user`s guide to - MikroElektronika
Contents
1. 5V 3 3V or 5V DC depends on MCU power supply power consumption min O 6uA standby mode CONSUMPTION 3mA write mode at 100kHz board dimensions 45 34 x 23 88 mm 1 78 x 0 94 weight 0 02 Ibs 1 Connecting with development system Figure 1 1 EEPROM connected to development system Figure 1 2 Connecting EEPROM EEPROM is designed for connection with 2x5 male headers on development system port s via 2x5 female header accessory board Every pin on 2x5 female header is marked so for proper orientation just compare marks between accessory board and development system 2 DIP switch settings PS sl T YES oM In order to connect to different development system it is necessary to make settings on DIP switch Sw1 Every pin on DIP switch SW1 is connected to different pin of 2x5 female header In table 1 is given list which switch on DIP switch SW1 should be turned ON for Figure 2 1 DIP switch different development system with 2x5 female header Table 1 Development system Turn ON switch number Pin on female 2x5 header LONE Page 7 VCC VCC O 3 PO P1 P1 VCC m 2 VCCI R3 R2 Ara WPT 4K7 AKT SCLI SCL 2K2 VCC ow D gt 3 SDAJ 1 SDAI VCC N D1 M M6 __ 100nF Figure 3 1 Connection schematic 4 Dimensions 16 36mm 0 62. merchantability or fitness for a particular purpose MikroElektronika shall assume no responsibility or liability for any errors omissions and inaccuracies that may appear in this manual In no event shall Mik roElektronika its directors officers employees or distributors be liable for any indirect specific incidental or consequential damages including damages for loss of business profits and business information business interruption or any other pecuniary loss arising out of the use of this manual or product even if MikroElektronika has been advised of the possibility of such damages MikroElektronika reserves the right to change information contained in this manual at any time without prior notice if necessary HIGH RISK ACTIVITIES The products of MikroElektronika are not fault tolerant nor designed manufactured or intended for use or resale as on line control equipment in hazardous environments requiring fail safe performance such as in the operation of nuclear facilities aircraft navigation or communication systems air traffic control di rect life support machines or weapons systems in which the failure of Software could lead directly to death personal injury or severe physical or environmental damage High Risk Activities MikroElektronika and its suppliers specifically disclaim any expressed or implied warranty of fitness for High Risk Activities TRADEMARKS The Mikroelektronika name and logo the Mikroelektronika l
3. 4 45 34mm 1 78 PROM HWREV 1 10 Figure 4 1 Dimensions 23 88mm 0 94 UU 10 DISCLAIMER All the products owned by MikroElektronika are protected by copyright law and international copyright treaty Therefore this manual is to be treated as any other copyright material No part of this manual including product and software described herein may be reproduced stored in a retrieval system translated or transmitted in any form or by any means without the prior written permission of MikroElektronika The manual PDF edition can be printed for private or local use but not for distribution Any modification of this manual is prohibited MikroElektronika provides this manual as is without warranty of any kind either expressed or implied including but not limited to the implied warranties or conditions of
4. Expand development system capabilities by R adding 8K EEPROM memory accessory board DEVELOPMENT TOOLS COMPILERS BOOKS 0005 00 CUSTOMERS want to express my thanks to you for being interested our products and for having confidence Mikroelektronika The primary aim of our company is to design and produce high quality electronic products and to constantly improve the performance thereof in order to better suit your needs Nebojsa Matic General Manager The Microchip Atmel NXP and CYPRESS name logo and products names are trademarks of Microchip Atmel NXP and CYPRESS Inc in the U S A and other countries 5 Introduction to EEPROM Key features System Specification 1 Connecting with development system 2 DIP switch settings 3 Schematic 4 Dimensions Page 3 ON MA UN fH A n fA Intr oducti on to e T Accessory board is designed for usage with various development systems and other MCU device with 2x5 header EEPROM accessory board is designed to add 8K of EEPROM memory to microcontroller via serial 12 communication Key features Pads with female 2x5 header back side of the board DIP switch for pin selection Power indication LED EEPROM chip 24 08 5 Um w i 5 System Specification
5. ogo mikroC mikroC PRO mikroBasic mikroBasic PRO mikroPascal mikroPascal PRO AVRflash PICflash dsPICprog 18FJprog PSOCprog AVRprog 8051prog ARMflash EasyPIC5 EasyPIC6 BigPIC5 BigPIC6 dsPIC PRO4 Easy8051B EasyARM EasyAVR5 EasyAVR6 BigAVR2 EasydsPIC4A EasyPSoC4 EasyAVR Stamp LV18FJ LV24 33A LV32MX PIC32MX4 MultiMedia Board PICPLC16 PICPLC8 PICPLC4 SmartGSM GPRS UNI DS are trademarks of Mikroelektronika All other trademarks mentioned herein are property of their respective companies All other product and corporate names appearing in this manual may or may be registered trademarks or copyrights of their respective companies and are only used for identification or explanation and to the owners benefit with no intent to infringe Mikroelektronika 2011 All Rights Reserved v1 10 If you want to learn more about our products please visit our website at www mikroe com If you are experiencing some problems with any of our products or just need additional information please place your ticket at www mikroe com en support If you have any questions comments or business proposals do not hesitate to contact us at office mikroe com
Download Pdf Manuals
Related Search