Home

Digital Photo Printer

1. Supplied Documentation The product comes with the following documentation Instruction Manual this document The Instruction Manual is aimed at owners of the product and contains detailed information about the following topics nstallation e Setup e Printing image data stored on memory cards e Troubleshooting Basic Operation Guide PDF The Basic Operation Guide file contains simple instructions and information about the topics listed below You should print out parts of this file as necessary and post them near the product for user guidance How to print photos in Full mode aimed at customers How to print photos in Quick Print mode aimed at customers e Maintenance aimed at shop personnel Printer Driver Installation Guide PDF The Printer Driver Installation Guide explains how to install and use the printer driver for the unit on a computer Adobe Photoshop Plug in Module User s Guide PDF The Adobe Photoshop Plug in Module User s Guide explains how to install the Photoshop plug in and how to use Photoshop to create templates for prints with borders Connection Manual to Job Ticket Printer PDF The Connection Manual to Job Ticket Printer explains the steps involved in connecting the UP CRIOL to a commercially available thermal receipt printer and printing job tickets Trademarks The following words are trademarks of their respective owners e Memory Stick MagicGate
2. ca 5 C ee When you insert the SmartMedia card into the unit it is automatically detected Removing the SmartMedia card When you see a message that prompts you to remove the SmartMedia card first push the SmartMedia card until you hear a click then pull it out To prevent losing valuable data or damaging the SmartMedia card never remove the SmartMedia card from the slot until the message prompts you to remove it Using a SD Card MultiMediaCard Inserting the SD Card or MultiMediaCard With the notch on the SD Card or MultiMediaCard away from you and to the right completely insert the card into the slot When you insert the SD Card or MultiMediaCard into the unit it is automatically detected Removing the SD Card or MultiMediaCard When you see a message that prompts you to remove the SD Card or MultiMediaCard first push the SD Card or MultiMediaCard until you hear a click then pull it out To prevent losing valuable data or damaging the SD Card or MultiMediaCard never remove the card from the slot until the message prompts you to remove it When using a miniSD Card always use a designated miniSD Card adapter There is a risk that you will not be able to eject the miniSD Card if you insert it into the card slot without an adapter Setting Memory Cards uoneJedo p Je deuD 33 uonejedo p 18 1dEUD 34 Using a xD Picture Card Inserting the xD Picture Card With
3. Print Order No Print Size Quantity Printable Sheet Quantity Estimated Print Time When the password file is read and printing starts remove the memory card containing the password file Insert the memory card containing the password file after the password confirmation screen appears If the memory card 1s already inserted when the screen appears the password file will not be read Be sure to insert the memory card with each printing Printing From a Computer When a USB cable is used to connect the unit to a computer data sent from the computer can be printed out using this unit When the USB cable is plugged in the indication PC MODE is shown on the display of the unit In this condition the touch panel is inactive To print from a computer you need to access the System tab on the administration screen and set PC Connection to ON Installing the Printer Driver If the unit is to be controlled from a computer you must install the supplied printer driver on the computer before connecting the unit to the computer for the first time For details on installation refer to the installation guide and the Readme file on the supplied CD ROM The supplied printer driver does not support printing via a network Connection to a Computer To control the unit from a computer you must connect the unit to the computer using a USB cable Plug the USB cable into the USB port device on the rear of the
4. Over The order contents are shown In Event mode the order contents are not shown and printing starts directly 5 Verify the order contents and enter the password For details on this operation see Verifying Order Contents and Entering a Password on page 37 Using Split Image Print This function lets you print several images on a single sheet Splitting into prescribed size images such as passport photos is also possible This function is available in Full mode and Event mode 1 Touch any place on the screen Touch screen to start gt ME E MORY STICK PRO m m xD Picture Card E Standard DUO SD Card CompactFlash MultiMediaCard The language selection screen appears When using Event mode and when only one language was selected at the administration screen the language selection screen does not appear Instead the Main Menu appears In this case proceed to step 3 2 Touch the language you want to use Please select language REWER English Espa ol Deutsch Start Over Precautions about using the unit are shown Read these carefully and then touch the OK button When a Bluetooth USB adaptor is inserted and Bluetooth communication 1s enabled the device selection screen appears Touch Memory Card Insert the memory card into the respective slot on the front side of the unit When the memory card is recognized the Main Menu appears Touch Split Ima
5. R pet Za c A f WO Ha N 6 i S 4 Adjust the width of the paper holder When using the print pack 2UPC C14 Attach adaptors to both ends of the paper holder Make sure the color of the label on the upper part of the adaptors matches the color of the label on the paper holder Insert the adaptors firmly and completely into the paper holder When using the print pack 2UPC C13 or 2UPC C15 Remove the adaptors from the paper holder Store the adaptors in a safe place so as not to lose them Loading the paper roll and ribbon cartridge When using the printer for the first time you must first load a paper roll and ribbon cartridge When using the 2UPC C14 adaptors must be installed in the paper holder as described in the section Attaching adaptors to paper holder on page 12 For information on how to remove a spent paper roll and ribbon cartridge see the section Removing the paper roll and ribbon cartridge on page 16 e Always use a designated print pack Always replace the paper roll and ribbon cartridge together as a set Loading the paper roll Insert the paper core into the paper roll Installation suoneledeld gsajdeyD 13 suoleledolgd z 129 dEUD If the edges of the paper roll are uneven make sure to even them out before installing the paper roll Otherwise a malfunction may occur f the paper is wound loosely a
6. Setting Items dnies guejdeu2 29 uonejedo p Je1deu 30 Operation Outline Print Types The unit can print photos taken with a digital camera in several different ways as listed below Print Select desired images from the contents of the memory card specify the number of copies and print This function is available in all operation modes Index Print All images on the memory card are printed as thumbnails This 1s convenient to check memory card contents and visually sort through a large number of images when selecting images for printing This function is available in Full mode and Event mode Split Image This lets you print several images on a single sheet Splitting into prescribed size images such as for passport photos 1s also possible This function is available in Full mode and Event mode Border Print You can select from a variety of border designs to be printed around the image This function is available in Full mode and Event mode Print All Images This lets you print all images on the memory card in one go There is no need to select images This function is available in Quick Print mode Operation Outline Operation Flow Full mode Event mode Quick Print mode Touch the screen Touch the screen Select language Select language Select input method 2 Select input method 2 Insert memory card or send images 2 Insert memory card or send images 2 Select print type Sel
7. button Perform red eye reduction on one eye at a time With some images the compensation function may not be entirely successful 5 Touch the OK button The original screen reappears Also when red eye reduction was carried out the results will not be reflected on the preview screen However the symbol under the preview image indicates that the function was used Adding the Date You can add the date when an image was shot to the printout This function is available when Print or Border Print was selected from the Main Menu For this function to work the image data must conform to the Exif 2 0 or later specification 1 On the list display of images touch the Add Date button The date 1s added to all images that are printed To cancel the setting touch the Add Date button once more The format in which the date information is printed can be changed at the administration screen For details see the section Print Tab on page 26 Printing From DPOF Settings If a digital camera that supports DPOF was used the images to print and the quantity for each image can also be specified at the camera When image and quantity selection was made at the camera and such a memory card is then inserted into the slot of this unit the selection data generated by the digital camera are automatically read by the unit By using these data printing can be carried out quickly and easily If the number of imag
8. koali 20 SUSU os a RZ AE sodes eR cuidado RADE 20 DEDUCI T ereer O Z A a Ani 21 Checking the Ribbon Cartridge Remainder 21 Chapter 3 Setup Set b ProCedulte iai ibat dep GG a 22 sI ddapgu gccee meet 23 SAISIR E RM Ds tee ems RE C ORC RE 23 SCIEE S TAB edaac did 24 Template Tad weak odu hola z KE a a ec 25 Text IUGS e iea gi ORC aA 29 Pnt TAD C 26 PLMEOIOE p NP RR E 26 PICO PAD a z E E A t RUM e Eau O 21 Adminis tanon TaD RARE olea cedo needed ZE 28 Table of Contents Chapter 4 Operation Operation OUTING Gda diod i aa A GE aiw dci 30 Pra TY DOS rm c c 30 CODErabo BE OPR znad ao nid O pi 31 Setting Memory CAES iiesccy zlec iii awiza nca Loc rasa Poor adas 32 Usmo MeBOLV DUCK das ARON AE AES dA 22 Using a CompaciFlash arduus Etna Leika 32 Usine a SmartMedia Card uses Ung eui A 33 Using a SD Card MultiMediaCard sees 33 Usine a xDsPIetute C IE sara A EEEE odc 34 Using Bluetooth communication eeeeeeeeeeeeeeeeeeeenn nnne 34 Selecting Images for Printing 34 Verifying Order Contents and Entering a Password 37 Using Index PII iuc eoo ido eee nara dad eski zob seite 38 Using Split Image Print se 39 USING BORGER PRUNE uz owadicc wicca S 41 Printing All Ima
9. screen and saving the file on a memory card you can insert the memory card into the unit to enter a Print Size password instead of using the on screen numeric Quantity keypad For details see Entering Passwords Using Memory Cards Remote Password Input on page 52 Order No Price Printable Sheet Quantity Estimated Print Time Eg Back The numeric keypad appears in the right part of the screen If password or budget code input was disabled at the administration screen printing starts immediately when the Print Start button is touched uonejedo p J8 1dEUD 2 Enter the password and touch the OK button Use the numeric keypad on the screen to enter the 4 digit password This can be either the checkout password or the administrator password If budget code input was selected at the administration screen enter the budget code instead of the password and then touch the OK button Please input password then press OK Order No Print Size Quantity Price Printable Sheet Quantity Estimated Print Time The printing process starts When all necessary data have been read from the memory card a message about removing the memory card appears Remove the memory card from the memory card slot Selecting Images for Printing 37 uonejedo p 18 1dEUD 38 Using Index Print This function prints out all images on a memory card in reduced size to provide an ind
10. was selected at the administration screen the language selection screen does not appear Instead the Main Menu appears In this case proceed to step 3 2 Touch the language you want to use Please select language in Over i Precautions about using the unit are shown Read these carefully and then touch the OK button When a Bluetooth USB adaptor is inserted and Bluetooth communication is enabled the device selection screen appears Touch Memory Card The following buttons are available in the screens that follow Touch the buttons when required e Start Over Returns to the start screen in step 1 e Main Menu Returns to the Main Menu screen in step 4 Help Displays the help screen for a description about procedures that apply to the current screen 3 Insert the memory card into the respective slot on the front side of the unit When the memory card is recognized the Main Menu appears 4 Touch Print Touch a button to select menu Split Image Border Print Print Size A list display of images contained on the memory card appears D Touch the images that you want to print Print Quantity Select Alt Print Size Total Quantity Price To deselect an image touch the image once more To select all images touch the Select All button If there are more images than fit on one list display screen the 4 and P buttons can be used to move
11. 15 of FCC Rules If you have any questions about this product you may call Sony Customer Information Service Center 1 800 222 7669 or http www sony com Declaration of Conformity Trade Name SONY Model UP CR10L Responsible Party Sony Electronics Inc Address 16530 Via Esprillo San Diego CA 92127 U S A Telephone Number 858 942 2230 This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation For the customers in Canada This Class B digital apparatus complies with Canadian ICES 003 Warning on power connection Use a proper power cord for your local power supply Use the approved Power Cord 3 core mains lead Appliance Connector Plug with earthing contacts that conforms to the safety regulations of each country if applicable 2 Use the Power Cord 3 core mains lead Appliance Connector Plug conforming to the proper ratings Voltage Ampere If you have questions on the use of the above Power Cord Appliance Connector Plug please consult a qualified service personnel For the customers in Europe The manufacturer of this product is Sony Corporation 1 7 Konan Minato ku Tokyo Japan The Authorized Representative for EMC and product safety is Sony Deutschland GmbH Hedelfinger Strass
12. Memory Stick Memory Stick Duo Memory Stick PRO and Memory Stick PRO Duo are trademarks of Sony Corporation CompactFlash is a trademark of SanDisk Corporation registered in the United States and other countries SmartMedia is a registered trademark of Toshiba Corporation MultiMediaCard is a trademark of Infineon Technologies AG e Microdrive is a registered trademark of Hitachi Global Storage Technologies miniSD is a trademark of SD Card Association Adobe and Photoshop are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and or other countries xD Picture Card is a trademark of Fuji Photo Film Co Ltd The Bluetooth word mark and logos are owned by the Bluetooth SIG Inc and any use of such marks by Sony Corporation is under license Other product names are the registered trademarks or trademarks of their respective manufacturers Information Updates For the latest information please visit the UP CRIOL support page at http www sony net snaplab Supplied Documentation Information Updates 7 8uiino Jejdeu suolieledolgd z 19 dEUD Preparations Chapter Note found on the manufacturer label located at the rear of the unit These differences are described in this document The location and design of the unit s power control and the whenever they arise supplied accessories differ depending on the serial number Suppl
13. Preparing an Expansion CompactFlash Card on page 19 Templates are created using the Adobe Photoshop plug in that is contained on the supplied CD ROM For details see the documentation of the Adobe Photoshop plug in Templates Copy All Copies all template data stored on a memory card inserted front side memory card slot to the expansion CompactFlash card Touch the button and then follow the instructions that appear If an error message appears check the following likely causes The expansion CompactFlash card has insufficient free space The file selected for copying is not in the specified folder or does not meet the promotional image specifications If there are templates with the same name stored on the expansion CompactFlash card they will be overwritten Be careful when performing this procedure because even read only files will be forcibly overwritten Delete All Deletes all template data stored on the expansion CompactFlash card Be careful when performing this procedure because even if the existing templates are read only files they will be forcibly deleted Text Input You can enter text for addition to images When Print or Border Print is performed the entered text is printed along with the image Alphanumeric characters and symbols can be used to create text To enter text touch the Text Setting button to bring up the text input screen For information on how to use this screen see
14. Quick Print mode before printing can begin Budget code Determines whether a budget code must be input when printing When this is set to ON the unit requests input of a budget code before printing in Full mode and Quick Print mode The entered code is output in the print logs For example you could assign different budget codes to different departments allowing you to manage actual print counts per department A budget code is a number up to 4 digit Administrator Password Allows you to set the password for the administration screen Touch the button Using the numeric keypad that appears specify a password a 4 digit number Then touch the OK button The administrator password can also be used as the password that must be entered for printing to start Checkout Password Allows you to set the password to be input when starting to print Touch the button Using the numeric keypad that appears specify a password a 4 digit number Then touch the OK button When the OK button is touched while an expansion CompactFlash card is inserted a password file is created on the expansion CompactFlash card The password file 1s used when using memory cards to enter passwords For details see Entering Passwords Using Memory Cards Remote Password Input on page 52 Print Logs Displays the print history of the unit with one entry for each order Order No Budget Code Print Size Print Type Quantity 0001 0001 5x
15. SD Card or MultiMediaCard insert the memory card directly into the corresponding slot Do not insert a SmartMedia card or other memory cards into the CompactFlash type adapter Doing so could cause the image data stored in the card to be deleted or damaged Always make sure that the memory card is oriented correctly before inserting it in the appropriate slot of the unit Inserting any memory card in the wrong direction may damage the unit and or memory card and cause malfunctions Do not remove the memory card or turn off this unit while data is being read or written to the memory card Doing so could cause the data that is being recorded to be deleted or damaged Supported Memory Cards and File Formats xipueddy 57 xipueddy 58 Cleaning Cleaning the Inside of the Printer If stripes scratches or other marks begin to appear on prints cleaning the inside of the printer may solve the problem Cleaning the inside of the printer is especially effective in removing white stripes and scratches like those shown in the figure White stripe Threadlike scratch White stripes tend to appear when using the 2UPC C13 or 2UPC C15 printing pack after printing a large quantity of prints with a 2UPC C14 printing pack Also if foreign particles become affixed to the thermal head white stripes or scratches may begin to appear When this happens use the cleaning cartridge supplied with the printer and the cleaning
16. among screens Touching the Add Date button on this screen will cause the shooting date to be printed on each photo For details see the section Adding the Date on page 49 mages in a format not supported by the unit and images that are broken corrupted file data are indicated by the following icon mages where one side vertical or horizontal is less than 480 pixels are shown as small thumbnails Because of their lower resolution such images may not print at high quality Depending on the memory card type or the number of images stored on the memory card the loading speed may drop significantly or the images may not load properly uonejedo p e1deu5 Specify the number of copies quantity to print Use the and buttons to specify the quantity Print Quantity Print Size Total Quantity Price The quantity specified for an image is shown at the top right corner of the thumbnail To specify the individual quantities touch the thumbnail of the image with the quantity you want to change and then touch the or button If the Select All button has been selected the quantity set with the and buttons will apply to all images Selecting Images for Printing 35 If the digital camera with which the photos were taken supports DPOF the images to print and the quantity for each image can already be specified at the camera For details see the section Printing
17. following screen appears Touch screen to start I MEMORY STICK PRO P i xD Picture Card Standar Ld ard DUO SD Card CompactFlash MultiMediaCard For details on subsequent steps see the section Operation on page 30 Shutdown 1 Complete any pending operations and then bring up the following screen Touch screen to start E emo RY STICK PRO al P re Car xD Picture Card 4 Standard DUO SmartMedia CompactFlash 2 Shut down the unit as follows For units with serial numbers starting with 11 Verify that no memory card is inserted in any of the front side memory card slots of the unit Then press the on standby button For units with serial numbers starting with 51 Verify that no memory card is inserted in any of the front side memory card slots of the unit Then turn off the POWER switch Checking the Ribbon Cartridge Remainder You can check the remainder of the ribbon cartridge 1 At the Start Guide display touch the top right corner of the screen twice in succession Touch screen to start The remainder of the ribbon cartridge is displayed 100 The original screen reappears after 5 seconds Startup and Shutdown 21 suonejedeJjd Z Jejdeu2 dnies e Jejdeu5 22 Setup Setup Procedure Before the unit can be used you must first make various settings This includes selecting the language and currency selecting the service mode a
18. function The touch panel adjustment can also be performed from this tab T Screens tab Lets you select the operation mode and the promotional images function L1 Template tab Lets you load and delete templates and enter text to be added to images Print tab Lets you select the order numbering format and the date format The print position adjustment can also be performed from this tab e Print color tab Lets you adjust the print quality Pricing tab Lets you set the currency to use and the price of prints 77 Administration tab Lets you limit the number of prints per order and make password settings The print logs and system logs can also by displayed from this tab When the setting is complete touch the button Setting Items System Tab Pm lola lela Touch Panel Print Head Adjustment Cleaning dnies e jejdeu5 Beep Determines whether a beep sound is heard when performing an operation step or when an error has occurred PC Connection Determines whether the unit can be controlled from a computer When set to OFF the unit cannot be controlled from a computer even if connected via a USB cable Language Selects the language to be used for operation screens and messages Up to four languages can be selected When multiple languages are selected the user can select the language when placing an order The administration screen uses the language selected as
19. image adjustment is complete touch the OK button The original screen reappears Printing in Sepia or Black and White You can set the image color to sepia or black and white for printing 1 On the Edit Menu touch Sepia B amp W The following screen appears j nip HH CHE ul IE 2 Touch either Sepia or B amp W To cancel the setting touch the same button once more 3 Touch the OK button The original screen reappears Image Editing uonejedo p e1deu5 47 uoqel1odO p 18 1dBUD 48 Compensating for the Red Eye Effect On photos taken with a flash the so called red eye effect can sometimes be a problem This function makes the effect less noticeable If cropping or rotation is performed after red eye reduction the corrections for red eye are canceled Make sure to perform red eye reduction after cropping or rotation 1 On the Edit Menu touch Red Eye Reduction The following screen appears The compensation frame is located in the center of the image 2 Use the arrow buttons to move the compensation frame to the eye position Use the and EM buttons to adjust the size of the compensation frame so that the eye is fully within the frame Image Editing 4 Touch the button The compensation function is carried out The result is shown in the small image at the bottom of the screen To cancel the compensation function touch the
20. just a touch of the screen Also by incorporating a paper roll and ribbon cartridge system replacement of the paper and ribbon is a snap What This Product Can Do Chapter Customizable with original data By inserting a memory card expansion CompactFlash card carrying promotional images and border data into the expansion slot screen savers can be displayed and photos can be combined with borders for printing Original images can be used for the screen saver and border data Printing with Bluetooth wireless technology Using an optional Bluetooth USB adaptor you can send images from Bluetooth compatible devices such as mobile phones and print wirelessly The versatile print services available when printing from a memory card are also available when sending images via Bluetooth communication An expansion CompactFlash card is necessary to use this function 2 Compact integrated body The display and printer are housed in a single enclosure which does not take up much space and easily fits on a shop counter or similar In addition the screen angle can be adjusted to eight different settings to fit operation conditions 1 A commercially available CompactFlash card or Microdrive is required 2 For more on compatible Bluetooth USB adaptors see Optional accessories on page 62 of Specifications The adaptor may not be commercially available depending on your country or region Consult your local Sony dealer
21. of each order If you print multiple copies of the first image the order number is printed on each copy The order number is printed as a watermark on the edge of the photo Date Print Format Specifies the format that is used when including the date in the printout e YYYYMMDD Example 2005 10 30 e DDMMYYYY Example 30 10 2005 MonthDDY Y Example Oct 30 05 MMDDYYYY Example 10 30 2005 Setting Items Print position adjustment If the print is not properly centered on the paper you can adjust the position in the X and Y direction The adjustment range is 2 mm in each direction ry Decrease the Y value X m Increase Y ry Decrease the X value the X value Increase the Y value F1 Y The direction the prints are ejected Print Color Tab Printer Color Setting 4 gt d gt m gt m Various settings related to print color and quality can be made here Each item is set with the 4 and P buttons The setting range is 16 in steps of 2 Red Green Blue Adjusts the color component of the respective color Dark Light Adjusts gradation in dark and light sections Gamma Adjusts the halftone density aj de Adjusts the outline sharpness of the image abbreviation PuB Russian Ruble SEK Swedish Krona Pricing Tab EADIE e MI Price Indication Currency ON Pricing Additional Price Index Print Border Print dnies e saydeyo Ve
22. paper on the paper roll When the ribbon cartridge 1s finished remove the remainder of the paper roll and install a new ribbon cartridge and paper roll Make sure to use a matching paper roll and ribbon cartridge set Using an unmatched combination will not only prevent you from obtaining normal print results but may cause a paper jam or a malfunction Do not touch the printing surface of the paper roll or the ink on the ribbon cartridge Fingerprints and other pollutants can lead to reduced print quality Removing the paper roll and ribbon cartridge Removing the paper roll 1 Open the front door 2 Pressthe paper holder release button and pull the paper holder out RR RE U A 3 Remove any paper remnants from the paper holder Removing the ribbon cartridge 4 Press the latch on top of the paper holder and open the 1 Open the side door holder suonejedejd z Je1deu 5 2 Pull back the latch on the ribbon cartridge to release the lock and then grasp the ribbon cartridge and remove it If the ink ribbon breaks you can reconnect it with a piece of tape and use the remaining ribbon Immediately after printing the thermal head inside the unit will be hot When removing a cartridge do not insert your hand into the ribbon cartridge access opening to prevent t
23. power cord f you do not intend to use the unit for a long time disconnect the power cord Unplug the power cord by grasping the plug not the cord itself Do not disassemble the unit There is a danger of electric shock from the internal parts Be careful not to spill water or other liquids on the unit or to allow combustible or metallic material to enter the cabinet If used with foreign matter in the cabinet the unit is liable to fail or present a risk of fire or electric shock If the unit malfunctions or if a foreign body falls into the cabinet disconnect the power immediately and consult your Sony service facility or your Sony dealer To store a half used printing pack replace it in its original packing and reseal the package If possible keep the sealed printing pack in a cool dark location To subsequently use the printing pack place it in its sealed package in a warm room for several hours Doing so prevents condensation from forming when the printing pack is removed from its package Installation nstall the unit on a level surface Do not install the unit on a slant or on its side Doing so could damage the unit Do not jar or drop the unit Precautions Do not install the unit in any location that 1s subject to instability excessive dust extremely high or low temperatures vibration high humidity direct sunlight Do not block the ventilation holes on the unit Doing so
24. received images appears on the unit s screen If your Bluetooth compatible device requests a pass code entry enter OOOO 1 The pass code may also be referred to by another name such as passkey or PIN code You cannot change the pass code from the printer D When the transfer is finished touch the OK button When transferring multiple images transfer all of the images before touching the OK button The Main Menu appears Touch a button to select menu Split Image Border Print Print Size The procedure following the Main Menu is the same as when memory cards are used See details on print procedures starting on page 34 Printing With Bluetooth Communication uonejedo p e1deu5 51 uonejedo p l8 1dEUD 52 Entering Passwords Using Memory Cards Remote Password Input You can enter a password without using the on screen numeric keypad by simply inserting a memory card First save the password file created in the unit s administration screen onto a memory card When password entry is requested insert the memory card into a card reader connected to the USB port and the password recorded on the file will be read automatically You can also insert the memory card or USB flash memory device containing the password file directly into the unit s memory card slots or USB port host 1 Compatibility with some card readers and USB flash memory devices is not guaranteed Pro
25. sheet supplied with the printing pack to clean the inside of the printer The cleaning cartridge can be used repeatedly 1 Bring up the administration screen on the UP CRIOL and select the System tab 2 Open the side door and remove the ribbon cartridge 3 Insert the cleaning cartridge all the way into the printer 4 On the System tab touch the button About 30 cm of print paper emerges and a message asking for confirmation to begin cleaning appears on the screen Cleaning Remove the paper from the back side of the cleaning sheet the side without an illustration Be careful not to confuse the back and front sides of the cleaning sheet Determine by the width of the print paper the orientation to affix the cleaning sheet and affix the cleaning sheet evenly and squarely onto the ejected paper as illustrated When using the 2UPC C14 printing pack orient the cleaning sheet lengthwise rather than crosswise Firmly affix the entire cleaning sheet so that the corners do not peel up and the center is not raised If the corners of the cleaning sheet peel up cleaning may not be performed properly Remove the paper from the front side of the cleaning sheet 8 The adhesive surface of the cleaning sheet is exposed now so check again to make sure that none of the corners have peeled up and the center has not been raised 2UPC C14 2UPC C13 C15 Q Touch the OK button in the confirmation message Cleaning begin
26. strike the surface of the display with a hard object When the filter for the cooling fan becomes dirty When the filter for the thermal head cooling fan has become considerably dirty remove it and rinse off the dirt with water Do not scrub the filter mesh with a brush or other cleaning tool Cleaning When the printer roller becomes dirty When the printer roller becomes dirty use a soft cloth moistened with cleaning alcohol to gently wipe the roller while turning it When cleaning the printer roller always set the printer to standby mode with the on standby button or turn it off with the POWER switch then disconnect the power cord Troubleshooting Before sending the unit out for servicing check the items listed below If you still cannot solve the problem contact your Sony Authorized Dealer Cannot load paper roll Are you trying to load 2UPC C13 C15 while adaptors are mounted in the paper holder Remove the adaptors and then load the paper roll page 12 Paper roll was loaded but no paper message appears Paper roll may not have been loaded correctly Ensure that paper roll is loaded correctly page 13 Ribbon cartridge was loaded but no ribbon cartridge message appears Ribbon may not have been loaded correctly Ensure that ribbon is loaded correctly page 15 Out of paper message appears but there is still paper in the unit This is not a defect Some
27. system Do not insert the Memory Stick into a CompactFlash type adapter as this may accidentally delete the data on the Memory Stick Supported Memory Cards and File Formats xipueddy 59 xipueddy o6 Do not remove the Memory Stick while reading or writing data Data may be corrupted in the following cases When the Memory Stick is removed or the system is turned off during read or write operation When the Memory Stick 1s used in locations subject to static electricity or electrical noise Do not strike bend or drop the Memory Stick Do not attempt to disassemble or modify the Memory Stick Do not get the Memory Stick wet Avoid storing or using the Memory Stick under the following conditions n a hot location such as inside a car or outside on a very hot day n direct sunlight n a humid location or where corrosion occurs easily Do not touch the Memory Stick contacts with anything including your finger and metallic objects Do not affix anything other than the supplied label to the Memory Stick labeling position Affix the supplied label so that it does not stick out beyond the labeling position Carry and store the Memory Stick in its case Notes on using Memory Stick Duo Usea sharp object such as a ballpoint pen to move the Memory Stick Duo write protect switch e Some Memory Stick Duo are not equipped with a write prote
28. the image list screen will appear after the Main Menu with the number of images corresponding to the maximum number being selected You can then proceed to print these images or change the image selection Image Editing The Edit Menu gives access to the following functions Crop amp Rotate page 46 Color Adjustment page 47 e Sepia Black amp White printing page 47 Red Eye Reduction page 48 The steps for image editing are described below 1 Touch the Edit button The Edit Menu appears 2 Touch the item you want to edit Touch a button to select menu um S Crop amp Rotate Red Eye Reduction T Sepia B amp W The respective editing screen appears For details on operation steps see the later sections Filc Color Adjustment 3 When finished editing touch the OK button on the respective editing screen The original screen reappears An edited image is indicated by a pencil symbol in the list display To remove editing effects You can return a temporarily edited image to its original unedited state 1 Select an edited image on the image list screen and touch the Edit button The Edit Menu appears 2 Touch the Reset button A confirmation message appears Touch the Yes button The editing effects for the selected image are removed and the Edit Menu reappears Image Editing uoneJedo p 191dEeU9 45 uoqeledO p le8 1deU 46 Specifying the L
29. the section Text Input Screen below To use the entered text select ON dnies e 1 dey9 Text Input Screen Steve and Janet s Wedding June 14 2007 p Size Position Color Emm LIM EB EFTE Cancel 4 Input tab Touch the keys shown on the screen to enter text Up to 2 lines containing a total of 128 alphanumeric characters can be entered To make a correction touch the BS Backspace button If you keep touching the button the entire line where the cursor is located will be erased Font tab Lets you select the font to be used Size tab Use the and buttons to control the text size The size setting range is 8 72 points in 2 point steps Setting Items 25 dnies e lejdey9 26 Position tab Lets you specify where in the image the text should be placed Color tab Lets you specify the text color Depending on the number of characters and text size selected it may not be possible to print the entire text in some cases Print Tab SJ REJ c SNL JE 71 Order Numbering Print Position Adjustment Date Print Format YYYYMMDD DDMMYYYY MonthDDYY MMDDYYYY FT a aT PT TTT Order Numbering Select one of the following settings related to including the order number on the prints e OFF No order number is printed Print all The order number 1s printed on all photos Print first only The order number is printed on the first image
30. 1 1 Touch one of the buttons 1 4 A list of languages appears 2 Touch the language you want to use and touch the OK button To cancel a setting touch Off When only one language was selected the language selection screen does not appear when placing an order Setting Items 23 dnies e lajdey9 24 Touch Panel Adjustment This allows you to calibrate the touch panel Touch the button and then touch the box that appears on the screen When you touch the box a new box appears in a different location Touch each of the boxes in order When no more boxes appear the touch panel adjustment is complete Print Head Cleaning This allows you to clean the inside of the printer For details see the section Cleaning the Inside of the Printer on page 56 Screens Tab CJ m I MENKCKCCZJF 71 Mode Selection Quick Full Event Print Mode Mode Promotional Images Mode Selection You can select either Quick Print mode Full mode or Event mode Quick Print This mode limits the number of options that are available to the customer It 1s best suited to allow easy and quick printing of photos The customer can select whether to print only selected images from the memory card or all images on the memory card Image editing 1s not possible You can require the input of a password before printing is carried out e Full Mode In this mode the customer can access the full range of functions pr
31. 2 666 583 16 1 Digital Photo Printer Operating Instructions Before operating the unit please read this manual thoroughly and retain it for future reference znapLab UP CR10L EMORY STICK m 2005 Sony Corporation 2 Owner s Record The model and serial numbers are located at the rear Record these number in the space provided below Refer to these numbers whenever you call upon your Sony dealer regarding this product Model No Serial No To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture To avoid electrical shock do not open the cabinet Refer servicing to qualified personnel only THIS APPARATUS MUST BE EARTHED Note The location and design of the unit s power control and the supplied accessories differ depending on the serial number found on the manufacturer label located at the rear of the unit These differences are described in this document whenever they arise For units with serial numbers starting with 51 only To disconnect the main power unplug the AC IN connector For units with serial numbers starting with 11 only This unit has no power switch When installing the unit incorporate a readily accessible disconnect device in the fixed wiring or connect the power plug to an easily accessible socket outlet near the unit If a fault should occur during operation of the unit operate the disconnect device to switc
32. 7 P 0002 0002 5x7 P 0003 0003 5x7 l 0004 0004 5x7 l 4 4 0005 0005 5x7 S 5 5 0006 0006 5x7 S 6 6 B B A A 1 1 2 2 3 3 0007 0007 5x7 1 1 0008 0008 5x7 8 8 0009 0009 5x7 9 9 0010 0010 5x7 10 10 Page Each entry comprises the following items Order Number Budget Code Print Size Print Type P Print I Index Print S Split Image Print B Border Print A Print All e Quantity Price The print log information can be exported to the expansion CompactFlash card To do this touch the button The print log data are exported in CSV format The exported CSV file also contains the budget code To clear the print log data touch the button System Logs Displays the operation history of the system Print counter Cumulative print quantity Thermal head print quantity Hours of operation Power on 12 34 56 Fan 1 23 45 LCD back light 12 34 56 Firmware ver 1 00 DE The following items are shown Print counter Cumulative print quantity e Thermal head print quantity Hours of operation power on time fan operation time LCD backlight operation time Firmware version The system log information can be exported to the expansion CompactFlash card To do this touch the F button The system log data are exported in CSV format To reset the print counter touch the button Reset to Factory Settings Returns the unit to the factory default settings
33. Card Printing All Images on a Memory Card This function lets you print all images stored on a memory card in one operation producing one print per image The function is available in Quick Print mode 1 Touch any place on the screen Touch screen to start re CompactFlash The language selection screen appears When only one language was selected at the administration screen the language selection screen does not appear Instead the Main Menu appears In this case proceed to step 3 MEMORY STICK PRO xD Picture Card IA Standard DUO 2 Touch the language you want to use Please select language English Francais Espanol Deutsch Start Over Precautions about using the unit are shown Read these carefully and then touch the OK button When a Bluetooth USB adaptor is inserted and Bluetooth communication is enabled the device selection screen appears Touch Memory Card 3 Insert the memory card into the respective slot on the front side of the unit When the memory card is recognized the Main Menu appears A Touch Print All Images Touch a button to select menu Start Over The order contents are shown 5 Verify the order contents and enter the password For details on this operation see Verifying Order Contents and Entering a Password on page 37 If the number of images on the memory card is higher than the maximum allowable number of prints per order
34. From DPOF Settings on page 49 If you wish to print without editing the images proceed to step 9 To perform editing proceed to step 7 In Quick Print mode image editing is not possible Print Size Total Quantity Price uoqeledO p le8 1deU The preview screen appears 8 To edit an image touch the Edit button Print Size Total Quantity Price The edit menu appears This menu gives access to the Crop amp Rotate Color Adjustment Red Eye Reduction and Sepia Black amp White functions 36 Selecting Images for Printing Touch a button to select menu C O Crop amp Rotate Red Eye Reduction Fic a Color Adjustment Sepia B amp W For details on editing see the section Image Editing on page 45 9 Touch the Print button Print Size Total Quantity Price The order contents are shown In Event mode the order contents are not shown and printing starts directly Verifying Order Contents and Note Entering a Password Do not remove the memory card before this message is shown Otherwise data on the memory card may be erased or corrupted Removing and inserting an expansion CompactFlash card during printing may also cause improper printout 1 Verify that the print quantity pricing and other items are correct Then touch the Print Start button Confirm your order then press Print Start Memo By creating a password file in the unit s administration
35. SEMENT ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT EITHER DURING THEWARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY OR FOR ANY OTHER REASON WHATSOEVER The LCD panel fitted to this unit is manufactured with high precision technology giving a functioning pixel ratio of at least 99 99 Thus a very small proportion of pixels may be stuck either always off black always on red green or blue or flashing In addition over a long period of use because of the physical characteristics of the liquid crystal display such stuck pixels may appear spontaneously These problems are not a malfunction Specifications xipueddy 63 http www sony net Sony Corporation
36. ayout Crop 8 Rotate This function allows you to trim the image or rotate it thereby changing the composition of the image To crop the image You can perform cropping by zooming the image in and out and by shifting the position of the zoomed portion 1 On the Edit Menu touch Crop amp Rotate The following screen appears 2 Use the and EM buttons to adjust the size of the image 3 Use the arrow buttons to adjust the position of the image 4 Repeat steps 2 and 3 to obtain the correct printing image D When the composition of the image is as desired touch the OK button The original screen reappears Image Editing To rotate the image You can rotate the image in steps of 90 degrees 1 On the Edit Menu touch Crop amp Rotate The following screen appears 2 Touch the button Each time you touch the button the image is rotated by 90 degrees in the clockwise direction When the orientation of the image is as desired touch the OK button The original screen reappears Adjusting the Image Quality The following items can be adjusted Brightness e Tint e Saturation e Sharpness 1 On the Edit Menu touch Color Adjustment The following screen appears MENEREN eee 2 Use the 4 and P buttons to adjust the setting of the respective items Each item can be adjusted in 8 steps To cancel the adjustment touch the Cancel button When the
37. card Notes on using memory cards The following apply to all memory cards except Memory Stick For details about Memory Stick types on page 55 Before using any memory card be sure to carefully read its user manual When you purchase a memory card you must first initialize it with a digital camera If you initialize the memory card with a personal computer or any device other than a digital camera this unit may not be able to read the image data stored on the memory card Do not attempt to use any memory card that is not specified for use with this unit Doing so could damage this unit Do not strike bend or drop the memory card Do not attempt to disassemble or modify the memory card Do not get the memory card wet Because the memory card is vulnerable to humidity we recommend that such memory card not be used under humid conditions Avoid storing or using memory card under the following conditions n a hot location such as inside a car or outside on a very hot day n direct sunlight n a humid location or where corrosion occurs easily n a location where the memory card could be exposed to electrostatic discharge or electronic noise e Do not touch the contacts on a SmartMedia card CompactFlash card SD Card or MultiMediaCard with your hands or bare metal Always keep the memory card in its case when carrying or storing it e When using a SmartMedia card
38. could result in damage On transporting the printer Do not transport the printer with the supplied accessories ribbon cartridge and paper roll attached Doing so may cause a malfunction It is recommended that you store the ribbon cartridge and paper roll in the package they came in after you remove them On condensation If the printer is subjected to wide and sudden changes in temperature such as when it is moved from a cold room to a warm room or when it 1s left in a room with a heater that tends to produce quantities of moisture condensation may form inside the printer In such cases the printer will probably not work properly and may even develop a fault if you persist in using it If itis likely that condensation has formed set the printer to standby mode with the on standby button or turn it off with the POWER switch then leave the printer standing for about one hour If the printing pack is subjected to wide and sudden changes in temperature condensation may form on the ribbon cartridge or paper inside This will cause the printer to malfunction Also if the printing pack is used in this state spots are likely to appear on the printout Supported Memory Cards and File Formats Supported memory cards This unit supports the following types of memory cards e Memory Stick e Memory Stick PRO e Memory Stick Duo e SmartMedia card CompactFlash card e SD Card MultiMediaCard xD Picture Card S
39. ct switch When using a Memory Stick Duo without a write protect switch be careful not to edit or erase data by mistake Notes on using Memory Stick PRO This system does not support the access control security function SmartMedia card The parts of a SmartMedia card are shown below BEGIN uL E Contacts 9 Write protect area For details either visit the SSFDC forum Web site or refer to the user s manual accompanying your card http www ssfdc or p Index area Supported Memory Cards and File Formats Write protecting SmartMedia card data In order to protect important data from accidental erasure a SmartMedia card can be write protected to prevent data from being written To do so apply a write protect sticker at the location shown in the figure the write protect area C Write protect sticker Write protect area e When a sticker is applied in the write protect area the SmartMedia card cannot be used to store photographs taken with a digital camera To make it possible to write data to the card again simply remove the write protect sticker Do not attempt to reuse a sticker once you have peeled it off Doing so could damage the unit CompactFlash card The card can only be set in the slot in one direction If the card does not slide into the slot smoothly do not try to force 1t in Instead make sure that the card 1s oriented correctly with t
40. d opening Loading the ribbon cartridge 1 Open the side door fin 8 Return the paper holder into the unit Insert the paper holder until you hear a sharp click RK AI ge ee 3 NSA Installation suoneledeld z 12 dEUD 15 suoleledolgd z 19 dEUD 16 fit is difficult to insert the ribbon cartridge remove it and try inserting it again Reduce the ribbon slack by turning the cartridge spool in the direction of the arrow only if the ribbon cartridge cannot be inserted due to slack in the ribbon Do not rewind the ribbon cartridge for reuse in printing Printing will not be performed properly and it may cause a malfunction to occur Do not try to replace the ribbon cartridge while printing is in progress mmediately after printing the thermal head inside the unit will be hot When loading a cartridge do not insert your hand into the ribbon cartridge access opening to prevent the risk of burns 3 Close the side door Notes on storage Avoid placing where subject to high temperatures high humidity or dust direct sunlight After opening the bag use the ribbon cartridge and the paper as soon as possible When storing after partial use put the ribbon and the paper back in their bags Installation There is extra
41. e 61 70327 Stuttgart Germany For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents For kundene i Norge Dette utstyret kan kobles til et IT str mfordelingssystem For the customers in the U S A Lamp in this product contains mercury Disposal of these materials may be regulated due to environmental considerations For disposal or recycling information please contact your local authorities or the Electronic Industries Alliance www eiae org 3 4 Table of Contents Chapter 1 Outline What This Product Can Do cec seee see 6 Supplied Documentation 1 Lee eceeee ee eeee rennen 7 Information Upuales toya naan a 7 Chapter 2 Preparations Supplied Accessories aiz GO GEE E Oe nue Cosa e odes E ET ERE 8 Gontrols and FURCIUO S ua erectus queo die ee toii ne eee nein 9 FED iot dtd duet tut o mctu Dal dud ts 9 get A 10 I SIANAUON eel 11 Connecting the POWSEC Ord s restes Feb aeu RAPA EH 11 Adjusting the Display Ans le asia CEL Eda 11 Loading Paper Roll and Ribbon Cartridge ssss 12 Attachine the Paper Tray iudei p rre beet e esse delega Rp ka 18 Preparing an Expansion CompactFlash Card 19 Startup and ShutdOoWh iios ees saec eae ra vana sh va Run d Ew EU Xo ka
42. ect print type Border Print Split Image Print All Images Select border Select layout Select image number of copies oo mage number of copies Edit if required Verify order Verify order Enter password Enter password 1 Not required in Event mode 1 Not required depending on settings 2 When Bluetooth communication is enabled Operation Outline uoneJedo p 1e1deu5 31 uonejedo p 18 1dEUD 32 Setting Memory Cards A variety of memory cards listed below can be set in the drives and slots on the user interface panel to read image data stored on these memory cards e Memory Stick e CompactFlash cards e SmartMedia cards e SD Cards e MultiMediaCards e xD Picture Cards Be sure to back up all image data stored on memory cards before using it with this unit Multiple memory cards cannot be inserted and used at the same time To avoid loss of 1mage data or damage to the main unit never attempt to insert a Memory Stick SmartMedia card SD Card or MultiMediaCard into a CompactFlash type adapter set in the CompactFlash slot Using a Memory Stick Inserting the Memory Stick With the A mark on the Memory Stick facing up and forward completely insert the Memory Stick into the slot When you insert the Memory Stick into the unit it is automatically detected A Memory Stick Duo can also be used without an adapter As wit
43. eparing an Expansion CompactFlash Card For using the following functions an expansion CompactFlash card is required Border print Promotional images display e Text input e System logs and print logs export Printing with Bluetooth communication To create the expansion CompactFlash card a commercially available CompactFlash card is used The CompactFlash card can be a Type I Type II or Microdrive We recommend using a CompactFlash card with at least 512 MB of free space Creating the expansion CompactFlash card The supplied CD ROM contains sample templates for border prints and sample promotional images You can create an expansion CompactFlash card by copying this data onto a CompactFlash card with your computer If your computer cannot use CompactFlash cards you can copy the data to another type of memory card temporarily and then copy it to a CompactFlash card with the unit 1 Insert the CompactFlash card into the computer 2 Copy the promotional images Create the folder Sony UPCR in the root folder of the CompactFlash card and copy the entire folder Sony UPCR Promotion into it from the supplied CD ROM 3 Copy the border print templates The templates are stored in the folder Sony NUPCR Template on the supplied CD ROM The folder 1s divided into subfolders for each print size 3x5 4x6 and 5x7 Create the folder ASony UPCR Template in the root folder of the CompactFlash card and copy
44. eries Self Laminating Color Printing Pack Contains color ribbon cartridge and paper Ribbon cartridge for printing 2 rolls 4 x 6 inches print paper 2 rolls 2UPC C15 series Self Laminating Color Printing Pack Contains color ribbon cartridge and paper Ribbon cartridge for printing 2 rolls 5 x 7 inches print paper 2 rolls Printing capacity Each printing pack contains two sets of the ribbon cartridge and paper combination One set of the ribbon cartridge and paper allows you to print the following number of sheets Print pack 2UPC C13 2UPC C14 2UPC C15 Number of 300 sheets 200 sheets 172 sheets sheets Print size 89x 126 mm 101x152 mm 126 x 178 mm 2 mm 2 mm 2 mm 3 5 x 5inches 4x6inches 5x7 inches 3 32 inch 3 32 inch 3 32 inch However the number of sheets that can be printed may not be guaranteed if you replace the ribbon cartridge and paper before the ribbon cartridge and paper run out e Always use a designated print pack Troubleshooting Ribbon Cartridge and Paper xipueddy 61 xipueddy 62 Specifications Power requirements 100 to 240 V AC 50 60 Hz Input current 3 0 to 1 3 A max Operating temperature range 5 to 35 C Operating humidity range 20 to 80 no condensation External dimensions Approx 275 x 300 x 380 mm WHD 10 7 5 x 11 g x 14 74 inches excluding the maximum projecting parts Mass Approx 11 kg 24 Ib 4 oz printer only Printing method Dye s
45. es selected at the digital camera is higher than the maximum allowable number of prints per order the image list screen will appear with the number of images corresponding to the maximum number being selected You can then proceed to print these images or change the image selection This function is active when Print or Print All Images is selected at the Main Menu DPOF Digital Print Order Format is a standard that enables automatic printing of images taken with a digital camera Digital cameras supporting this standard write information about image selection and print quantity onto the memory card This information can then be used by DPOF compatible photo printers to enable quick and easy printing Available functions and operation steps for specifying DPOF information depend on the digital camera model For details refer to the documentation of your camera Adding the Date Printing From DPOF Settings uoneJedo p 1e1deu5 49 Printing With Bluetooth Communication Using an optional Bluetooth USB adaptor you can send images from Bluetooth compatible devices such as mobile phones and print wirelessly The print services available when printing from a memory card are also available when sending images via Bluetooth communication 1 For more on compatible Bluetooth USB adaptors see Optional accessories on page 62 of Specifications Preparing for Bluetooth communication Make sure of the fol
46. ex of the contents The maximum number of images printed on a single sheet is as follows e 3x5 30 images e 4x6 35 images e 5x7 56 images This function is available in Full mode and Event mode Exif images which exceed the maximum number of pixels to be handled 8 000 H x 6 000 V can also be index printed However the images are not supported and cannot be printed with functions other than index print and the following icon will appear with other functions 1 Touch any place on the screen Touch screen to start EX MEMORY STICK PRO LL Standard DUO p The language selection screen appears When using Event mode and when only one language was selected at the administration screen the language selection screen does not appear Instead the Main Menu appears In this case proceed to step 3 Using Index Print 2 Touch the language you want to use Please select language English Francais Espa ol Deutsch Start Over Precautions about using the unit are shown Read these carefully and then touch the OK button When a Bluetooth USB adaptor is inserted and Bluetooth communication is enabled the device selection screen appears Touch Memory Card 3 Insert the memory card into the respective slot on the front side of the unit When the memory card is recognized the Main Menu appears 4 Touch Index Print Touch a button to select menu Border Print Split Image Start
47. g the Inside of the Printeris 58 TFOUBDICSNOOUIING SE 61 Ribbon Cartridge and Paper sse 61 SDECIICONONS eR C E 62 Table of Contents 5 euilno Je deyo 6 Outline What This Product Can Do This device reads image data from memory cards used by devices such as digital cameras and prints out photos of superb quality It also prints out data sent from a computer The product has the following features Versatile print services Besides regular photo printout the unit can produce split image prints prints with borders and index prints It also allows the user to edit images before printing with functions such as trimming and color adjustment Order numbers can be printed as a watermark making print sorting easy Selectable operation modes To fit the environment where the unit 1s used Full mode Quick Print mode and Event mode can be selected Support for a wide range of memory cards All major memory card formats used in digital cameras are supported Memory Stick xD Picture Card SD Card MultiMediaCard CompactFlash card Microdrive and SmartMedia card High speed high quality printing Using a newly developed print engine that features a dyesublimation thermal transfer technology it is possible to print images of lasting beauty at high speed Easy operation by touch panel An 8 inch touch panel display is used allowing for easy operation with
48. ge Touch a button to select menu Border Print Print Size The split image layout selection screen appears Select the layout by touching it and then touch the OK button To print passport type photos select a suitable layout Frames that are marked with the same letter on screen will contain the same image The preview screen appears Using Split Image Print uoneJedo p 191dEeU9 39 uoqeledO p 13 deyo 40 6 Touch the frame you want to assign the image to Help ooo gt ggg Print Quantity Print Size Total Quantity Price Main Image l T Menu Selection Edit Print A list of images stored on the memory card is shown Select the image by touching it and then touch the OK button The preview screen appears again To assign multiple images repeat steps 6 and 7 for the desired number of images To change an image that you have already selected touch that image again and then touch the Image Selection button You can then select a new image Using Split Image Print 8 Specify the number of copies quantity to print Use the and buttons to specify the quantity Print Size Total Quantity Price Main Image i T i Menu Selection Edit Print If you wish to print without editing the images proceed to step 10 To perform editing proceed to step 9 To edit an image select it and then touch the Edit button Print Size Tota
49. ges on a Memory Card 44 im g Editing T 45 Specifying the Layout Crop amp Rotate eeeeeeeseeeeeeeeeeeee 46 Adj stne the Imas QUOD sind noie aea a O Iosue Dre edd 47 Printing in Sepia or Black and White suuue aaa aaa aaaaaaaznccczi 47 Compensating for the Red Eye Effect uuuua ooo aaa aaaaaaacccczi 48 Adding th Dat eR 49 Printing From DPOF Settings 49 Printing With Bluetooth Communication 50 Preparing for Bluetooth communication eeeeeeseeeeeeeeeeeee 50 Printing from Bluetooth compatible devices 50 Entering Passwords Using Memory Cards Remote Password Input 52 Creatine password TIES cu dou pet ble tando blat det DAR CLE dab cc 22 Entering passwords using memory cards suuee aaa aaaaaaaaa ace e aaa aae 22 Printing From a Computer cree esee eene 53 Installhine the Printer DU Ver zou pos AO APACZ W 53 Connection tO d COMPUT iien Echa ADU IA de 53 Appendix PTC CAUTIONS oc 54 Supported Memory Cards and File Formats 55 Notes on Using Memory Cards ccccccsecscseccccceeeeeseeseeeceeeeeeaaeeeeesees 55 CIS ANING me 58 Cleanin
50. h a Memory Stick insert it with the side that has the A mark facing upward Do not use a Memory Stick Duo adapter as this may cause a malfunction Setting Memory Cards Removing the Memory Stick When you see a message that prompts you to remove the Memory Stick first push the Memory Stick until you hear a click then pull it out Ut To prevent losing valuable data or damaging the Memory Stick never remove the Memory Stick from the slot until the message prompts you to remove it Using a CompactFlash Card Inserting the CompactFlash card With the A mark on the CompactFlash card facing up and forward completely insert the CompactFlash card into the slot When you insert the CompactFlash card into the unit it is automatically detected Before inserting the CompactFlash card make sure that it is oriented correctly Inserting the card in the wrong direction may damage the internal contacts which can lead to malfunctions Removing the CompactFlash card When you see a message that prompts you to remove the CompactFlash card pull the it straight out To prevent losing valuable data or damaging the CompactFlash card never remove the CompactFlash card from the slot until the message prompts you to remove it Using a SmartMedia Card Inserting the SmartMedia card With the terminals on the SmartMedia card facing up completely insert the card into the slot
51. h the power supply off or disconnect the power plug For the customers in the U S A This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna ncrease the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B of Part
52. he A mark pointing towards the slot A mark Direction of insertion For details refer to the user s manual accompanying your card SD Card The parts of an SD Card are shown below Write protect swith Contacts a For details either visit the SD Card Association Web site or refer to the user s guide accompanying your card http www sdcard org Write protecting SD Card data In order to protect important data from accidental erasure an SD Card can be write protected to prevent data from being written To do so slide the write protect switch as shown in the figure Write protect switch Write protected ti Not write protected When 1t is write protected the SD Card cannot be used to store photographs taken with a digital camera MultiMediaCard The card can only be set in the slot in one direction If the card does not slide into the slot smoothly do not try to force it in Instead make sure that the card 1s oriented correctly Always orient the card as show below Direction of insertion For details refer to the user s guide accompanying your card xD Picture Card The card can only be set in the slot in one direction If the card does not slide into the slot smoothly do not try to force it in Instead make sure that the card 1s oriented correctly with the A mark pointing towards the slot Direction of insertion For details refer to the user s manual accompanying your
53. he risk of burns You will need to reuse the paper core Be careful not to misplace it Installation 1 T suoleledolgd z 19 dEUD 18 3 Close the side door Attaching the Paper Tray Attach the supplied paper tray Installation When using the print pack 2UPC C14 or 2UPC C15 About 100 sheets of printouts can be left on this paper tray However the number of printouts which can be accumulated on the paper tray changes according to the environment condition where the printer is used or the printed image Remove the printed sheets accumulated on the paper tray as soon as possible When using the printing pack 2UPC C13 IRI Raise the eject paper stopper About 100 sheets of printouts can be left on this paper tray However the number of printouts which can be accumulated on the paper tray changes according to the environment condition where the printer is used or the printed image Remove the printed sheets accumulated on the paper tray as soon as possible Do not touch the printouts until they have been ejected from the printer If a printout gets stuck in the eject slot remove it from the slot immediately To remove the paper tray Grasp the bottom of the paper tray lift it up while keeping it horizontal and pull it out Pr
54. ied Accessories Make certain you have received the following accessories Paper Tray 1 Power Cord 1 Cleaning Cartridge 1 2 Adaptor right 1 EN S USB Cable with Ferrite Core 1 9 Before Using this Printer 1 Ferrite Core 1 4 Software License Agreement 1 CD ROM 1 Warranty Card 1 1 The paper holder is stored in the printer Be sure to remove the paper holder from the inside of the printer before turning the power on 2 For information on use see the section Cleaning the Inside of the Printer on page 58 3 For units with serial numbers starting with 11 only 4 For units with serial numbers starting with 51 only Notes Before transporting the unit remove the ribbon cartridge and paper roll from the unit When taking the unit out of the carton box be careful not Before transporting the unit also remove any paper to hurt your back remnants from the paper holder The paper remnants The packaging materials are needed when transporting may slip into the inner parts of the unit and result in the unit so we suggest you keep them damage if not removed 8 Supplied Accessories Controls and Functions Front iS Q Display Shows the operation screen Because the display is a touch screen the user simply touches the field for the desired operation The angle of the display can be adjusted for best viewing Q Access indicator Lights when a
55. k type The table below lists the image count for one ribbon cartridge and paper roll set Print pack 2UPC C13 2UPC C14 Number of 300 sheets 200 sheets 2UPC C15 172 sheets sheets Print size 89x 126mm 101x 152mm 126x 178 mm 2 mm 2 mm 2 mm 3 5 x 5inches 4x6inches 5x7 inches 3 32 inch 3 32 inch 3 32 inch Do not replace the ribbon cartridge and paper roll before they are used up Otherwise the above number of sheets may not be achieved Place the paper roll vertically If you place the paper roll horizontally the paper roll may roll around and fall This may cause an injury 0 l Hold the paper roll with both hands so that you do not drop it because it is heavy Dropping may result in an injury Hold the paper roll with both hands Installation An IC board is incorporated in the ribbon cartridge Do not touch the terminal of the IC board with anything including your fingers or metallic objects Also do not strike bend or drop the IC board Attaching adaptors to paper holder Paper roll widths vary according to the print pack When using the 2UPC C14 print pack attach an adaptor to the paper holder to compensate for the width difference 1 Open the front door 2 Press the paper holder release button and pull the paper holder out im Press the latch on top of the paper holder and open the holder
56. l Quantity Price The edit menu appears This menu gives access to the Crop amp Rotate Color Adjustment Red Eye Reduction and Sepia Black amp White functions Main Image Menu Selection Touch a button to select menu 71 SS Crop amp Rotate Red Eye Reduction ae Er Color Adjustment Sepia B amp W For details on editing see the section Image Editing on page 45 1 O Touch the Print button Print Size Total Quantity Price Image Selection gt Main Menu Edit The order contents are shown In Event mode the order contents are not shown and printing starts directly 11 Verify the order contents and enter the password For details on this operation see Verifying Order Contents and Entering a Password on page 37 Using Border Print When printing images stored on the memory card you can select from a variety of border designs to be printed around the image and you can also enter text to be printed This function is available in Full mode and Event mode To use this function the expansion CompactFlash card must be inserted You can load new border designs and enter text characters from the administration screen For details see the section Template Tab on page 25 1 Touch any place on the screen Touch screen to start i MEMORY STICK PRO xD Picture Card EM Standard DUO The language selection screen appears When using Event
57. lowing when using the Bluetooth communication for printing e An expansion CompactFlash card is inserted For more on expansion CompactFlash cards see Preparing an Expansion CompactFlash Card on page 19 The firmware version on the unit is 2 0 or later You can confirm the firmware version by displaying the system logs from the Administration tab on the administration screen For details see Administration Tab on page 28 uonejedo p 18 1dEUD Inserting the adaptor Insert the Bluetooth USB adaptor not supplied into the USB port host on the back of the unit Requirements for Bluetooth communication Compatible profiles This unit supports the following profiles BIP Basic Imaging Profile OPP Object Push Profile For details on profiles supported by your Bluetooth compatible device refer to the operating instructions for that device What is a profile A profile is a set of definitions used for Bluetooth communication There are a number of different profiles that are used depending on the purpose and specific characteristics of the devices involved To communicate via Bluetooth both devices must support a common profile 50 Printing With Bluetooth Communication Printable file formats JPEG DCF 2 0 compatible Exif 2 21 compatible JFIF 4 4 4 4 2 2 4 2 0 baseline JPEG formats TIFF Exif 2 21 compatible BMP 24 bit Windows format Depending on the format some images may not be suppor
58. memory card is inserted a slot and flashes when a memory card is being accessed Memory Stick slot page 32 Holds a Memory Stick with stored image data xD Picture Card slot page 34 Holds an xD Picutre Card with stored image data Q SD Card MultiMediaCard slot page 33 Holds an SD Card or MultiMediaCard with stored 1mage data Q SmartMedia card slot page 33 Holds a SmartMedia card with stored image data Q CompactFlash card slot page 32 Holds a CompactFlash card with stored image data To avoid loss of image data or damage to the main unit never attempt to insert a Memory Stick SmartMedia card SD Card or MultiMediaCard into a CompactFlach type adapter set in the CompactFlach slot Eject slot The printed photo emerges from this slot Paper tray page 18 Printed photos are collected in this tray Paper eject stopper page 18 When using the print pack 2UPC C13 this stopper should be raised Front door page 12 Open this door to change the paper roll Controls and Functions 9 suoneledeld z 19 dEUD suoleledolgd z 129 dEUD 10 Front door open prononayo Q Paper holder page 12 The paper roll is inserted here The white areas between printouts are cut off and collected in the top portion of the paper holder Q Paper holder release button page 12 Press this button to remove the paper holde
59. mode and when only one language was selected at the administration screen the language selection screen does not appear Instead the Main Menu appears In this case proceed to step 3 Using Border Print 41 uoneJedo p 1e1deu5 uoqeledO y 13 deypo 42 2 Touch the language you want to use Please select language Over Precautions about using the unit are shown Read these carefully and then touch the OK button When a Bluetooth USB adaptor is inserted and Bluetooth communication is enabled the device selection screen appears Touch Memory Card Insert the memory card into the respective slot on the front side of the unit When the memory card is recognized the Main Menu appears 4 Touch Border Print Touch a button to select menu Split Image Border Print Start Over The border selection screen appears Using Border Print D Select the desired border by touching it and then touch the OK button Wj button A list of images stored on the memory card is shown Select the image to be printed by touching it Print Quantity Print Size Total Quantity Price To deselect an image that you have selected touch that image again To select all images touch the Select All button If there are more images than fit on one list display screen the 4 and P buttons can be used to move among screens 7 Specify the number of copies quantity to pri
60. n button Next touch the button enter the maximum number of prints using the numeric keypad that appears on the screen and touch the OK button Order Sets the maximum number of prints that can be handled as one order You can set the maximum number of prints per order to any value from 1 to 500 The maximum number of prints per order remains in effect even when the other modes are selected Rental Sets the maximum number of prints that can be handled by the unit This mode is suitable for use when renting out the unit as printing beyond the maximum number set is not possible You can set the maximum number of prints to any value from 1 to 9999 To clear the print total touch the button and reset the maximum number of prints Ink ribbon Determines the maximum number of prints based on the remaining ink on the ribbon cartridge at the time of printing You cannot set a maximum number of prints when this button is selected The maximum number of prints for a single image is 99 prints The maximum number of prints per order remains in effect even when the other modes are selected When Rental mode is selected the remaining number of prints available 1s displayed When this display reaches 0 printing is not possible until the maximum number is reset Setting Items Password Allows you to set whether a password must be entered before printing starts When set to ON a password is required in Full mode and
61. nd setting up passwords These settings are made from the administration screen You can also use the administration screen later to change settings and to adjust the unit To bring up the administration screen proceed as follows Before you can make settings on the administration screen you must enter the administrator password In the factory default condition the administrator password is set to 9999 If a memory card is inserted in any of the front side memory card slots of the unit the administration screen does not come up Remove any memory cards first and then repeat the procedure At the Start Guide display touch the top left corner of the screen twice in succession TacgcNcreen to start wemorysticxpro M D Picture Card E Standard DUO P L I TUT vr mn EL SD Card SmartMedia CompactFlash MultiMediaCard J The password entry screen appears Enter the password using the numeric keypad Setup Procedure Chapter 3 Touch the OK button The administration screen appears T O 6g at Print Head Adjustment Cleaning Touch Panel By touching one of the tabs at the top of this screen you can select the respective category to make settings For details on each category see the section Setting Items on page 23 System tab Lets you select the language to be used by the system the beep ON OFF setting and the computer connection
62. nezuelan Bolivar MM East Carribbean Dollar Price Indi i Peruvian Nuevo Sol a S gt selection and preview screens Uruguayan Peso Currency gt Selects the currency to use when calculating the price for Pricing an order When you touch the button a list of currencies such e 3x5 4x6 5x7 as indicated below appears Touch the currency to use and Lets you set the price per print for each size touch the OK button When not displaying the currency Touch the button Using the numeric keypad that select 12 34 to display decimal points or 1234 not appears enter the value Then touch the OK button to display decimal points The price setting range 1s 0 9999 0 99 99 depending on currency abbreviation ndex Print Border Print Split Image AD Australian Dollar Lets you set the additional cost for the respective print caD Canadian Dollar function The sum of the per print price and the Touch the button Using the numeric keypad that The price setting range is 0 9999 0 99 99 depending Taiwan New Dollar New Zealand Dollar Setting Items 2f dnies e Jejdeu5 28 Administration Tab CSJON NEBECACEJ 2 Max Prints EB PAs ar Password Budget code ON ON OFF Administrator Password Checkout Password Reset to Factory Print Logs System Logs Settings Max Prints Sets the maximum number of prints that can be handled First select a Max Prints mode Order Rental Ink ribbo
63. nits with serial numbers starting with 11 only Press this button to turn on power to the unit Press it again to enter the standby mode To restart the unit from standby mode wait at least 5 seconds in standby mode and then press the On Standby button Q RS 232C interface Serves for future expansion Currently not used Q Air vent Features a built in filter for the thermal head cooling fan Q POWER switch for units with serial numbers starting with 51 only Turns the unit on or off Installation Connecting the Power Cord Connect the supplied power cord to the AC IN connector on the back of the unit and then connect the plug to a power outlet mm Power outlet Adjusting the Display Angle The display angle can be adjusted to make the display more easily viewable Eight settings are available for angle adjustment When storing the unit pull the display forward until completely upright and then push it backward until horizontal Installation 11 suonejedejd z Je1deu 5 suoleledolgd z 19 dEUD 12 Loading Paper Roll and Ribbon Cartridge Handling the paper roll and ribbon cartridge The print pack contains two ribbon cartridges and two paper rolls Be sure to use the ribbon cartridge and paper roll in the same carton as a set See Ribbon Cartridge and Paper on page 61 The number of sheets that can be printed depends on the print pac
64. nt Use the and buttons to specify the quantity ER Print Size Total Quantity Price If the Select All button has been selected the quantity set with the and buttons will apply to all images The quantity specified for an image is shown at the top right corner of the thumbnail If you wish to print without editing the images proceed to step 10 To perform editing proceed to step 8 In Quick Print mode image editing is not possible Print Size Total Quantity Price The preview screen appears 9 To edit an image touch the Edit button Print Size Total Quantity Price The edit menu appears This menu gives access to the Crop amp Rotate Color Adjustment Red Eye Reduction and Sepia Black amp White functions Touch a button to select menu ET SS Crop amp Rotate Red Eye Reduction ro a Color Adjustment Sepia B amp W For details on editing see the section Image Editing on page 45 1 O Touch the Print button Select All Print Size Total Quantity Price The order contents are shown Using Border Print uonejedo p J8 1dEUD 43 uoqel1odO p Je1deu 44 In Event mode the order contents are not shown and printing starts directly 11 Verify the order contents and enter the password For details on this operation see Verifying Order Contents and Entering a Password on page 37 Printing All Images on a Memory
65. ovided by the unit In addition to normal printing this includes Split Image print Index Print and Border Print Image editing is also possible You can require the input of a password before printing is carried out Setting Items Event Mode This mode is designed for providing free access to printing functions for example at a party wedding reception or similar The mode is also suitable for use by shop employees rather than customers No password entry or price confirmation are required before starting to print Promotional Images Allows you to set the promotional images Up to two images can be specified for display during standby in Full mode or Quick Print mode In the default condition the Start Guide is used as standby screen When one or two images have been specified these are shown alternately with the Start Guide To use the promotional image function an expansion CompactFlash card is required For information on the expansion CompactFlash card see the section Preparing an Expansion CompactFlash Card on page 19 You may create your own promotional image using commercially available photo editing software Promotional image specifications mage size 640 W x 480 H pixels e File format 24 bit Windows BMP e File name Image 1 promol bmp Image 2 promo2 bmp e File storage location Sony UPCR Promotion 7x1 Import promotional image This button lets you import a promotional 1mage from memo
66. per functioning when connected via a USB hub is not guaranteed Creating password files 1 Insert an expansion CompactFlash card into the expansion CompactFlash card slot 2 Open the Administration tab on the administration screen and set a checkout password ig 6 EB CACI Budget code Max Prints Password ON ON OFF Administrator Password Checkout Password Reset to Factory Print Logs System Logs Settings For details see Administration Tab on page 26 3 Touch the OK button The password file is created in the root folder of the expansion CompactFlash card under the name snaplab txt Existing files with the same name will be overwritten The following is contained in the file Entering Passwords Using Memory Cards Remote Password Input password pass x x is the password you set 4 Remove the expansion CompactFlash card and copy the password file into the root folder of the memory card you intend to use The password file cannot be used to enter passwords directly from the expansion CompactFlash card A password file is not created when an administrator password is set Entering passwords using memory cards 1 Connect a card reader to the USB port host 2 When the password confirmation screen appears during a print operation insert the memory card containing the password file into the card reader Please input password then press OK Ew zii po
67. r D Side door page 15 Open this door for replacing the ribbon cartridge and inserting the expansion CompactFlash card Side door open O Ribbon cartridge access opening page 15 Mount the ribbon cartridge here Q Expansion CompactFlash card slot page 19 When using border print promotional images display text input or print spool insert the expansion CompactFlash card here Controls and Functions Rear For units with serial numbers starting with 11 The seven digit serial number is located here For units with serial numbers starting with 51 Q USB port host Allows connection of a USB device You can connect a commercially available card reader or USB flash memory device to this port and use it to read data To use Bluetooth communication insert a Bluetooth USB adaptor here 1 Correct operation with every card reader and USB flash memory device is not guaranteed Operation is not guaranteed when connected by a USB hub PictBridge is not supported Q USB port device page 53 Use a USB cable to connect the unit to a computer 1 Operation is not guaranteed when connected by a USB hub AC IN Power Source Connector page 11 Connect the supplied power cord here Display stand Use this stand to adjust the angle of the display Q On Standby button for u
68. r of files to be handled 9 999 files for a memory card 8 inch touch sensitive TFT color display 640 x 480 pixels RGB Accessories supplied Paper Tray 1 Paper Holder 1 Paper Core 1 Adaptor left 1 Adaptor right 1 Power Cord 1 Cleaning Cartridge 1 USB Cable 1 790 081 71 Sony 1 P Ferrite Core 1 2 CD ROM 1 Software License Agreement 1 Before Using this Printer 1 Warranty Card 1 1 For units with serial numbers starting with 11 only 2 For units with serial numbers starting with 51 only LCD display Optional accessories Self Laminating Color Printing Pack 2UPC C13 2UPC C14 2UPC C15 Bluetooth USB adaptor DPPA BT1P 2 1 May not be commercially available depending on your country or region Consult your local Sony dealer 2 The Bluetooth communication function for this unit can only be used with DPPA BT1 adaptors All other Bluetooth USB adaptors are not supported Design and specifications are subject to change without notice Notes e Always verify that the unit is operating properly before use SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING BUT NOT LIMITED TO COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF FAILURE TO PRINT CONTENT OF ANY TYPE OR LOSS OF DATA DUE TO FAILURE OF THIS UNIT OR ITS PRINTING MEDIA ASSOCIATED SOFTWARE EXTERNAL STORAGE OR OTHER EXTERNAL DEVICE SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING BUT NOT LIMITED TO COMPENSATION OR REIMBUR
69. round the core make sure to wind it tightly before installing the paper roll Otherwise a malfunction may occur Do not grasp the paper too tightly or strike it against a hard object because the paper may tear or crease effecting the print quality 2 Open the front door Press the paper holder release button and pull the paper holder out 14 Installation 4 Press the latch on top of the paper holder and open the holder L S aD 5 a v 6 O O D Insert the paper roll into the paper holder The arrow on the label in the center of the paper roll must point inwards When installing the paper roll make sure the paper holder is completely open Otherwise a malfunction may occur Remove the label in the center of the paper roll Make sure to fully remove all labels from the paper roll If labels remain inside the printer operation problems may occur After inserting the paper roll do not touch the printing surface the inner surface of the rolled paper Fingerprints sweat creases etc can lead to reduced print quality nsert the paper roll firmly and completely into the paper holder T Close the paper holder Q Close the front door When closing the paper holder take care that the leading edge of the paper roll does not stick out of the paper fee
70. ry card inserted front side memory card slot If an error message appears check the following likely causes The expansion CompactFlash card has insufficient free space The file selected for copying is not in the specified folder or does not meet the promotional image specifications If there are promotional images already stored on the expansion CompactFlash card they will be overwritten Be careful when performing this procedure because even read only files will be forcibly overwritten e mage 1 Image 2 Selects the time period for which the promotional image is displayed When the time has elapsed the unit automatically switches to the next image When OFF is selected the promotional image is not shown It is not possible to set Image 1 Image 2 and Start Guide all to OFF at the same time Start Guide Selects the time period for which the Start Guide is displayed When the time has elapsed the unit automatically switches to the promotional image When OFF is selected the Start Guide 1s not shown It is not possible to set Image 1 Image 2 and Start Guide all to OFF at the same time Template Tab Text Input Steve and Janet s Wedding June 14 2007 Text Setting ON This lets you load and delete templates for border print and enter text to be generated To use the Template tab an expansion CompactFlash card is required For information on the expansion CompactFlash card see the section
71. s The print paper is drawn into and then reemerges from the eject slot which removes any foreign particles and grime inside the printer When cleaning finishes the print paper is cut several times After cleaning is finished make sure the cleaning sheet is completely ejected If any part of the cleaning sheet remains on the print paper remove the paper holder and cut off all the remainders before using the printer 1 O Remove the cleaning cartridge and reinsert the ribbon cartridge Print paper is needed to perform cleaning If there is insufficient print paper remaining an error message may appear Replace the print paper and try performing cleaning again The print paper used during cleaning is trimmed off automatically Cleaning xipueddy o9 xipueddy 60 When the cabinet becomes dirty If the cabinet 1s extremely dirty soak a clean cloth in water or a solution of water and a neutral detergent wring out the cloth and then wipe the surface of the cabinet Next wipe clean with a clean dry cloth To avoid damaging the surfaces of the unit never use thinner benzene alcohol or any other type of organic solvent to clean the unit When the display becomes dirty When the display has become considerably dirty wipe it clean with a dry cloth or with a clean cloth soaked in water and thoroughly wrung out Do not use even a mild detergent as it can damage the surface of the display Never touch or
72. spare paper will be left over Remove the leftover paper and load a new ribbon cartridge and paper roll page 13 There is a white margin on the printed image The print position may not be correct Adjust the print position page 26 Depending on the display angle the display may not be visible or may be difficult to see The display angle can be adjusted Adjust the angle of the display to improve the display appearance page 9 Display not on or difficult to see Image data cannot be read A mounted memory card does not contain any data Insert a memory card that contains image data Data has been recorded on a memory card in a format that the unit does not recognize Be sure to store image data in a format that the unit can recognize page 55 The memory card may not be properly inserted Make sure that the memory card is fully inserted page 32 The memory card may not be inserted in the correct direction Set the memory card in the direction shown on the operation screen Ribbon Cartridge and Paper Each printing pack contains two sets of the ribbon cartridge and paper roll combination Be sure to use the ribbon cartridge and the paper roll in the carton as a set 2UPC C13 series Self Laminating Color Printing Pack Contains color ribbon cartridge and paper Ribbon cartridge for printing 2 rolls 3 5 x 5 inches print paper 2 rolls 2UPC C14 s
73. t the MagicGate standard material recorded with this unit is not protected by MagicGate In addition you can also use Memory Stick Duo or Memory Stick PRO with your unit Notes on MagicGate MagicGate is the collective name of content protection technologies developed by Sony Write protecting Memory Stick data In order to protect important data from accidental erasure the Memory Stick has a write protect switch When the switch is in the left hand position data can be written to or deleted from the Memory Stick and the Memory Stick can be initialized When the switch is in the right hand position data in the Memory Stick can be read but cannot be written When inserting a Memory Stick into this unit in order to read data slide the write protect switch to the protected state Contacts Write protect switch Write protected Not write protected LOCK LOCK Label area The write protect switch position and shape varies depending on your type of Memory Stick Reinitializing formatting Memory Stick Before using your Memory Stick for the first time make sure that you use your digital camera to format it Formatting the Memory Stick with a device other than your digital camera may make data on the Memory Stick unreadable for the system Notes on using Memory Stick To use a Memory Stick insert it directly into the Memory Stick slot of the
74. ted Maximum number of pixels that can be handled 8 000 x 6 000 dots Depending on the available space on the expansion CompactFlash card the number of images that can be received may differ Printing from Bluetooth compatible devices You can send images from Bluetooth compatible devices such as mobile phones and print them 1 Touch any place on the screen Touch screen to start F a j MEMORY STICK PRO xD Picture Card Standard DUO N The language selection screen appears 2 Touch the language you want to use Please select language Start Over The device selection screen appears 3 Touch Bluetooth Select your picture source al m r Memory Card Start Over The transfer screen appears Operate your Bluetooth compatible device and send the images For details on how to send the images refer to the operating instructions for your Bluetooth compatible device When selecting a printer on your Bluetooth compatible device select SONY UP CRIOL The alpha numeric characters comprising the right side of the Bluetooth address displayed on the printer s screen appear in place of CF appears in place of HH in the following sample screen Please send your pictures then press OK when transfer is complete Passkey PIN Number of received images Remaining memory The unit receives the image data sent The number of
75. the A mark on the xD Picture Card facing up and forward completely insert the xD Picture Card into the slot When you insert the xD Picture Card into the unit it is automatically detected Removing the xD Picture Card When you see a message that prompts you to remove the xD Picture Card first push the xD Picture Card until you hear a click then pull 1t out To prevent losing valuable data or damaging the xD Picture Card never remove the xD Picture Card from the slot until the message prompts you to remove it Using Bluetooth communication Using an optional Bluetooth USB adaptor you can send images wirelessly from Bluetooth compatible devices such as mobile phones For details on sending images using Bluetooth communication see Printing With Bluetooth Communication on page 50 The following sections give explanations on how to print images from a memory card The same procedure can be used to print images sent using Bluetooth communication Selecting Images for Printing Selecting Images for Printing The procedure for selecting images from the inserted memory card is described below This procedure can be carried out in any operation mode 1 Touch any place on the screen Touch screen to start LE MEMORY STICK PRO P r LL Standard DUO i a xD Picture Card mm SD Card CompactFlash MultiMediaCard The language selection screen appears When using Event mode and when only one language
76. the entire folder for each desired print size into it A CompactFlash card with at least 512 MB of free space is required to copy all the data stored on the CD ROM If you have copied the CD ROM data to a memory card other than a CompactFlash card you will need to use the unit to copy it from that memory card to a CompactFlash card For details on copying the data see Template Tab on page 25 Inserting the expansion CompactFlash card 1 2 3 Open the side door S gt Insert the expansion CompactFlash card that you have created into the expansion CompactFlash card slot Close the side door TULIT Installation suonejedejd z Je1deu 5 19 suoleledolgd z 19 dEUD 20 Startup and Shutdown Startup Start the unit as follows For units with serial numbers starting with 11 Verify that no memory card is inserted in any of the front side memory card slots of the unit Then press the on standby button For units with serial numbers starting with 51 Verify that no memory card is inserted in any of the front side memory card slots of the unit Then turn on the POWER switch Startup and Shutdown The unit starts up and the
77. ublimation thermal transfer Resolution 300 dpi Gradations YMC images process using 8 bits 256 gradations per color 2UPC C13 89 x 126 mm 2 mm 3 5 x 5 inches 3 32 inch 2UPC C14 101 x 152 mm 2 mm 4 x 6 inches 3 32 inch 2UPC C15 126 x 178 mm 2 mm 5 x 7 inches 3 32 inch Image data transferred 2UPC C13 1 100 x 1 536 dots 2UPC C14 1 248 x 1 848 dots 2UPC C15 1 536 x 2 148 dots The top and bottom and right and left portions will not be printed by about 2 mm 2UPC C13 Approx 13 sec 2UPC C14 Approx 16 sec 2UPC C15 Approx 17 sec Input connector AC IN for power Control connector RS 232C External control interface D SUB 9 pin connector 1 USB function port Hi Speed USB USB2 0 USB host port for the USB flash memory Memory card slots Memory Stick interface slot 1 SD Card interface slot 1 CompactFlash card interface slot 2 One of the two slots is used as expansion slot located inside the side door SmartMedia card interface slot 1 xD Picture Card interface slot 1 Picture size Printing time Specifications Compatible image file formats JPEG JFIF 4 4 4 4 2 2 4 2 0 baseline JPEG Exif 2 2 1 compatible DCF 2 0 compatible TIFF Exif 2 2 1 compatible TIFF RGB non compressed BMP 24 bit Windows format Some versions of the file formats may not be compatible Maximum number of pixels to be handled JPEG 8 000 H x 6 000 V TIFF 8 000 H x 6 000 V BMP 8 000 H x 6 000 V Maximum numbe
78. unit When making the connection you should also consult the documentation of the computer USB cable mz Computer If the connection is made via a USB hub correct operation is not assured For units with serial numbers starting with 11 This unit is supplied with a USB cable with a ferrite core already attached Always use this supplied USB cable when connecting to a computer For units with serial numbers starting with 51 Attaching a ferrite core to a USB cable Before connecting a USB cable not supplied to the printer you should attach a supplied ferrite core to its cable for noise prevention To conform to radiation standards attach the supplied ferrite core to the USB cable of your device as described below Release two stoppers on the ferrite core to open it 2 Slip the USB cable through the ferrite core and p 8 position it at the base of the USB connector to the printer Close the ferrite core until you hear a click When the ferrite core cannot be secure because the USB cable is thin secure it using a tape Printing From a Computer uoneJedo y 1e1deu5 53 xipueddy 54 Appendix Precautions Safety Operate the printer using the power source specified in Specifications on page 62 Be careful not to damage the power cord by placing or dropping heavy objects on it it is dangerous to use the unit with a damaged
79. upported file formats The unit supports the following file formats The maximum data size that can be read by the unit is 8 000 x 6 000 pixels e JPEG JFIF 4 4 4 4 2 2 4 2 0 baseline JPEG Exif 2 2 1 compliant DCF 2 0 compliant e TIFF Exif 2 2 1 compliant RGB non compressed e BMP 24 bit Windows format Some format versions may not be supported Up to eight levels are supported for directories on a memory card and up to 9 999 files can be handled with a single operation Notes on Using Memory Cards Sony bears no responsibility for damage to your memory card or data while using this unit Operation of Memory Stick up to 32 GB media on this product is confirmed However proper operation on all types of the Memory Stick media is not guaranteed You cannot play back files that are 4 GB or larger in size from Memory Stick media due to the specifications of its file system Memory Stick types Memory Stick is a removable compact data storage card that can be used with digital still cameras and personal computers Still images stored in a Memory Stick can be easily displayed overwritten or deleted Memory Stick comes in two types general purpose Memory Stick and Memory Stick using the MagicGate encryption technology to protect copyrighted material referred to as MagicGate Memory Stick This unit supports both types of Memory Stick However because this unit does not suppor

Digital Photo Printer

Contents

Download Pdf Manuals

Related Search

Related Contents