Experiment manual
Contents
1. wwww cebekit es SOLAR HYDROGEN EDUCATION KIT Experiment manual CE Model No C 7112 AN Warning To avoid the risk of property damage serious injury or death This kit is intended only for use by persons 12 years old and up and only under the supervision of adults who have read and understood the instructions provided in the kit s user manual Keep children under the age of 12 away as it contains small parts that could be swallowed The Reversible Fuel Cell generates gases that are very easily ignited Read the instructions carefully before use and have them ready for refer ence Experiment manual Table of Contents 1 General safety instructions 2 Discovering solar photovoltaic energy 3 Introduction of the reversible fuel cell 4 About the solar hydrogen education kit 5 List of components 6 Experiments 7 Advice for optimal use 8 Troubleshooting Part 1 General safety instructions To avoid the risk of property damage serious injury or death 1 Read carefully and fully understand the instructions before starting assembly of this kit 2 This kit is intended only for use by persons 12 years old and up and only under the supervision of adults who have read and understood the instructions in this user manual 3 When assembling this kit tools may be used Extra care should be taken to avoid personal injury 4 Some parts are small and fragile please be careful when handli2. Solution 2 Replace the old batteries with new one in the battery pack 4 The load can not work while there is hydrogen left in the inner container Solution Unplug the black pin of the short tube on the reversible fuel cell and quickly attach the pin back to the tube see page 21 You can see the load working well again 5 No hydrogen is produced under the sunlight Solution If the sunlight is not strong enough electricity will not be created Use the battery pack provided to perform the electrolysis using the reversible fuel cell If you have any further issues contact support horizonfuelcell com 26 27 Battery pack operation instructions 1 The removing and inserting of batteries is to be conducted by the adults only Unscrew the screw holding the battery pack s cover in place using a screw driver Once the screw is removed open the battery pack and take out the batteries using your fingers Do not use a metal object When inserting the batteries make sure that you are doing so with the correct polarity the positive end of the battery must match up with the and the negative end of the battery must match up with the sign indicated on the battery pack close the battery pack and secure its cover by tight ening the screw with a screw driver 2 Non rechargeable batteries are not to be recharged 3 Different types of batteries such as rechargeable alkaline and standard batteries or new and used batt
3. generating DC current The greater the intensity of the light the greater the flow of electricity oolar pv is quite different from a solar thermal system where the sun s rays are used to gen erate heat usually for hot water in a house or swimming pools How a Photovoltaic Cell Works wed n type silicon aoe _ electric field Costs for solar photovoltaic power generation are still high but have decreased over the past 20 years New generations of solar pv technologies are emerging as a result of new materials research In the next years we may see inexpensive solar pv materials printed like newspapers on rolls of flexible film Flexible solar pv materials are already being rolled out on the rooftops of ware houses and some of these warehouses are now able to supply energy back into the local power grid during energy demand peaks Part 3 Introduction of the reversible fuel cell The reversible fuel cell is very unique because it is both an electrolyzer and a fuel cell combined into one device When applying an electric current the device acts as an electrolyzer that produces hydro gen and oxygen from de ionized water When applying a load the electrolyzer becomes a fuel cell and generates electricity from hydrogen A Fuel cell function of the reversible fuel cell how does it work A fuel cell is a device that can convert hydrogen to usable electric power The fuel cell is an assembly of advanced materia
4. from the upper nozzle of the reversible fuel cell and the water will descend into the inner container appropriately 6 The reversible fuel cell in the open air is very sensitive to volatile organic compounds which will affect the performance of it So when you finish using the kit it is highly recommended to place the reversible fuel cell inside an air sealed plastic bag such as a Ziploc bag This will protect the reversible fuel cell while you are not using your kit 24 25 Part 8 Troubleshooting 1 The water levels do not drop when the gas outlet tubes on both sides of the reversible fuel cell are unplugged Solution Check whether the holes on the wall of the inner cylinder are blocked If so turn the inner cylinder until water enters the holes and fills up the inner cylinder 2 The reversible fuel cell does not produce hydrogen and or oxygen Solution 1 Check whether the wires are appropriately connected and whether there are any loose connec tions The reversible fuel cell could be completely destroyed if the red wire of the battery pack is connected to the black jack of the reversible fuel cell Solution 2 Make sure the batteries are inserted with the correct polarity Solution 3 Replace the old batteries with new one in the battery pack 3 The water electrolysis process slows down Solution 1 Inject water to the oxygen side of the reversible fuel cell by using the syringe and wait for about 3 minutes
5. fuel cell C Disconnect the syringe J from the nozzle tube and attach the red pin to the tube Let the reversible fuel cell settle for 3 minutes Place the water container base H with the Horizon logo facing towards you Insert the hydrogen outer storage containers D into one of the round slots located on the water container base H see D Insert the oxygen outer storage containers E into the other round slot on the same base see E Insert the two inner containers F into the hydrogen and oxygen outer containers D amp E see E amp F Note There are two openings at the bottom of each of the inner containers F These openings allow for gas to escape the inner containers F into the outer containers to limit the amount of gas stored Make sure these openings are not blocked by the raised plastic frame holding the inner containers F Push on the top of the inner containers F to be sure they fit firmly onto the plastic rim located at the bottom of the outer storage containers Use scissors to cut out one 16cm long tube e Connect one end of this tube to the nozzle of the inner hydrogen container see G Connect the other end of this tube to the lower nozzle on the hydrogen side of the reversible fuel cell see H 12 e Use scissors to cut out another 16cm long tube e Connect one end of this tube to the top nozzle of the inner oxygen container Connect the other end of the tube to the
6. lower nozzle located on the oxygen side of the reversible fuel cell see I e Pour about 40ml distilled or purified water into the outer hydrogen and oxygen containers respectively reach upper 20 marks on the outer container see J Note The water filling container is not provided in this set You can use any other water container but make sure the container you use is clean 19 Disconnect the red pin of the short tube on the oxygen side of the reversible fuel cell see K You should observe that water fills the inner container Once it is full connect the red pin back onto the short tube Repeat the same step on the hydrogen side If the water cannot flow into the inner container please see Note on page 11 to solve the problem Re ow a Use the solar panel to turn solar energy into hydrogen Connect one end of the red and black cables B to the solar panel A Connect the other end of the cables to the reversible fuel cell C being careful to match up red plug with red socket and black plug with black socket see L f you cross the wires or do not connect these cables correctly the reversible fuel cell C could be permanently damaged Position the solar panel in the face of strong sunlight outside Look closely at the reversible fuel cell C you will notice water is slowly being displaced 14 These changing water levels show that gases are formed inside the containers hydrogen is being pr
7. make your applications work In order to maximize hydrogen utilization the key is to avoid having air nitrogen inside your hydrogen fuel cell system In order to achieve this goal we must operate several steps Make sure you have your reversible fuel cell module and hydrogen storage modules connected to each other and there is still hydrogen left in the inner hydrogen container The load is connected to the whole system Using your thumb and index finger strongly pinch the short tube located on the reversible fuel cell C so that no air passes through the tube Keep pinching the tube While you keep pinching the tube remove the black plastic pin see picture A Very slowly decrease pressure on the tube between your fingers There will come a point where gas will start coming out and very quickly As you do this keep looking at the hydrogen in the hydrogen tank to make sure you don t release too much Be quick and agile enough to release just a very tiny amount of gas and pinch the tube back again quickly to keep the maximum gas in Keep pinching the tube as you replace the black plastic pin Once the pin is back on the tube you can let go see picture B The load should work better than before due to some impure gases having been removed Note 1 You can use Horizon Fuel Cell software Adaptor FCJJ 24 to measure the fuel cell performance before and after the hydrogen purging process to have a clear view of the impac
8. continuously for more than 10 minutes at a time or the reversible fuel cell will be permanently damaged 2 After the reversible fuel cell produces hydrogen and oxygen continuously for nearly 10 minutes disconnect it from its power source Inject some distilled or purified water into the oxygen side of the reversible fuel cell to humidify the membrane for about 3 minutes see page 10 3 During electrolysis make sure the hydrogen and oxygen tubes that connects the hydrogen and oxygen supply containers to the reversible fuel cell are not clinched Otherwise the accumulated hydro gen and oxygen pressure will puncture and damage the reversible fuel cell s membrane 4 Using non distilled water will damage the electrodes of the fuel cell Fuel cells use nano scale or carbon supported platinum as a catalyst and these particles are very sensitive to impurities found in non distilled water It is highly recommended to use the distilled or purified water 5 For the purpose of this solar hydrogen education kit high quality drinking water or tap water with low mineral content can also be used however the kit s lifetime will be shortened 6 The reversible fuel cell must ONLY be hydrated through the oxygen positive side and not through the H2 side failure to do so will result in the blockage of the hydrogen flow and failure of the experiments 7 Carefully read the battery pack operation instructions before use Part 7 Advice for optimal
9. eries are not to be mixed and should be used separately 4 The battery pack cables are not to be inserted into an AC socket 5 The supply terminals of the battery pack are not to be short circuited 6 The two spare red amp black cables are not to be inserted into an AC socket 7 Exhausted batteries are to be removed from the battery pack Horizon Fuel Cell Technologies
10. he fan blade to the adaptor e Disconnect the red amp black cables from the solar panel Connect the red cable connected to the reversible fuel Make sure the fan blade is firmly secured to the adaptor cell to the red female plug on the motor cable Connect the black cable connected to the reversible fuel cell to Make sure the fan blade can rotate freely the black female plug on the motor cable Make sure all the connections are correct e Holding the motor you can now see the blue fan spinning quickly consuming the hydrogen and oxygen stored in the inner gas containers see picture below Note If the fan blade stops running while there is still hydrogen remaining in the inner gas container this implies the hydrogen is not pure in the container and tube and can not be consumed completely You can unplug the black pin on the hydrogen side of the fuel cell and quickly attach the pin back into the tube You can then see the fan running again for more detailed information see page 21 Once there is no more hydrogen gas left in the inner container no more electricity can be produced and you will see the fan blade running slowly until it stops Disconnect the red amp black cable from the motor To create more hydrogen and oxygen repeat the process starting on page 14 21 Maximizing hydrogen utilization and optimizing application run times There will be some nitrogen in the system and you will have to get rid of it to
11. l layers where hydrogen and oxygen react with each other to generate electricity and water without any combustion Serious interest in fuel cells did not begin until the 1960 s when they were used as power for man s first missions to the moon Although fuel cells still provide electricity and water for today s space missions this unique technology is now aimed at promoting a global transition to renewable energy sources Fuel cell cars that use hydrogen as fuel are called zero emission vehicles If fuel cell cars were to use hydrogen produced by renewable sources of energy such as solar or wind power our fuel supply would be unlimited and consumption of hydrogen through fuel cells would not create any waste nor air pollution Fuel H Hydrogen Used Fuel Recirculates Flow Field Plate Gas Diffusion Electrode Anode Catalyst Electric Circuit eO Y eo eO eco Li 4 Lu Air Water Vapor as Flow Field Plate Gas Diffusion Electrode Cathode Catalyst Proton Exchange Membrane magnitied PEM reversible fuel cell O2 PEM reversible fuel cell fuel cell function side view B Electrolyzer function of the reversible fuel cell how does it work Electrolysis is the use of electrical energy to produce a chemical change In the renewable hydro gen cycle electrical energy from renewable resources is used to break the bonds between the hydroge
12. n and oxygen in the water releasing them as elemental gases Hydrogen is stored renew able energy An electrolyzer is a device that facilitates the electrolysis of water to produce hydrogen gas Electrolyz ers most commonly used today generate hydrogen at relatively low pressures from nearly atmo spheric pressure up to 200 pounds per square inch and use a liquid alkaline electrolyte KOH or NaOH At these pressures storage of large quantities of hydrogen requires extremely large storage vessels One solution to this problem is to use a compressor to increase the hydrogen pressure However the energy investment required to pressurize hydrogen as well as the maintenance of hydrogen compressors makes this option difficult for a large scale application of this technol ogy Furthermore the operation of alkaline electrolyzers requires frequent maintenance that includes disposal and replacement of the highly caustic electrolyte New approaches to water electrolysis include proton exchange membrane electrolyzers which is the electrolysis function of the reversible fuel cell in this kit Such an electrolyzer can be designed to elec trochemically generate hydrogen at pressures of 2000 psi or greater thus eliminating the need for mechanical compression No caustic alkaline or acidic fluid electrolyte is required Additional ad vantages of PEM electrolysis over alkaline electrolysis include lower parasitic energy losses and higher purity hydrogen
13. ng and connecting parts to avoid breakage Handle all parts and components with care 5 Do not attempt to use any part item or component provided in this kit for any other purpose than what is instructed in this manual Do not attempt to disassemble any part item or component in this kit 6 Empty all water hydrogen and oxygen from each component after use 7 Please read carefully the battery pack operation instructions on page 27 before using it Part 2 Discovering solar photovoltaic energy Creating electricity from sunlight The Solar Hydrogen Education Kit contains a solar photovoltaic cell that will be used in most of our experiments as a way to capture renewable energy from the sun The word photovoltaic is a marriage of two words photo meaning light and voltaic refering to Volts of electricity So photovoltaic pv technology involves the generation of electricity from light The secret to this process is the use of a semiconductor material which can be adapted to release electrons the negatively charged particles that form the basis of electricity The most common semiconductor material used in photovoltaic cells is silicon an element most commonly found in sand All pv cells have at least two layers of such semiconductors one positively charged and one negatively charged When light shines on the semiconductor the electric field across the junction between these two layers causes electricity to flow
14. ng prospects of renewable energy See how renewable energy can be harnessed stored and re used in all kinds of applications and how hydrogen can be the unique link between natural sources of power and power consuming devices using fuel cell technology Enjoy this exciting science education kit and start building your own hydrogen powered world Electrolyzer function Input Voltage 1 8V 2 6V D C Input Current 20 7A e Hydrogen production rate 7ml min at 1A Oxygen production rate 3 5ml min at 1A The solar panel specifications e Dimensions 125mm x 155mm x 8mm Voltage at optimum power point 2 2V D C Current at maximum power point 450mA Note Solar module data is based on standard conditions 1 000W m2 25 C Fuel cell function Output Voltage 0 6V DC Output Current 360mA Power 210mW The reversible fuel cell specifications e Dimensions 54mm x 54mm x 17mm Total Weight 69 7 grams Part 5 List of components A Solar panel B Double headed banana plug cable C Reversible fuel cell D Hydrogen tank E Oxygen tank F Gas containers G Rubber tubes H Water container base Hose pins J Syringe K Motor L Battery pack M adaptor N Fan blade O Reversible fuel cell base You will also need the following items not included in this kit Scissors 2 AA alkaline battery Water a Distilled or purified water is highly recommended f
15. oduced on the negative side or cathode of the fuel cell and oxygen is being produced on the positive side or anode of the fuel cell The hydrogen produced will be twice the volume of the oxygen produced The hydrogen production cycle is complete when bubbles start surfacing from the inner container When bubbles start to appear disconnect the solar panel from the reversible fuel cell Activities Measuring the hydrogen and oxygen production Reversible fuel cell electrolyzer function data recording chart Gas volumes produced and ratios Volume of Hydrogen ml Volume of Oxygen ml Ratio Hydrogen to Oxygen volume Goal of this experiment Students will establish that hydrogen and oxygen are produced at a 2 1 ratio Using the battery pack to perform electrolysis in case of no sunlight Find the battery pack L and make sure the power switch is in the off position Use a screwdriver to open the empty battery pack and insert 2 AA batteries into the casing then close the lid by replacing the screws onto the battery pack Connect the red plug of the battery pack L to the red input jack of the reversible fuel cell C Connect the black plug of the battery pack L to the black input jack of the reversible fuel cell C Make sure this connection is absolutely correct Any other connection will permanently damage your reversible fuel cell module see picture below Turn the battery pack L on and watch closel
16. operation 1 Make sure you use distilled or purified water only Any other water will contain substances and minerals that can contaminate and destroy the reversible fuel cell If you notice the fuel cell starts rusting it means the appropriate water distilled or purified water was not used for your experiments 2 Make sure the reversible fuel cell is well hydrated before any electrolysis operation by filling it with water using the syringe 3 You will have maximum performance when the entire electrolysis process is repeated three to four times This is due to the increased hydration of the PEM membrane in the reversible fuel cell after repeated use Optimal temperature 20 C 30 C Make sure the outer containers are filled with purified distilled water to the top 20 mark on the outer containers before proceeding with electrolysis 4 Ensure that the small outlets on the inner containers are not blocked by the plastic rim on the bottom of the outer container Hydrogen and oxygen are lighter than water so they flow to the top of the inner container displacing the water If these small holes are blocked too much pressure will build up inside reversible fuel cell and this will cause damage to the reversible fuel cell 5 When you run the reversible fuel cell multiple times water in the upper part of the outer container might not descend to the inner container This is because a vacuum has been created in the tubing Disconnect the tubing
17. or optimal use N M alil f Part 6 Experiments Sunlight powered water electrolysis using the electrolyzer function of the reversible fuel cell Insert the reversible fuel cell C into the slot located on the reversible fuel cell base O see A Use scissors to cut out two lengths of 2cm of rubber tubing from the long rubber tube G provided in the kit Place the black pin I into one end of the 2cm rubber tube e Attach the short rubber tube with the black pin to the top nozzle on the hydrogen side of the reversible fuel cell marked H2 Attach the other short rubber tube to the top nozzle on the oxygen side of the reversible fuel cell marked O2 and place the red pin I aside see B A 4 B C Note Good ion conductivity is critical to the performance of the reversible fuel cell In order to ensure good conductivity the reversible fuel cell s membrane needs to be properly humidified In order to humidify the reversible fuel cell complete the following three steps Find the syringe J and push in its plunger in to remove all air inside Draw distilled water into the syringe On the reversible fuel cell C insert firmly the syringe J nozzle into the upper nozzle tube on the oxygen side Slowly push the plunger to let the water into the oxygen side of the reversible fuel cell see C 10 11 Stop pushing on the plunger once the water starts to come out from the chamber of the reversible
18. output PEM electrolysis is potentially a simple sustainable and cost effective technology for generating compressing and storing hydrogen Oxygen O Water HO Positive Electrode Anode 1 Water Electrolysis Reaction 2H20 gt 4H 4a OF Okeurs at Anode I 3 Protons Exchange through the membrane Electrolysis using a Proton Exchange Membrane Solid Electrolyte Proton Exchange Membrane N LA i e 4 Electrons recombine with protons to form hydrogen gas at the Cathode dH de gt 2H 3 Electrons Fiow through extemal Circuit I Magnified I I I I Negative Electrode Cathode Hydrogen H Proton Exchange Membrane P E M Electrolyzer function PEM reversible fuel cell Electrolyzer function Side View Part 4 About the solar hydrogen education kit The kit demonstrates chemistry and physics principles by experimenting with the splitting of water into its basic elements using direct renewable power generation from solar photovoltaic technology Watch the initial process of electrolysis See page 6 for more information on electrolysis using the reversible fuel cell enabling hydrogen and oxygen to be produced and stored Learn how hydrogen can be used as a renewable energy carrier that can power many applications via fuel cell technology This kit provides an excellent opportunity to learn about the exciti
19. t of this process on the fuel cell 2 You can conduct the hydrogen purging process at any time if the load stops working while the hydro gen still remains in the container 3 If the fuel cell is used for the first time to power a load it is highly recommended to follow the hydrogen purging process as on page 21 Create your own fuel cell powered application Use the hydrogen and oxygen storage system to power the applications of your imagination You can remove the fan blade from the motor and use this motor as your mechanical drive Remember to keep your power requirements low as this will reduce the drain on hydrogen Feel free to submit pictures and comments on your application developments to info horizonfuelcell com for our feed back Additional Experiments You can use Horizon Fuel Cell Software Adaptor FCJJ 24 not included to visualize experiments on you screen or to measure the fuel cell performance before and after the hydrogen purging process to have a clear view of the impact of this process on the fuel cell Also you can use Horizon Fuel Cell Software Adaptor FCJJ 24 to perform your additional experiments You can purchase the Horizon Fuel Cell Software Adaptor FCJJ 24 at http www horizonfuelcell com store htm and following instructions on the site 22 23 1 As the reversible fuel cell keeps producing hydrogen and oxygen its membrane becomes slightly warm Itis advised not to produce hydrogen and oxygen
20. y as water is displaced in the water tanks D amp E and small bubbles start appearing You will notice that they appear faster than by using the solar panel as the output power of the battery pack is higher than that of the solar panel Note Read the battery pack operation instructions on page 2 carefully before use e You will know the hydrogen container is full when bubbles start overflowing into the main water tank e Once hydrogen production is completed power off the battery pack Disconnect the red and black cables from the reversible fuel cell and place the battery pack aside e In the next experiment we use this battery generated hydrogen to supply this reversible fuel cell and power a small electric fan 17 Build your own fuel cell application Once the hydrogen gas container F is filled with hydrogen there is now a stored energy source available to power applications using the fuel cell function of the reversible fuel cell C The reversible fuel cell C will act as a H2 O2 fuel cell to power small applications See the following experiment as an example Take the small plastic adaptor M out of its packaging Position the small hole to the motor axis and connect the adaptor to it Make sure the adaptor is inserted all the way onto the base of the axis see pictures below and that the motor can rotate freely 18 e Position the motor axis with the adaptor to the fan blade Connect t
Download Pdf Manuals
Related Search