KOM300M Industrial Media Converter Hardware Installation Manual
Contents
1. KOM300M User s Manual 201110 KOM300M Industrial Media Converter Hardware Installation Manual HYLAND Kyland Technology Co LTD Publication Date Oct 2011 Version V1 0 Customer Service Hotline 8610 88796676 FAX 8610 88796678 Website http www kyland cn E mail support kyland biz No 1 12 02 2009 0 KOM300M User s Manual 201110 KOM300M Industrial Media Converter Hardware Installation Manual Disclaimer Kyland Technology Co Ltd tries to keep the content in this manual as accurate and as up to date as possible This document is not guaranteed to be error free and we reserve the right to amend it without notice to users Copyright 2011 KYLAND Technology CO LTD All rights reserved No part of this documentation may be excerpted reproduced translated annotated or duplicated in any form or by any means without the prior written permission of KYLAND Corporation KOM300M User s Manual 201110 Notice for Safety Operation This product performs reliably as long as it is used according to the guidance Artificial damage or destruction of the equipment should be avoided O Read this manual carefully and keep it for future reference e Do not place the equipment near water sources or damp areas e Do not place anything on power cable or put the cable in unreachable places e Do not tie or wrap the cable which may cause a fire risk eo Power connectors and other equipment connectors should b2. al 201110 Packing List KOM300M Industrial Media Converter 1 Hardware Installation Manual 1 Certificate of Quality including Warranty Card 1 Note After unpacking please check the accessories and the appearance of the equipment If anything is missing or damaged please contact us Product Overview KOM300M is a series of green low power consumption DIN Rail industrial media converter that can be applied extensively in wind power distribution network automation subway PIS power SCADA wastewater treatment metallurgy intelligent transportation rail transit and many other industries KOM300M support telnet and web management methods Kyvision centralized management FTP TFTP upgrade and support SNMPv1 v2 v3 LLDP HTTP Modbus and TCP KOM300M industrial media converter supports DIN Rail and panel mounting and supports IP40 protection class It provides one 100Base FX port and two 10 100Base T X RJ45 ports in the front panel 3 Structure and Interface 3 1 Front Panel KOM300M User s Manual 201110 1 PWR1 Power 1 LED gt 2 PWR2 Power 2 LED 3 1 100Base FX port LED 7 4 Run Run LED 6 g 5 1 100Base FX port 6 2 3 two 10 100Base T X RJ45 ports 7 RJ45 port Speed LED 8 RJ45 port Link ACT LED Figure 1 Front Panel 3 2 Top Panel 1 Terminal block for power input 2 Screw for grounding Figure 2 Top Panel 4 Mounting 4 1 Dimension Drawing KOM300M User s Manual 201110 o Dimen
3. e firmly interconnected and checked frequently e Do not repair the equipment by yourself unless it is clearly specified in the manual Please keep the equipment clean if necessary wipe the equipment with soft cotton cloth In the following cases please immediately remove power and contact your Kyland representative o Water gets into the equipment e Equipment damage or shell breakage e Equipment operation or performance has abnormally changed e The equipment emits odor smoke or abnormal noise KOM300M User s Manual 201110 Contents AS A o E Ee ee ee ee 5 A ase E 5 Str cture and Interact ia 5 o dani E NE A E 5 A AE a A ome eR 6 MOUTO A a E AE O N 6 AA DIMENSION Drawing Sra having a a E a a 6 A2 MOUNUNO STEPS rasse a a A a AOA 8 cable COn cl dd A 10 5 1 10 100Base T X Ethernet port cooocccccnccccccocccocncccnononococonnnnononocononnnnonnnonanonannonnnenaninons 11 5 2 OBase FX Elemel Porh sner 12 POPOWE n E E sudan aie mania Mase simtetgca 13 ore 1018 0 0 A tem ere E ar eT ee ee oe ca E ae N ee ee 14 WELD INACIO Stata E E AN 15 Management ACCESS a a a a a a 16 7 1 Connected through Ethernet Cable ocooococccccocncoccccncncccncncnconnncncncnnnonanonnnnnncncnnconoss 16 TZ MARC ICO aaa no A a e 18 Product MOGO rera a A E EA E N OA 18 Basic Features and Specifications oocccoccconconnconnconnconoccnoncncononanonnnnnrnnnnnonnonononrncanonanonannns 19 1 KOM300M User s Manu
4. er products Routine operation is not harmful to your eyes but do not look directly at the fiber port or fiber connector when the switch is powered on 5 3 Power According to the power input requirements use a 5 08mm spacing terminal block to connect power cable Note The cross section area of power cable is required to be greater than 0 75mmY and less than 2 5mm The grounding resistance requirement lt 5Q e 5 pin 5 08mm power terminal block PWR1 PWR2 LJ L 2 O O O ee a 12 3 4 5 Figure 13 5 pin 5 08mm spacing Plug in Terminal Block 5 pin 5 08mm power terminal block contact definition Table 2 Contact Definition Contact number DC wiring definition AC wiring definition Protection Ground Protection Ground 13 KOM300M User s Manual 201110 Wiring and mounting Step 1 Take the power terminal block off KOM300M Step 2 Insert the power cable into the terminal block and fix the power cable Step 3 Put the terminal block back to KOM300M with the connected cable 5 4 Grounding Chassis grounding and power terminal grounding Chassis grounding Surge grounding 18 AWG yellow green line Figure 14 Chassis Grounding and Power Terminal Grounding There is a grounding screw on the top panel of the KOM300M which is for chassis grounding One end of the chassis grounding cable is connected with the grounding screw and the other end of the cable is reliably grounded The cross section area of chass
5. in Figure 9 87654321 Figure 9 RJ45 Port Pin definition of 10 100Base T X RJ45 port is shown in Table 1 Table 1 Pin Definition of 10 100Base T X RJ45 Port Pin MDiXsignalname MDI signal name Output data TD Output data TD Receiving data RD MA Output data TD Receiving data RD 4 5 7 8 Unused Note means level polarity e Wiring Sequence RJ45 Connector RI45 Connector Wiring sequence 3 3 6 6 1 1 2 2 Figure 10 10 100M Straight through Cable Wiring 11 KOM300M User s Manual 201110 Cross over cable E R 45 Connector AJ45 Connector Wiring sequence Mau Mm who Figure 11 10 100M Cross over Cable Wiring 5 2 100Base FX Ethernet Port 100Base FX Ethernet port is equipped with FC ST SC connector and each port consists of TX transmit port and RX receive port as seen on the left in Figure 12 100Base FX port wiring is shown on the right in Figure 12 Take SC port as example ST FC wiring method is the same with SC Connect the TX transmit port of device A to the RX receive port of device B and the RX receive port of device A to the TX transmit port of device in order to transmit data between device A and device B Device B SC SC cable wiring sequence Figure 12 100Base FX Port Wiring 12 KOM300M User s Manual 201110 Note A laser is used to transmit signals in fiber cables The laser meets the requirements of level 1 las
6. is grounding cable should be more than 2 5mm The grounding resistance requirement lt 5Q The grounding part in the 5 08mm power terminal block is called surge grounding It is required to connect the chassis grounding part with the surge grounding part by an 18 AWG yellow green line as seen below 18 AWG yellow green line Unit mm 14 KOM300M User s Manual 201110 Y Y e o T y i o 18 AWG yellow green line Dip soldering ify Protection DE i 30 0 5 9 Figure 15 18 AWG Yellow green Line Note If KOM300M needs to perform a dielectric voltage withstand test in order to avoid test failure please disconnect the 18 AWG yellow green line to disable surge protection circuit which connects to surge grounding Disconnect 18 AWG yellow green line Figure 16 Disconnect 18 AWG Yellow green Line 6 LED Indicators Table 3 KOM300M LED Indicators see Coenen Power LEDs 15 KOM300M User s Manual 201110 10 100Base T X RJ45 port LEDs OFF 10M working state or no connection on Eee comecioninttepot a 100Base FX port LED 7 Management access Access the switch through the following two ways 7 1 Connected through Ethernet cable First connect any port of the device with the Ethernet port of a personal computer through an RJ45 cable Second open the Run window from the start menu then input telnet IP address Click OK to enter the Telnet interface The default IP addres
7. mna and Parsword that pou usa fee SICOM Used Hama aederer Patiwod Sove thes password in your passed Esi Figure 19 Access Web Interface 8 Product Models The specific configuration models of KOM300M are shown in below table Table 5 KOM300M Configuration Table O Mods O Deseripton Power 18 KOM300M User s Manual 201110 1 100Base FX port SM MM KOM300M 1S M 2T ports FC SC ST connector 12VDC 24VAC DC dual redundant power inputs 2 10 100Base T X RJ45 ports The optional accessories of KOM300M are shown in below table Table 6 KOM300M Optional Accessories odes scription DT BGAZ 01 Panel mounting kit DT FCZ RJ45 01 RJ45 dustproof shield 9 Basic Features and Specifications o Power Requirements Power input 12VDC 9 18VDC 24VAC DC 18 72VDC 18 50VAC Power terminal 5 pin 5 08mm spacing plug in terminal block Power consumption full load 2 6W MAX Physical Characteristics Housing Metal fanless Installation DIN Rail or Panel mounting Dimensions W X H XD 30mm Xx 115mm X 91 5mm Weight 0 3Kg e Environment Limits Operating Temperature 40 C to 85C Storage Temperature 40 C to 85 C Ambient Relative Humidity 5 to 95 non condensing o MTBF 462741hrs o Warranty 5 years 19 KOM300M User s Manual 201110 For more information about KYLAND products please visit our website http www kyland cn 20
8. s is 192 168 0 2 16 KOM300M User s Manual 201110 Type the name of a program folder document or Internet resource and Windows will open it For vou Open telnet 192 168 0 2 J Figure 17 Enter Telnet Third click OK and input a default user name admin and password 123 to enter the Telnet configuration interface see Figure 18 Type in a CLI command from Table 4 A Telnet 192 168 1 8 lser admin Password Welcome To Telnet Press RETURN to get started SWITCH gt Figure 18 Telnet Configuration Interface Table 4 CLI Command 17 KOM300M User s Manual 201110 SWITCH gt enable Enter management view Management View SWITCH show interface Show the IP address of current device Management View SWITCH show version Show hardware and software versions Management View SWITCH reboot Reboot Management View SWITCH load default Reload factory default settings Management View SWITCH config terminal Enter configuration view 7 2 Web interface First connect the Ethernet port on the PC to any RJ45 port on the device Second input the IP address of the current device in web browser default IP is 192 168 0 2 The Web interface access screen will appear as shown below in Figure 19 login with default user name admin and password 123 Enter Hetwork Paceword F This secure Web Site a 192 169 0 2 neque you to log on Pisaro ppe tha Leer Ha
9. sion Drawing for DIN Rail Mounting Unit mm dled 1 2 98 5 Figure 3 DIN Rail Mounting Dimension Drawing e Dimension Drawing for Panel Mounting Unit mm Figure 4 Panel Mounting Dimension Drawing Note The switch housing is a part of the heat dissipation system which becomes hot during operation Please be careful when handling the device during operation KOM300M User s Manual 201110 4 2 Mounting Steps O KOM300M DIN Rail Mounting The specific steps are as follows Step 1 Select the mounting position for KOM300M and ensure that there is adequate space Step 2 Insert the top of the DIN Rail into the slot of the DIN Rail connecting seat in the rear panel of KOM300M as seen in Figure 5 move the device in the direction of arrow 2 to put the whole Din Rail into the seat verify the KOM300M is firmly mounted on the DIN Rail as shown in Figure 5 DIN Rail Figure 5 DIN Rail Mounting Oo Remove KOM300M from DIN Rail The specific steps are as follows Step 1 Insert the screwdriver into the hole at the bottom of spring locking plate press the plate down to loosen the connection of DIN Rail and switch as shown in arrow 1 Step 2 Pull the KOM300M up in the direction of arrow 2 meanwhile remove the device from the DIN Rail along the direction of arrow 3 KOM300M User s Manual 201110 Figure 6 DIN Rail Dismounting Oo KOM300M Panel Mounting The specific steps are as follows Step 1 Selec
10. t the mounting position for KOM300M on the wall or in cabinet ensure that there is adequate space for the switch Step 2 Drill 4 holes on the selected position according to the panel mounting dimension drawings use a cross screwdriver to screw 4 cross slot screws M3 x 10 into holes Don t tighten the screws completely leave about 5mm of space between Step 3 Aim 4 mounting holes on KOM300M mounting plate at 4 fixed screws pass the screws through 4 holes with the diameter of 6 5mm 6 5 then slide down KOM300M as seen in arrow 2 finally screw 4 screws tightly Now the KOM300M should be firmly fixed to the wall or cabinet KOM300M User s Manual 201110 Screw Screw Figure 7 Panel Mounting O Remove KOM300M from wall or cabinet The specific steps are as follows Step 1 Use a screwdriver to loosen 4 screws move the device up to let screws into 4 holes with the diameter of 6 5mm 6 5 as seen in arrow 1 Step 2 Unscrew the screws from wall or cabinet remove the device from wall or cabinet Screw Figure 8 Panel Dismounting 5 Cable Connection 10 KOM300M User s Manual 201110 5 1 10 100Base T X Ethernet port 10 100Base T X Ethernet RJ45 port can be connected to terminal equipment and network devices with straight through cables or crossover cables RJ45 connectors must be equipped at both ends of cable O Pin definition of 10 100Base T X RJ45 port Pin number of 10 100Base T X RJ45 port is shown
Download Pdf Manuals
Related Search