User Manual
Contents
1. DAC BT05 POS M B with Intel Atom N270 VGA LVDS TTL Giga LAN USB SATA SSD Trusted ePlatform Services AD ANTECH Copyright The documentation and the software included with this product are copyrighted 2011 by Advantech Co Ltd All rights are reserved Advantech Co Ltd reserves the right to make improvements in the products described in this manual at any time without notice No part of this manual may be reproduced copied translated or transmitted in any form or by any means without the prior written permission of Advantech Co Ltd Information provided in this manual is intended to be accurate and reliable However Advantech Co Ltd assumes no responsibility for its use nor for any infringements of the rights of third parties which may result from its use Acknowledgements Award is a trademark of Award Software International Inc IBM PC AT PS 2 and VGA are trademarks of International Business Machines Cor poration Intel and Atom are trademarks of Intel Corporation Microsoft Windows is a registered trademark of Microsoft Corp RTL is a trademark of Realtek Semi Conductor Co Ltd ESS is a trademark of ESS Technology Inc UMC is a trademark of United Microelectronics Corporation SMI is a trademark of Silicon Motion Inc Creative is a trademark of Creative Technology LTD CHRONTEL is a trademark of Chrontel Inc All other product names or trademarks are properties of their respective owners2. Product Warranty 2 years Advantech warrants to you the original purchaser that each of its products will be free from defects in materials and workmanship for two years from the date of pur chase This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech or which have been subject to misuse abuse accident or improper installation Advantech assumes no liability under the terms of this warranty as a consequence of such events Because of Advantech s high quality control standards and rigorous testing most of our customers never need to use our repair service If an Advantech product is defec tive it will be repaired or replaced at no charge during the warranty period For out of warranty repairs you will be billed according to the cost of replacement materials service time and freight Please consult your dealer for more details If you think you have a defective product follow these steps 1 Collect all the information about the problem encountered For example CPU speed Advantech products used other hardware and software used etc Note anything abnormal and list any onscreen messages you get when the problem occurs 2 Callyour dealer and describe the problem Please have your manual product and any helpful information readily available 3 If your product is diagnosed as defective obtain RMA return merchandize authorization
3. 6 Power Management Setup Phoenix AwardBIOS CMOS Setup Utility Power Management Setup ACPI Function Enabled ACPI Suspend Type Run UGABIOS if 53 Resume Pouer Management Video Off Method Video Off In Suspend Suspend Type MODEM Use IRQ Soft ff by PWR BTIN PWRON After PWR Fail Wake Up by PCI card Power On by Ring Resume by Alarm 11 gt Enter Select PU PD Value F10 Save ESC Exit 1 1 Help F5 Previous Values F Optimized Defaults Note The Power Management Setup screen allows configuration of the sys as tem for effective energy savings while still operating in a manner consis tent with intended computer use ACPIFunction Enabled This item defines the ACPI Advanced Configuration and Power Management feature that makes hardware status information available to the operating sys tem and communicate PC and system devices for improving the power man agement ACPI Suspend S3 STR This item allows user to select sleep state state when the computer is in sus pend mode 1 POS The suspend mode is equivalent to a software power down S3 STR The system shuts down with the exception of a refresh current to the system memory Run VGABIOS if S3 Resume Auto This item allows the user to enable run VGA bios if system resume from S3 Power Management Min Saving This item allows user to select system power saving mode Min Saving Minimum power manage
4. Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features gt PC Health Status Advanced BIOS Features gt Frequency Control Advanced Chipset Features Load Setup Defaults Integrated Peripherals Power Management Setup F ge 2 aq PnPZPCI Configurati Enter Password Esc Quit FS Menu in BIOS Select Item FIR Save amp Exit Setup Note enable this feature you should first go to the Advanced BIOS Fea x tures menu choose the Security Option and select either System or E Setup depending on which aspects you want password protected Sys tem requires a password both to boot the system and to enter Setup Setup requires a password only to enter Setup A password may be at most 8 characters long 30 To Establish Password 1 Choose the Set Password option from the CMOS Setup Utility Main Menu and press lt Enter gt When you see Enter Password enter the desired password and press lt Enter gt At the Confirm Password prompt retype the desired password then press lt Enter gt Select Save to CMOS and exit type lt Y gt then lt Enter gt To Change Password ll Choose Set Password option from the CMOS Setup Utility menu and press lt Enter gt When you see Enter Password enter the existing password and press lt Enter gt You will see the Confirm Password prompt type it in again and press lt Enter gt Select Set Password again and at the Enter Pas
5. SBC Single Board Computer with Embedded Intel Atom N270 1 6 GHz Processor The DAC BT05 can support DDR2 memory up to 2GB has five USB 2 0 compatible ports Giga LAN 1000Mbps interface LVDS interface The DAC BT05 also supports two SATA and six COM ports Product Features General 000000 CPU Intel Atom Processor N270 1 6GHz System Chipset Intel 945GSE ICH7M BIOS AWARD 8 Mbit Flash BIOS System Memory DDRII 400 533 MHz SDRAM up to 2GB SSD Supports CompactFlash TYPE Watchdog Timer Single chip Watchdog 255 level interval timer setup by soft ware Battery Lithium V 210 mAH UO lO Interface 2 SATA Supports 150MB s one on I O board 1 x KB mouse 6 x RS232 2xRS 232 I O board 1 x LPT USB 6 x USB 2 0 compliant ports 2x USB ports on I O board Audio Line out Mic in Cash Drawer one RJ 11 connector 12V and 24V selectable Ethernet Chipset Intel 82583V Speed 10 100 1000 Mbps interface 1 x RJ45 Standard Compliant with IEEE 802 3 IEEE 802 3u IEEE 802 3x IEEE 802 ab Display Chipset Intel 945GSE Memory Size Up to 64 MB of dynamic video memory allocation Resolution CRT display Mode Supports QXGA Up to 2048 x 1536 LVDS display Mode Up to 800 x 600 18bits 1 3 1 3 1 Specifications Functional Specification Processor Intel Atom Processor N270 Intel Atom TM 270 at 1 6 GHz with 512 KB L2 ca
6. and low speed capable Port routing logic determines whether a USB port is con trolled by UHCI or EHCI Power Management ICH7M supports Full ACPI Advanced Configuration and Power Interface 2 0 Supports 1 S PCI CLKRUN and PME support SMI System Management Interrupt generation BIOS ICH7M supports Award 8M SPI Flash BIOS APM 1 2 ACPI 1 1 FWH Type Other Chipsets Graphic and Video Controllers 945GSE Intel 3 5 Gen Integrated Graphic Engine Supports QXGA Up to 2048 x 1536 LVDS Support 18 bit LVDS panel LVDS connector Hirose DF 13 type 20 pin CRT connector D SUB15 at coastline Intel 82583V Compliant with IEEE 802 3 IEEE 802 3u IEEE 802 3x IEEE 802 ab zii Support 1000Mbps Connectors Phone Jack RJ45 8P 90D F Fintek F81216DG 4E 4F Compatible UARTs with Data rates to 1 5Mbps Serial ports Support IRQ Sharing among serial ports Connectors SXCOM port via D Sub 9 CONN 1xCOM port on 2x5 wafer CONN 2xRS232 on IO Board Parallel port N A Keyboard Mouse connectors PS 2 Keyboard and Mouse interface Connector Mini Din 6P at coastline Cash Drawer Connector d one RJ11 12V and 24V selectable 1 3 2 Mechanical Specification 1 3 2 1 Dimension mm L200 mm W125 mm 1 3 3 1 3 3 1 1 3 3 2 1 3 3 3 1 3 4 1 3 4 1 1 3 4 2 1 3 4 3 1 3 4 4 Electrical Specification Po
7. item allows you respectively assign an interruptive type for IRQ 3 4 5 7 9 10 11 12 14 and 15 DMA Resources This item allows you respectively assign an interruptive type for DMA 0 1 2 3 4 5 6 and 7 PCIVGA Palette Snoop Disabled The item is designed to solve problems caused by some non standard VGA cards A built in VGA system does not need this function INT Pin 1 8 Assignment Auto This item allows the user to select the interrupt request IRQ assigned to a device connected to the PCI interface on your system Maximum Payload Size 4096 This item allows the user to adjust maximum TLP Transaction Layer Packet payload size 27 3 2 8 PC Health Status Phoenix uardBIOS CMOS Setup Utilitu PC Health Status Shutdown Temperature Disabled Item Help Ti gt e Move Enter Select PU PD Value F10 Save ESC Exit 1 1 Help F5 Previous Values F Optimized Defaults Note This PC Health Status page reports the thermal fan and voltage status of the board This page may vary according to the chipset installed Current CPU Temperature Show Only This item displays current CPU temperature FAN 1 Speed Show Only This item displays current system FAN s speed s VCC 2 5 V 5V 12V Show Only This item displays current CPU and system voltage 28 3 2 9 Frequency Voltage Control Phoenix AwardBIOS CMOS Setup Utility Frequency Voltage Control Auto Detect PC
8. number from your dealer This allows us to process your return more quickly 4 Carefully pack the defective product a fully completed Repair and Replacement Order Card and a photocopy proof of purchase date such as your sales receipt in a shippable container A product returned without proof of the purchase date is not eligible for warranty service 5 Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer Technical Support and Assistance 1 Visit the Advantech web site at www advantech com support where you can find the latest information about the product 2 Contact your distributor sales representative or Advantech s customer service center for technical support if you need additional assistance Please have the following information ready before you call Product name and serial number Description of your peripheral attachments Description of your software operating system version application software etc A complete description of the problem exact wording of any error messages Contents Chapter Chapter Chapter 1 k k N 2 1 2 2 2 3 3 3 1 3 2 General Introduction 1 INTO UCI p 2 Product Feature eae td ee aid 2 SPSCIICALOMS E 3 1 3 1 Functional Specification sees 3 1 3 2 Mechanical Specificati
9. the chipset Wake Up by PCI card Enabled This item allows user to defines PCI cards to wake up the system from the sus pend mode Power On by Ring Enabled This item allows user to define the system will resume by activating of modem ring Resume by Alarm Disabled This item allows user to enable and key in Date time to power on system Disabled Disable this function Enabled Enable alarm function to power on system Day of month Alarm 1 31 Time HH MM SS Alarm 0 23 0 59 0 59 26 3 2 7 PnP PCI Configurations Phoenix AwardBIOS CMOS Setup Utility PnP PCI Configurations Init Display First PCI Slot Item Help Reset Configuration Data Di ed Menu Level P Resources Controlled By PCI UGA Palette Snoop INT Pin 1 Assignment INT Pin 2 Assignment INT Pin 3 Assignment INT Pin 4 Assignment INT Pin 5 Assignment INT Pin 6 Assignment INT Pin 7 Assignment INT Pin 8 Assignment Maximum Payload Size tT e Move Enter Select PU PD Value F1 Save ESC Exit Fi General Help F5 Previous Values F7 Setup Defaults ga Note This PnP PCI Configurations option sets up the IRQ and DMA both PnP and PCI bus assignments Init Display First PCI Slot This item is setting for start up Video output from PCI or Onboard device Reset Configuration Data Disabled This item allow user to clear any PnP configuration data stored in the BIOS Resources Controlled By Auto ESCD IRQ Resources This
10. I Clk Spread Spectrum CPU Host SRC PCI Clock Ti e Moue Enter Select PU PD Value Fi0 Save ESC Exit Fi General Help F5 Previous Values F Optimized Defaults Note The Frequency Voltage Control screen controls the CPU host and PCI TE frequency The options on this page vary depending on the chipset items show up according to installed CPU capacities CPU Clock Ratio 6X This item enables users to set the CPU clock ratio by manually Auto Detect PCI Clk Enabled This item enables users to set the PCI Clk either by automatic system detection or manually Spread Spectrum Disabled This item enables users to set the spread spectrum modulation CPU Host SRC PCI Clock Defautl This item enables users to set the CPUhost SRC PCI clock 29 3 2 10 Load Optimized Defaults Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features gt PC Health Status Advanced BIOS Features gt Frequency Control fiduanced Chipset Features Integrated Peripherals Power Management I 2tup PnPZPCI Configura Saving Esc Quit F9 Menu in BIOS Select Item F18 Save amp Exit Setup Note Load Optimized Defaults loads the default system values directly from ra ROM If the stored record created by the setup program should ever E become corrupted and therefore unusable select Load Setup Defaults to have these default values load automatically for the next bootup 3 2 11 Set Password
11. Item F18 Save amp Exit Setup Standard CMOS Features This setup page includes all the features for standard CMOS configuration Advanced BIOS Features This setup page includes all the features for advanced BIOS configuration Advanced Chipset Features This setup page includes all the features for advanced chipset configuration Integrated Peripherals This setup page includes all onboard peripheral devices Power Management Setup This setup page includes all the power management items PnP PCI Configurations This setup page includes PnP OS and PCI device configuration PC Health Status This setup page includes the system auto detect CPU and system temperature volt age and fan speed Frequency Voltage Control This setup page includes CPU host clock control frequency ratio and voltage Load Optimized Defaults This selection loads optimized values for best system performance configuration Set Password Establish change or disable passwords Save amp Exit Setup Save CMOS value settings to CMOS and exit BIOS setup Without Saving Abandon all CMOS value changes and exit BIOS setup 3 2 2 Standard CMOS Features Phoenix uardBIOS CMOS Setup Utility Standard CMOS Features Date mm dd yy Item Help Time hh mm ss E gt IDE Channel Master gt IDE Channel 0 Slave gt IDE Channel 1 Master gt IDE Channel 1 Slave Drive A Video Halt On
12. NCTS6 RS232 NDTR67 HS232 NRI6 C WB 5x2V 2 00mm USB USB1 TERM SB34 C278 C279 zt 100uF 0 1uF 6 3V 16V Printer LTP1 ak 1 LPT SSTB 1 p_2 _SAFD LPT SPD0 ERR LPT SPD1 6 SINT LPT SPD2 8 SSI oc CA PD5 PD6 eist BH_13x2V_2 00mm SATA Connector SATA1 SATAO z TX SATAO z RX SATA 7V SATA Power SATA PWRI1 4VCC24 O WB_6V_2 5mm 13 2 33 Placement 2 3 1 Front Side LAN e USB Stack VGA COMStack Connector Connector Connector Cash Drawer Connector Poweron Switch COMBOX d Header q USB BOX Header MIC IN BOX Header 2 3 1 Rear Side 14 BIOS settings 3 1 3 2 BIOS Introduction AwardBIOS 6 0 is a full featured BIOS provided by Advantech to deliver superior per formance compatibility and functionality to industrial PCs and embedded boards Its many options and extensions let you customize your products to a wide range of designs and target markets The modular adaptable AwardBIOS 6 0 supports the broadest range of third party peripherals and all popular chipsets plus Intel AMD nVidia VIA and compatible CPUs from 386 through Pentium AMD Geode K7 and K8 including multiple proces sor platforms and VIA Eden C3 and C7 CPUs You can use Advantech s utilities to select and install feature
13. Tle lt Move Enter Select PU PD Value F10 Save ESC Exit 1 1 Help F5 Previous Values F Optimized Defaults Date The date format is lt weekday gt lt month gt lt day gt lt year gt Weekday From Sun to Sat determined and display by BIOS only Month From Jan to Dec Day From 1 to 31 Year From 1999 through 2098 t Time The times format in lt hour gt lt minute gt lt second gt base on the 24 hour time ct IDE Channel 0 1 Master Slave IDE HDD Auto Detection Press Enter for automatic device detection Halton This item determines whether the computer will stop if an error is detected dur ing power up No Errors The system boot process will not stop for any error All Errors Whenever the BIOS detects a non fatal error the system boot pro cess will be stopped All But Keyboard The system boot process will not stop for a keyboard error but will stop for all other errors Default value All But Diskette The system boot process will not stop for a diskette error but will stop for all other errors All But Disk Key system boot process will not stop for a keyboard or disk error but will stop for all other errors Base Memory Displays the amount of base or conventional memory installed in the system Extended Memory Displays the amount of extended memory above 1 MB in CPU s memory address map installed in the system Total Memory Displays the total system memory siz
14. che 437 pin FCBGA8 package FSB 533 MHz Bus Ratio 12 Manufacturing Technology 45nm Thermal Design Power 2 5 W Thermal Specification 90 C VID Voltage Range 90 V 1 100 V 0000000 Chipset 945GSE 945GSE GMCH Supports 2 GB maximum memory One 64 bit wde DDR2 SDRAM single channel Supports DDR2 400 DDR2 533 256 Mb 512 Mb 1 Gb and 2Gb DDR2 technology Memory Only x8 x16 DDR2 devices with 4 or 8 banks Support for DDR2 On Die Termination ODT Socket SODIMM Socket 1 200 pin SODIMM socket type 1 945GSE Graphic and Video d 3 5 See Ves Mem did Controllers NEEN Bower Guck Lu ogy 20 Intel DPST 20 intel Smart 2D Display Technology S2DDT Chipset ICH7M IDE Interface ICH7M supports Single independent IDE signal channel Supports one CF device H D Codec ALC886 I F ICH7M supports Support for HD codec f PCM i r tou Ko Y header 2 5 2 0 mm Concurrent PCI PCle Bus Controller ICH7M chip supports PCI 2 1 MHz PCI interface with 5 V tolerant inputs PCI Express 1 0a SATA Connector ICH7M supports Independent DMA operation on two ports Data transfer rates of up to 1 5 Gb s 150 MB s Operation of AHCI using memory space Several optional sections of the Serial ATA II SATA connectors Connector Serial ATA 1 7 pins 1 27 mm x 2 USB Interface ICH7M supports 5 USB 2 0 ports which are high speed full speed
15. d LAN devices Super IO Device This item enables users to set the Super IO device status includes enable Floppy COM LPT IR and control GPIO and Power fail status USB Device Setting This item enables users to set the USB device type 23 Phoenix uardBIOS CMOS Setup Utility SuperIO Device Onboard Serial Port 1 3F8 IRQ4 nboard Serial Port 2 SP 2 fiutoFlou Control Onboard Parallel Port Parallel Port Mode ECP Mode Use DMA Tle lt Move Enter Select PU PD Value F10 Save ESC Exit 1 1 Help F5 Previous Values F Optimized Defaults X Onboard Serial port 1 3F8 IRQ4 This item allows the user to adjust serial port 1 address X Onboard Serial port 2 2F8 IRQ3 This item allows the user to adjust serial port 2 address Onboard Serial port3 3E8 IRQ10 This item allows the user to adjust serial port 3 address Onboard Serial port 4 2E8 IRQ5 This item allows the user to adjust serial port 4 address Onboard Serial port 5 3E0 IRQ6 This item allows the user to adjust serial port 5 address Onboard Serial port 6 2E0 IRQ11 This item allows the user to adjust serial port 6 address Onboard Parallel Port 378 IRQ7 This item allows the user to adjust parallel port address and IRQ Parallel Port Mode SPP This item allows the user to adjust parallel port mode ECP Mode Use DMA 3 This item allows the user to adjust the ECP DMA resource 24 3 2
16. duanced BIOS Features gt Frequency Control Advanced Chipset Features Load Setup Defaults Integrated Peripherals Set Password Power Management S Quit Without Saving Y N N PnP PCI Configurat Esc Quit F9 Menu in BIOS Select Item FIR Save amp Exit Setup fibandon all Data Note Typing Y will quit the BIOS Setup Utility without saving any changes to CMOS i le Typing will return to the BIOS Setup Utility 32 Trusted ePlatform Services AD ANTECH Please verify specifications before quoting This guide is intended for reference purposes only All product specifications are subject to change without notice No part of this publication may be reproduced in any form or by any means electronic photocopying recording or otherwise without prior written permis sion of the publisher All brand and product names are trademarks or registered trademarks of their respective companies Advantech Co Ltd 2009
17. e 18 3 2 3 Advanced BIOS Features Phoenix AwardBIOS CMOS Setup Utility Advanced BIOS Features gt CPU Feature Press Enter Item Help gt Hard Disk Boot Priority Virus Warning CPU L1 amp L2 Cache CPU L3 Cache Hyper Threading Technology Quick Power On Self Test First Boot Device Second Boot Device Third Boot Device Boot Other Device Boot Up Floppy Seek Boot Up NumLock Status Gate AZO Option Typematic Rate Setting Security Option APIC Mode Ti gt e Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F Optimized Defaults Feature item allows the user to adjust CPU settings such as CPU ratio VID an Thermal and special features like XD flag Hard Disk Boot Priority This item allows the user to select the boot sequence for system devices such as HDD SCSI and RAID CPUL1 amp L2 Cache Enabled This item allows user to enable CPU L2 cache and ECC checking function CPU L3 Cache Enabled This item allows the user to enable disable CPU L3 cache Hyper Threading Technology Enabled This item allows the user to enable disable Hyper threading support for the Intel amp Pentium amp 4 processor with HT Technology Quick Power On Self Test Enabled This field speeds up the Power On Self Test POST routine by skipping re test ing a second third and fourth time The default setting is enabled First Second Third Other Boo
18. etting JP1 JP2 JP4 JP6 Jumper setting Default 4NCCS VCC12 MINIJUMPER 2 2 0mm JP1 1A 9 1 Hm a i FS1 RS232 NRI 5 6 25 20 Rs232 ORS232 CJ y BATE G na JP2 3 4 1 Dd M PH 3x2V S2 00mm i i Ee VCC12 MINIJUMPER 2 2 0mm 9 1A NRI2 20 5232 NRI2 C mr 00 NRI G JP4 3 4 1 SMD1612P1501F 24 PH 3x2V S2 00mm i KE HVCC12 MINIJUMPER 2 2 0mm 9 1 1A i ZZ DESEN NRI4 21 RS232 o RS232 Be JP6 3 4 1 00mm i VCC5 VCC12 MINIJUMPER 2 2 0mm E 2 9 1A 9 1 FS6 21 RS232_NRI6 i A RS232 NRI6 C SNRI6 pr PH 3x2V S2 00mm JP7 Cash Drawer Default Pin 1 Pin 2 JP7 1 JP7 1 2 1 VCC240 PH_3x1V_2 54mm MINIJUMPER 2 2 54mm 2 2 2 2 1 Connectors Connector list Table 2 9 Connector List MIC1 MIC in COMP1 COM USB1 USB LPT1 Printer SATA1 SATA Connector SATA PWR SATA power UPS1 UPS CN6 PCIEx8 DIMM1 Memory socket BH1 Battery holder CF2 CF Slot SW1 Switch Drawer Cash Drawer LAN1 RJ45 USB stack Connector CN2 COM VGA connector COM1 COM Stack Connector CN3 PS2 CN5 DC out DC IN1 DC In 2 2 2 Connector Settings Connector Pin Define Mic in MIC1 MIC1 WB 4V 2 0mm COM COMP1 COMP1 RS232_NDCD61 RS232 NDSR6 RS232 NRXD63 RS232 NRTS6 RS232 NTXD6 5 RS232
19. for OS 1 4 This item sets the operating system multiprocessor support version OS Select For DRAM gt 64 MB Non OS2 Select OS2 only if the system is running the OS 2 operating system with greater than 64 MB of RAM on the system 20 3 2 4 Advanced Chipset Features Phoenix AwardBIOS CMOS Setup Utility Advanced Chipset Features DRAM Timing Selectable By SPD Item Help CAS Latency Time DRAM RASH to CASH Delay DRAM RAS Precharge Precharge dealy tRAS System Memory Frequency SLP_S4 Assertion Width System BIOS Cacheable Video BIOS Cacheable Memory Hole At 15M 16M PCI Express Root Port Func On Chip Frame Buffer Size DUMT Mode DUMT FIXED Memory Size Boot Display Panel Type Ti gt e Move Enter Select PU PD Value F10 Save ESC Exit 1 1 Help F5 Previous Values F Optimized Defaults Note The Advanced Chipset Features screen controls the configuration of Tus the board s chipset register settings and performance tuning the options on this screen may vary depending on the chipset type It is strongly recommended that only technical users make changes to the default settings DRAM Timing Selectable By SPD This item enables users to set the optimal timings for items 2 through 5 system default setting of By SPD to follow the SPD information and ensure the system running in stable and optimal performance CAS Latency Time Auto This item enables users to set the timing delay in clock cyc
20. les before SDRAM start a read command after receiving it DRAM RAS to CAS Delay Auto This item enables users to set the timing of the transition from RAS row address strobe to CAS column address strobe as both rows and column are separately addressed shortly after DRAM is refreshed DRAM RAS Precharge Auto This item enables users to set the DRAM RAS precharge timing system default is setting to Auto to reference the data from SPD ROM Precharge delay tRAS Auto This item allows user to adjust memory precharge time System Memory Frequency Auto This item allows user to adjust memory frequency to improvement performance 51 54 Assertion Width 4 to 5 Sec This item allow user to set the SLP_S4 Assertion Width System BIOS Cacheable Enabled This item allows the system BIOS to be cached to allow faster execution and better performance 21 Video BIOS Cacheable Disabled This item allows the video BIOS to be cached to allow faster execution and bet ter performance Memory Hole At 15M 16M Disabled This item reserves 15MB 16MB memory address space to ISA expansion cards that specifically require the setting Memory from 15MB 16MB will be unavail able to the system because of the expansion cards can only access memory at this area PCI Express Root Port Func Press Enter This item allows the user to adjust the PCIE port to on off or auto On Chip Frame Buffer Size 8MB This item all
21. ment Suspend Mode 1 hr Max Saving Maximum power management Suspend Mode 1 min User Define Allows user to set each mode individually Suspend Mode Disabled or 1 min 1 hr 25 Video Off Method DPMS This item allows the user to determine the manner in which the monitor is blanked V H SYNC Blank This option will cause the system to turn off vertical and horizontal synchronization ports and write blanks to the video buffer Blank Screen This option only writes blanks to the video buffer DPMS Initial display power management signaling Video Off In Suspend Yes This item allows user to turn off video during system enter suspend mode Suspend Type Stop Grant This item allows user to determine the suspend type Modem use IRQ 3 This item allows user to determine the IRQ which the MODEM can use Suspend Mode 1 Hour This item allows user to determine the time of system inactivity all devices except the CPU will be shut off HDD Power Down Mode 15 Min This item allows user to determine the time of system inactivity the hard disk drive will be powered down Soft Off by PWR BTTN Instant Off This item allows the user to define the power button functions Instant Off Press the power button to power off instantly Delay 4 Sec Press and hold the power button for 4 sec to power off PWRON After PWR Fail Former Sts This item allows the user to select recovery after power fail function this func tion depends on
22. on ee 5 1 3 8 Electrical Specification esses 6 1 3 4 Environmental Specification sss 6 installation 7 JUmD8 S u 8 211 umole a 8 Table 2 1 Jumper list 0 8 2 1 2 Jumper Settings pe 8 iss uu us Qs dt on u a yayakuna 10 2 2 4 Connector gt ll lll Uu nnne nnns 10 Table 2 9 Connector List 10 2 2 2 Connector Settings 3 11 Placement ia 14 2 3 1 Front side 14 2 3 2 pion 14 BIOS S elli jJg u uuu uuu unus E BIOS Introduction 16 BIOS Setup mm aiii 16 SC WE NOT EE 17 3 2 2 Standard CMOS Features pp 18 3 2 8 Advanced BIOS Features pp 19 3 2 4 Advanced Chipset Features 21 3 2 5 Integrated Peripherals u u u 23 3 2 6 Power Management Setup pp 25 3 2 7 PnP PCI Configurations nn 27 3 2 8 Health Status u 28 3 2 9 Frequency Voltage Control 29 3 2 10 Load Optimized Defaults sees 30 3 211 Set PaSSWOIQ uiuit ade 30 3 2 12 Save amp Exit Setyup 32 3 2 18 Quit Without Saving Ne 32 General Introduction This chapter gives background information on the DAC BT05 Sections include Introduction Product Feature Specifications 1 1 1 2 Introduction The DAC BT05 is 3 5
23. ows the user to adjust on chip graphics of memory buffer DVMT Mode DVMT This item allows the user to adjust Intel s Dynamic Video Memory Technology DVMT BIOS provides three option to choose DVMT FIXED and Both DVMT FIXED Memory Size 128MB This item allows the user to adjust DVMT FIXED graphics memory size Boot Display LFP CRT This item allows the user to decide which display mode to use for the boot dis play Panel Type LFP1 800 x 600 18bits This item allows the user to adjust panel resolution Backlight Control 80 This item allow the user to adjust panel backlight 22 3 2 5 Integrated Peripherals Phoenix AwardBIOS CMOS Setup Utility Integrated Peripherals gt OnChip IDE Device Press Enter Item Help gt Onboard Device gt Superl0 Device gt USB Device Setting Tlee Move Enter Select PU PD Value F10 Save ESC Exit Fi General Help F5 Previous Values F Optimized Defaults Note The Integrated Peripherals screen controls chipset configuration for Tus IDE ATA SATA USB AC97 MC97 and Super IO and Sensor devices The options on this screen vary depending on the chipset X OnChip IDE Device This item enables users to set the OnChip IDE device status including IDE devices and setting PIO and DMA access modes Some chipsets support newer SATA devices Serial ATA ct Onboard Device This item enables users to set the Onboard device status includes enable USB AC97 MC97 an
24. s that suit you and your customers needs BIOS Setup The DAC BT05 system has AwardBIOS 6 0 built in which includes a CMOS SETUP utility that allows users to configure settings as required or to activate certain system features The CMOS SETUP saves configuration settings in the CMOS RAM of the mother board When the system power is turned off the onboard battery supplies the neces sary power to the CMOS RAM so that settings are retained To access the CMOS SETUP screen press the Del button during the power on BIOS POST Power On Self Test CMOS SETUP Navigation and Control Keys 1 gt lt l see se gt gt Move to highlight item lt Enter gt Select Item Main Menu Start Quit sequence SES Sub Menu Exit the current page and return to level above lt Page Up gt Increase the numeric value or make changes lt Page Down gt Decrease the numeric value or make changes lt F1 gt General help for Setup Sub Menu lt F2 gt ltem Help lt F5 gt Load Previous Values lt F7 gt Load Optimized Default lt F10 gt Save all CMOS changes 3 2 1 Main Menu Press the lt Del gt key during startup to enter the BIOS CMOS Setup Utility the Main Menu will appear on the screen Use arrow keys to highlight the desired item and press lt Enter gt to accept or enter the sub menu Phoenix AwardBIOS CMOS Setup Utility gt Standard CMOS Features Esc Quit Menu in BIOS Select
25. sword prompt enter the new password and press lt Enter gt At the Confirm Password prompt retype the new password and press lt Enter gt Select Save to CMOS and exit type lt Y gt then lt Enter gt To Disable a Password ll Choose the Set Password option from the CMOS Setup Utility main menu and press lt Enter gt When you see the Enter Password prompt enter the existing password and press lt Enter gt You will see Confirm Password type it in again and press lt Enter gt Select Set Password again and at the Enter Password prompt DO NOT enter anything just press lt Enter gt At the Confirm Password prompt again DO NOT type in anything just press lt Enter gt Select Save to CMOS and exit type lt Y gt then lt Enter gt 31 3 2 12 Save amp Exit Setup Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features gt PC Health Status Advanced BIOS Features gt Frequency Control Advanced Chipset Features Load Setup Defaults Integrated Peripherals Set Password Power Management PnP PCI Configura i a Saving Esc Quit FS Menu in BIOS Select Item F18 Save amp Exit Setup Save Data to CMOS Note Typing Y will quit the BIOS Setup Utility and save user setup values to rw CMOS D JE Typing will return to BIOS Setup Ulility 3 2 13 Quit Without Saving Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features gt PC Health Status fi
26. t Drive Hard Disk Sets boot priority for the hard disk CDROM Sets boot priority for CDROM USB FDD Sets boot priority for USB FDD USB ZIP Sets boot priority for USB ZIP USB CDROM Sets boot priority for USB CDROM LAN Sets boot priority for LAN Disabled Disables this boot function Boot NumLock Status This item allows the user to activate the Number Lock key at system boot Gate 20 Option Fast This item allows the user to switch on or off A20 control by port 92 19 Typematic Rate Setting This item allows the user to set the two typematic control items This field controls the speed of Typematic Rate Chars Sec This item controls the speed at which the system registers auto repeated key strokes The eight settings are 6 8 10 12 15 20 24 and 30 Typematic Delay Msec This item sets the key press delay time before auto repeat begins The four delay rate options are 250 500 750 and 1000 Security Option Setup System System requires correct password before booting and also before permitting access to the Setup page Setup System will boot but requires correct password before permitting access to Setup Default value APIC Mode Enabled This item allows the user to enable disable the Advanced Programmable Inter rupt Controller APIC is implemented in the motherboard and must be sup ported by the operating system it extends the number of IRQs available MPS Version Control
27. wer supply Voltage Voltage requirement with AT Power AT 24 Voc 5 Power Supply Current Supply Current ATX CPU Intel Atom N270 1 6 GHz XP Mode ATX 5V 12V Typical 1 90A 0 07 A Suspend 1 36 0 06 Load 2 38 0 09 Battery Typical Voltage 3 0 V Nomal discharge capacity 210 mAh Environmental Specification Operating Temperature Operating temperature 0 60 32 140 Tested under 60 C chamber temperature with 0 23 m s air flow Operating temperature 20 80 Only for wide temp SKU PCM 9361FZ 1GS6A1E Operating Humidity Operating Humidity 10 90 Relative Humidity non condensing Storage Temperature Standard products 0 60 C Storage temperature 20 70T Storage Humidity Standard products 0 60 C Relative Humidity 95 60C H W installation This chapter explains the setup procedures of the DAC BT05 hard ware including instructions on setting jumpers and connecting peripherals switches indicators and mechanical drawings Be sure to read all safety precautions before you begin the installation procedure 2 1 Jumpers 2 1 1 Jumper list Table 2 1 Jumper list CMOS1 CMOS REST1 RESET LPC1 LPC JP1 2 4 6 COM Port selection JP7 Cash Drawer 2 1 2 Jumper Settings CMOS1 CMOS Jump Setting CMOS1 Jumper Setting Normal Default Clear CMOS P MOS1 RTC_RST PH_3x1V_2 54mm JP1 2 4 6 COM Port S
Download Pdf Manuals
Related Search