Megapixel Indoor Digital Camera (With Buttons) User`s Manual
Contents
1. Function Item Name HDC HF3200P N Configuration Type COM Setup COM No COMO01 Baud rate 9600 Parity None Data bit 8 Stop bit 1 Current status N A Parameter Color Brightness 50 Contrastness 50 Hue 50 Saturation 50 BLC Disable Exposure Shutter Auto Gain 50 Aperture Auto Exposure Compensation 0 Mirror Disable Negative Video Disable WB Auto Day night mode Auto Sharpness 7 Scene Setup Cloudy Indoor Note Please press the Reset button for 5 seconds to restore the factory default setup if the device can not work properly or it can not boot up 2 Framework 2 1 Rear Panel This series digital camera real panel is shown as below See Figure 2 1 000 O RESET AC 24V DC 12V Figure 2 1 Please refer to the following sheet for detail information Interface Name Connector Function AC 24V DC 12V Power port e Power port e Input 12V DC or AC 24V STATUS Red light 9 e The red light is on Indication Light when the system is working properly ltflashes when the system is upgrading Green light Y Yellow light e Hardware indication light It is on after the hardware loaded successfully e Software indication light It is on after the software loaded successfully2. IN Reserved port I O port N A NO GND Alarm input ground end A RS485 port RS485_A port It is to control the 458 tool to set the video parameter B RS485_B port It is to control the 458 tool to set the video parameter NA It is to detect IR light signal RX Reserved port N A TX G RESET RESET button Restore factory default setup When system is running normally power indication light is red press the RESET button for at least 5 seconds The yellow indication light flashes and system can restore factory default setup HD SDI Send out the SDI video stream conforming to the HD SDI specifications VIDEO OUT Analog output Analog video output stream Button Left right up down OK OSD button It is to control OSD menu 2 2 Side Panel GND Please make sure the device is securely earthed to prevent the thunderstorm strike Please refer to the following interface for side panel dimension information The unit is mm See Figure 2 2 10 Figure 2 2 2 3 Front Panel Please refer to the following interface for front panel dimension information The unit is mm See Figure 2 3 Figure 2 3 3 Installation 3 1 Lens Installation 3 1 1 Auto Aperture Lens Please follow the steps listed below for auto aperture lens installation The interface is shown as in Figure 3 1 and Figure 3 2 Remove the lens
3. L 23a gt Slotted TMAA A Screwdriver SRE puss we Figure 3 4 3 2 2 IR Light Connection Please refer to the following figure for IR synchronization input signal information See Figure 3 5 Please connect the signal cable to the NA port of the rear panel and ground cable to the G port of the rear panel When the external IR light is on the signal cable from the board outputs the 3 3V 1mA It outputs the OV when the IR light is off GND Signal Cable IPC Connection Power Supplying to the IR Light Figure 3 5 14 4 HDC Configuration Tool 4 1 Overview You can use HDC configuration tool to set the device parameter and upgrade the system 4 2 Operation Double click the 485Configs exe icon you can see an interface is shown as in Figure 4 1 In the device interface you can view COM setup parameter setup OSD upgrade information and etc The parameter interface is shown as in Figure 4 1 22 ADC Configtool V1 0 COM Setting con Baud Rate 110000 gt Parity Bit OE gt DataBit fp gt stopsit f Current Status PP taras Open COM Paraneter osD Upgrade Color Brightness 0 I Contrastness 0 Hue 0 Saturation 0 M Bie j0 Exposure FPGA Version Shutter z Aa RE I Gain 0 Aperture ka Exposure Compensation zj Software EE Default Mirror Negative Y B v Trigger Sharpness y Def Day Night z Scene Setting y Save Figure 4 1
4. e ade do e do 8 2 2 Side Pale le eo cht Et OD Det NN NA 10 2 3 Front Panel lisent isa ns damian ads 11 ON installation ssena a e o o el A chore 12 3 1 LensIistallation 2a riada a SEAN EEE BES LENG OE a SELES 12 3 1 1 AO PAS O cs i ht Lt ne ae a ee ea 12 Seb Manual Lenses 3 cece i fei RG EAE BS I LSE LAG 12 By 1 3 REMOVE LGMS wstck E 13 3 2 HO POM ich O cc cl a mest ay 13 3 21 VO Port CONNECTION sennen Ss eee iocdens 13 dz IR IGNORAR 14 4 HDC Configuration TOO sta tdi 15 4 1 OVERVIEW a a sized a aa 15 4 2 Operaatio Nese ina EA O E A E i taainty 15 Appendix Toxic or Hazardous Materials or Elements o oooooonoccincononinoccocccononononcnonncanocnnonnnonos 19 1 General Introduction 1 1 Overview This series digital camera conforms to the HD SDI specifications It supports high speed video signal almost no delaying in the transmission The HD SDI interface adopts the coaxial cable and uses the BNC port as the cable standard This series product has the megapixel definition and supports the DC 12V AC 24V power It supports analog output and OSD button 1 2 Feature Dat e Adopt coaxial cable Use the BNC port as the cable standard ata Transmission e Support peripheral equipment connection via the RS485 port each Peripheral peripheral equipment control protocol and interface can be set freely Equipment Power e External power adapter Support DC 12V AC 24V power supply e Day Night mode auto swi
5. protection cap of the device and then line up the lens to the proper installation position Turn clockwise until the lens is fixed firmly Insert the lens cable socket to the auto lens connector in the side panel Loosen the screw near the focusing ring and then turn counter clockwise to move the focusing ring out for several millimeters Now you can focus manually and check the video is clear or not If you can not see the clear video you can adjust via the flange back After you completed the focus setup fix the screw firmly Fasten the focusing ring Now the installation completed Figure 3 2 3 1 2 Manual Lens Install C type lens Remove the lens protection cap from the device 12 e Install the C CS adapter to the camera Turn clockwise to secure against the focusing ring firmly e Line up the C lens to the installation position of the C CS adapter Turn clockwise to fix the lens e Use slotted screwdriver to fasten the screw near the focusing ring and then turn counter clockwise to move the focusing ring out for several millimeters Now you can focus manually and check the video is clear or not If you can not see the clear video you can adjust via the flange back e After you completed the focus setup use the slotted screwdriver to fix the screw firmly Fasten the focusing ring Now the installation completed Install CS type lens e Remove the lens protection cap from the device e Line up the CS lens to the lens instal
6. 8 Appendix Toxic or Hazardous Materials or Elements Component Name Toxic or Hazardous Materials or Elements Pb Hg Cd Cr VI PBB PBDE Circuit Board Component o o o o o o Device Construction Material o O O o O O Wire and Cable O O O O o O Power Adapter O O O O O O Packing Components o o o o o o Accessories O O O O O O O Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ T11363 2006 standard X Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ T11363 2006 standard During the environmental friendly use period EFUP period the toxic or hazardous substance or elements contained in products will not leak or mutate so that the use of these substances or elements will not result in any severe environmental pollution any bodily injury or damage to any assets The consumer is not authorized to process such kind of substances or elements please return to the corresponding local authorities to process according to your local government statutes Note e This user s manual is for reference only Slight difference may be found in user interface All the designs and software here are subject to change without prior written notice If there is any uncertainty or controversy please refer to the fina
7. Megapixel Indoor Digital Camera With Buttons User s Manual Version 1 0 Welcome Thank you for purchasing our digital camera This user s manual is designed to be a reference tool for your system Please read the following safeguard and warnings carefully before you use this series product Please keep this user s manual well for future reference Important Safeguards and Warnings 1 Electrical safety All installation and operation here should conform to your local electrical safety codes The power shall conform to the requirement in the SELV Safety Extra Low Voltage and the Limited power source is rated 12V DC or 24V AC in the IEC60950 1 Before you replace the SD card please unplug the power cable and then remove the shell We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation We are not liable for any problems caused by unauthorized modification or attempted repair 2 Installation Do not apply power to the camera before completing installation Do not put object on the camera 3 Environment This series camera should be installed in a cool dry place away from direct sunlight inflammable explosive substances and etc The working temperature ranges from 10 C to 55 C Please keep it away from the electromagnetic radiation object and environment Please keep the sound ventilation Do not allow the water and other liquid falling into the c
8. The OSD interface is shown as in Figure 4 2 S ADC Config tool V1 0 COM Setting com v Baud Rate v Parity Bit WWE Data Bit v Stop Bit y Current Status E Open COM Paraneter OSD Upgrade Enter Menu Figure 4 2 The upgrade interface is shown as in Figure 4 3 15 3 ADC Configtool V1 0 COM Setting com HI y Baud Rate Parity Bit gt Data Bit x Stop Bit Current Status Open COM Paraneter osD Upgrade Current status Parameter Brightness Set the brightness value to adjust the video bright and Setup dark level The value ranges from 0 to 100 Contrastness e It includes two options Enable disable You can check the box to enable the contrastness function After you enabled this function you can set the different value to control the contrastness The value ranges from 0 to 100 Please note the BLC function and the contrast function can not be valid at the same time ranges from 0 to 100 The value ranges from 0 to 100 BLC The BLC has three options manual auto disable You can check the box to select the corresponding mode In the manual mode the value you set here is the actual backlight value In the auto mode the value ranges from O to 100 according to the actual environments In the disable mode the BLC function is disabled The value ranges from 0 to 100 Upgrade File Browse Checksum __Reboot Upgrade Process Wea jE Figu
9. amera Thunder proof device is recommended to be adopted to better prevent thunder The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera 4 Daily Maintenance Current series camera has no power button Please unplug all corresponding power cables before your installation Do not touch the CCD or CMOS part you can use the blower to clean the dust on the surface of the lens You can use the dry cloth with some alcohol to clear if necessary Please keep the dustproof cap back to protect the CCD or CMOS part if the camera does not work for a long time If there is too much dust on the housing please use the water to dilute the mild detergent first and then use it to clean the device with the clear dry cloth Finally use the dry cloth to clean the device 5 Accessories Please open the accessory bag to check the items one by one in accordance with the list below Contact your local retailer ASAP if something is missing or damaged in the bag Accessory Name Amount Camera Unit C CS adapter Quick Start Guide CD Table of Contents f General IntroductiOn iris ardid dt dd 6 1 1 COVERVIC Wr nasales iria 6 1 2 O O ER TR 6 1 3 Spe cificatlonS a oo 6 M3 PERMONMANCE 26 tdt batida 6 1 3 2 Factory Default Setup aii a A A T 2 RaMeWoO Kit a la otal tables e ado Lats lorca AE 8 2 1 Rear Panel tica o e gs edita O e do sto Edo to
10. can set compensation the corresponding value to adjust the video total brightness FPGA version Others Mirror It is the pan rotation You can check the box to enable this function Otherwise it is in normal mode Negative It is to turn the bright part to the dark part and turn the video dark part to the bright part You can check the box to enable this function Otherwise it is in normal mode WB It includes disable auto sunny cloudy home office night customized In the customized mode you need to put a white paper before the lens and then click the Trigger button Sharpness It is to set the video sharpness level There are total 16 levels Day night It includes day night auto mode Inthe auto mode system automatically sets the day or night mode according to the current environments Inthe day mode the video is color e Inthe night mode the video is black and white Scene setting You can select the corresponding scene mode according to the various environments Default Restore system default setup Save Go to the main menu Use the up down button to the corresponding item and then use the left right button to adjust the parameter System upgrade Select the upgrade file and update the system For the hardware upgrade process it may take 25 minutes 0 U The OSD setup interface is shown as in Figure 4 4 AEC 0 a ATC Open WB Auto DA Day BLC Close Figure 4 4 1
11. l explanation of us Please visit our website for more information 19
12. lation position of camera focusing ring Turn clockwise to fix the lens e Use slotted screwdriver to loosen the screw near the focusing ring and then turn counter clockwise to move the focusing ring out for several millimeters Now you can focus manually and check the video is clear or not If you can not see the clear video you can adjust via the flange back e After you completed the focus setup use the slotted screwdriver to fix the screw firmly Fasten the focusing ring Now the installation completed 3 1 3 Remove Lens Please follow the steps listed below to remove lens The interface is shown as in Figure 3 3 e Turn the lens counter clockwise and then remove it from the camera e Unplug the auto lens cable socket from the auto lens connector If you are using the manual aperture lens please skip to the following step e fthere is no lens please put the lens protection cap back to protect the CCD Figure 3 3 3 2 1 0 Port 3 2 1 I O Port Connection Install Cable Please follow the steps listed below to install the cable See Figure 3 4 Use the small slotted screwdriver to press the corresponding button of cable groove Insert the cable into the groove and then release the screwdriver 13 Remove Cable Please follow the steps listed below to remove the cable Use the small slotted screwdriver to press the corresponding button of cable groove Remove the cable out of the groove and then release the screwdriver o
13. re 4 3 You can refer to the following sheet for detailed information Item COM Setup COM Select the corresponding COM number Baud rate Default value is 9600 Read only Parity Data bit Default value is 8 Read only Stop bit Default value is 1 Read only Please note the BLC function and the contrast function can not be valid at the same time Exposure Shutter It is to set the shutter time It includes the following modes e Auto System auto adjusts the shutter time according to the current environments Manual 1 3 1 6 1 50 1 120 The shutter time 16 is 1 3 1 6 1 50 1 120 Customized zone After you selected current mode you can see there is a period setup interface System can auto adjust in the period you specified Customized value After you selected the mode you can see the time period setup interface You can input the shutter value in the current interface Gain It includes two modes auto manual You can check the box to select the corresponding mode e Inthe manual mode your input value is the actual value e Inthe auto mode the value ranges from 0 to the setup value according to the actual environments Aperture It includes two options auto no auto Inthe auto mode system can automatically adjust the best aperture value according to the current environments Inthe non auto mode the aperture is all open Exposure There are 15 levels ranging from 7 to 7 You
14. tch ICR switch e Backlight compensation screen auto split to realize backlight Assistant compensation to adjust the bright Function e Support auto iris function e Support OSD button e Support analog output 1 3 Specifications 1 3 1 Performance Please refer to the following sheet for camera performance specification HDC HF3200P N 3 2 0 Main High performance processor lt Processor 1 2 9 inch CMOS Pixel 1920 H 1080 V TA Support day night mode switch and IR CUT at the same time Auto Iris DO drive O oS SoS SS Gain Control Fixed Auto White Balance Manual Auto Manual Auto It ranges from 1 50 to 1 10000 Mode e PE Conform to the SDI specifications SMPT274 292 protocol Video Bit Rate PAL 1920 1080 25fps NTSC 1920 1080 30fps Video Mirror Support S o e U o E 3 Negative Video Support Video Setup Support parameter setup such as brightness contrastness Information Lens Reset Hardware Resetbuton O O OC O OSOS RS485 Port Set video parameter Power SupportAC 24V DC 12V power Power Consumption 7W MAX 5W MAX when the ICR switch Working 10 C 60 C Temperature Dimensions 70x63 2x149 5 OOOO Weight E 1 3 2 Factory Default Setup Please refer to the following sheet for factory default setup information 28J19 u XNV Q 9 3 gt 5 U o o 3 gt
Download Pdf Manuals
Related Search