Model HLAC150 Quick Start Guide
Contents
1. You may ALARM SETUP TEST in the user s manual non erie dod KEEP THIS QUICK START GUIDE IN A SAFE PLACE Doc LTQSG150E130713 STEP 3 SETTING THE CLOCK Buttons on the top of the Lifetone HL 1 On the time display 12 hr is flashing To select 24 hour time press or Press SET CLOCK The hour will flash To change the hour press or O O O Press SET CLOCK The minute will flash To change the minute press or PR ON OFF HI LO SET ALARM SET CLOCK Press SET CLOCK The year will flash To change the year press or nn A W N Press SET CLOCK The small M and D will flash To change to a day first display of the date press or 6 Press SET CLOCK The month will flash To change the month press or 7 Press SET CLOCK The day will flash To change the day press or 8 Press SET CLOCK The E for English will flash To change to Spanish or French press or Press SET CLOCK again 9 The clock will show the day of the week to the right of the date If you prefer to display the year instead press SET CLOCK again YEAR LANGUAGE DAY OF WEEK NOTE Any time that you need to reset the clock press and hold SET CLOCK until the flashing 12hr appears and repeat all parts of STEP 3 MONTH OR f N DAY FIRST MONTH DAY O OR MO STEP 4 SETTING THE WAKE UP ALARM AE SA 1 Ifthe wake up hour is not flashing press SET ALARM unt2. you want detected If you have interconnected alarms use the nearest one 3 Press and hold the test button on the smoke alarm until the Lifetone HL alarm sounds Between 2 and 6 smoke alarm T3 cycles groups of 3 beeps will be required This takes about 10 to 30 seconds 4 When the Lifetone HL alarm sounds and FIRE appears on the screen Q Ahi the test has been successful T3 ALARM SIGNAL 5 To stop the alarm press the red TEST SILENCE button on the back of the clock wb bbbiag FLASHING cat A Smoke alarm has been detected 6 If all tests are passed the 12 hr time display option will flash on the screen and you may now set the clock Go to STEP 3 Important warning If you have First Alert talking alarms see section IV OPERATING INSTRUCTIONS in the HLAC150 User s Manual Press TEST SILENCE button to silence alarm NOTE If the clock is flashing all segments as shown below and beeping at short intervals your smoke alarm was not detected or is not compatible with the LIFETONE HL VD mn siase SS BEEP ABBE IBE Beles SS ast Unplug the clock and remove one battery Repeat the setup beginning with STEP 1 POWERING THE PRODUCT You may need to choose a closer smoke alarm If the setup test fails again the smoke alarm may not be compatible Unplug the clock and remove the batteries See the section titled UNSUCCESSFUL SMOKE Suecesstultest
3. LIFETONE HL BEDSIDE FIRE ALARM AND CLOCK 4 D Cell Alkali HLAC150 Bed Shaker Batteries HLAC150 User s Manual PLACE THE LIFETONE HL NEXT TO YOUR BED WITH THE SPEAKER FACING THE PILLOW STEP 1 POWERING THE HLAC150 Remove battery oor 1 Remove the battery door located on the back of your clock 2 Insert four D cell alkaline batteries as shown in the illustration at right ke AT ue matching the polarity and signs in the open compartment 3 Replace the battery door securely A flashing TEST on the screen tells you the batteries are installed correctly 4 Plug the Lifetone HLAC150 into an electrical outlet near your bedside Do not use an outlet controlled by a wall switch 5 You may plug the bed shaker in on the back of the clock now Install 4 D Cell or at any time after it has been set up Alkaline Batteries Plug In ovat The word TEST will now be flashing on the screen Go to STEP 2 ao Sica NOTE The batteries are for backup in the event of a power outage only The HLAC150 is not meant to operate on batteries alone STEP 2 SETUP WITH YOUR SMOKE DETECTOR Press TEST SILENCE 1 The word TEST is flashing on the screen Press the red TEST SILENCE button on button to start the test the back of the clock The word TEST will stop flashing for 30 to 50 seconds 2 When TEST starts flashing again locate the most distant smoke alarm
4. e clock for S 2 seconds and release it That starts a manual self test that will display TEST for 10 to 20 seconds sound the fire alarm once and retrain the clock to operate without a bed shaker On BEEP Bed shaker ERROR Bed shaker unplugged PLEASE READTHE USER S MANUAL COMPLETELY AND THOROUGHLY FOR O i le FURTHER DIRECTIONS PRODUCT FEATURES AND WARRANTY INFORMATION TECHNOLOG Y NOTE Any time that you want to restore use of the bed shaker simply plug it in For more information go to www lifetonesafety com 800 Research Parkway Suite 339 or call Customer Service 1 800 648 7923 Oklahoma City OK 73104 MODEL HLAC150 KEEP THIS QUICK START GUIDE IN A SAFE PLACE Doc LTOSG150E130713
5. il the hour starts flashing Release SET ALARM To set the hour press or 2 Press SET ALARM The minute will flash To set the minute press or 3 Press ON OFF to enable or disable the wake up alarm The bell icon at lower left will appear or disappear to indicate whether the alarm is active or inactive You can adjust the volume of your wake up alarm to high or low with the HI LO slider switch on top If there is a fire emergency the alarm will sound at maximum volume NOTE Any time that you need to reset the wake up alarm time press and hold SET ALARM until the hour is flashing and then repeat all parts of STEP 4 TROUBLESHOOTING ERROR MESSAGES Batteries If the clock is flashing BATT and beeping at one minute intervals the batteries were not installed were installed with the wrong polarity or are below the required voltage Remove and insert them again or replace them if necessary Be sure to match the polarity and signs in the battery compartment To keep the setup with your smoke alarm leave the clock plugged in while you change batteries sl Yy Bed shaker If the screen is flashing beds and the clock beeps the bed shaker has come unplugged Seat the bed shaker plug firmly into the jack on the back of the clock NOTE If you decide you don t want to use the bed shaker after it has been installed an unplug the bed shaker Then press the red TEST SILENCE button on the back of th
Download Pdf Manuals
Related Search