Home

Cedar Door

image

Contents

1. See handbook enclosed for the 651 667 spring breaking device For doors from 3000mm W x 2500mm H to 3000mm W x 3000mm H Slide the key wayed tube shaft through both springs The tension plug of the anti clockwise wound spring is coded black and should be fitted on the left See figure above For doors up to 5000mm W x 3000mm H Slide each of the two key wayed tubular shafts through a spring Cut the tube shafts of unequal lengths to avoid the coupling from the centre and when there is an electric drive sitting under the drawbar The tension plug of the left wound plug is coded 705GB black and should be fitted on the left See figure Fit to both USA B l USA MINI shafts a bearing and a bearing retainer 395 each with 2 M8 press bolts and nuts to the bearing plate Then fit disassembled halves of the coupler with a cotter USA USA MINI A Fit the spring breaking devices 651LH Rhor 667LH RH to the stationary spring plugs following the drawings that are included in the packaging with every spring breaking device See handbook enclosed for the 651 667 spring breaking device 11 www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk Fit the spring breaking devices 651LH RH or 667LH RH to the stationary spring plugs following the drawings that are included in the packaging with every spring breaking device
2. Hexagonal key 4mm Ring open ended spanner 10 mm Ring open ended spanner 13mm Ring open ended spanner 15mm Ring open ended spanner 17 mm Socket wrench with 1 4 drive Wrench Gluing clamp Cord Water level hose CHECKING DIMENSIONAL DETAILS Before assembling the set the details below should be checked on the basis of this figure Figure 1 Eee Pe S A Clear width B Clear height A C Side area Eg EN D Top area D C Lag Installation area required Springs in front F Springs in rear R Side area C minimum 70mm minimum 70mm Top area D minimum 200 mm manual minimum 70mm manual minimum 200 mm e drive www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk GENERAL SYSTEM DRAWING SPRINGS IN REAR R V fi See et RE E ee E E Mit mep ELp Eer A na Ar n E E Rn e n n a 100 RES X Springs Rear GENERAL SYSTEM DRAWING SPRINGS IN FRONT F MIn150 Min 200 RES 500 2500 3000 LO h FI st RES X Springs Front www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk www thegaragedoorcentre co uk 0800 525 442 INSTALLATION OF VERTICAL TRACK SE
3. 1062M See Bis Figure 5 44 2 Erle NB Make sure that the bottom panel will not be Pl Is a cut for adjusting the panel or door height This O OEE OO should be done with the top section only The attachment of the bottom bracket which is mane holding the complete door weight is relying on the construction of the panel Danger can occur if figures the panel is cut at this point 15 www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk INSTALLING BOTTOM PANEL SPRINGS IN FRONT F 16 General The door panels will be delivered in 2no shrink wrapped packages each with 2 sections of the door face to face together being separated with a layer of bubble wrap cut away the shrink wrapping carefully taking care not to cut the timber panels you will find a plywood strip screwed the bottom edge of some of the panels this is to protect the grooved out section of the joining panels from transit damage You will also find pre fitted to the panels all side and intimidate hinges bottom roller brackets and bottom weather seal so the door can be unwrapped and installed into to opening ready to have the rollers fitted the top roller brackets can only be fitted once all the panels are in place and lined up correctly Important When installing the panels into the opening place a peace of cardboard between the panels to provide the correct spacing
4. 4 through 10 until the correction required has been realized Secure the spring plug on the shaft by turning the bolts in the tension plug in the tube shaft m Remove the final tension lever A Fo Dao TV When the door panel is not hanging completely horizontally in the lifting cables in almost closed condition there are three options for fine adjustment Tube shaft opened door Rotate the drum opposite of the shaft Loosen the securing bolts of the cable drum and rotate the drum relative to the tube shaft For slight movements there is always a risk that the securing bolts slide into the same shallow in the tube shaft and the adjustment is not improved Tighten again the bolts Key wayed tube shaft When a coupler is used 703ST loosen the bolts of the coupler rotate both www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk Springs in front F Slightly loosen the fixation of the shaft suspension to the wall Move the brackets Springs in rear R When the connection suspension profile behind the horizontal tracks has not been finally adjusted the bearing plate support in the slotted holes may be adjusted relative to the horizontal tracks 20 www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk Close the door and secure the door panel with a wrench Loosen the two self tapping screws 1055BV securing the top roller holder so that it can be displaced with a slight tick
5. See installation manual for the 651 667 spring breaking device for details and warnings The fixation of the pall wheel to the shaft should be done by pre drilling a hole in the shaft RIB Doors up to 3000mm wide Slide on both sides a cable drum single door or double door onto the shaft The cable drum coded RH should be fitted on the left side Turn the securing bolts of the cable drum single door to secure these hand tight to the tube shaft Secure each cable drum double door with a key on slotted shaft RIB Doors up to 3000mm wide Fit the bearing plates with spring breaking device with shaft and spring package in conformity with figure below to the bearing plate supports each with 2 M8 press bolts nuts 1070B3 5 and 1068M and the bearing plates each with 1 press bolt and nut 1070B3 5 and 1068m See for correct position figure on next page The position of the bearing plate relative to the bearing plate support will depend on the available installation height www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk Position A the position of the bearing plate support for an available installation height of at least 100 mm Always for electrical drive and may be possible for manual operation illustration 220V Position B the position of the bearing plate support for an available installation height between 70 and 100 mm In many i
6. Torsion springs are subject to considerable tension Proceed at all times with extreme caution Installation maintenance and repair should be carried out only by experienced and properly trained overhead door fitters Use correctly fitting and properly maintained tension levers spanners See attachment www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk 19 www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk Tension the springs by the prescribed number of turns see table below pull the spring 5 mm apart to reduce friction and secure the spring to the tube shaft using the screws of the tension plug 17 Nm Fora shaft with key way one of the screws should be positioned in the key way Number of turns spring Opening height turns each spring 2000 GES 2125 7 8 2250 2375 Tensioning the spring read fully below before attempting to tension the spring Important To apply tension to the springs the spring tensioning plug must be turned in the opposite di rection to which the shaft will turn when lifting the door l pA 3 4 S 6 de 8 9 l l Make sure that the marking strip on the spring forms a sharp line Insert the Ist tension lever completely into the tensioning slot Turn the Ist tension lever a quarter turn such that the spring is tensioned Insert the 2nd tension lever completely into the following tensioning slot Take over the tension of the spring from
7. is free to wind up through the recess in the bearing plate see figure 21 and the cable cannot interfere with the plastic bush 418BUS Secure finally the drum FF 4X8 with the hexagon bolts to the shaft without keyway tightening moment 10Nm For a tube shaft with a keyway the drum FF 4 13 must be secured with a cotter 711A 75 and bolts tightening moment 10Nm O O FITTING CABLE AND TENSIONING SPRING PACKAGE E SPRINGS IN FRONT EI A b s Align the shaft Guide the cable from the bottom bracket behind the bearing roller shafts to the cable drum See figure gt Hook the end of the cable with the end of the pressure clamp circular into the cable drum and turn the cable drum until the lifting cable is taut Align the cable drum in such fashion that the lifting cable is free to wind up Secure finally the drum FF 4X8 with the hexagon bolts to the shaft without keyway tightening O moment 10Nm For a tube shaft with a keyway the drum FF 4 13 must be se cured with a cotter 711A 75 and bolts Block the shaft with for example a wrench Secure the other cable in the same fashion Both cables must be tensioned equally while the door panel is truly level Ensure that the door does not elevate You can do this for example by placing wrenches in the vertical bearing tracks NB Make sure the wrenches are secured tightly CAUTION
8. package containing springs if not included in track package With a five or six panel high door you will receive one extra panel package The door panels will be delivered in 2no shrink wrapped packages each with 2 sections of the door face to face together being separated with a layer of bubble wrap cut away the shrink wrapping carefully taking care not to cut the timber panels you will find a plywood strip screwed the bottom edge of some of the panels this is to protect the grooved out section of the joining panels from transit damage You will also find pre fitted to the panels all side and intimidate hinges bottom roller brackets and bottom weather seal so the door can be unwrapped and installed into to opening ready to have the rollers fitted the top roller brackets can only be fitted once all the panels are in place and lined up correctly Important When installing the panels into the opening place a peace of cardboard between the panels to provide the correct spacing s between the panels if is not done the timber panels could bind and creek due to Expansion www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk TOOLS REQUIRED FOR CORRECT AND RAPID ASSEMBLY Battery drill with Bit 4 0 mm drilling has to be done with installing the spring breaking device Bit 6 5 mm Also for fixing the rubber stop to the track Plug 10 mm Plug 13 mm
9. the Ist tension lever to the 2nd lever Remove the Ist tension lever from the slot Turn the 2nd tension a quarter of a turn such that the spring is tensioned Repeat steps 2 through to 7 until the spring has realized the prescribe number of turns Secure the spring plug on the shaft by turning the bolts in the tension plug in the tube shaft Remove the final tension lever Check the number of turns by counting the number of turns that the marking strip has made Remove the restriction from the door in the tracks and from the shaft and check whether the door is properly balanced When this is not the case you should correct this by tensioning or relaxing by at most 1 turn per spring Make sure when doing this that both springs are equally corrected Correction of the spring tension Insert the 1st tension lever completely into the tension slot Take over the tension from the spring with this tension lever Loosen the bolts in the tension plug Turn the 1st tension lever in the direction required Insert the 2na tension lever completely in the next tension slot Take over the tension of the spring from the 1st tension lever to the 2na tension lever Remove the 1st tension lever from the slot Turn the 2na tension lever a quarter turn in the direction required Insert the 1st tension lever completely into the next tension slot Take over the tension of the spring from the 2na tension lever to the 1st tension lever Repeat steps
10. use door NB WITH THIS DOOR NO ROPE IS BEING SUPPLIED DO NOT INSTALL A ROPE WITH A POWER A OPERATED DOOR AT ANY TIME THIS CAN CAUSE SERIOUS INGOURIES OR DANGER TO THE USER OF THE DOOR OPTION ELECTRICAL DRIVE When you have selected an electrical operator drive RES E 500 or other then this should be assembled in conformity with the handbook supplied with this operator You should clearly follow the instructions for electrical operation in this handbook In order to maintain the closing peak force of the door within the CE standards set the attachment point 97014 of the drawbar should be fixed at the proper position from the upper hinge point Ask your supplier for the correct position NB The person installing the door must check thoroughly if the combination between this door and the selected operator is safe to use Keep in mind the max peak force that is allowed when closing the door People could get hurt if the adjustment of the operator software or the installation of the operator or the selected operator on this door are not checked correctly 22 www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk
11. Insert the 2 M6 press bolts from the inside through the holes in the upper track 1 Fit the M6 flanged nuts and secure hand tight Insert the 2 M6 press bolts from the inside through the holes in the lower track 2 Fit the M6 flanged nuts and secure hand tight ASSEMBLY BEARING PLATE SUPPORT AND SPRING PACKAGE SPRINGS IN REAR R Fit the bearing plate support to the end of the horizontal tracks The position of the bearing plate support relative to the horizontal tracks will depend on the height available for installation see figure 4 Position A the position of the bearing plate support for an available installation space of at least 100 mm Always for electrical drive and for manual operation when there is sufficient gt 90 mm height available Position B the position of the bearing plate a support for an available installation height ea O y o Q D CO QO CD O pu Position A electrical Position B manual www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk SUSPENSION AND CONNECTION HORIZONTAL TRACKS Depending on the selected options one of the following instructions will apply Standard in Flexi Force configuration of sets the suspension is done with suspension bracket and track console This is a ideal method f
12. Press the top panel against the side upper seal and slide the top roller holder in such a position that the roller is placed in the roundings of the curve There must be minimum play between door panel and seal See picture For a manually operated door the bearing roller should be displaced downwards The bearing roller lies snugly in the vertical part of the small curve For an electrically driven door the bearing roller should be displaced upwards The bearing roller lies snugly against horizontal side of the curve Then secure the 2 self tapping screws When the top panel cannot from outside be pushed inwards the remaining self tapping screws may be secured FINISHING THE DOOR Install any additional accessories that you have ordered separately such as Handgrip lock slide bolt etc See attachment for build in instructions NB A slide bolt may not be fitted to an electrically driven door Zus A manually operated door should always be equipped with a hand grip installed at a safe location on the door NB Only lock 650 may be employed when springs are in the rear R because it does not touch the cable NB The minimal build in dimensions are effected by a lock The knob is reaching outside the panel NB For safety reasons always install the grip in the center of a door In that way when opening the door manually there is less risk of injuring hands between de track and rollers To position the rubber door stop 2100 15 open the d
13. T www thegaragedoorcentre co uk LLLLLLL EL 2 First mark A and B on both piers using a spirit level or water level hose and then mark C Figure 1 Prepare vertical tracks by fixing the weather seals before fixing the tracks Fit both vertical tracks with the lower surface on mark line C and the edge 64 mm along the pennant figure 2 The two bearing tracks should be parallel to one another Brickwork or Timber frame SN mm The measurement at this point is the ordering width of door in Weather seals a DD 64mm S Vertical tracks For sloping floors one of the bearing tracks may be compensated for example with a wedge IMPORTANT ALL INSTRUCTIONS FROM NOW ON THAT ARE PREFIXED WITH F REFEARS TO FRONT MOUNTED SPRINGS AND PREFIXED WITH R REFEARS TO REAR MOUNTED SPRINGS D INSTALLATION ASSEMBLING CURVE PLATE SPRINGS IN REAR R If the curve plate is supplied fully assembled with the small upper curve fixed to it only check if below mentioned actions are done in a proper way Assemble the curve plate position the small upper curve picture in blue for springs in rear See picture The short end of this curve is faced downwards fix the curve in the horizontal part with 2 bolts and 2 nuts to the side plate in the related holes A Fix the lower curve to the side plate with 3 bolts and 3 nuts in the related holes Make sure that the flange of the vert
14. according to this manual Installer is responsible for this 6 During tensioning springs can exert large forces Work carefully Use the proper l equipment Ensure that you are standing in a steady position 4 Ensure that there is sufficient light during installation Remove obstacles and dirt Make sure that there is no one else present other than the fitters Other people children may get in the way or endanger themselves during the installation g SPECIAL SAFETY WARNINGS OR REMARKS IN THIS MANUAL ARE INDICATED WITH THIS SYMBOL A READ THESE WARNINGS CAREFULLY GUARANTEE CONDITIONS AND TERMS The general terms and conditions of delivery and payment issued by the Metaalunie and designated as METAALUNIE CONDITIONS are fully applicable to all our quotations contracts and their implementation We expressly reject all other terms and conditions On request we will send you a copy of these terms and conditions free of charge A copy may also be downloaded from our website www flexiforce nl Flexi Force strives to deliver 100 in conformance with the order In practice in spite of all our controls this is not always possible However we will rectify any errors as quickly as possible in order to minimise the inconvenience caused to you or the user As such it is important that you inform us as soon as possible about any problem with the delivery include the order number and week of production and give us the opportunity to offer a suitable s
15. ength is the external side of the bearing plate support The closed side should rest on the flange of the bearing plate support 340 Connect the 50 SU profile to the bearing plate support 340 with 2 M8 mushroom bolts and nuts 1070 3 5B and 1068M Then slide the short profiles 48SU out until they reach a potential suspension point sidewall where they can be secured Then secure finally the securing nuts of the connection between horizontal and vertical track set www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk With horizontal interconnecting profile between the horizontal tracks springs in front F Fit the angle bracket 2602 with 2x press bolt 1062B and 2x flanged nut 1062M to the end of the upper horizontal tracks With horizontal interconnecting profile between the horizontal tracks CW up to 3000mm springs in front F Shorten when necessary the long 50SU profile The profile may then be used as measuring rod L Clear Width 129 mm The ends of the 50SU profile will then correspond with the exterior of the angle bracket Slide first onto both sides the short 48SU profile into the 50 SU profile Then position the long 50SU profile with slotted holes on the angle bracket as mutual connection The closed side should rest on the angle bracket Connect the 50SU profile to the angle support with the M8 press bolts and nuts Then
16. evices ER 651LH RH or 667LH RH to the stationary spring plugs following USA B the drawings that are included in USA MINI the packaging with every spring break device See installation manual for the AN 8511667 spring breaking device for details and warnings The fixation of the pall wheel to the shaft should be done by pre drilling a hole in the shaft Slide on both sides a cable drum FF 4X8 or FF 4 13 onto the shaft The cable drum coded RH should be fitted on the left side Turn the securing bolts of the cable drum to secure these hand tight to the tube shaft Secure each cable drum FF 4 13 with a cotter 711A 75 To install the spring breaking devices to the lintel use the special designed support bracket article code RX563L R Fix the spring breaking device to this bracket Position the assembled shaft and connect the bracket to the side plate with bolt and nut Install the center bearing plate USA MINI to the wall MIN www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk FITTING OF THE DOOR PANELS D General The door panels will be delivered in 2no shrink wrapped packages each with 2 sections of the door face to face together being separated with a layer of bubble wrap cut away the shrink wrapping carefully taking care not to cut the timber panels you will find a plywood strip screwed the bottom edge of s
17. ical angle is placed between side plate and the small upper curve Thus the side plate is positioned on the outside of the vertical angle Now fix the vertical part of the small upper curve with 2 bolts and 2 nuts to the side plate and angle www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk FITTING CABLE PULLEY AND BRACKET TO THE SIDE PLATE R The side plate contains 3 major holes in which to fit a return pulley A B and C See figure The position on the cable pulley depends on the operation of the door electric or manual and the cable diameter It is sufficient to use only 3mm cable for doors in this concept lt 160kg 5x3m For installing the cable pulley and cover plate use following holes NB For the fixation of the cover plate additional smaller holes are provided in the plate Operation Hole Manual operation A E power operation B Insert the M8 press bolt through the cover plate the return pulley the spacer and hole A B see Figure 3 of the reinforced end plate of the assembled curve plate The spacer should be fitted with the flat side against the end plate Fit the M8 nut and tighten it Now fix the M6 bolts and nuts to fix to cover plate on two points If the curve plate is supplied fully assembled with the small upper curve fixed to it only check if below mentioned actions are done in a prope
18. nstances for manual operation illustration hand DO u oo T 540 Ll DO ier ES igj S ASSEMBLY AND FITTING OF SPRING PACKAGE SPRINGS IN FRONT F For doors up to 3000mm W x 2500mm H Slide the tube shaft through both springs The tension plug of the anti clockwise wound spring is coded black and should be fitted on the left See figure below For doors from 3000mm W x 2500mm H to 3000mm H Slide the key wayed tube shaft through both springs The tension plug of the anti clockwise wound spring is coded black and should be fitted on the left See figure below A IMPORTANT SEE INSTALLATION OF 651 667 SPRING BREAK DEVICE THAT ARE INCLUDED IN THE PACKAGING 13 www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk For doors up to 5000mm W x 3000mm H Slide each of the two key wayed tube shafts through a spring The tube shafts are of unequal lengths to avoid the coupling 703ST from the centre and when there is an electric drive sitting under the drawbar The tension plug of the left wound plug is coded black and should be fitted on the left See figure 8a Fit to both shafts a bearing and a bearing holder each with 2 M8 pressed bolts and nuts to the bearing plate USA MINI Then fit disassem bled halves of the coupler 703ST 711A 38 USA B Fit the spring break d
19. olution Cedar Door will only reimburse third party costs if we have given explicit permission for this in advance The reimbursement is based on normal rates and travelling expenses over distances of 1 hour away at most For large scale projects we strongly advise you to first install 1 door completely before installing the other doors In this way any errors can be detected early on and rectified comparatively cheaply This manual does not confer any rights Technical modifications may be made without written notice Flexi Force has endeavoured to design and put together this hardware set in conformance with the applicable CE norms However we recommend to check our configuration against any local national specification www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk www thegaragedoorcentre co uk 0800 525 442 INDEX Before Starting the installation General warnings and instructions Warranty terms and conditions Introduction Tools required for correct and rapid installation General system drawings Installing Installing vertical track Installing assembling curve plate springs in rear R Fitting cable pulley to side plate R Installing assembling curve plate springs in front F Assembly horizontal track set fitting top weather seal Assembly bearing plate support and spring package springs in rear Suspension and connection of horizontal tracks front F Suspension and connection of horizon
20. ome of the panels this is to protect the grooved out section of the joining panels from transit damage You will also find pre fitted to the panels all side and intimidate hinges bottom roller brackets and bottom weather seal so the door can be unwrapped and installed into to opening ready to have the rollers fitted the top roller brackets can only be fitted once all the panels are in place and lined up correctly Important When installing the panels into the opening place a peace of cardboard between the panels to provide the correct spacing s between the panels if is not done the timber panels could bind and creek due to Expansion RIS Installing bottom panel springs at rear R The bottom panel will have the bottom roller bracket and carrier fixed in place you will need to re move the carrier to install the panel position the panel between the vertical tracks and up against the seals the panel must sit level Poi ie ef bi pe d a W e Se K Wi Pons Wi ee d KP O De Wi Insert the shaft of the bearing roller 577 through the loop of the lifting cable k3x k4x until the loop rests in the recess in the shoulder of the bearing roller shaft Insert the shaft of the bearing roller in the bearing roller holder 447S Click the roller protection S80CEN or 581CEN onto the roller Place the roller carrier with roller on the 2 protruding M6 pressure bolts of the e bottom bracket and secure them with 2 M6 flanged nuts
21. oor completely Drill a hole of 6 5mm Fit the rubber doorstop 2100 15 supplied with a press bolt M6x16 1062B and nut M6 1062M to the end of the top horizontal tracks Figure gt Oil all hinges and all bearing rollers with one drop of oil WD40 Greasing of the cables is already done during installation Let some drops of oil go into the curve of the track This lubricates the connection between track and nylon roller which allows a smooth operation of the door 21 www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk The roller shafts are being greased during installation The torsion springs are already lightly oiled Place your CE identification plate on the door mandated together with any warning labels required LABEL GB On the backside Flexi Force LABEL GB sheet you can find instructions on where to place the labels A NB Place a warning label on the lower curve because fingers or hands could be trapped between curve and panel when the door is moving Hand over necessary documents to the end user 1 User manual 2 Dismantling instructions included in this manual 3 Maintenance instructions included in the user manual 4 Service log book 5 Declaration of conformity Ila declaring the door is according to EN 13241 1 Visit www cedardoor co uk for more information on your obligations towards handing over a safe to
22. or a intermediate track fixing Suspension bracket Click console 3022D on the horizontal double track Slide bracket 3021 in the hole between track and console Mount the track console to the sealing with proper fixing material depending on the material of the ceiling Adjust the height and angle of the horizontal track and secure this position with fixing the bolt and nut in the track console With vertical suspension profile of horizontal tracks to ceiling or roof structure springs rear R Fit the perforated angle 30B0750 to the bearing plate support 340 with 2 M8 press bolts and nuts 1070 3 5B and 1068M of 2 Q 2 rr D EN With horizontal connecting profile between the horizontal tracks CW lt 3000 springs rear R Shorten when necessary the long C profile The profile may then be used as measuring rod L Clear Width 134 mm The ends of the 50SU profile will then correspond with the exterior of the bearing plate support Slide first onto both sides the short 48SU profile into the 50 SU profile Then slide long C profile with slotted holes on both ends into the rectangular recess of the bearing plate support 340 as mutual connection The closed side should rest on the flange of the bearing plate support 340 With horizontal connecting profile between the horizontal tracks CW gt 3000 springs rear R Slide both C profiles into each other Mark of a length of L CW 134 mm This l
23. r way Assemble the curve plate position the small upper curve for springs in rear See picture The short end of this curve is faced downwards fix the curve in the horizontal part with 2 bolts and 2 nuts to the side plate in the related holes A Fix the lower curve to the side plate with 3 bolts and 3 nuts in the related holes Make sure that the flange of the vertical angle is placed between side plate and the small upper curve Thus the side plate is positioned on the outside of the vertical angle Now fix the vertical part of the small upper curve with 2 bolts and 2 nuts to the side plate and angle Position the end of the curve in line with the vertical angle Then fix the M6 flange nut and bolt through the hole www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk Keep FITTING OF TOP WEATHER SEAL Top weather seal as shown across is fixed to either the timber sub frame head frame or direct to the rear of the lintel by method of the steel fixing clips so the seal is allowed to hang down passed the top edge of the top panel nn WEATHER SEAL ASSEMBLY HORIZONTAL TRACK SET Attach a piece of rope to the ceiling or the roof structure to maintain the elevation of the rear side of horizontal tracks during the assembly process Slide the horizontal tracks in the direction of the vertical track set A
24. rict our instructions for the proper assembly of the complete door For installation of not mentioned products or parts including any components added by the supplier as well as for a user handbook we refer you to the supplier of the complete overhead door who is also responsible for the correct CE marking of the door These instructions have been prepared for use by experienced professional fitters and are therefore not suitable for the DIY fitter or the apprentice fitter The article codes of the parts are given in parentheses This door can only be installed according to the CE certificate if all parts are according to the parts lists of the SP certificate See www flexiforce com Flexi Force has applied the mandated INITIAL TYPE TESTING for doors described in this manual at the SP Institute in Sweden as Notified Body Nr 0402 The INITIAL TYPE TESTING REPORT that has been rewarded can be transferred to the door producing company This is needed to complete your CE files according to product standard EN13241 1 NB This garage door cannot be equipped with a pass door wicket door All CE approvals are not A valid when a pass door is installed If you want to include a pass door a new Initial Type Testing should be arranged under your responsibility Receipt and delivery of door With a four panel high door you will receive two packages containing panels one package containing tracks one package containing fittings and one
25. s between the panels if is not done the timber panels could bind and creek due to Expansion The bottom panel will have the bottom roller bracket and carrier fixed in place position the panel be tween the vertical tracks and up against the seals the panel must sit level Hook the loop of the lifting cable k3x or k4x to the pin intended for that purpose on the bottom bracket 422 S pel First click the roller protection 580CEN or nnn o 581CEN onto the roller P e Insert the shaft of the bearing roller 590 25 ped through the spacer 2066 07 and the holes of the bottom bracket 422LH RH intended for that Ji purpose Place then the bearing roller first in the f x Bo gt II bearing track and then secure the bottom brackets 1055RBV amp S gt ED J with the self tapping screws 1055BV See figure e A Ji 16 www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk PLACING PANELS Place stack the remaining panels and secure the upper leaf of the side and central hinges to the panels Important When installing the panels into the opening place a peace of cardboard between the panels to provide the correct spacing s between the panels if is not done the timber panels could bind and creek due to Expansion Adjust the roller to the side hinge such that the nylon of the roller is located in the rounding of
26. slide the short profiles 48SU out until they reach a possible suspension point sidewall to which a connection can be made With horizontal interconnecting profile between the horizontal tracks CW over 3000mm springs in front F Slide both C profiles into each other until the length required is realized and minimum overlap is 500 mm Mark of a length of L Clear Width 129 mm This length is the external side of the angle bracket Then position the C profile with slotted holes 50SU2750 on the angle bracket 2602 as mutual connection The closed side should rest on the angle bracket Connect the C profile to the angle support with the M8 pressed bolts and nuts 1070 3 5B en 1068M Secure the C profile to any suspension point sidewall involved www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk 10 cl cl www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk ASSEMBLY AND FITTING OF SPRING PACKAGE SPRINGS IN REAR R For doors up 3000mm W x 2500mm H Slide the tube shaft 701 through both springs The tension plug of the anti clockwise wound spring is coded black and should be fitted on the left See figure below H Fit shaft support off centre when a KEES electric operator is to be used _ Fit the spring breaking devices 651LH Rhor 667LH RH to the stationary spring plugs following the drawings that are included in the packaging with every spring breaking device
27. tal tracks rear R Assembly and fitting of spring package springs in rear R Assembly and fitting of spring package springs in front F Fitting the door panels Installing bottom panel springs in front F Jand rear R Placing panels Installation of roller carrier springs in rear R Installation of roller carrier springs in front F Fitting cable and tensioning the spring package springs in rear R Fitting cable and tensioning the spring package springs in front F Finishing the door Option electric drive www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk a BR We oo Gi Al ANA 11 12 13 14 15 16 17 17 18 18 19 21 www thegaragedoorcentre co uk cl cl www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk INTRODUCTION Flexi Force has developed a completely new hardware set for residential garage overhead doors Designed for all built in situations depending on the available space The set includes the following features Suitable for single and double garages to W x H 5 x 3m max Spring package behind the horizontal tracks R needed head room 70 100mm or Spring package in front F at the lintel needed head room 200mm Fitted with cable within the tracks and spring breaking device meeting CE standards Restricted installation 1 2 3 4 5 6 CE approved when selecting the proper Flexi Force compo In this handbook we shall rest
28. the spacer 2066 10 into the sleeve of the top roller carrier see figure Place the roller in the short curve and fix the top roller carrier 417 to the upper side of the top panel with 2 self tapping screws 1055BV in both slotted holes figure The remaining self tapping screws 1055BV will be secured at a later stage The position of the top roller in the small curve is determined by the operation 0800 525 442 Position A manual operation top panel is locked when door is closed Position B power operation e operator can draw the roller into the horizontal track NB Do not install a 580CEN roller protection on the top roller Dies H S Ee FITTING CABLE AND TENSIONING THE SPRING L PACKAGE SPRINGS IN REAR R Align the shaft Grease the cables AT he II be oh 4 Guide the cable from the bottom bracket behind the bearing roller shafts and over the return pulley to the cable drum See figure gt www thegaragedoorcentre co uk www thegaragedoorcentre co uk 2066 10 500 25 0800 525 442 www thegaragedoorcentre co uk 18 www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk Hook the end of the cable with the end of the pressure clamp circular into the cable drum and turn the cable drum until the lifting cable is taut Align the cable drum in such fashion on the tube shaft that the lifting cable
29. the track and that the play between panel and side seal is at a minimum The shaft of the bearing roller should remain capable of turning by hand Fix this position by fixing the slide roller carrier onto the base of the side hinge by means of 2 bolts 1062B and two nuts 1062M First click the roller protection 580CEN or 581CEN onto the roller INSTALLATION TOP ROLLER CARRIER SPRINGS IN REAR R Slide the plastic bush 418BUS over the bush of the top roller Pl holder Be 418LH RH Then slide the shaft of the roller 576 into the bush of NK the top roller holder See figure SH CA Place the roller in the small upper bend and fix the top roller holder a R 418LH RH to the upper side of the top panel with 2 self tapping e d screws 1055BV in both slotted holes The remaining self tapping oO ec screws 1055BV will be secured at a later stage The position of 418 the top roller in the small curve is determined by the operation Position A manual operation top panel is locked when door is closed Position B power operation e operator can draw the roller into the horizontal track NB Do not install a 580CEN roller protection on the top roller 17 www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk www thegaragedoorcentre co uk INSTALLATION TOP ROLLER CARRIER SPRINGS IN FRONT F Slide the shaft of the roller 590 25 through
30. www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk Cedar Door Installation instructions for Timber Sectional doors www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk www thegaragedoorcentre co uk 0800 525 442 www thegaragedoorcentre co uk ATTENTION GENERAL WARNINGS To install use and maintain this door safely a number of precautions must be taken For the safety of all concerned pay heed to the warnings and instructions given below If in doubt contact your supplier This manual has been written for use by experienced fitters and as such is not l suitable for d i y purposes or for use by trainee fitters 2 This manual describes the installation of the hardware set components door l sections panels and refers to installation manuals of the electrical operator Be sure to supplement this manual if needed with instructions for any additional components not described in this manual 3 Before starting read this manual carefully Certain components may be sharp or have jagged edges As such you are advised to 4 wear safety gloves All the components which have been supplied are designed for use with this specific overhead door Replacement or adding additional components may have an adverse effect on the safety of and the guarantee on the door Also the CE approval which has been granted to this door will be cancelled when components are changed or installation is not done

Download Pdf Manuals

image

Related Search

Related Contents

Samsung GW76V-WW Manuel de l'utilisateur  Varian 400-DS Op Man 70-9051 Rev A  R2 DX/LS User Manual - The Science of Sure – HOLOGIC    Invacare® Alegio NG  ACRITÓN CUBIERTAS  Fellowes 4200CC Paper Shredder User Manual  2755-NU003, Hand-Held Scanner with Wedge Option User Manual  

Copyright © All rights reserved.
Failed to retrieve file