OWNER`S MANUAL - Webstaurant Store
Contents
1. 76 2 cm x 47 9 cm x 87 9 cm 76 2 cm x 47 9 cm x 87 9 cm 76 2 cm x 47 9 cm x 87 9 cm Product Weight 108 Ibs 49 2 kg 108 Ibs 49 2 kg 108 Ibs 49 2 kg Initial Heat Up Time d it minutes 4 5 2 minutes 4 5 2 minutes Heat Up Time Base Pellet 12 seconds 12 seconds 12 seconds All Indicator Lights LED LED LED Heat up to 20 Camduction Bases at one time in 4 5 2 minutes based on voltage supply from start up before each meal service Fvery 12 seconds based on voltage supply WHEN being removed and replaced during meal service IV Set Up and Operating Instructions 1 Set unit backside down and screw in each leg No tools required 2 Prior to use Set charger on a stable level surface and adjust legs by rotating the foot of the legs until all four are making contact with surface 3 On Single Phase models Plug into properly grounded outlet with specified power supply Voltage over 250 Vac will cause the charger to error 4 On Three Phase models A qualified technician must connect power to the charger not exceeding the stated value on the data plate and must include a ground All local codes and or regulations must be followed when supplying power to the charger Voltage over 250 Vac will cause the charger to error 5 Charger MUST be EMPTY before turning ON EMPTY charger AFTER each meal service NOTE Charger will NOT TURN ON if there are Pellets or Bases pre loaded and connected in compartments 6 Turn pow2. CERETI Y A o U S Patent 8 263 906 B2 Service in the USA or CANADA must be performed by a Cambro Authorized Camduction Base covered by Service Technician Please refer to Warranty Section for coverage and U S Patent D630 897 S and details For all Warranty Service please call 1 800 854 7631 ext 4118 or arts ie Salty D635 394 S 1 714 848 1555 Service on Out of Warranty repairs MUST be performed by a DIN GI Camduction Pellet covered by Qualified Technician or Electrician oe EP CNT Zs U S Patent D628 854 S IL Safety Instructions and Warnings IMPORTANT Please read ALL instructions prior to first use Follow all warnings and instructions marked on charger unit and in this manual Use only CAMBRO authorized replacement parts For service please contact Cambro at 800 854 7631 x4118 or 1 714 848 1555 Units under warranty must be serviced by a Cambro Authorized Service Agent ONLY to remain under warranty Please refer to Warranty section in the back of user manual for coverage details WARNING ELECTRIC SHOCK HAZARD Use only supplied cord plug AND proper power source on Single Phase Units Use 10 gauge wires for input power on all Three Phase Units Must be installed by a qualified technician and according to local electrical requirements e WARNING Do NOT use if power cord is frayed or damaged or plug blades are missing bent or broken e WARNING USE only power supply source as indicated on label on back of unit e WARNING Connect into
3. properly grounded power source ONLY Plug single phase models directly into matching locking receptacle Never use an adapter e CAUTION Do NOT use in wet or damp conditions 4 10 2 cm e WARNING NEVER place wet Camduction Pellet or Base in compartment Close Up of single phase model CAMBRO TRUSTED FOR GENERATIONS www cambro com Safety Instructions and Warnings Con t e WARNING NEVER multi charge re heat HOT Camduction Pellets or Bases that have been removed from compartment ALWAYS charge room temperature Camduction Pellets or Bases ONLY Re heating hot or warm Pellets or Bases may result in damage to Pellet Base and or Charger e CAUTION When using a mobile cart to hold the Camduction Charger the cart should only be moved for cleaning purposes and not used for transporting the Charger AN WARNING ELECTRIC SHOCK HAZARD Keep electrical parts dry NEVER use in wet or damp locations e WARNING NEVER submerge charger in water or spray water on or near unit e WARNING Always UNPLUG or disconnect unit from power source prior to cleaning or service ALL power MUST be removed and the charger unplugged or disconnected before cleaning the station areas e WARNING NEVER steam or pressure clean or hose down cabinet May cause electrical shock to operator NEVER use corrosive cleaners to clean cabinet NEVER use a wet cloth to clean shelves or charging stations unless ALL power has been removed and the char
4. OWNER S CAMBRO CAMDUCTION MANUAL COMPLETE HEAT CHARGER This owner s manual applies to all of the following Table of Contents product models Introduction ccccssessecceessessessssssececssessessscssessessesstsstesseseeseeesneasen Model MDSCDCP9 Special Order Only ll Safety Instructions and Warnings ceeeeescesseeeeseeeees 1 2 For use with CAMBRO Camduction Pellet MDSCDP9 Ill Product Specifications c sccecscssssessssesssesssessseessseesseessseessee 2 Note Pellet Requires Underliner MDSCDLS IV Set Up and Operating Instruction 3 Model MDSCDCBI amp MDSCDC9IX1 Single Phase V Cleaning and Maintenance 3 4 For use with CAMBRO Camduction Base MDSCDB9 VI Product Drawings ssis 5 Model MDSCDC9X3 Three Phase Vil Wiring Diagram and Electrical Components c cee 6 For use with CAMBRO Camduction Base MDSCDB9 VIII Troubleshooting Guide 7 ege mg A Replacement Falls cronin A Cambro Warranty and Product ab 8 Introduction Congratulations on the purchase of your new Cambro Camduction Complete Heat Charger Here is a step by step guide for proper operation and maintenance If you have any questions please contact your Cambro Sales Representative visit the Web site at www cambro com or contact Customer Camduction Charger covered by Service Department at 1 800 833 3003 or 1 714 848 1555 All Warranty IA i i A A t AT Co 2 mmm Lem Leem r Lem r ay a ar ar wem E H um 1 mg
5. Y OF CAMBRO MANUFACTURING WITH RESPECT TO THE PRODUCT S NOTE Cambro Camduction Base and Pellet have a two 2 year pro rated warranty from the date of shipment from authorized Cambro distribution locations RETURN POLICY Cambro Manufacturing products cannot be returned without prior written factory authorization RMA The restocking charge is 15 plus any costs required to recondition the equipment No returns accepted after 90 days from date of invoice Electrical components returned are subject to inspection prior to credit being issued Electrical components which have been installed by an operator or non approved service agent are not returnable for credit R 0 Telephone 714 848 1555 Toll Free 800 854 7631 Customer Service 800 833 3003 CAM Cambro Manufacturing Company 5801 Skylab Road Huntington Beach California 92647 2056 TRUSTED FOR GENERATIONS UMCDC1011 REN E Printed in USA 09 14 UMCD1011 REV E
6. all not be made by children without supervision 1 Use clean cloth to wipe charger compartment shelves 2 Clean outside of cabinet with a nonabrasive cloth dampened with a solution of warm water and mild soap or detergent Or use a commercial stainless steel cleaner following manufacturer s directions See Safety Instructions and Warnings for complete details 3 To remove and clean the 20 compartment shelving unit follow these steps a Unscrew and remove the 4 slotted screws from front of Charger see Fig A b Carefully pull out and remove compartment shelving unit from Charger c Clean unit with a clean cloth d Slide unit back into Charger and secure with 4 slotted screws 4 Before plugging in charger after cleaning ensure power cord is not frayed damaged and plug blades are not bent or broken or missing Replace cord plug immediately if damaged with approved Cambro replacement parts only Call for service 5 The Camduction Base MDSCDBY is made of two separate parts that are factory assembled a Base Pellet and a Base Rim If necessary these may be disassembled and reassembled for cleaning by following the directions on page 4 6 Place Pellet or Base with socket pins facing up for cleaning through dishwasher Failure to do so may result in bent or damaged pins that will not connect properly into power pin socket Figure A View of slotted screw V Cleaning and Maintenance Con t ch r gt t Step 1 Fi
7. ambro com for a complete list of replacement parts The model number of the Cambro Camduction Complete Heat Charger is required to determine the correct replacement part The model number and serial number can be found on the side adjacent to the electrical cord of the unit TO ORDER REPLACEMENT PARTS e Call Cambro Customer Service at 1 800 833 3003 or 1 714 848 1555 e Fax your order to 714 842 3430 e Call your local Cambro Representative or Distributor X Cambro Warranty And Product Liability LIMITED ORIGINAL COMMERCIAL ELECTRICAL EQUIPMENT WARRANTY FOR CAMDUCTION COMPLETE HEAT CHARGER ONLY Cambro Manufacturing warrants its new product s to be free from defects in material and workmanship for a period of one 1 year from the date of shipment from authorized CAMBRO distribution locations This Warranty is subject to the following conditions and limitations 1 This warranty is limited to product s sold by Cambro Manufacturing to the original user in the continental United States and Canada For International Warranty Claims contact your local Cambro Representative 2 The Liability of Cambro Manufacturing is limited to the repair or replacement of any part found to be defective Parts and labor required for preventive maintenance or cleaning are not covered under this warranty 3 Cambro Manufacturing will bear normal charges incurred in the repair or replacement of a warranted piece of equipment within 50 miles 80 kil
8. board Bottom Board 3 Compartments are connected to the bottom board Thermostat Thermostat 60T21 X 13779 A 60121 X 13779 A 8 76 A 1 LED 20 2 Orn eee PELLET 20 3 0000 32 1 4 CAMO006 CAMO006 3 E LED 1 1 won E 3 8 7 6 5 3 PELLET 10 97 91010 al LED 10 ooo oi Breaker AK2 B0 24 630 221 D LINE LOAD Lug View Sticker on the Bottom Connect to Chassis VIII Troubleshooting Guide Possible Causes Possible Solutions 1 Charger is ON Top indicator light is GREEN Bases or Pellets are loaded in Charger Compartment lights are flashing RED amp GREEN Charger is ON and EMPTY Top indicator light does not turn GREEN Power source and cord plug are verified OK Power switch is ON Top indicator light does not turn GREEN Charger is ON Top indicator light is GREEN Compartment light remains OFF when Base or Pellet is inserted into compartment power pin socket 5 Compartment LED light is GREEN but Base or Pellet is COLD 6 Base or Pellet heats up but compartment LED light LED light not connected to board does not turn RED or GREEN e Defective LED light 7 Smoke or fumes coming from Bases or Pellet s loaded in compartments and charging e Bases or Pellets were pre loaded and connected into the compartment power pin sockets before turning charger ON No power source Power cord not properly connected to live power source Power cord or plug damaged Trip
9. er switch ON Main power indicator light on top front will turn GREEN Each compartment indicator light will flash RED then GREEN and then OFF indicating compartments are ready to load 7 lf a compartment light is flashing RED and GREEN refer to Trouble Shooting Guide Section 1 page 7 8 Slide ROOM TEMPERATURE ONLY Pellets or Bases into compartments and connect with power pin socket Compartment light will turn RED then GREEN in 4 5 2 minutes based on voltage supply indicating Pellet or Base is HOT and ready to use 9 During meal service replace charged Pellets or Bases with room temperature ONLY Pellets or Bases for fast continuous service 10 If Pellet or Base FAILS to heat up refer to the Trouble Shooting Guide Section 1 page 7 11 POWER SAVING MODE Charger is divided into 3 charging zones Each zone supports 6 7 compartments Any zone not in use for 45 minutes will go into POWER SAVING MODE All compartment lights in that zone will go OFF indicating NO power to pin sockets To use ALL ZONES turn charger OFF REMOVE ALL bases turn charger ON and go back to instruction 6 DO NOT slide HOT Pellets or Bases back into compartments 12 After each completed meal service REMOVE all Pellets or Bases and turn charger OFF V Cleaning and Maintenance AN WARNING ELECTRIC SHOCK HAZARD Turn off and unplug or disconnect power to charger before performing cleaning or maintenance service Cleaning and maintenance sh
10. ger is unplugged or disconnected We recommend stainless steel cleaner for stainless steel surfaces DO NOT place anything on top of charger NOTICE Pellets and bases must never be connected into compartment power pin sockets when charger is first turned on or after charger is turned back on after POWER SAVING MODE Do not store pellets or bases in charger when not in use NOTICE This appliance is NOT intended for use by children under the age of 8 or persons with reduced physical sensory or mental capabilities OR with lack of experience and knowledge concerning the use of the application NOTICE Children should be supervised to ensure that they do not play with the appliance NOTICE Cleaning and user maintenance shall NOT be made by children without supervision Ill Product Specifications Single Phase Single Phase Three Phase Charger Models MDSCDCP9 Special Order Only MDSCDCB9 MDSCDC9X1 MDSCDC9X3 Heats Camduction Pellet Only Camduction Base Camduction Base Capacity 20 Pellets 20 Bases 20 Bases Voltage Phase 208 240 VAC Single Phase 208 240 VAC Single Phase 208 240 VAC Three Phase L L Amps 24 9 MAX 24 9 MAX 18 12 Hz 50 60 50 60 50 60 Plug NEMA L6 30P NEMA L6 30P US CAN or N A Configuration 32 6h 200 250 Euro Rnd Plug INT L Cord Length 6 feet 183 cm 6 feet 183 cm N A Product 30 W x 187 s D x 34 s H 30 W x 187 s D x 34 s H 30 W x 18 7 s D x 34 s H Dimensions
11. ometers of an authorized service agency Time and travel charges in excess of 50 miles 80 kilometers will be the responsibility of the person or firm requesting the service All labor to repair and or service the warranted unit s shall be performed during regular working hours Overtime premium will be charged to the buyer and is NOT covered by this warranty 4 Charges incurred by delays or operating restrictions that hinder the service technician s ability to access or perform service to equipment in question are NOT covered by this warranty This includes Institutional Correctional Military and Marine facilities 5 Cambro Manufacturing will bear no responsibility or liability for any product s which have been mishandled abused misapplied misused Subjected to harsh chemical action damaged by flood fire or other acts of nature field modified by unauthorized personnel or which have altered or missing serial numbers 6 Cambro Manufacturing does not recommend or authorize the use of any product s in a non commercial application including but not limited to residential use The use or installation of any product s in non commercial applications renders all warranties express or implied including the warranties of MERCHANTABILITY and FITNESS FOR A PARTICULAR PURPOSE null and void including any responsibility for damage costs and legal actions resulting from use or installation of product s in any noncommercial setting 7 Adjustmen
12. ped breaker switch Defective power switch Base or Pellet is NOT properly inserted into power pin socket Compartment power pin socket is NOT working Charger has switched one or more charging zones to POWER SAVING MODE after 45 minutes of NON USE and has automatically turned OFF power to SOME or ALL of the compartment power pin sockets LED light is not working Base or Pellet NOT properly inserted into compartment power pin socket Base or Pellet NOT working properly Compartment power pin socket Is not working e Hot Bases or Pellets were loaded BACK into compartments without cooling to room temperature between uses and have RE CHARGED and OVERHEATED e Bent or damaged pins are causing ARCING or HIGH HEAT at the pins Turn Charger OFF Disconnect Base or Pellet from each compartment power pin socket Turn charger back ON Wait for top indicator light to turn GREEN before loading Slide room temperature Bases or Pellets into compartments ONLY after power is turned on Verify power to the receptacle Ensure charger is completely plugged into the proper specified live power source Replace power cord Call for service Reset building outlet breaker switch Reset Charger turn OFF then back ON Replace power switch Call for service Slide Base or Pellet into same compartment socket pin again Try same Base or Pellet in another compartment Turn Charger OFF Disconnect Base or Pellet from each compa
13. rmly grasp the Base Rim on both sides with Step 2 Pull both sides of the Base Rim out and push the the arrow on the Base Pellet facing forward Base Pellet up from the bottom until it snaps out of the Base Rim Step 3 To reassemble align the arrow on the top of the Base Pellet with the notch line on the inside of of a table Holding the Base Pellet down with your the Base Rim left hand pull the Base Rim out with your right hand in three places as shown above until the Base Pellet Snaps securely into place Step 5 Turn the Base upside down to verify that the Base Pellet and Base Rim are assembled together correctly as shown above VI Product Drawings Pellet Charger for Base Charger for VW KI L Eu WW WW WW WW WW i i L i 1 i Pellet Charger Base Charger Base Insertion Side View Pellet Insertion Top View VII Wiring Diagram and Electrical Components Camduction wiring 208 240VAC Single Phase For the MDSCDC9X1 Camduction Three Phase 208 240v Delta wiring Line to Line For MDSCDC9X3 Berocp BREAKER Camduction Three Phase 208Y Wye wiring Line to Line For MDSCDC9X3 Sub Panel POOLE 3 each Cevantio Bee wer e J Camduction Charger Pellet Base Connector Pellet Base Power Cord NEMA L6 30P Camduction Board Zone Connection Top Board 1 Compartments are connected to the top board Middle Board 2 Compartments are connected to the middle
14. rtment power pin socket Turn charger back ON Wait for top indicator light to turn GREEN before loading dry room temperature Bases or Pellets into compartments If a light or lights remain OFF LED light s could be defective and need to be replaced OR a compartment power pin socket s could be defective and needs to be replaced Call for service Slide Base or Pellet into same compartment socket pin again Try same Base or Pellet in another compartment If it heats up properly then replace power pin socket in the malfunctioning compartment Call for service If Base or Pellet does not heat up it s defective and must be replaced Wire light connection disconnected Call for service Replace LED light Call for service Carefully remove Base or Pellet and replace with dry room temperature Base or Pellet Replace Bases or Pellets if they do not perform correctly or have visible damage Damaged Bases or Pellets may cause damage to the Charger Do not use Bases or Pellets with damaged pins Inspect all pins and if damaged replace Base or Pellet NOTE There are no Owner Operator serviceable parts located inside the Camduction Complete Heat Charger Please contact Cambro for ALL service calls ALL electrical adjustments or electrical part replacements MUST BE completed by an Authorized Cambro Service Technician For service in USA or CANADA please call 1 800 833 3003 ext 4118 IX Replacement Parts Please visit www c
15. ts such as calibrations leveling tightening of fasteners or utility connections normally associated with the original installation are the responsibility of the dealer or installer and not that of Cambro Manufacturing Improper installation includes but is not limited to use of inadequate electrical wiring and or insufficient or improper voltage 8 Replacement part s which are replaced in the field by CAMBRO authorized service technicians ONLY will be warranted for the duration of the equipment warranty or 90 days effective from date of installation whichever is greater This warranty is for part s cost only and does not include freight or labor charges 9 This states the exclusive remedy against Cambro Manufacturing relating to the product s whether in contract or in tort or under any other legal theory and whether arising out of warranties representations instructions installations or defects from any cause Cambro Manufacturing shall not be liable under any legal theory for loss of use revenue or profit or for substitute use of or performance or for incidental indirect or special or consequential damages or for any other loss or cost of a similar type 10 THIS WARRANTY AND THE REPRESENTATIONS AND TERMS SET FORTH HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES AND LIABILITIES INCLUDING BUT NOT LIMITED TO OTHER WARRANTIES EXPRESS OR IMPLIED OF MERCHANTABILITY AND FITNESS FOR PARTICULAR USE AND CONSTITUTES THE ONLY WARRANT
Download Pdf Manuals
Related Search