 1 10 Library Version Rew 2 Ho Prograrn No Pragram Created 08 31 2009 15 57 17 DRAM Used 32768 No Program CALC OsleCy FLASH Used 94560 Ent Pt O 540000 Displays 23 24 26 27 lear Status Running Download User Program File E Pragram Files sLiquid amp liac_1 bin Browse Name Liquid Alloc Download amp Start Download Version Aew 1 10 Created 873172009 3 57 17 PM CRC OzC2C Size 44560 Figure 8 User Program Administrator 10 Click Close and proceed to Chapter 3 to configure the program Installation Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Chapter 3 Configuration After you download and start the Liquid Allocation program you configure the program and view calculation results using ROCLINK 800 software To do this you use
110. the program status There is one logical for this point type Point Type 22 Liquid Preferences Parameters Access Parm Name 0 Differential Pressure Units 1 Pressure Units 2 Temperature Units 3 Observed Density Units 65 Data Type UINT8 UINT8 UINT8 UINT8 Length Range 1 0 gt 3 1 0 gt 3 1 0 1 1 0 6 Reference Default Description Engineering units for differential pressure values 0 InH20 1 kPa 2 mBar 3 mmH20 Engineering units for pressure values Flowing pressure units are in gauge or absolute depending on the selection for the meter TLP 25 meter logical 120 Bit 1 The atmospheric pressure units are always absolute 0 Psi 1 kPa 2 Bar 3 Kg cm2 Engineering units for temperature values 0 Deg F 1 Deg C Engineering units for the observed density determined by a density interface point 0 Kg m3 1 g cc 2 Lb ft3 3 Lb bbl 4 Lb gal 5 Relative Density 6 API Gravity Rev July 15 Liquid Allocation Program for Continuous Flow User Manual Point Type 22 Liquid Preferences Parameters Parm Name Access 4 Length Units R W 5 Viscosity Units R W 6 Volume Units R W 7 Mass Units R W 8 Flowrate Time Units R W 9 Program Status R O 66 Data Type UINT8 UINT8 UINT8 UINT8 UINT8 UINT8 Length Range 1 0 gt 1 1 0 gt 1 1 0 6 1 0 4 1 0 gt 3 1 0 gt 2 Reference Default Description Eng
111. ting and clearing the alarm continuously when the value of the alarming parameter oscillates around the alarm limit The units are based on the selected Alarming Option 3 Click Apply to save any changes and proceed to Section 3 3 5 to view the values on the Flow Rates tab 30 Configuration Rev July 15 Liquid Allocation Program for Continuous Flow User Manual 3 3 5 Liquid Meters Flow Rates Tab Use this tab to view the current values of a liquid meter s flow rates To access this screen 1 Select the Flow Rates tab on the Liquid Meters screen One of the following three screens displays wae ROCLINK 800 Liquid Meters sj wae ROCLINK BOO Liquid Meters Fle Edt View AOC Configure Meter nities Tools Window Help m Fle Edt Yew AOC Configure Meter tities Tools Window Help D Sa M b NTa ME FZORZF A 2W Dw M bs Ate WE FRZOZF HA 2H Port Number 1 Liq Me 1 Tog laMe a Port Number 1 Liq Me 1 Tog amsa Geren ints Advacod Alms Flow Rates Flow Totakzers Densities DapMterih Totakeres Geren inputs Advanced Alms Flow Rates Flow Totatzers Densities Dap Month Totakzess Indicated Volume Fite 14800 Bbbday PA Indeated Mait Rae D00 dy im Giot Vome Rae fano b d GV V HF Giott Vome Rae haas GV GM 7 Feming Deity Gross Standed Volume Rate 1425455 Btwaw GSV GV CTL CPL Gross Standed Volume Rae 11370818 GSV GV CTL CPL Net Standard Volume Rate 1425455 Belda MSV GSV CSW Net
112. tomation Solutions product remains solely with the purchaser and end user EMERSON Remote Automation Solutions
113. ty 0 User compressibility 1 API Table 11 2 1 2 API Table 11 2 1M 3 API Table 11 2 2 4 API Table 11 2 2M 5 API Procedure 11 1 6 2004 6 API Procedure 11 1 7 2004 7 API 11 4 1 2003 99 Invalid Table 104 Meter Type R W UINT8 1 0 gt 1 0 Type of meter 0 Linear 1 Orifice with flange taps uses 1505167 105 Nominal Pipe Diameter R W FL 4 gt 0 0 8 071 If the meter type parameter 104 is orifice Pipe internal diameter at the pipe reference temperature The units are specified by TLP 22 0 4 If the meter type parameter 104 is linear Not used 106 Pipe Reference Temperature R W FL 4 Any floating 68 0 If the meter type parameter 104 is orifice point number Reference temperature for the orifice diameter measurement The units are specified by TLP 22 0 2 If the meter type parameter 104 is linear Not used 107 Pipe Material R W UINT8 1 0 gt 2 2 If the meter type parameter 104 is orifice Pipe material 0 Stainless Steel 304 or 316 1 Monel 2 Carbon Steel If the meter type parameter 104 is linear Not used Rev July 15 Reference 91 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name Access Data Length Range Default Description Type 108 Nominal Orifice Diameter R W FL 4 gt 0 0 4 000 If the meter type parameter 104 is orifice Orifice diameter at the orifice refe
114. units are specified by TLP 22 0 8 32 Gross Standard Volume R O FL 4 gt 0 0 0 0 Continuous totalizer of the volume flow at base Totalizer conditions The volume units are specified by TLP 22 0 6 33 Net Standard Volume Flowrate R O FL 4 gt 0 0 0 0 Volume flowrate at base conditions corrected for non merchantable quantities such as sediment and water Applies to crude oil only For other liquid products it is identical to gross standard volume flowrate The volume units are specified by TLP 22 0 6 and the time units are specified by TLP 22 0 8 Rev July 15 Reference 75 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name Access Data Length Range Default Description Type 34 Net Standard Volume Totalizer R O FL 4 gt 0 0 0 0 Continuous totalizer of the volume flow at base conditions corrected for non merchantable quantities such as sediment and water Applies to crude oil only For other liquid products it is identical to the gross standard volume total The value rolls over when it exceeds 1000000 0 The volume units are specified by TLP 22 0 6 35 Mass Flowrate R W FL 4 gt 0 0 0 0 Mass flowrate The mass units are specified by TLP 22 0 7 and the time units are specified by TLP 22 0 8 36 Mass Totalizer R O FL 4 gt 0 0 0 0 Continuous totalizer of the mass flow The value rolls over when it exceeds 1000000 0 The mass units are specified by TL
115. ut for the associated frequency in Hz If a Meter Factor Curve Single K Factor has been selected parameter 42 1 this parameter is the dimensionless meter factor MF for the associated indicated flowrate 11 Liquid Allocation Program for Continuous Flow User Manual Point Type 25 Liquid Meter Parameters Parm Name Access Data Length Range Default Description Type 46 Meter Factor 2 Flowrate K R W FL 4 gt 0 0 0 0 If a K Factor Curve Single Meter Factor has Factor 2 Frequency been selected parameter 42 2 this parameter is the frequency in Hz that corresponds with the associated K Factor lf a Meter Factor Curve Single K Factor has been selected parameter 42 1 this parameter is the indicated flowrate that corresponds to the associated meter factor 47 Meter Factor 3 K Factor 3 R W FL 4 gt 0 0 1 0 If a K Factor Curve Single Meter Factor has been selected parameter 42 2 this parameter is the meter constant K Factor in pulses unit of flow input for the associated frequency in Hz If a Meter Factor Curve Single K Factor has been selected parameter 42 1 this parameter is the dimensionless meter factor MF for the associated indicated flowrate 48 Meter Factor 3 Flowrate K R W FL 4 gt 0 0 0 0 If a K Factor Curve Single Meter Factor has Factor 3 Frequency been selected parameter 42 2 this parameter is the frequency in Hz that corresponds with the associated K Factor
116. ve Single K Factor has been selected parameter 42 1 this parameter is the indicated flowrate that corresponds to the associated meter factor 55 Meter Factor 7 K Factor 7 R W FL 4 gt 0 0 1 0 If a K Factor Curve Single Meter Factor has been selected parameter 42 2 this parameter is the meter constant K Factor in pulses unit of flow input for the associated frequency in Hz If a Meter Factor Curve Single K Factor has been selected parameter 42 1 this parameter is the dimensionless meter factor MF for the associated indicated flowrate 56 Meter Factor 7 Flowrate K R W FL 4 gt 0 0 0 0 If a K Factor Curve Single Meter Factor has Factor 7 Frequency been selected parameter 42 2 this parameter is the frequency in Hz that corresponds with the associated K Factor lf a Meter Factor Curve Single K Factor has been selected parameter 42 1 this parameter is the indicated flowrate that corresponds to the associated meter factor 57 Meter Factor 8 K Factor 8 R W FL 4 gt 0 0 1 0 If a K Factor Curve Single Meter Factor has been selected parameter 42 2 this parameter is the meter constant K Factor in pulses unit of flow input for the associated frequency in Hz If a Meter Factor Curve Single K Factor has been selected parameter 42 1 this parameter is the dimensionless meter factor MF for the associated indicated flowrate 80 Reference Rev July 15 Liquid Allocat
117. y of a liquid product Eile Edit view ROC Configure Meter Utilities Tools Window Help saw ROCLINK 800 Liquid Products FB107 DER A ROCLINK 800 Liquid Products FB107 DER _ ax _ a x Eile Edit View ROC Configure Meter Utilities Tools Window Help D gA Oi E Whe ht Se eORR LR 2 R Dw Oi E Yh MP Seo HR 2 A A Point Number AIRA ate MaE i v Product Tag Product 1 Point Number 1 Product 1 z Product Tag Product 1 Product Definition Advanced Product Definition Advanced Liquid Type API Table Base Density Liquid Type API Table Base Density Crude Dil 1980 999 016 Kg m3 C Crude Dil Q 4988 Kym C Gasoline 2004 C Jet Fuel C Fuel Oil C Lube Oil C Gasoline C Jet Fuel C Fuel Gil C Lube Oil C Special Application C Light Hydrocarbon C Water C Special Application Light Hydrocarbon C Water Print Save As Auto Scan Update Close Print Save As Auto Scan Update Close Apply gt gt ERRIRE 11 55AM BARE 12 00 PM Figure 12 a Liquid Products Product Definition tab Figure 12 b Liquid Products Product Definition tab Liquid Type is Not Light Hydrocarbon or Water Liquid Type is Light Hydrocarbon im ROCLINK 800 Liquid Products FB107 DEK a X File Edit Yiew ROC Configure Meter Utilities Tools Window Help Dw Oi k Whe ht Seok He 2 A Point Number 1 Product 1 A Product Tag Product 1 Product Definition Advanced Liquid Type API Table Base

Liquid Allocation Program for Continuous Flow

Contents

Download Pdf Manuals

Related Search

Related Contents