Home

Pixel Storm 12 Tri Batten

1. DMX Digital Multiplex is a universal protocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions form the controller to the fixture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a data out terminal DMX linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned to a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain DATA cable DMX cable requirements for DMX operation This fixture can be controlled via DMX 512 protocol The DMX address is set on the back of the unit Your unit and your DMX controller require a standard 3 pin XLR connector for data input output see image below Further DMX cables can be purchased from all
2. Do not open the equipment and do not modify the unit temperature fluctuation e g after transportation do not connect power or switch it on immediately The arising condensation might damage the equipment Leave the equipment switched off until it has reached room temperature Do not connect this equipment to a dimmer pack e Do not switch the equipment on and off in short intervals as this will reduce the system s life e Only use the equipment indoors If your product fails to function correctly stop use Do not expose to flammable sources liquids or gases immediately Pack the unit securely preferably in the e Always disconnect the power from the mains when original packing material and return it to your Pro Light equipment is not in use or before cleaning Only handle dealer for service the power cable by the plug Never pull out the plug by pulling the power cable Repairs servicing and power connection must only be e Make sure that the available voltage is between carried out by a qualified technician THIS UNIT CONTAINS 100 240V 50 60Hz NO USER SERVICEABLE PARTS e Make sure that the power cable is never crimped or WARRANTY One year from date of purchase damaged Check the equipment and the power cable periodically Only use fuses of same type and rating OPERATING DETERMINATIONS If this equipment is operated in any other way than those described in this manual the product may suffer damage and the
3. Sh Pixel Storm 12 Tri Batten 12 x 3W tri colour LEDs RGB User Manual c no fan Order code LEDJ291 Safety advice WARNING FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP e Before your initial start up please make sure that there is no damage caused during transportation e Should there be any damage consult your dealer and do not use the equipment e To maintain the equipment in good working condition and to ensure safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual e Please note that damages caused by user modifications to this equipment are not subject to warranty CAUTION CAUTION TAKE CARE USING KEEP THIS EQUIPMENT THIS EQUIPMENT AWAY FROM RAIN MOISTURE AND LIQUIDS HIGH VOLTAGE RISK OF ELECTRIC SHOCK IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorised modification to the equipment e Never let the power cable come into contact with other If the equipment is dropped or damaged disconnect the cables Handle the power cable and all mains voltage mains power supply immediately and have a qualified connections with particular caution engineer inspect the equipment before operating again e Never remove warning or informative labels from the unit If the equipment has been exposed to drastic
4. warranty becomes void Incorrect operation may lead to danger e g short circuit burns and electric shocks etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to people and or property www prolight co uk Pixel Storm 12 Tri Batten User Manual 2 Product overview amp technical specifications Pixel Storm 12 Tri Batten The LEDJ Pixel Storm 12 contains 12 x 3W tri colour LEDs Offering full pixel mapping capabilities with individual pixel control the Pixel Storm 12 is suitable for a wide range of applications from venue uplighting to dynamic eye candy effects on stage A digital LED display with 4 push button menu system allows for easy setup e 12 x 3W tri colour LEDs RGB Beam angle 25 e Refresh rate 2kHz e Pixel mapping capabilities e DMX channels 3 3 5 or 36 selectable e Static colour colour change colour fade auto run sound active and master slave modes e O 100 dimming with variable strobe e End and central brackets allow for multiple rigging and floor standing applications e 4 push button menu with LED display e IEC power in out sockets e 3 pin XLR in out sockets e Convection cooled e Extruded aluminium chassis all metal construction Specifications Pixel Storm 12 Tri Batten 25 Lux 4056 1741 974 595 408 Power consumption 60W ee Power supply 100 240V 50 60Hz ai F T2A 250V a SEA
5. MEN tse A a ee Dimensions 135 x 1062 x 125mm Weight 5 8kg Om 1m 2m 3m 4m 5m Order code LEDJ291 1062mm 125mm N CN N a N N YN N 3 a www prolight co uk Pixel Storm 12 Tri Batten User Manual 3 Technical specifications 01 Hanging Bracket 05 LED display 09 IEC power in socket 02 Bracket tightening knobs 06 Function buttons 10 IEC power out socket diss eee 03 Floor Brackets 07 DMX input socket 11 Fuse T2A 250V Ax ices manual 04 Earth point 08 DMX output socket www prolight co uk Pixel Storm 12 Tri Batten User Manual 4 Operating instructions DMX channel mode Operating in a DMX control mode environment gives the user the greatest flexibility when it comes to customising or creating a show In this mode you will be able to control each individual trait of the fixture and each fixture independently To access the DMX channel mode press the MODE button on the rear of the unit to show ald I on the LED display Now use the UP and DOWN buttons to set the desired DMX address Now press the ENTER button to choose one of the 3 3 5 or 36 DMX channel modes press the ENTER button to confirm the setting To exit out of any of the above options press the MODE button 3 channel mode 3 channel mode Channel Value Function gt 000 255 Red 0 100 030 044 045 059 5 channel mode a 075 089 EEN 104 1 con
6. aa 119 Green 0 120 134 135 149 180 194 210 224 225 255 Hen 1is he 224 0 00 255 Sensitivity low high when channel 1 Green 0 100 i rea OOP een iS 225 255 000 255 Flash speed slow fast when RR 1 is 001 224 Es 084 Pet anang ARE 1 when channel 1 is 225 255 085 169 169 Sound 2 when channel 1 is 225 255 2 when channel 1 is 225 255 170 255 Sound 3 when channel 1 is 225 255 www prolight co uk Pixel Storm 12 Tri Batten User Manual 5 Operating instructions 36 channel mode cm cm cu cma chs che com7 che cho CH5 R1 G1 B1 R2 G2 B2 R3 G3 B3 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 CH10 CH11 CH12 CH13 CH14 CH15 CH16 CH17 CH18 R4 G4 B4 R5 G5 B5 RG G6 B6 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 CH19 CH20 CH21 CH22 CH23 CH24 CH25 CH26 CH27 R7 G7 B7 R8 G8 B8 R9 G9 B9 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 CH28 CH29 CH30 CH31 CH32 CH33 CH34 CH35 CH36 R10 G10 B10 R11 G11 B11 R12 G12 B12 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 0 255 Built in program mode To access the built in program mode press MODE until the display shows Pr I Static colours on the LED display Press ENTER to confirm the setting Use the UP and DOWN buttons to select a program from Pr I Pr IG Press the ENTER button to confirm the setting To
7. change the speed of the selected program press the ENTER button and then use the UP and DOWN buttons to select any value from SPOD 5P94 Press the ENTER button to confirm the setting then use the UP and DOWN buttons to select and value from F 5055 F594 forthe amp rb Pink strobe feature Press the ENTER button to confirm the setting In Pr O I you are able to set a specific static colour When in Fr O I press the Ho fF Blackout 5 b Blue ENTER button and then use the UP and DOWN buttons to go through the static colours Press the ENTER button to confirm the setting then use the UP and DOWN buttons to select and value from F 5050 F 5499 for the strobe feature Press the ENTER button to confirm the setting To exit out of any of the above options press the MODE button Static colour mode To access the static colour mode press ENTER until La r shows on the LED display Press the ENTER button and the LED display will show r d d5 Now use the UP and DOWN buttons to select the brightness between r 0 OD r d55 Press the ENTER button and repeat for green and blue Value 000 255 000 low 255 high To exit out of any of the above options press the MODE button www prolight co uk Pixel Storm 12 Tri Batten User Manual 6 Operating instructions Master slave mode To set the master unit p
8. en inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used The diagram below details the correct cable conversion F B A gt 5 pin XLR socket Pin 1 GND screen Pin 2 Signal Pin 3 Signal Pin 4 N C Pin 5 N C 3 pin XLR socket Pin 1 GND screen Pin 2 Signal Pin 3 Signal 5 pin XLR socket 3 pin XLR socket Pin 1 GND screen Pin 1 GND screen 5 Pin 2 Signal Pin 2 Signal Pin 3 Signal Pin 3 Signal Pin 4 N C Pin 5 N C www prolight co uk Pixel Storm 12 Tri Batten User Manual 9 WEEE notice Correct Disposal of this Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries Si with separate collection systems This marking shown on the product or its literature indicates that it should not be disposed of with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their suppl
9. good sound and lighting suppliers or Pro Light Concepts dealers Please quote CABL10 2m CABL11 5m CABL12 10m Also remember that DMX cable must be daisy chained and cannot be split www prolight co uk Pixel Storm 12 Tri Batten User Manual 8 DMX setup Notice Be sure to follow the diagrams below when making your own cables Do not connect the cables shield conductor to the ground lug or allow the shield conductor to come in contact with the XLRs outer casing Grounding the shield could cause a short circuit and erratic behaviour common DMX 512 out DMX 512 in 3 pin XLR 3 pin XLR KEN ED NR DN RE XLR MALE SOCKET XLR FEMALE SOCKET XLR Pin Configuration 2 cold 1 ground 1 ground 2 cold Pin 1 Ground Q Pin 2 Negative 3Hot 3Hot Pin 3 Postive Special note Line termination When longer runs of cable are used Termination reduces signal transmission you may need to use a terminator on problems and interferance it is always the last unit to avoid erratic behaviour advisable to connect a DMX terminal _ resistance 120 Ohm 1 4 W between pin 2 Using a cable terminator will decrease DMX and pin 3 DMX of the last fixture the possibilities of erratic behaviour 3 pin Order ref CABL90 5 pin Order ref CABL89 5 pin XLR DMX connectors Some manufactures use 5 pin XLR connectors for data transmission in place of 3 pin 5 pin XLR fixtures may be implemented in a 3 pin XLR DMX line Wh
10. ier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal CE f www prolight co uk Pixel Storm 12 Tri Batten User Manual 10 www prolight co uk Pixel Storm 12 Tri Batten User Manual 11 www prolight co uk Pixel Storm 12 Tri Batten User Manual 12
11. ress the MODE button on the rear of the master unit then select your desired program sound active auto static colour or one of the built in programs To set the other units in slave mode press the MODE button on the rear of the unit to show SL AU on the LED display and press the ENTER button to confirm the setting The units will now run in sequence with the master unit To exit out of any of the above options press the MODE button Please ensure that all slave units are set to the same DMX channel mode as the master unit Sound active mode To access the sound active mode press the MODE button on the rear of the unit to show SUG on the LED display Now press the ENTER button and use the UP and DOWN buttons to set the sound sensitivity level from SHOO SHJ I and press the ENTER button to confirm the setting Value 00 31 00 low 99 high To exit out of any of the above options press the MODE button Auto mode To access the auto mode press MODE until the display shows Aut onthe LED display The unit will now run through the built in programs Fr O cd Pr 16 Now press the ENTER button and use the UP and DOWN buttons to set the number of times the unit runs through each program from nn i nn MOAL M UL Value 001 100 001 runs through each pattern once 100 runs through each pattern 100 times Press the ENTER button to confi
12. rm the setting Now use the UP and DOWN buttons to set the speed the unit runs through each program SA OO 5P99 Press the ENTER button to confirm the setting then use the UP and DOWN buttons to select and value from F 500 F 5499 for the strobe feature Press the ENTER button to confirm the setting Value 00 99 00 slow 99 fast To exit out of any of the above options press the MODE button Menu system Pr 16 Macro 15 G0 5P99 speed 00 F 599 flash Built in program Pr O I Static colour Pr O0d Macro 1 Pr 03 Macro 2 Pr 04 Macro 3 Pr 05 Macro 4 Pr 06 Macro 5 Pr 0 Macro 6 Pr 08 Macro 7 Pr 09 Macro 8 Pr ID Macro 9 Pr 1 1 Macro 10 Pr Id Macro 11 Pr 13 Macro 12 Pr 14 Macro 13 Pr 15 Macro 14 Address setting ADD I A5 i2 www prolight co uk Pixel Storm 12 Tri Batten User Manual 7 DMX setup Setting the DMX address The DMX mode enables the use of a universal DMX controller Each fixture requires a start address from 1 512 A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address For example a fixture that occupies or uses 7 channels of DMX and was addressed to start on DMX channel 100 would read data from channels 100 101 102 103 104 105 and 106 Choose a start address so that the channels used do not overlap E g the next unit in the chain starts at 107 DMX 512

Pixel Storm 12 Tri Batten

Contents

Download Pdf Manuals

Related Search

Related Contents