HeritaGe User manUal
Contents
1. Heritage swim spas and spas user manual HERITAGE USER MANUAL POSITION SPA When deciding where to position your Heritage spa conscider how you are going to get access in and out of your spa Where you are going to place your cover when not in use and is there enough room to access all equipment for servicing of your swim spa Your Heritage spa needs to be positioned so that you have clear access to all equipment Which is located at the two short ends of the swim spa this can be accessed by removing the doors of the cabinet if you are unsure please contact Heritage spas for assistance SITE PREPARATION Your Heritage spa has been designed to evenly support the weight of the spa water and the users The swim spa requires a good solid level foundation to sit on if the foundation is not adequate the spa may stress and cause damage to the spa that will not be covered by war ranty Surface and slab requirements It is recommended that all slabs or paving is at least 200 mm bigger than the swim spa base size to allow for repositioning and foundation strength Ensure that the concrete has cured for at least week before placing your spa in place A water filled spa can weigh as much as 8500kg ELECTRICAL INFORMATION In all cases the electrical supply to your new swim spa will require a dedicated circuit with no other power appliance or socket sharing the power The electrical supply must be installed by a qualified electrian to comply wit2. GE SPAS UK amp EUROPE FERIA GY SPAS _ T
3. S Headrests can be removed quite easily and cleaned with warm soapy water If you have ozo ne fitted to your spa the headrests may become discoloured over time this is quite natural due to the presence of ozone Try and remove headrests as little as possible When entering the spa do not slide over headrest or use as a body support The lugs are rated at over Okg but the headrest is only foam and rips with excess pressure Headrest will continue to last if treated properly and are NOT COVERED BY WARRANTY IF TREATED INCORRECTLY SCUM LINES Scum lines are caused by oils and minerals from the bodies of users To clean these scum lines use Poolfast Tile amp Vinyl Cleaner on a rag to wipe clean Any similar product for pools or spas may be used for this purpose WARNING ALWAYS TURN POWER OFF BEFORE REMOVING FILTERS AND DRAINING YOUR SPA Heritage swim spas and spas user manual 6 DRAINAGE Your Heritage spa comes with a drain valve which can be connected to a garden hose this is located under the recliner Or simply drain by siphoning water out by a garden hose DRAIN VALVE FILTER CLEANING For Clean water you should remove your filters every fortnight and wash under the garden hose with full pressure until all dirt and grit is removed Once a month soak filters in a cartridge filter cleaner degreaser This will increase the life of your filters WARNING ALWAYS TURN POWER OFF BEFORE REMOVING FILTERS AND DRAINING YOUR SPA HERITA
4. educe the need to bleed the pump With heavy bather loads only fill to about 30mm below water line This is to compensate for the amount of people in the spa To remove filters first pull on locking clips and pull up to remove filter face then pull up on front of leaf basket to remove To remove filters simply feed up by hand and out threw the filter box opening Refer to picture below for filter assembly Water level Location lugs atrear Clips down at front x z w e n riy T 7 5 Sai i y kp el X i Locking clips Leaf basket Filters Heritage swim spas and spas user manual BLEEDING CIRC PUMP WHERE APPROPRIATE After filling your swim spa you may need to bleed the circ pump This is done by turning the barrel union on top of pump You should hear air escaping from the pump When you see water draining thru the barrel union re tighten the union being careful not to over tighten casing the nut to cross thread BLEEDING JET PUMP When you have the power turned on press the pump button on the touch pad You should start to see water coming out of the jets with in a few seconds If water is not present after 5 10 seconds turn pump off Turn the barrel union anti clockwise on pump and you should hear air then water come out of the barrel union Re tighten the barrel union being careful not to over tighten press the pump button again if there is no water coming from jets repeat till all air is released fro
5. h all regulations and standards specified by the electrical authority The Cyclone Hurricane and Monsoon are all to be wired at a minimal of 32 amp single phase The Hurricane and Monsoon can be upgraded to 45 amp single phase to disable the load shedding this will allow for all pumps to operate at the same time For all swim spas out side of Australia please seek advice from your local dealer to ascertain what power requirements are required for your application Please note that in Europe that a 3 phase connection may be available VENTILATION If your Heritage spa is enclosed please ensure that there is adequate ventilation Swim spas produce considerable amounts of condensation which could damage walls and ceilings Heritage swim spas and spas user manual FILLING YOUR SPA Before filling your spa please ensure that all barrel unions are tight The barrel unions are two big plumbing nuts located at the wet end of each pump these can come loose during transport Also check that all shut off valves to the pumps are fully open Please refer to picture below Shut off valve Barrel unions When filing your spa the best way to do this is to remove the filters and place the hose in the housing This could take sometime depending on water pressure Start to fill until the water naturally flows in to the filter assembly then refit the filters and fill to water line as marked on filter face plate this will push the air out of the pumps and r
6. m pump and jets are all working ADJ USTING J ET PRESSURE To adjust the water pressure to fully open rotate the jet face in a clock wise direction until you come to a stop Io reduce pressure turn the jet face anti clock wise direction till the jet face stops VWhen the jet is fully closed you will still find a small amount of water coming from the jet this is perfectly normal this will stop pump damage if all jets are turned off Off On REMOVING AND REPLACING YOUR JET FACE To remove the jets simply turn the jet to the fully open position then turn a little more while pulling the jet out the jet will now come out of its housing To replace your jet place the jet back in the housing and turn the jet with the palm of your hand until the jet clicks back in to the housing Jets can become quite stiff due to dirt and grit and may be hard to loosen follow this proce dure they will not break but may take extra force if this is the case Heritage swim spas and spas user manual AIR CONTROLS Air controls are used to control the amount of air to be mixed with the water coming out of the jets to give you a harder or softer feeling On Off DIVERTER VALVE Some spas have diverter valves which transfer water from one area of the spa to another If you find they will not move or become stiff they need to be removed for cleaning Turn off power to spa lift off the handle of the diverter By carefully holding the outside of the diver
7. ter and screwing anti clockwise you should then be able to lift out the centre gate from the housing Wipe out any dirt and grit from housing and wipe inside the housing with a damp rag Hand sand any scratches with light sandpaper lubricate with a silicone based lubricate or rubber o ring conditioner and re assemble Be careful not to force diverter valves when they are stiff as handle can be broken amp is not covered by warranty Air controls zy 70 AF p fate Diverter valve Heritage swim spas and spas user manual AIR CONTROLS DIVERTER VALVE COVER Always take care of your spa cover It is not designed for sitting walking or lying on If your cover needs cleaning it can be removed from the spa washed with warm soapy water then hosed off Apply a vinyl protection that is readily available at any automotive store This pro tects your cover and maintains its appearance NOTE There are 2 holes on the underside of your cover for condensation purposes DO NOT cover these 2 holes or use them as handles You will receive a warranty card with your cover this must be filled out and sent to the cover manufacturer for your cover warranty Timber cabinet You can maintain or rejuvenate the appearance of your cabinet by giving it a coat of clear decking oil once a year We recommend Cabot s All Purpose Clear Decking Oil or Wattyl western red cedar but there are other similar and equally good products on the market HEADREST
Download Pdf Manuals
Related Search