User Manual
Contents
1. Choosing a site for the base unit The base unit should be placed on a level surface in a position where e The mains adapter plug will reach a 230 V AC switched mains supply socket never try to lengthen the mains power cable e The telephone cable will reach your telephone line socket or extension socket e tis not close to another telephone this can cause radio interference e It is not close to a sink bath or shower or anywhere else where it might get wet e It is not close to other electrical equipment fridges washing machines microwave ovens TVs fluorescent lights etc User Manual Installation 1 Choose a suitable site for the base unit Make sure it is not near to another telephone nor to other electrical equipment 2 Plug the mains power lead and the telephone line cord into the bottom of the base unit Plug the mains adapter into a 230 V AC 50 Hz mains socket with the switch on the socket set to OFF 3 Switch on mains power at the Note The illustration of adaptor socket may vary from country to country 4 Fit the batteries in the handset Insert the batteries cell following the batteries polarity indication Push the latch inwards and then slide the cover until it clicks firmly into position 5 Plug the USB dongle into your PC USB socket Note Your model 101 is supplied with the handset and USB dongle already registered to the base unit you shouldn t need to register them Ref2. To Set Flash Time You can change flash time to short or long 1 Select lt Dial Settings gt under Base Settings mode 2 Select lt Flash Time gt under Dial Settings 3 Press Left S key and Scrolling button to change Flash Time to Long or Short 4 Press Left 5 key to confirm To Set Auto Pause When you call a number with a pause the phone waits a few seconds before transmitting the next digits in the dialing sequence This is useful when you have to dial a number for access to an outside line or for going into a voicemail system You are allowed to set one number in Auto Pause 1 Select lt Dial Settings gt under Base Settings mode 2 Select lt Auto Pause gt under Dial Settings 3 Press Left key then key in PIN default 0000 4 Press Left D key then key in the number you want to set auto pause 5 Press Left D key to confirm To Set Dial Mode You can change dial mode to TONE or PULSE dialing 1 Select lt Dial Settings gt under Base Settings mode 2 Select lt Dial Mode gt under Dial Settings 3 Press Left D key and Scrolling W button to change dial mode as TONE or PULSE 4 Press Left 5 key to confirm 23 User Manual Call Barring Function Call barring enables you to restrict or bar certain types of calls from your phone To Set Call Barring Number 1 Select lt Call Barring gt under Base Settings mode 2 Select lt Barring Number gt under Call Barring 3 Press Left SI key th
3. Press Left key to confirm then Scrolling button to the location ExternalRing InternalRing 3 Press Left key and Scrolling button to choose the ring melody you want to set 4 Then press Left 5 key to confirm the choice To Set Key Tone On Off 20 User Manual Each time you press a key on your handset you hear a tone You can turn this off if needed 1 Select lt Ringer Set under Handset Set mode 2 Press Left key to confirm then Scrolling button to the location Key Beep a an 3 Press Left D key and Scrolling 7 button to set the key beep ON OFF 4 Press Left 5 key to confirm Auto Talk Function Normally you need to press the Call QU button to answer an incoming call But with AUTOTALK function turned on when your handset is ringing for an incoming call you can answer the call by simply lifting the handset from the base unit without pressing the Call Q button To Set Auto Talk Function ON OFF 1 Select lt Auto talk gt under Handset Set mode 2 Press Left ES key and Scrolling button to set Auto talk ON OFF 3 Then press Left ES key to confirm Note If you have turned Auto talk on do not press the Call QA button after you ve answered a call by lifting the handset otherwise you ll disconnect the call To Set Handset Name 1 Select lt Handset Name gt under Handset Set mode 2 Press Left key to confirm 3 Key in your chosen name 4 Then press Left 5 key
4. D key to confirm and key in New PIN Press Left S key then key in New PIN again Press Left D key to confirm Default Settings 1 Select lt Default settings gt under Base Settings mode Press Left key and key in the current PIN number Press Left key to confirm you will hear a beep then all features will return to their default settings The following default settings are for you reference Reset Flash time to Long Delete call barring number Reset master pin number to 0000 Reset ringer melody and volume Dial mode reset to Tone Remove Auto Pause number Remove LCR if available Registration Your model 101 is supplied with the handset and USB dongle already registered to the base unit you shouldn t need to register them But if you ve bought extra 25 User Manual handset you ll need to register each one to your original base unit Maximum 3 handsets can be registered to one base To Enter Registration Mode 1 Select Settings under menu mode 2 Press Left D key select Registration and the display shows Select Base Base Sub and De register To register a handset 1 Press and hold the Handset locator button on the base unit for a while until you hear beep sound twice continuously 2 Select Base Sub under Registration mode 3 Press Left key again The display shows BASE 1 BASE 2 BASE 3 BASE 4 4 Press Scrolling button to scroll through the base and pres
5. Left 5 key again the display shows Received Calls Dialed calls Missed Calls and Notifications Select the calls type you wish to check by Scrolling button then press Left key the display shows these calls numbers 7 Select one number then press left ES key and Scrolling 4 button to the location Show Details Press Left D key then the display shows the details of the call including the call number and the date and time the call is received dialed or missed To Save Call 1 2 O See steps 1 3 above A Select one number then press Left key and goes to the location Save Press Left key and key in the name Press Left S key to confirm and key in the number Press Left key to store it To Delete Call Records 1 2 See steps 1 3 above Select one number then press Left a key and Scrolling button to the location Delete Current or Delete All Press Left ES key the display shows Delete Press Left key to confirm 18 User Manual To Check Notification Alert You must subscribe to Notification service from your service provider to use this feature 1 Select Call list under menu mode Press Left S key again the display shows Received Calls Dialed calls Missed Calls and Notifications Press Scrolling X button to select Notifications then press Left key the display shows the alert To Make SkypeOut Call from Call List 1 2 Select Call list
6. To Toggle between Skype call and PSTN call I When you already engaged on an ongoing call if another Skype call is received press Right LZ key to enter option menu a a Then press Scrolling 7 button to select Hook up and press Left E key Press Right LZ key to enter option menu again Press Scrolling button to select Switch Press Left S key to toggle the phone connection If you want to hook down the Skype call press Right key to enter option and Scrolling button to select Hook down then press Left key To Make a Skype Conference Call 1 When you already engaged on an ongoing call if another Skype call is received press Right L key to enter option menu ai ny Then press Scrolling 7 button to select Hook up and press Left A key Press Right 7 key to enter option menu again 14 User Manual a 4 Press Scrolling button to select Conference Call 5 Press Left key to connect the three parties together s Note You cannot host a conference call by yourself but can be invited to participate in a conference call opened by the other Skype users Conference Calling You need to register with your fixed line network operator for conference calling service It is dependant on service availability and subscription To Make an Ordinary Conference Call 1 Connect the first party 2 Press INT lt key and the first party is put on hold 3 Dial second party s phone n
7. Try moving the handset closer to the base unit Try a different position for the base unit perhaps higher or further from other electrical equipment The phone does not ring 33 User Manual Check that the base units mains power adapter is plugged in and power is switched on The base unit needs mains power for normal operation of the phone not just charging the batteries Make sure you are using the telephone line cable that was supplied with your model 101 Other telephone line cables might not work Check that you have set the ringer volume to off See the user manual for more information Check that the total REN value of all equipment connected to your telephone line is no more than 3 Disconnect one or more telephones and see whether that helps The base does not ring Check that the base power is ON and the base ringer is set ON Check that the line cord is correctly fitted and undamaged The CHARGE light on the base unit does not come on Check the handset is properly stationed Check the connections between the base unit and mains power socket Clean the batteries charging contacts with a dry cloth When I press the CALL button I hear a loud noise The strange noise is caused by interference Disconnect the mains power lead from the back of the base unit and then wait for 30 seconds before reconnecting it There is beep sound while am on a call You may be going out of range of the base unit Move c
8. to confirm To change Handset Name 1 Select lt Handset Name gt under Handset Set mode 21 User Manual 2 Press Left key to confirm the display shows the current name 3 Press and hold the Right key to clear the old name then key in the new name 4 Press Left ES key to confirm to the change To Set Language You can select the language from the menu up to your preference 1 Select lt panguagre under agua Set mode 2 Press Left gt i key and Scrolling E button to choose the language you prefer 3 Then press Left ES key to confirm the setting To Lock Unlock the Keypad e Press Left S key and button consecutively to lock unlock the keypad To Enter Base Settings Mode 1 Select Settings under menu mode 2 Press left S key select Base Settings and the display shows Ringer Settings Dial Settings Call Barring LCR PIN and Default Settings To Set Base Volume 0 4 volume level 1 Select lt Ringer Settings gt under Base Settings mode 2 Select mangar Volume gt under e Settings 3 Press Left gt key and Scrolling 4 button to set the volume you like 4 Press Left l key to confirm To Set Base Melody 1 9 melody 1 Select lt Ringer Settings gt under Base Settings mode 2 Select anger Melody gt uno Ringer Settings 3 Press Left gt key Scrolling button to set the melody you prefer 99 User Manual 4 Press Left key to confirm
9. user manual will help you get the most out of handling the different calls and learning how to navigate the handset menu USB Dongle Minimum System Requirements Before continuing any further with the installation please make sure you have the minimum system requirements as specified here s Broadband Service z PC with the following minimum specifications Pentium 400Mhz processor CPU or above PC running Microsoft Windows 2000 or XP Available USB Port USB2 0 or USB1 1 Skype version 1 2 or higher visit www skype com 128Mb RAM 256Mb RAM recommended 10Mb Hard Disk space CD drive for software Driver a User Manual Package Contents The contents of your product should contain the following items For any missing items please contact your dealer immediately USB Dongle Power adapter AC 7 5V 350mA Telephone Cable RJ 11 a Lrer anual User Manual 49 Installation CD _ Battery Cell 1 2 x 2V 750 mAh Note To make Internet calls your PC must be turned on and the Skype software must be activated User Manual Physical Details The Handset and Base Unit Left Key Press to enter menu and sub menu mode Press to confirm selection With the key to lock or unlock the keypad Press during a call to mute the mouthpiece Call Recall Key Press to begin and answer a telephone call You can activate Recall function if your phone is connected to a
10. 2 Press Left 5 key the display shows these calls 3 Select the telephone number you want to call then press the Call WA UA key to make call To Redial a Call e In standby mode plese and hold the Call QA a key to enter the dial list and press the Scrolling a button to scroll through the number you want to dial then press the Call QA key to redial Earpiece Volume e During a call you just press Scrolling button up down to adjust the volume of the earpiece 0 9 level To Mute the Mouthpiece o 1 During a call press Left fall key once to mute the mouthpiece 2 While the mouthpiece is muted you cannot press any number key to send digits down the line 3 Press Left 5 key again to get back to the Call 13 User Manual Call Waiting The UBiQUiO model 101 has a Call Waiting feature that works with Caller ID service from your telephone service operator When you re engaged on a PSTN ongoing call if you receive a second Skype call your phone will use a call waiting signal to let you know another call is ringing in This way you can switch between Skype and PSTN callers hook down Skype call or even make Skype conference call together To Hook down up the Second Call Skype Call 1 When you already engaged on an ongoing call if another Skype call is received press Right L key to enter option menu Then press Scrolling 7 button to select Hook up Hook down Press Left S key to confirm
11. D key then key in the date 3 Press Left key to save Skype Function To Make Skype Call from Contact List 1 Select Skype under menu mode 2 Select lt Contact List gt under Skype mode 3 Press Left D key then the display shows the Skype online user list 4 Press Scrolling 7 button to select the record you wish to call 5 Press Call Ox key to place a Skype call 28 User Manual Note Press shortcut key Up button in the scrollbar to enter the Skype contact list directly or use above steps Quick Search This function enables you to speed search the list by inputting the initial letter or number of the list you look for For example if you would like to search a user namely Linda in your contact list press 5 key and then J KL j k15 box will be displayed on the screen Press 5 key continuously until you select L Then it would perform search for you To Make Skype Call from Skype Calllogs k 2 Select Skype under menu mode Select lt Skype Calllogs gt under Skype mode Press Left 5S key then the display shows the Skype Calllogs indicating the Online Status of these users Received Skype call marked with 4wWY Dialed call marked with and Miss call marked with 8 Press Scrolling button to select the record you wish to call Press Call OA key to place a Skype call To Set User Status 1 2 Select Skype under menu mode
12. PABX or if you use Select Services Press to transfer an outside call to another phone Scrolling Button Press during programming to move through the menu Press during a call to change the volume in the earpiece Speakerphone Key Press to turn the speakerphone ON OFF Note Before you can use the handset to make calls for the first time you will need to fit and fully charge the batteries for 15 hours Right Key Press to enter phonebook menu Press during programming to go back to the previous option Press to clear digits from the display End On Off Key Press to end a telephone call Press and hold 2 3 seconds to switch the handset on off INT Key Press to make an intercom call Gif you have more than one handset In Use Light The IN USE light comes on when you have a connection to the telephone line Charge Light The CHARGE light comes on when the handset s batteries are being charged Handset Locator Button Press this to make the handset ring if you cannot remember where you put it press it again to stop the handset ringing The USB dongle User Manual LED Light Registration Indicator User Manual What the symbols mean Ta Batteries Charge Level Whenever this shows nearly empty m put the handset on the base unit to charge the batteries While the batteries are being charged the level shown will keep changing Sl Mute Your handset s
13. Select lt User Status gt under Skype mode Press Left key then the display shows the selection status Press Scrolling button to select the status you wish to set Press Left Ss key to save 29 User Manual Resetting the system If you have set a PIN and forgotten it you need to reset the system The PIN will be reset to 0000 If you reset the system you will lose all stored information including numbers in memory and all features will return to their default settings You need to register the handset to the base unit again While you are resetting the system you should disconnect the telephone line cord from the back of the base unit so you won t be interrupted by incoming calls To reset the system without the PIN 1 Disconnect the power lead from the back of the base unit 2 Press and hold the HANDSET LOCATOR button in the base unit at the same time connect the power lead into the back of base unit Release the LOCATOR buiton after you hear beep sound for five times The IN USE light on base unit lights during this whole process 3 After 2 3 seconds you can hear beep sound for two times again and the IN USE light goes off 4 Disconnect the power lead from base Reconnect and you will hear a confirmation tone from the base unit Intercom and transfer To Make an Intercom Call 1 Press the INT 17 key You hear Dial tone 2 Key in the number of the other handset On the other hand
14. User Manual UBiQUiO model 101 Digital Cordless Phone for Skype User Manual User Manual Contents MOGU A tee mee ee RO aCe ner ee mec Oana oer ner 3 FAV SIC al DOI IS estadia lda ici 5 What the Sympos MO Mission titres 6 Setting Up your telephON8 ooocccccccccccconncnnccnnononnconnnnonononnnnnnnnnononnnncnnnonnnnnnncnnnnnnnnnnnos 8 ASTalatiON ansiada co 9 Important safety InforMati0N sesa a E 11 Making a a Answering CallSuciiinsain ia Aca 12 CMW IN es A 14 Conierence AA a a do teacendscandeceuate des 15 PHONG BOOK iaruinn aaa a a R a anes rdopecadss 16 E AAA A es tea atom eas Reagan ae 18 SEUNS add dsids 20 e 1 6 A EE eee ett ee ee ee eee mer cr eee ee ee eee ene ee eee en EE et 28 SKYPE UNCON ci da 28 Resetting Me Ste Mi it 30 MECA ANO AM e e 30 Troubleshooting scsi coat 32 Technical detal ti ii 36 Eeclaration OT CoMo misa is 37 User Manual Introduction Overview Thank you for purchasing our Digital Cordless Phone for Skype We hope that you spend many happy hours using it and chatting with Skype With the UBiQUiO model 101 you can make ordinary telephone call and Internet calls using Skype and SkypeOut 7 An ordinary telephone call is a call between two telephone line subscribers m A Skype call is between two registered Skype users These calls are free of charge n A SkypeOut call is made via the Internet to an ordinary telephone number anywhere in the world using the Skype software This
15. age 20 C to 60 C Electrical power Handset one 1 2 x 2 V 750 mAh Ni MH Rechargeable battery cell Base unit input 230 V AC 50 Hz output AC 7 5 V 350 mA PABX compatibility Timed break recall 100 ms for short flash 250 ms for long flash Pause length 3 seconds Signaling type DTMF dual tone multifrequency Pulse dialing 36 User Manual Declaration of conformity The UBiQUiO model 101 complies with the essential protective requirements and objectives of e EC R amp TTE Directive 1999 5 EC e EC Low Voltage Directive 73 23 EEC e EC EMC Directive 89 336 EEC And conforms to the following relevant harmonized standards TBR 10 1999 TBR 22 1997 TBR 38 1998 EN 301406 V1 5 1 2003 EN 301437 V1 1 1 1999 EN 301489 01 V1 4 1 2002 EN 301489 06 V1 2 1 2002 EN 60950 1 2001 37
16. en key in the PIN the default PIN is 0000 The display shows the numbers from 1 to 5 the maximum call barring numbers you can set 4 Press Left D key and then key in the telephone number you want to set call barring 5 Press Left D key to confirm To Delete Call Barring Number an i h 3 F F 1 See 1 3 step above press the Scrolling W button to select the call barring number you want to delete 2 Then press Left D key the display shows the call barring number you set 3 Press and hold Right E key to clear the number 4 Press Left 5 key to confirm Least cost route LCR function Optional With the LCR function the phone will automatically replace a long number with a comparative short number to simplify the process of dialing a long number For example if the user program to replace 00 with 1790900 then when he dials 006567417211 then the phone will automatically replace the number to be dialed out as 17909006567417211 To Set LCR 1 Select lt LCR gt under Base Settings mode 2 Press Left 5 key and key in the PIN 24 O User Manual Press Left key then key in the SHORT number that you want to replace the long number Press Left S key to confirm then key in the LONG number Press Left D key to confirm To Change Base PIN l 5 Select lt PIN gt under Base Settings mode Press Left S key and key in the original PIN default PIN 0000 number Then press Left
17. er to Settings section of this manual for the information on how to register 6 Download the latest version of Skype from www skype com This is a Windows based installation If you have previously installed the 9 User Manual Skype software proceed to the next step 7 Mount the CD ROM provided into your PC CD ROM Drive and install the program First insert the CD ROM into your PC CD ROM Drive the setup should now start automatically the installation CD Graphic User Interface will appear on your screen The system will prompt you to follow the screen instructions to start and process the installation After a successful install you will find an icon UBiQUiO Skype DECT saved onto the location you choose to save the file and a short cut icon appears on the desktop Note The Skype software must be activated manually on your PC before you place SkypeOut and Skype calls It is recommended to disable your PC from entering sleep mode to ensure the availability of Skype communication Congratulations The installation procedure is now complete If you experience any problems on using this phone refer to the Troubleshooting section elsewhere in this guide 10 User Manual Important safety information This equipment is not designed for making emergency calls in the event of a power failure Alternative arrangements should be made for access to emergency services This means that you should also have a basic phone t
18. h other electronic equipment computers radio TV set clock radio alarms etc A distance of at least one meter should be maintained between model 101 base station and other equipment This will minimize the risk of such interference 7 When you do not need to carry your handsets around leave them on the base unit or charger pod to keep the batteries charged 8 If you hear a warning tone as move around during a call and or the sound in the earpiece becomes faint or distorted you may be going out of range of the base unit Move nearer to the base unit within 20 seconds until the tone stops Otherwise your call may be cut off 11 User Manual Making and Answering Calls Note In standby mode press any button on keypad except Talk button to make the backlight come on before enabling any function It means 1 press to turn on the backlight ae press to activate the function button This is correct for all buttons except for Talk button To Make an Ordinary Call e Enter the telephone number and press Call MA Un key to place call e f you make a a press Right 2 key to delete incorrect digits before you press Call da key To Make a SkypeOut Call SkypeOut allows you to use your Internet connection to call ordinary telephones and mobile telephones worldwide Requires the Skype Out service from Service Provider for landline calls first e Enter the telephone number you wish to call and t
19. hat does not need mains power connected to your line so that you can make calls during a power failure People with a heart pacemaker should consult their doctor before using the telephone If you wear a hearing aid you should note the model 101 works by transmitting radio waves between base and handset that may cause a humming noise 1 DO NOT clean any part of your phone with benzene thinner or other solvent chemicals which may cause permanent damage to your phone This damage is not covered by the Guarantee When necessary clean it with a damp cloth Cleaning it with a wet cloth may give you an electric shock 2 DO NOT use this equipment in places where volatile or explosive materials may be present 3 DO NOT let the base unit get wet Electrical equipment can cause serious injury if used while you are wet or standing in water NEVER use your phone during a thunderstorm Unplug the base unit from the telephone line and the mains socket when there are storms in your area Damage caused by lightning is not covered by the Guarantee 4 The model 101 will produce a certain amount of heat during operation For this reason it is recommended that this equipment is NOT placed in direct contact with antique veneered or delicate furniture surfaces 5 DO NOT dispose batteries with normal household waste never burn them or put them where they could get punctured 6 The model 101 DECT phone emits radio signals which could interfere wit
20. he symbol SkypeOut appears on the left bottom of display then press Left gt key to place call Note The Skype software must be activated on your PC in order to perform SkypeOut and Skype calls To perform SkypeOut calls you also need to set up a user account and top up with call credit at www skype com User can also make SkypeOut call from Call List Phonebook and Skype For the further operation refer to Call List Phonebook and Skype sections elsewhere of this manual To Call a Skype User Make sure the Skype user is available in your Skype net Contact list and is online Otherwise add the online Skype user name you wish to call to the Contacts list of Skype net fist It will automatically appear in your phone s Skype list To call a SRP user 1 Press Scrolling Y WE J button up to enter Skype mode directly the display shows the Soren names 2 Press Scrolling Y Y putton up down to select the name you wish to contact 3 Press Call OA a key to make call 12 User Manual To Answer a Call 1 When the handset and base unit ring press the Call A a key to answer call 2 When the AUTO TALK is turned on you can simply answer the call by lifting the handset from the base unit see AUTO TALK part To End a Call e Press End key to hang up To Dial a Number from Call Logs 1 Select lt Missed Calls gt lt Received Calls gt or lt Dialed Calls gt under CALL LISTS mode
21. lled and are not run down If you experience difficulties with the working of your model 101 refer to the advice given below After mounting the CD ROM provided into your PC CD ROM Drive the installation does not auto run Look for the CD ROM icon UBiQUiO SKype Dect under PC My computer and double click to enter the installation interface manually and select the setup icon Click My computer gt UBiQUiO Skype Dect gt setup The installation CD Graphic User Interface will appear on your screen as following i Setup UBIQUIO Skype DECT ioj xj Welcome to the UBIQUIO Skype DECT Setup Wizard This will install UBIQUIO Skype DECT 2 1 on your computer It is recommended that you close all other applications before continuing Click Next to continue or Cancel to exit Setup Next gt Cancel Next gt Please follow the setup in the wizard and the driver should be able to install successfully If you still can t enter the installation interface please check whether the CD ROM or PC CD ROM Drive is broken If yes contact your supplier immediately 32 User Manual cannot make or answer calls Check that the base units mains power adapter is plugged in and power is switched on The base unit needs mains power for normal operation of the phone not just charging the batteries Make sure you are using the telephone line cable that was supplied with your model 101 Other telephone line cable
22. loser or your call may be cut off Check the Batteries Level symbol on the display If it is low recharge the batteries The Caller Display feature isn t working You need to subscribe to the Caller Display feature from your service provider The caller may have withheld their number or they may be calling from a network that does not transmit the Caller ID for example it may be an international call The handset s batteries are running low within an hour or two Before you used the handset for the first time you should have left it on the base unit for up to 15 hours to charge the batteries fully You may need to replace the batteries 34 User Manual cannot transfer a call Make sure the other handset is within range of the base unit and is not busy on a call Make sure you are keying in the correct number for the other handset No display on LCD screen Make sure the batteries have power cannot register handset to base Make sure the number of handset registered to base is less than 3 Check that the base unit is not near other electrical equipment such as TV or computer 35 User Manual Technical details Full DECT GAP Compatible system Standard Frequency range 1 88 to 1 9 GHz Channel bandwidth 1 728 MHz Modulation GMSK O ti Up to 300 m outdoors pe Up to 50 m indoors Operating time Standby time 90 hours Talking time 10 hours Temperature range Operating 0 C to 40 C Stor
23. microphone is muted Y Signal Level Shows the signal between the handset and base unit and disappear when you are out of range of the base unit K Speakerphone Your handset s loudspeaker is on Chr Lock Your handsets keypad is locked User Manual Setting up your telephone Connection and conditions for use You can connect your model 101 to a direct exchange line DEL a line connected to a local exchange with its own phone number to an extension socket connected to a DEL or to an extension on an approved compatible PBX Do not connect the model 101 as an extension to a payphone How many phones can you connect The ringer equivalence numbers RENs of all instruments phones fax machines etc connected to an exchange line must not add up to more than 4 otherwise one or more of them may not ring and or answer calls correctly The model 101 has a REN of 1 and most other telephones have a REN of 1 unless marked otherwise Radio signals between handset and base unit To use your handset and base unit together you must be able to establish a radio link between them Be aware that e Sitting the base unit as high as possible will give better results in a two storey house the best position may be on the first floor landing e Any large metal object like a fridge a mirror or a filing cabinet between the handset and base unit may block the radio signal e Other solid structures like walls may reduce the signal strength
24. s Left ES key then enter base PIN and press Left key to confirm 5 After a while when the handset finds the base unit it goes back to the standby mode To de register a handset You may need to do this if you have more than one handset registered to your base unit and you need to replace a faulty handset 1 Select lt de register gt under REGISTRATION mode 2 Press Left key then key in the PIN default 0000 3 Press Left D key then key in the number of the handset you want to de register 4 Press Left S key to confirm To register a USB dongle 1 Press and hold the Handset locator button on the base unit for a while until you hear beep sound twice continuously 26 User Manual Insert the USB dongle into your PC USB port Use a paper clip or a pencil tip to depress and hold the register button of dongle for 2 3 seconds then release and you will hear a confirmation tone from Base unit 27 User Manual Extra Settings To Set Alarm Time 1 Select EXTRA under menu mode 2 select lt Alarm Set gt under EXTRA mode 3 Press Left key then press Scrolling button to goes to location ON 4 Press Left 5 key then key in the time 5 Press Left ES key to save To Set Clock Time 1 Select lt Clock Set gt under EXTRA mode 2 Press Left D key then key in the time 3 Press Left key to save To Set Date 1 Select lt Date Set gt under EXTRA mode 2 Press Left
25. s might not work Move the handset closer to the base unit Check the batteries level symbol on the display If it is low replace the handset on the base unit or charger pod to recharge the batteries Switch off power at the mains socket wait for a few seconds and then switch back on This may solve the problem If you still can t make calls try re registering the handset When place Skype call there is no sound Check the network Check Skype interface by following way Click Tools at the Skype interface menu bar and select lt Options gt Then select lt Sound Device gt to enter configuration page Select SDA200 in lt Audio In gt lt Audio Out gt and lt Ringing gt dropdown menu After setting headset cannot be use for communication cannot enter Skype Contact List Make sure Skype software is activated in your PC If so restart Check the connection between USB dongle and your PC and try to plug the USB dongle again When I press keys on the handset nothing happens Make sure the batteries are fitted in your handset lf the batteries level symbol on the display shows low recharge the batteries Check whether there s a key symbol on the display If so the keypad is locked Turn to the user manual to find out how to unlock it When press keys on the handset digits appear on the display but can t make an outside call Call barring may have been set see the user manual for more information
26. set s display your number appears and the INT symbol flashes Then the other handset user presses the Call al key to connect the call For details of how to change the ringing melody and volume for intercom calls see INT MELODY and INT VOLUME under HANDSET SETTING part To End an Intercom Call e Press the Call UA a key on your handset The other person will hear Busy tone and also need to press the End Dy key to hand up To Transfer a Call To transfer the outside call to another handset if you have two or more handsets 30 User Manual 1 Press the INT key and key in the number of the other handset 2 The outside call is put on hold When the other handset answers you can speak to the user If the other handset does not answer you can get back to the outside call by pressing the INT button again To transfer the outside call to another outside phone Network Depending 1 Press the Recall QA key and key in the call number you want to transfer 2 The outside call is put on hold When the call answers you can speak to the user then press the End LIJ key to hang up and transfer the call 31 User Manual Troubleshooting Always check first that e You have followed the steps listed on pages to install and set up your UBiQUiO model 101 e All connects are firmly inserted in their sockets e Mains power is switched on at the socket e The handset s batteries are correctly and securely insta
27. tored numbers 16 User Manual Select the number you want to modify then press Left El key then Scrolling button to the location Edit Entry Press Left key to confirm and Right key to clear the old name then key in the new name Press Left il key to save the edit also goes to the stored number press AN Right L key to clear the old number and key in the new number Then press Left D key to save the change To Check Memory You can use this feature to see how many of your Phone Book s 50 locations have been not used 1 In standby mode press Right E key enter Phonebook mode the display shows the stored numbers 7 Press Left key and Scrolling 47 button to the location memory Press Left S key the display shows n Free To Make Skype Out Call from Phonebook a Under Phonebook mode press Scrolling Y button to select the call number you wish to call Press Left key to enter Option menu then Scrolling Y button to the location Skype out Press Left ES key to place Skype Out call afa User Manual Call Lists You must subscribe to Caller ID service from your service provider to use this feature Call Logs store information related to Received calls Missed calls and Dialed calls The model 101 can store up to a maximum of 30 calls consisting of 10 Received Missed and Dialed calls respectively To Check Call Records 1 Select Call list under menu mode Press
28. umber 4 When connected press and hold button to connect the three parties together y Note Refer to Call Waiting section for how to make Skype Conference Call 15 User Manual Phone Book Up to 50 records could be stored in each handset s Phone Book Each record can store up to 20 digits and names of up to 10 characters In standby mode press Right key and the display shows phonebook list To Enter Phone Book mode There are two ways to enter Phone Book mode as following e Select Phonebook under menu mode e Press Right E i key to enter Phonebook mode directly To Store New Number into Phonebook _ 1 In standby mode press Right key the display shows the stored number 2 Press Left S key and goes to the location New Entry 3 Then press Left E key again and key in the name 4 Press Left S key to confirm and key in the number 5 Now press Left ES key to store it To Delete a Number or All Numbers from dd 1 Under Phonebook mode press Scrolling ne putton to scroll through the stored numbers 2 Select pica numoer you want to delete then press Left key then Scrolling Y uz J button till to the location Delete 3 Now press Left B key to delete current number or all numbers the display shows Delete 4 Press Left 5 key to delete the number numbers To Modify Change a Number in Phonebook 1 Under Phonebook mode press Scrolling button to scroll through the s
29. under menu mode Press Left S key again the display shows Received Calls Dialed calls Missed Calls and Notifications Select e calls type from Received als Dialed calls Missed Calls by Scrolling Y a putton then press Left gt key the display shows these calls numbers Sa one number you wish to call then press left key and Scrolling ES putton to the location Skype Out Press Left D key to place Skype Out call 19 User Manual Settings To Enter Handset Settings Mode 1 Select Settings under menu mode 2 Press Left S key select Handset set under Setting mode the display shows Wall Paper Ringer Set Auto talk Handset Name and Language To Set Wall Paper 1 Select lt Wall Paper gt under Handset Set mode 2 Press Left key to confirm and press Scrolling Cs button to scroll through the pictures 3 Choose the picture you prefer and then press Left 5 key to confirm now the picture is set to the wallpaper of the handset To Set External Internal Ringer Volume 1 5 level 1 Select lt Ringer Set gt under Handset Set mode 2 Press Left key to confirm then Scrolling W button to the location ExternalVo Internal Vol 3 Press Left key and Scrolling button to choose the volume level you want to set 4 Then press Left D key to confirm the choice To Set External Internal Ringer Melody 1 9 melody 1 Select lt Ringer Set gt under Handset Set mode 2
Download Pdf Manuals
Related Search