Camera ID Setup - CBC Group
Contents
1. NOTE Be careful not to pull the cables improperly during installation Additionally it is suggested to fasten the cables after cable connection is completed Furthermore when wiring the AC 24V power cable make sure the Ground wire inserted into the mid pin of the terminal block The PTZ Camera s 22 pin connector definition is listed as shown below 1 21 Pin Definition Cable Pin Definition Cable 1 AC24 1 DC 20AWG 18AWG 12 ALM 1 2 ALM NC 13 ALM 3 3 AC 24 2 DC 20AWG 18AWG 14 ALM 2 4 ALM NO 15 ALM 4 5 20AWG 18AWG 16 ALM 5 6 ALMCOM 17 ALM 6 7 T 18 ALM 7 8 19 ALM 8 9 IT atone 20 ALM GND 10 R 21 VGND ISOG 22 Video ANG 15 2 7 User s Manual RS 485 Connector Definition RS 485 is the interface that communicates the analog PTZ Camera and its control device Please connect the control keyboard to the PTZ Camera through the terminal block The recommended cables for RS 485 communication are CAT 5 cables maximum cable length for over 24 gauge wire is 4000 feet 1219 meters If the total cable length exceeds 4000 feet using a repeater to maintain the signals is recommended Please refer to the figure and table below for pin definition and wiring 00000 Corresponding Pins 22 Pin Connector pesi 1 7 10 T R D 2 4 Reserved 5 8 9 T R D2. Layer 1 Layer 2 Layer 3 Notes AUTOPAN CRUISE PRESET POINT 001 256 SEQUENCE LINE 001 008 AUTOPAN LINE 001 004 CRUISE LINE 001 008 001 127 SEC DWELL TIME A EXIT YES DETECT SWITCH ON OFF DETECT MODE lt MOTION gt BLOCK MODE lt NONE gt lt ON gt lt OFF gt ALARM DETECT FRAME SET NONE MOTION 01 04 FRAME DISABLE NONE MOTION 01 04 THRESHOLD NONE MOTION lt 001 gt lt 255 gt EXIT YES WDR FUNCTION ON OFF PRIVACY SWITCH D e AE TRANSPARENCY ON OFF BLACK WHITE RED GREEN COLOR BLUE CYAN lt YELLOW gt lt MAGENT PRIVACY MASK A gt CENTER UR V CENTER D U SET MASK 01 16 H SIZE 000 080 V SIZE 000 060 EXIT SAVE CLEAR MASK lt 01 gt 16 EXIT YES TIME DISPLAY lt ON gt lt OFF gt SET YEAR 00 99 SET MONTH 01 125 TIME SETTING ENTER SET DAY 01 31 SET HOUR 00 23 SET MINUTE 00 59 EXIT SAVE YES SCHEDULE EU ON OFF OFF POINT 01 32 01 HOUR 00 23 00 MINUTE 00 59 00 NONE NO FUNCTION PRESET POINT PRESET c SEQUENCE LINE SCHEDULE SEQUENCE 001 008 AUTOPAN LINE MODE AUTOPAN CRUISE LINE CRUISE tc es IR FUNCTION IR FUNC AUTO ON OFF SCHEDULE RESET YES EXIT OSD YES 65
3. Termination Line Lock SW 5 Factory Default Reset swe Camera Upgrade RS 485 is the interface that communicates the PTZ Camera and its control device for this reason the RS 485 setup of the PTZ Camera and the control device must be the same The RS 485 default setting is half duplex see the diagram follows Please do not change the default setting without qualified specialist or supplier s notice As for the SW 3 and SW 4 they are used for termination and Line Lock adjustment respectively The SW 5 is mainly used when users want to restore the camera to the factory default status moreover once firmware upgrade is carried out users need to reset the SW 6 afterward RS 485 Setting Half duplex Full duplex ON ON T2 1 2 User s Manual 2 4 ID Setup Please change the PTZ Camera s ID if there is more than one PTZ Camera in the same network Use the switch to change your PTZ Camera s ID by setting the 10 bit dip switch For instance if the camera s ID is 006 set the SW 2 and SW 3 to ON with the rest to OFF as shown below ann 112 3 45 67 910 For switch configuration details please refer to Appendix B Switch Settings Index Table NOTE No two PTZ Cameras should be given the same ID or communication conflict may occur 2 5 14 User s Manual Camera Control Protocol Setup Define the protocol you are going to use basing on the devices o
4. User s Manual Operation and Configuration 3 1 OSD Display Format Information shown on the screen are described in terms of OSD display position and function description see the table below Position Function OSD Display Description A Auto Focus Mode 1 Focus Modes M Manual Focus Mode X Back Light Compensation OFF 2 Backlight B Back Light Compensation ON 3 Alarm ALARM Alarm Message Present Zoom Ratio Poom ane al Optical Zoom Digital Zoom e Maximum 20 characters for each title 5 Title e 16 sets of title are available 6 Camera ID Show the camera ID 17 User s Manual 3 2 OSD Menu Tree The OSD setup menu structure is listed in the following section The star symbol indicates the factory default For detailed function description please see section 3 3 Configuration Menu Mini PTZ Camera Menu Tree Layer 1 Layer 2 Layer 3 Default lt ENGLISH gt lt PORTUGUESE gt lt SPANISH gt lt FRENCH gt LANGUAGE GERMAN ITALIAN ENGLISH lt ON gt lt OFF gt ON BACKLIGHT lt ON gt lt OFF gt OFF lt AUTO gt AF MODE NORMAL 7 TRIG lt PTZ TRIG gt AUTO FOCUS EXIT SAVE YES lt MANUAL gt EXPOSURE BD n VALUE lt 10 5dB gt COME EXIT SAVE YES BRIGHT VALUE SHUTTER SPEED AUTO IRIS VALUE GAIN VA
5. IR FUNCTION IR FUNC AUTO ON OFF 20 User s Manual Item Layer 1 Layer 2 Layer 3 Default EXIT OSD YES 21 3 3 3 3 1 22 User s Manual Configuration Menu The detailed functions and parameter setting of your PTZ Camera can be set by the OSD On Screen Display menu with a control device such as a control keyboard The tables below show each page of the OSD menu Additionally Appendix B provides a table for user s setting record To enter the OSD menu of the selected camera press lt CAMERA MENU gt key on the control keyboard and hold for 3 seconds to enter the OSD menu To select the setup item use direction keys on keyboard to move the OSD cursor in the OSD menu To setup item use direction keys on keyboard to move the OSD cursor in the OSD menu For items with press right left direction keys on the control keyboard to select For items with press the CAMERA MENU key the control keyboard to enter the sub menu For items with users use the right left direction keys to select functions and then press the CAMERA MENU key on the control keyboard to enter their sub menu For further detailed setup procedures please refer to the user s manual of your installed control devices NOTE In the Camera OSD menu the lt CAMERA MENU gt key functions as ENTER and EXIT LANGUAGE The camera supports multi language OSD ope
6. Iris Control Electronic Shutter AGC control Auto Manual 1 1 1 10k sec Auto Manual Back Light Compensation On Off OPERATION Built in Protocol DynaColor Pelco D amp P VCL Philips AD 422 JVC etc Multi Language OSD English French German Italian Portuguese Spanish Pan Travel 360 endless Tilt Travel 10 190 Manual Speed 1 80 5 Presets 256 Preset Accuracy 0 225 Preset Speed 10 400 s Sequence 8 Auto Pan 4 Cruise 8 Privacy Mask 16 Proportional Pan amp Tilt On Off Pan and tilt speed proportional to zoom ratio Resume after Power loss Yes Zone Title 16 Home Function Preset Sequence Auto pan Cruise Auto Flip Digital Mechanical Off Digital Slow Shutter On Off 53 User s Manual Motion Detection On Off Wide Dynamic Range On Off Day Night IR Cut Filter On Off Image Freeze On Off Image Inverse On Off Noise Reduction e 3D On Off Alarm Input 8 Alarm Output 1 Alarm Reaction Preset Sequence Auto pan Cruise GENERAL Environment Indoor Controller Interface RS 485 Operating Temperature 0 C 40 C 32 F 104 F Dimension 2131 x 200 mm 5 2 x 7 9 Inches Weight 1 2 kg 2 6 Ibs Power Source DC12V AC24V 10 Power Consumption 14 W Regulatory CE FCC R
7. 3 3 22 TIME SETTING The time setting function is used to set the TIME related parameters of the PTZ Camera Each item in the menu is listed as follows TIME SETTING TIME DISPLAY SET YEAR SET MONTH SET DAY SET HOUR SET MINUTE EXIT SAVE e TIME DISPLAY Select lt ON gt to display Time information on the screen or lt OFF gt not to display e YEAR MONTH DAY The items are for setting up the system date e HOUR MINUTE The items are for setting up the system time e EXIT SAVE Exit the TIME SETTING menu and go back to the MAIN PAGE 3 to carry on setup of schedule MAIN PAGE 3 IR FUNCTION ALARM SETTING ALARM DETECT WDR FUNCTION PRIVACY MASK TIME SETTING SCHEDULE EXIT OSD 50 User s Manual 3 3 23 SCHEDULE FUNCTION The schedule function enables users to program a preset point or function Sequence Auto pan Cruise automatically to perform in a specific period of time SCHEDULE SWITCH POINT HOUR MINUTE MODE PRESET POINT SCHEDULE RESET EXIT e SCHEDULE SWITCH Select to enable or OFF to disable the schedule function e SCHEDULE POINT Users are allowed to arrange 32 sets of schedule point i e each set of schedule point can be assigned one kind of schedule modes e SCHEDULE HOUR MINUTE The items are for setting up the time to execute each schedule point e SCHEDULE MODE This is for setting the schedule function of the selected schedule point the options are lis
8. In this mode the camera will keep in focus automatically and continuously in any condition Zoom Trigger Mode In this mode AF is activated at the time when zoom is changed PTZ Trigger Mode In this mode AF is triggered when the PTZ Camera is manipulated to pan tilt or Zoom EXIT SAVE Press YES on this item to save the selected AF Mode 23 3 3 5 24 User s Manual MANUAL In this mode users can adjust focus near far via the control keyboard s Focus Near Far key AE MODE Exposure is the amount of light received by the image sensor and is determined by how wide you open the lens diaphragm iris adjustment by how long you keep the sensor exposed shutter speed and by other exposure parameters With this item users can define how the Auto Exposure AE function works EXPOSURE COMPENSATION The exposure value rages from 10 5dB 10 5dB Select lt OFF gt to disable the function AE MODE AUTO In this mode the camera s Brightness Shutter Speed IRIS and AGC Auto Gain Control control circuits work together automatically to get consistent video output level SHUTTER With this option Shutter Speed takes main control of exposure and both IRIS and AGC will function automatically in cooperation with shutter speed to achieve consistent exposure output The shutter speed ranges from 1 10000 1 50 IRIS In this mode the IRIS function adjusts exposure in higher property SHUTTER speed and AGC ci
9. condition is released or users rotate the joystick to change the status of the PTZ Camera A NOTE The dwell time is only adjustable when selecting Preset as the alarm action When the dwell time is up the PTZ Camera will go back to its trigger position and recheck alarm pin status EXIT Exit the ALARM SETTING menu and go back to the MAIN PAGE 3 to carry on Privacy Mask setup MAIN PAGE 3 IR FUNCTION ALARM SETTING ALARM DETECT WDR FUNCTION PRIVACY MASK TIME SETTING SCHEDULE EXIT OSD User s Manual 3 3 19 ALARM DETECT When the Alarm Detect function is activated the camera will detect movement within a monitoring area and then send an alarm signal automatically There will be a flash warning notice MOTION displayed in the upper left corner of the screen ALARM DETECT DETECT SWITCH OFF DETECT MODE NONE BLOCK MODE NONE FRAME SET NONE FRAME DISABLE NONE THRESHOLD NONE EXITD YES e DETECT SWITCH The item is used to enable or disable the ALARM DETECT function e BLOCK MODE In Motion Detect Mode users can set Block Mode as ON or OFF When BLOCK MODE is turned on if there are any variations e g caused by intrusion in the sections of the monitoring image the affected parts will be highlighted dynamically e FRAME SET In a monitored field users can define specific areas as motion detection target zones Please refer to the instructions as follows to configure parameters for each motion detec
10. memorize the present position as a privacy mask position Up to 16 masks can be set User s Manual MASKO1 MENU H CENTER V CENTER H SIZE V SIZE EXIT SAVE H CENTER The original horizontal center ofa mask zone is the center of a screen it is able to move a mask zone to the other position by adjusting the horizontal value with the LEFT RIGHT keys on the keyboard The camera will pan right or left according to user s control V CENTER The original vertical center of a mask zone is the center of a screen it is able to move a mask zone to the other position by adjusting the vertical value with the LEFT RIGHT keys on the keyboard The camera will tilt up or down according to user s control H SIZE 00 80 Users can adjust the horizontal size of a privacy mask through this item Set the H and V size to 0 can also delete the selected mask V SIZE 00 60 Users can adjust the vertical size of a privacy mask through this item Set the H and V size to 0 can also delete the selected mask CLEAR MASK Users can delete a preset mask zone with this item Please follow the steps listed below 1 Select the mask zone that will be erased e g 01 2 Press ENTER to confirm the selection EXIT Exit the PRIVACY MASK menu and go back to the MAIN PAGE 3 to carry on time related setup MAIN PAGE 3 IR FUNCTION ALARM SETTING ALARM DETECT WDR FUNCTION PRIVACY MASK TIME SETTING SCHEDULE EXIT OSD 49 User s Manual
11. speed of one sequence point to the next one and the range of setup speed is from 1 to 15 Within the range PAN and Tilt speed varies from 5 300 degree sec e DWELL TIME The DWELL TIME is the duration time that the PTZ Camera will stay at a sequence point and the range is from 0 to 127 seconds The PTZ Camera will go to the next sequence point when the DEWEL TIME expires If the setting is lt O gt the PTZ Camera will stay at this sequence point until users manually move the camera 34 User s Manual RUN SEQUENCE Users can command the PTZ Camera to run the selected sequence line manually EXIT Select the item to exit the SEQUENCE menu go back to the MAIN PAGE 2 to carry on setup of auto pan MAIN PAGE 2 ID DISPLAY TITLE DISPLAY TITLE SETTING PRESET SEQUENCE AUTOPAN CRUISE HOME SETTING NOTE Users could execute the sequence function through a keyboard Please refer to the control keyboard s quick guide for further information 3 3 14 AUTOPAN Auto pan means motion of scanning an area horizontally so that the PTZ Camera can catch horizontal view The parameters are listed as follows AUTOPAN AUTOPAN LINE 1 START POINT TO FIND END POINT TO FIND DIRECTION RIGHT SPEED 01 RUN AUTOPAN ENTER EXIT YES AUTOPAN LINE There are four sets of auto pan line built in a PTZ Camera Users can choose a line to execute using LEFT RIGHT direction keys In addition users are able to command the PTZ Cam
12. the control keyboard to change the setting and the items mentioned below will change in cooperating with your selection PRESET POINT Select a Preset Point where the PTZ Camera should go after the Return Time function which will be mentioned later is activated The preset point s should be set prior either in the PRESET setup menu or through the keyboard SEQUENCE LINE Select a Sequence Line that the PTZ Camera should execute when an alarm pin is triggered The Sequence Line s should be defined previously in the SEQUENCE setup menu AUTOPAN LINE Select an Auto pan Line that the PTZ Camera should execute when an alarm pin is triggered The Auto pan Line s can be defined in the AUTOPAN setup menu 39 40 User s Manual CRUISE LINE Select a Cruise Line that the PTZ Camera should execute when an alarm pin is triggered The Cruise Line s can be defined in the CRUISE setup menu RETURN TIME The PTZ Camera starts to count down RETURN TIME when the camera idles and it will execute the SELECT MODE function if the return time is up The RETURN TIME ranges from 1 to 128 minutes GO If HOME function is enabled the users are allowed to execute HOME function manually by selecting this item EXIT Exit the HOME SETTING menu Then go to the MAIN PAGE 3 to carry on other setups MAIN PAGE 3 IR FUNCTION ALARM SETTING ALARM DETECT WDR FUNCTION PRIVACY MASK TIME SETTING SCHEDULE EXIT OSD User s Manual 3 3 1
13. 3 3 6 WBC T rr 25 3 3 7 SETUP MENU A sin kika py kask 26 DIGITAL LOOM as idea antank tas aba ko 26 Rec BIET p TE 26 DIGITAL NOISE REDUCTION D IN E iini teniendo bna eq ma tna ear 27 IMAGE usi ct a 27 PREEZ HQ 27 APERTURE ee RT att te e a ok Ga ky ena aS 27 cp p kota id Pe ta a av ka e yn e ak a a 28 3 3 8 SETUP MENU ks kn E gen en sok E ke e ki kap ke 28 FLIP kt a 28 ANGLE ADJUSTER kata ind A ka ok a kk a n ab e kk ka e A Pa n 29 SPEED BY ZOOM fe ni it a at e a ke il 29 AUTO CALI Auto Calibration cia ke ep bren pis ake panike 29 PASSWORD e H 29 OSDAUTO CLOSE e pr E 30 SYO TEMRE SE Fot li soti anba t a pat ya kk hi aaa MIS a ek ek ai 30 ee ke at a e kila ke pr a ka kt A e at ra ka oo bOs pk kb dak aa 31 33 9 ID a e kk TA 31 22 10 EE FLAN ds SS ay ka e e pe ran kan a bk ka ky n 31 3 311 TITLE SETTING oh cs TTC 32 User s Manual PRESE D 33 Km Yi SEQUENCE eee ere eer its eti 34 em EM Ie 35 S319 CRUIS
14. 7 IR FUNCTION With the IR cut filter the PTZ Camera can still catch clear image at night time or in the very dark light condition During day time the IR cut filter will be on to block the infrared light for clear image during night time or in dark light condition the IR cut filter will be removed to catch infrared light and the displayed images will become black and white e AUTO The Internal circuit will automatically decide the occasion to remove the IR cut filter according to the value of light condition calculated by the internal light algorithm The options include LOW MID and Hl LOW indicates a higher sensitivity and can improve reliability of lens so that it is easier to switch to Day mode and relatively difficult to change into Night mode while Hl indicates that it is easier to switch to Night mode and difficult to change into Day mode e MANUAL IR MANUAL ON Select the item to remove the IR cut filter the camera will be in B W Night mode IR MANUAL OFF Select the item to attach the IR cut filter the camera will be in Color Day mode to disable the IR function 41 User s Manual 3 3 18 ALARM SETTING The Mini PTZ Camera provides eight alarm inputs and one alarm output N O and N C to connect alarm devices With this function the PTZ Camera will cooperate with alarm system to catch the event images For wiring please refer to the installation guide and or qualified service personnel A
15. E ED a id EN INDE 37 8 3 16 HOME SET TUNE itin dant tst d abad nut ae ade 39 3 3 17 IR FUNCTION rH 41 3 0 18 C 42 33 19 ALARM DETECT ANA E dS 45 9 39 20 WDR FUNC TION T 47 3 3 21 PRIVACY MASK Cm 48 3 3 22 TIME Saliha E bik ki ek vo ba ie 50 3 3 23 5 51 3 93 24 e gay gan 52 Appendix A Technical 53 Appendix B Switch Settings Index 55 Camera ID Setups E 55 PFOLOCON S OU PI ai kass 62 Appendix C OSD Menu Nol65 be koko vini be koken ko oke pi ki ko ie e a MEE kn a ka eee 63 User s Manual 1 Overview The Mini PTZ Camera is an innovative PTZ Camera designed for middle and small surveillance applications and possesses true PTZ Camera features such as high speed and accurate Pan Tilt up to 12x12 zoom ratio 180 Digital Image Flip Speed by Zoom and Preset Speed up to 400 s Additionally it contains 256 Preset Points 8 Sequence Lines 4 Auto Pan Lines and 8 Cruise Lines to
16. ERTURE Users can adjust enhancement of the edges of objects in the picture There are 16 levels of adjustment the options are lt 01 gt lt 16 gt 01 represents no enhancement When shooting text this function could make it sharp 27 3 3 8 28 User s Manual EXIT Exit the SETUP MENU 1 and go back to the MAIN PAGE 1 to set other functions under the setup menu 2 MAIN PAGE 1 LANGUAGE DEFAULT CAMERA BACKLIGHT FOCUS AE MODE WBC MODE SETUP MENU 1 SETUP MENU 2 SETUP MENU 2 The SETUP MENU 2 is as shown below SETUP MENU 2 FLIP ENTER ANGLE ADJUSTER ENTER SPEED BY ZOOM OFF AUTO CALI OFF PASSWORD OFF OSD AUTO CLOSE 20 SEC SYSTEM RESET ENTER EXIT YES FLIP Users can track an object continuously when it passes through under the PTZ Camera with setting Flip to IMAGE digital flip or M E mechanical flip FLIP SETTING FLIP OFF EXIT SET YES IMAGE IMAGE represents digital IMAGE FLIP which enables users to keep tracking objects seamlessly under the mode almost no delay occurs in comparing with that under the M E mode NOTE The Privacy Mask function will be automatically disabled if the Image Flip function is enabled and the screen will show MASK WILL BE SET OFF User s Manual M E M E is a standard mechanical operation As the Camera tilts to the maximum angle it will pan 180 and then continue tilting to keep tracking objects OFF Select this item to dis
17. I J SAVE KL 5 T LEFT UVWX YZ RIGHT DELETE TITLE ABC Choose a character with direction keys and then press the lt CAMERA MENU gt key ENTER to input For example lt A gt lt CAMERA MENU gt lt B gt lt CAMERA MENU gt lt C gt lt CAMERA MENU gt TITLE ABC To delete input characters move the cursor to lt LEFT gt or lt RIGHT gt and press lt CAMERA MENU to select a character in the entry field Then move the cursor to lt DELETE gt and press lt CAMERA MENU to delete the selected character STEP 7 When the setting is completed move the cursor to lt SAVE gt and press to save After completing tile setting go back to the MAIN PAGE 2 to carry on setup of preset points MAIN PAGE 2 ID DISPLAY TITLE DISPLAY TITLE SETTING PRESET SEQUENCE AUTOPAN CRUISE HOME SETTING User s Manual 3 3 12 PRESET PRESET SET Totally 256 preset points can be set Follow the steps below when in the preset setting menu STEP 1 Press the right left key on the keyboard to select a number 1 represents preset point 1 2 represents preset point 2 etc STEP 2 Press the lt CAMERA MENU gt key ENTER on the keyboard and then rotate the PTZ Camera to a targeted shooting area point STEP 3 Press the lt CAMERA MENU gt key again to save the defined preset point Once completing setup of a preset point users could move the cursor to the next
18. IRIS VALUE GAIN VALUE AUTO EXIT SAVE YES SHUTTER SPEED PAL lt 1 50 gt lt 1 10000 gt SEC SHUTTER NTSC lt 1 60 gt lt 1 10000 gt SEC AE MODE EXIT SAVE YES K MODE l IRIS VALUE lt F1 6 gt EXIT SAVE YES BRIGHT VALUE AUTO SHUTTER SPEED PAL lt 1 50 gt lt 1 10000 gt SEC MANUAL NTSC lt 1 60 gt lt 1 10000 gt SEC IRIS VALUE lt F1 6 gt GAIN VALUE lt 3 gt dB lt 28 gt dB EXIT SAVE YES EXIT SAVE YES AUTO Auto White Balance INDOOR OUTDOOR WBC MODE ATW Auto tracing WBC RGAIN 000 127 MANUAL GAIN 000 127 EXIT SAVE YES ZOOM SPEED lt 8 gt DIGITAL ZOOM lt ON gt lt OFF gt SLOW SHUTTER lt ON gt lt OFF gt 2D N R lt ON gt lt OFF gt D N R 3D OFF SETUP MENU 1 ENTER EXIT SAVE YES IMAGE INVERSE lt ON gt lt OFF gt FREEZE lt ON gt lt OFF gt APERTURE 01 16 lt YES gt lt OFF gt lt M E gt SETUP MENU 2 ENTER ELIP lt IMAGE gt EXIT SET YES ADJUST MIN ANGL ANGLE ADJUSTER 40 lt 10 gt DEG 63 User s Manual Layer 1 Layer 2 Layer 3 Notes ADJUST MAX ANGL lt 080 gt lt 100 gt DEG EXIT SET YES SPEED BY ZOOM lt ON gt lt OFF gt AUTO CALI lt ON gt lt OFF gt PASSWORD lt ON
19. LARM SWITCH lt ON gt lt OFF gt OFF ALARM TYPE lt NO gt lt NC gt NC PRESET x SEQUENCE ALARM ACTION TOPAN ALARM SETTNG ENTER a PRESET POINT 001 256 SEQUENCE LINE 001 008 obi AUTOPAN LINE 001 004 CRUISE LINE 001 008 001 127 SEC DWELL TIME LADWAYGS ALWAYS EXIT YES DETECT SWITCH ON OFF OFF DETECT MODE lt MOTION gt MOTION BLOCK MODE lt NONE gt lt ON gt lt OFF gt NONE ALARM DETECT FRAME SET NONE MOTION 01 04 NONE FRAME DISABLE NONE MOTION 01 04 NONE THRESHOLD NONE MOTION 001 255 NONE EXIT YES WDR FUNCTION OFF PRIVACY SWITCH TRANSPARENCY ON OFF BLACK WHITE RED GREEN COLOR BLUE lt YELLOW gt lt MAGENT PRIVACY MASK A gt CENTER L R V CENTER D U SET MASK 01 16 SIZE 000 080 000 V SIZE 000 060 000 EXIT SAVE CLEAR MASK 01 16 EXIT YES TIME DISPLAY ON OFF OFF SET YEAR 00 99 SET MONTH 01 12 TIME SETTING ENTER SET DAY 01 31 SET HOUR 00 23 SET MINUTE 00 59 EXIT SAVE YES SCHEDULE SCHEDULE SWITCH lt ON gt lt OFF gt OFF POINT 01 32 01 HOUR lt 00 gt 23 00 MINUTE lt 00 gt lt 59 gt 00 NONE NO FUNCTION PRESET POINT PRESET oaea SEQUENCE LINE SEQUENCE T PA A AUTOPAN LINE MODE AUTOPAN ey CRUISE LINE CRUISE DE
20. LUE AUTO EXIT SAVE YES SHUTTER SPEED PAL lt 1 50 gt lt 1 10000 gt SEC Snes NTSC lt 1 60 gt lt 1 10000 gt SEC AE MODE EXIT SAVE YES is IRIS VALUE lt F1 6 gt EXIT SAVE YES BRIGHT VALUE AUTO SHUTTER SPEED PAL lt 1 50 gt lt 1 10000 gt SEC MANUAL NTSC lt 1 60 gt lt 1 10000 gt SEC IRIS VALUE lt F1 6 gt GAIN VALUE lt 3 gt dB lt 28 gt dB EXIT SAVE YES EXIT SAVE YES AUTO Auto White Balance INDOOR OUTDOOR WBC MODE ATW Auto tracing WBC R GAIN lt 000 gt 127 MANUAL B GAIN 000 127 EXIT SAVE YES SETUP MENU 1 ENTER ZOOM SPEED 8 8 DIGITAL ZOOM OFF OFF SLOW SHUTTER OFF OFF 2D N R lt ON gt OFF ON D N R 3D OFF ON EXIT SAVE YES IMAGE INVERSE OFF FREEZE lt ON gt lt OFF gt OFF APERTURE 01 16 07 18 User s Manual Layer 1 Layer 2 Layer 3 Default EXIT lt YES gt OFF FLIP lt IMAGE gt ORE EXIT SET YES ADJUST MIN ANGL m lt 10 gt 10 DEG ANGLE ADJUSTER ADJUST MAX ANGL 080 100 DEG EXIT SET YES SPEED BY ZOOM ON OFF OFF SETUP MENU2 ENTER AUTO CALI OFF OFF PASSWORD OFF OFF OSD AUTO CLOSE ka LE 20 S
21. Mini PTZ CAMERA ZC PT SERIES Indoor USER S MANUAL GOG User s Manual Preface The information given in this manual was current when published The company reserves the right to revise and improve its products All specifications are subject to change without notice Notice To work with the Mini PTZ Cameras any installer or technician must have the following minimum qualifications e basic knowledge of CCTV systems and components e A basic knowledge of electrical wiring and low voltage electrical hookups e A basic knowledge of network system setting e Have read this manual completely Copyright Under copyright laws the contents of this user manual may not be copied photocopied translated reproduced or reduced to any electronic medium or machine readable format in whole or in part without prior written permission of the company Important Information Before proceeding please read and observe all instructions and warnings in this manual Retain this manual with the original bill of sale for future reference and if necessary warranty service When unpacking your unit check for missing or damaged items If any item is missing or if damage is evident DO NOT INSTALL OR OPERATE THIS PRODUCT Contact your dealer for assistance Regulation This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interferen
22. RM DETECT main page FRAME DISABLE Select a frame to be canceled and press ENTER The selected frame will then be removed from the monitored field THRESHOLD The Threshold range is adjustable from 1 255 The smaller the value the more sensitive it is i e 1 highest sensitivity 255 lowest sensitivity EXIT Exit the ALARM DETECT menu and go back to the MAIN PAGE 3 to carry on setup of WDR function see 3 3 20 WDR FUNCTION User s Manual 3 3 20 WDR FUNCTION The Wide Dynamic Range WDR function is especially effective in solving indoor and outdoor contrast issues to enhance better image quality and video display It enables the PTZ Camera to catch detailed data from the dark part Indoor without any saturation from the bright part Outdoor NOTE The Backlight function will be turned off automatically when the WDR function is enabled because the WDR function has better effects than Backlight Compensation e ON Activate the WDR function by selecting this option In this mode the PTZ Camera will operate the WDR function automatically e OFF Deactivate the WDR function Exit the WDR FUNCTION menu and go back to the MAIN PAGE 3 to carry on setup of Privacy Mask MAIN PAGE 3 IR FUNCTION ALARM SETTING ALARM DETECT WDR FUNCTION PRIVACY MASK TIME SETTING SCHEDULE EXIT OSD 47 3 3 21 48 User s Manual PRIVACY MASK The Privacy Mask function aims to avoid any intrusive monitoring Users c
23. YSTEM RESET YES SYSTEM RESET DEFAULT SYSTEM YES EXIT YES EXIT YES ID DISPLAY lt ON gt OFF ON TITLE DISPLAY ON OFF OFF TITLE SETTING 01 16 01 PRESET SET lt 001 gt lt 256 gt ENTER PRESET PRESET RUN lt 001 gt lt 256 gt ENTER EXIT YES ENTER SEQUENCE LINE gt 8 1 SEQUENCE POINT 015 64 01 PRESET POS A SED 001 SEQUENCE ENTER SPEED 2 5i DWELL TIME 000 127 SEC 000 RUN SEQUNECE ENTER EXIT YES AUTOPAN LINE lt 1 gt 4 1 lt TO FIND START POINT TE TO FIND AUTOPAN ENTER EOT TAN lt TO SAVE gt DIRECTION RIGHT LEFT Right SPEED 01 04 01 RUN AUTOPAN EXIT CRUISE LINE lt 1 gt lt 8 gt 1 RECORD START ENTER CRUISE ENTER RECORD END ENTER RUN CRUISE ENTER EXIT ENTER HOME FUNCTION ON OFF OFF PRESET SEQUENCE SELECT MODE CRUISE PRESET POINT lt 001 gt lt 256 gt ENTER SEQUENCE LINE 001 008 T AUTOPAN LINE 001 004 CRUISE LINE 001 008 RETURN TIME lt 001 gt 128 MIN 001 GO ENTER EXIT YES IR FUNCTION THRESHOLD MID LOW AUTO EXIT SAVE YES MANUAL IR MANUAL ON OFF 19 User s Manual Layer 1 Layer 2 Layer 3 Default EXIT SAVE YES ALARM PIN lt 1 gt 85 1 A
24. Z Camera Package a Data Cable for Power Supply Video and RS 485 for AC 24V model PTZ Camera AT L GAZ Quick Guide 4 ee Woe NS Hard Ceiling Mount M3 Screw Fixing Plate CD Operation Manuals User s Manual 2 2 Switch Connector Definition Configuring the PTZ Camera s ID and communication protocol are required before connecting the analog camera to other devices The switches used for configuring these settings are located on the bottom of the PTZ Camera Additionally the 22 Pin Connector for Data Cable connection and ISP Connector for firmware upgrade kit connection are located on the back plate of the PTZ Camera Please refer to the diagrams and tables accompanied with for use of each switch connector Camera Control Protocol Switch Communication Switch None 22 Pin Connector ID Switch Reserved ISP Connector for FW upgrade The ID and Protocol numbers of an analog camera are set with a 10 bit and 6 bit dip switch respectively using binary system For switch configuration details please refer to Appendix B Switch Settings Index Table 11 2 3 User s Manual Communication Switch Setting The PTZ Camera s communication switches are specified in the table below Communication Switch RS 485 Setting
25. able from 1 to 4 10 45 degree sec RUN AUTOPAN After all setting related to auto pan are completed select this item to execute the Auto pan function EXIT Exit the AUTOPAN setup menu go back to the MAIN PAGE 2 to carry on setup of cruise User s Manual MAIN PAGE 2 ID DISPLAY TITLE DISPLAY TITLE SETTING PRESET SEQUENCE AUTOPAN CRUISE HOME SETTING NOTE Users could execute the auto pan function through a keyboard Please refer to the control keyboard s quick guide for further information 3 3 15 CRUISE CRUISE is a route formed with manual operation through adjusting pan and tilt position which can be stored and recalled to execute repeatedly CRUISE CRUISE LINE RECORD START RECORD END RUN CRUISE EXIT CRUISE LINE There are eight sets of Cruise line built in a PTZ Camera Using LEFT RIGHT direction keys to select a line first and then follow the steps below to start recording the cruise path RECORD START Follow the description below to record the CRUISE path 1 Rotate the PTZ Camera to a desired view area for some protocols users may need to do it before entering the OSD and press ENTER to build the cruise path using the joystick on the control device The percentage of the memory buffer will be displayed on the screen 2 Pan and tilt the PTZ Camera to form a path NOTE Beware of the memory size when building a cruise path Once the buffer percentage reaches 100 recording
26. able the flip function NOTE To make the PTZ Camera tilt between a specific range A such as 10 to 100 please go to ANGLE ADJUSTER see next section to set the angle range of tilt Otherwise the camera will tilt 90 as the default setting ANGLE ADJUSTER The item is for adjusting the camera view angle The range of view angle is between 10 and 100 ANGLE ADJUSTER ADJUST MIN ANGLE 10 DEG ADJUST MAX ANGLE 100 DEG EXIT SET YES SPEED BY ZOOM If the item is set to lt ON gt the pan tilt speed will be adjusted by internal algorithm when zooming automatically The larger zoom ratio leads to the lower rotation speed AUTO CALI Auto Calibration There are one horizontal and one vertical infrared ray check points in each PTZ Camera When the PTZ Camera s position is moved during installation or maintenance the relative distance between the original set point and the check point could be changed Enable the Auto Calibration function the camera will automatically detect the distance change and reset the point back to the original position PASSWORD The administrator can activate OSD Password function for security concerns Once the function is turned on users are required to enter the password every time when accessing to the OSD menu The Password setting menu is shown below 29 30 User s Manual NEW PASSWORD __ CONFIRM PASSWORD 0123456789 lt SAVE EXIT The password setting proc
27. al Zoom Digital Slow Shutter Backlight Compensation Auto Focus Auto White Balance Auto Gain Control Auto Iris Control Auto Calibration Removable IR Cut Filter Minimum Illumination 0 1 Lux 0 01 Lux B W Wide Dynamic Range 2D 3D Noise Reduction User s Manual 1 2 Product Application Connect PTZ Cameras to other devices as shown in the diagram to complete a video surveillance solution RS 485 RS 485 RS 485 Video T m w m Main Monitor EN 4 Call Monitor Repeater Dome Camera Dome Camera Dome Camera Switch Quad Mux DVR Video Video Video RS 485 RS 485 NOTE To extend the network distance up to 1 2 km 4000 feet and to A protect the connected devices it is highly recommended to place a repeater at the mid point However a repeater may be needed in the network distance less than 1 2 km if the used cables are not the CAT 5 24 gauge cables see 2 7 RS 485 Connector Definition Analog Refer to the repeater s manual for detailed information 2 1 10 User s Manual Connecting the Mini PTZ Camera Please refer to the following sections to connect set and operate the PTZ Camera In order to control the camera basically a control keyboard or other control device is required Package Content Before proceeding please check the box contains the items listed here If any item is missing or has defects DO NOT install or operate the product and contact your dealer for assistance Mini Indoor PT
28. an adjust the camera view position using the joystick and adjust the mask size and area via the direction keys on the control keyboard When setting a mask it is suggested to set it at least twice bigger height and width than the masked object The PTZ Camera will assume the center of the selected view as an starting point and the joystick will be locked as users enter the SET MASK menu mentioned later Refer to the following description for setting privacy masks NOTE The Image Flip function and the Image Inverse function will be disabled automatically while the Privacy Mask function is enabled The available area for setting a privacy mask is restricted within tilt angle 70 degrees Maximum 8 masks can be displayed in one scene All the settings are described as the following PRIVACY MASK MENU PRIVACY SWITCH TRANSPARENCY COLOR SET MASK CLEAR MASK EXIT e PRIVACY SWITCH Users can enable or disable the Privacy Mask function through this item Set this item to lt ON gt before configuring mask zones e TRANSPARENCY The color of privacy mask can be set as transparent Select lt ON gt to display transparent masks e COLOR The color of privacy mask can be set through this item The available colors are black white red green blue cyan yellow and magenta SET MASK Use the control device to move the PTZ Camera to the area where you want to set a mask Press ENTER to enter the SET MASK menu The PTZ Camera will
29. ce and 2 this device must accept any interference received including interference that may cause undesired operation User s Manual This symbol on the product or on its packaging indicates that this product shall not be treated as household waste in accordance with Directive 2002 96 EC Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By proper waste handling of this product you ensure that it has no negative consequences for the environment and human health which could otherwise be caused if this product is thrown into the garbage bin The recycling of materials will help to conserve natural resources For more details information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product Compliance is evidenced by written declaration from our suppliers assuring that any potential trace contamination levels of restricted substances are below the maximum level set by EU Directive 2002 95 EC or are exempted due to their application User s Manual Cautions Handle the camera carefully Do not abuse the camera Avoid striking shaking etc The camera could be damaged by improper handing or storage Installing electricity wiring carefully Ask qualified personnel of electrical wiring for the installation Please note
30. djustable alarm parameters are listed below ALARM SETTING ALARM PIN ALARM SWITCH ALARM TYPE ALARM ACTION PRESET POINT DWELL TIME EXIT e ALARM PIN The PTZ Camera provides 8 alarm inputs and 1 relay output 1x and 1x N C Select an alarm pin which you want to set its alarm related parameters and then set its alarm related parameters in the Alarm Setting menu For alarm pin definitions please refer to section 2 6 22 Pin Connector Definition or the installation guide NOTE If two or more alarm pins are triggered at the same time A smaller alarm pin number will have higher priority of being handled For example if Alarm 1 and Alarm 3 are triggered simultaneously only Alarm 1 will actually be handled e ALARM SWITCH The item is used to enable or disable the selected alarm pin function Use the left right direction keys on the control keyboard to change the setting 42 User s Manual ALARM TYPE There are two kinds of alarm types Normal Open and Normal Close which are illustrated as below Select an alarm type that corresponds with the alarm application O Alarm In Normal Open oe Normal Close ALARM ACTION The alarm actions include PRESET SEQUENCE AUTOPAN and CRUISE functions Select one of these modes so that certain action will be executed when an alarm is triggered Use the right direction key of the control keyboard to select a particular action mode and the items listed below will cha
31. edure is like the following STEP 1 Choose a number with direction keys and then press the CAMERA MENU gt key ENTER to input For example 0 CAMERA MENU gt 1 CAMERA MENU gt 2 CAMERA MENU gt 3 CAMERA MENU gt PASSWORD 0123 STEP 2 In the second line enter the same password again to confirm the setting STEP 3 Move the cursor to SAVE and press CAMERA MENU gt to save the setting STEP 4 Move the cursor to EXIT and press CAMERA MENU to exit the password setting page If OSD Password function is enabled when press the CAMERA MENU key to enter the OSD menu the password request message will be displayed as shown below Please enter the password press ENTER and then access to the OSD main menu PLEASE ENTER PASSWORD 0123456789 lt ENTER EXIT OSD AUTO CLOSE Users can specify the duration for OSD menu to stay on the screen Time selection ranges from 5 30 seconds To keep the OSD menu stay on the screen please set this option to OFF SYSTEM RESET Two types of system reset can be implemented under this item SYSTEM RESET Select this function for system reboot Press ENTER and system reboot will start up User s Manual 3 3 9 3 3 10 DEFAULT SYSTEM This function allows users to restore the camera to its factory default state Press ENTER and reset will start up e EXIT Exit the SETUP MENU 2 and go to the MAIN PAGE 2 to carry on setting other fu
32. era to do endless panning by setting the start point the same as the end point START POINT Follow the description below to set the start position of the AUTOPAN path 1 Move the cursor to START POINT and press ENTER while the item lt TO FIND gt is flashing Then the item will turn lt TO SAVE gt automatically 35 36 User s Manual 2 Move the PTZ Camera to a desired position and press ENTER to save the position as the start point the cursor will move to lt END POINT gt automatically Ensure setting the end point to complete auto pan setting NOTE The tilt and zoom values of the start point will be recorded and fixed for the selected auto pan line END POINT Users are able to set the end point after the start point is defined Pan the PTZ Camera to another position and press ENTER to save the position as the end point DIRECTION The item is for setting the AUTOPAN direction of the PTZ Camera The camera will start to pan clockwise from the start point to the end point if your selection is RIGHT and then return to the start point The PTZ Camera will start to pan anti clockwise from the start point to the end point if your selection is LEFT Refer to the diagram below Start Point LEFT RIGHT LEFT RIGHT anti clockwise PTZ Camera clockwise B888 End Point SPEED The item is for defining the PTZ Camera rotation speed while running auto pan The speed is adjust
33. f your surveillance system Generally use one protocol even the devices are provided from different manufacturers Please refer to the table below for all supported protocols with their matching switch numbers and baud rate and choose a protocol for your PTZ Camera Switch No Protocol Baud Rate 00 VCL 9600 01 Pelco D 2400 02 Pelco P 4800 04 Chiper 9600 05 Philips 9600 07 DSCP 9600 08 AD422 4800 09 DM P 9600 11 Pelco D 4800 12 Pelco D 9600 13 Pelco P 2400 14 Pelco P 9600 15 JVC 9600 21 Kalatel 485 9600 22 Kalatel 422 4800 23 Panasonic 19200 Use the 6 bit dip switch Camera Control Protocol Switch to set your camera s control protocol and its baud rate If select protocol Pelco D which is of switch no 01 and baud rate 2400 for instance set the SW 1 to ON with the rest to OFF as shown below 001 For switch configuration details please refer to Appendix B Switch Settings Index Table User s Manual 2 6 22 Pin Connector Definition A Data Cable is shipped with the PTZ Camera for a quick installation for demo or testing usage Additionaly the PTZ Camera s 22 pin connector definition will also be specified later For more information about RS 485 connector see 2 7 RS 485 Connector Definition The PTZ Camera s Data Cable is illustrated as shown below Il i AC 24V 5 GND Power Input AC 24V 2
34. gt lt OFF gt OSD AUTO CLOSE a dapi SYSTEM RESET YES SYSTEM RESET DEFAULT SYSTEM YES EXIT YES EXIT YES ID DISPLAY OFF TITLE DISPLAY ON OFF TITLE SETTING 01 16 PRESET SET lt 001 gt lt 256 gt PRESET PRESET RUN lt 001 gt lt 256 gt EXIT YES SEQUENCE LINE 1 8 SEQUENCE POINT 01 64 PRESET POS En ud SEQUENCE ENTER SPEED T Es DWELL TIME 000 127 SEC RUN SEQUNECE ENTER EXIT YES AUTOPAN LINE lt 1 gt 45 FIND START POINT ES FIND AUTOPAN ENTER m kika kl TO SAVE DIRECTION RIGHT LEFT SPEED 01 04 RUN AUTOPAN EXIT CRUISE LINE lt 57 lt 8 gt RECORD START ENTER CRUISE ENTER RECORD END ENTER RUN CRUISE ENTER EXIT ENTER HOME FUNCTION lt ON gt lt OFF gt PRESET SEQUENCE SELECT MODE SEA CRUISE PRESET POINT lt 001 gt lt 256 gt E LL ENTER SEQUENCE LINE 001 008 AUTOPAN LINE 001 004 CRUISE LINE 001 008 RETURN TIME 001 128 MIN GO ENTER EXIT YES ios THRESHOLD MID HI LOW RUTHIN EXIT SAVE YES IM IR MANUAL ON OFF EXIT SAVE YES ALARM SETTNG ENTER ALARM PIN lt 15 85 ALARM SWITCH lt ON gt lt OFF gt ALARM TYPE NO NC ALARM ACTION PRESET SEQUENCE 64 User s Manual
35. item to run the preset point PRESET RUN Select the preset point that you want to execute After pressing ENTER the camera will turn to the appointed point EXIT Exit the PRESET menu and go back to the MAIN PAGE 2 to carry on setup of sequence MAIN PAGE 2 ID DISPLAY TITLE DISPLAY TITLE SETTING PRESET SEQUENCE AUTOPAN CRUISE HOME SETTING NOTE Users could set preset points through a keyboard Please refer to the control keyboard s quick guide for further information 33 User s Manual 3 3 13 SEQUENCE The function executes pre positioning of the pan tilt Zoom and focus features in a certain sequence for a camera Before setting this function users must preset at least two preset points SEQUENCE SEQUENCE LINE SEQUENCE POINT PRESET POSITION SPEED DWELL TIME RUN SEQUENCE EXIT e SEQUENCE LINE There are eight sets of sequence lines built in the PTZ Camera Using LEFT RIGHT direction keys to select a line first and then set its sequence points e SEQUENCE POINT Up to 64 points can be specified for each sequence line The sequence points represent order of the preset points that the PTZ Camera will automatically run The following setup items including PRESET POSITION SPEED and DWELL TIME will influence how the camera runs through each sequence point e PRESET POSITION Users can assign a specific preset position to the selected sequence point with this item e SPEED Users can set the
36. n a screen in the range from 2000 K to 10000 K 25 3 3 7 26 User s Manual e MANUAL In this mode users can change the White Balance value manually R gain and B gain are adjustable and range from 0 to 127 WBC MENU R GAIN 50 B GAIN 50 EXIT SAVE YES SETUP MENU 1 The SETUP MENU 1 is shown below SETUP MENU 1 ZOOM SPEED 8 DIGITAL ZOOM SLOW SHUTTER D N R IMAGE INVERSE FREEZE APERTURE EXIT The zoom speed of the PTZ Camera is fixed Value 8 Users could choose whether to activate functions including Digital Zoom Slow Shutter Noise Reduction Image Inverse and Image Freeze Refer to the following description for use of each function e DIGITAL ZOOM With this item users can enable or disable the 12x Digital Zoom The Digital Zoom will start to activate after the full Optical Zoom level is reached Maximum 12x digital zoom function is allowed to be enabled The default setting is NOTE The difference between optical and digital zoom is that A optical zoom uses the lens within the camera to draw the image closer via zoom in or out to achieve the desired effect Optical zoom remains the same resolution of the zoomed image quality On the other hand Digital zoom takes a portion of image and expands that image to the full size of the image the image quality will be reduced e SLOW SHUTTER The shutter speed determines how long the image sensor is exposed to light The PTZ Camera will automa
37. nctions MAIN PAGE 2 ID DISPLAY TITLE DISPLAY TITLE SETTING PRESET SEQUENCE AUTOPAN CRUISE HOME SETTING ID DISPLAY Users are allowed to choose whether the PTZ Camera s ID will be displayed on the monitor to identify each PTZ Camera For PTZ Camera s ID setting please refer to section 2 4 ID Setup Analog Model e ON Display the ID of the selected PTZ Camera on the right bottom of the monitor screen e OFF Hide the ID of the selected PTZ Camera TITLE DISPLAY Users are allowed to name a certain view area and display its title for easy recognition With this item users can choose to display or not to display the titles set in advance e ON A title set for certain view will be displayed when the PTZ Camera stays in the view area e OFF When the TITLE DISPLAY is set OFF no title will be displayed on the screen even titles are set in advance 31 3 3 11 32 TITLE Up to 16 User s Manual SETTING zone titles can be set with maximum 20 characters for each title Follow the steps to set a camera title STEP 1 for it STEP 2 STEP 3 STEP 4 STEP 5 STEP 6 Operate the PTZ Camera to a view area where you want to set a title Turn on the OSD and go to the MAIN PAGE 2 to select lt TITLE SETTING gt Select a number to represent the view area Press the lt CAMERA MENU gt key ENTER to go into the editing page TITLE SETTING 01 0123 4 5 6 7 8 9 ABCDEF GH
38. nge in accordance with your selected alarm action Additionally when an alarm is triggered there will be a flash warning notice ALARM displayed in the upper right corner of the screen PRESET POINT Select a Preset Point where the PTZ Camera should go when an alarm pin is triggered The preset point s should be set prior either in the PRESET setup menu or through the keyboard SEQUENCE LINE Select a Sequence Line that the PTZ Camera should execute when an alarm pin is triggered The sequence line s should be defined prior either in the SEQUENCE setup menu or through the keyboard AUTOPAN LINE Select an Auto pan Line that the PTZ Camera should execute when an alarm pin is triggered The Auto pan Line s should be defined prior either in the AUTOPAN setup menu or through the keyboard CRUISE LINE Select a Cruise Line that the PTZ Camera should execute when an alarm pin is triggered The Cruise Line s should be defined prior either in the CRUISE setup menu or through the keyboard 43 44 User s Manual DWELL TIME The DWELL TIME is duration of executing an alarm action If select the PRESET mode is selected when alarm takes place the PTZ Camera will go to the selected preset position and stay there for a user defined period of time 1 127seconds Always when alarm takes place If select other modes SEQUENCE AUTOPAN CRUISE have been selected the camera will keep executing the selected mode DWELL TIME ALWAYS until alarm
39. oHS Specifications are subject to change without notice 54 User s Manual Appendix B Switch Settings Index Table Please refer to the switch settings below for Mini PTZ Camera s ID and protocol setup Camera ID Setup SWITCH SETTING O AN 5 o d a d ad oo oo N O TUF ON O AF WO ND 25 55 User s Manual SWITCH SETTING 56 User s Manual SWITCH SETTING 57 User s Manual SWITCH SETTING 58 User s Manual SWITCH SETTING 59 User s Manual SWITCH SETTING 60 User s Manual SWITCH SETTING 61 User s Manual Protocol Setup SWITCH SETTING Protocol 62 User s Manual Appendix C OSD Menu Notes The following OSD menu table is provided for users to record various camera settings Item Layer 1 Layer 2 Layer 3 Notes lt ENGLISH gt lt PORTUGUESE gt lt SPANISH gt lt FRENCH gt GERMAN lt ITALIAN gt CAMERA SON OFF BACKLIGHT lt ON gt lt OFF gt AF MODE lt NORMAL gt Z TRIG gt lt PTZ TRIG gt FOCUS ne EXIT SAVE YES MANUAL EXPOSURE odi ME VALUE lt 10 5dB gt EXIT SAVE YES BRIGHT VALUE SHUTTER SPEED AUTO
40. of the path will stop 37 38 User s Manual e RECORD END The cursor will be moved to RECORD END while building the cruise line when the setting is completed press ENTER to save the path e RUN CRUISE After Cruise setting is completed select this item to execute the Cruise function e EXIT Exit the CRUISE setup menu go back to the MAIN PAGE 2 to carry on setup of home setting MAIN PAGE 2 ID DISPLAY TITLE DISPLAY TITLE SETTING PRESET SEQUENCE AUTOPAN CRUISE HOME SETTING NOTE Users could execute the cruise function through a keyboard Please refer to the control keyboard s quick guide for further information User s Manual 3 3 16 HOME SETTING Users are able to set an operation mode to ensure constant monitoring if the PTZ Camera idles for a period of time the selected function will be activated automatically HOME function allows constant and accurate monitoring to avoid the PTZ Camera stopping or missing events HOME SETTING HOME FUNCTION SELECT MODE PRESET POINT RETURN TIME HOME FUNCTION The item is used to enable or disable the HOME function Use the left right direction keys of the control keyboard to change the setting SELECT MODE Select one of the modes that the PTZ Camera should execute when HOME function is enabled and the RETURN TIME is up The options include lt AUTOPAN gt lt SEQUENCE gt CRUISE lt PRESET gt Use the left right direction keys on
41. pe gently User s Manual Never face the camera towards the sun Do not aim the camera at bright objects Whether the camera is in use or not never aim it at the sun or other extremely bright objects Otherwise the camera may be smeared or damaged User s Manual 1 2 3 Table of Contents OYE NEW ii isi ai eke ii ki l a eee eee n ik ka er 7 1 1 8 1 2 ko ad gei e 9 Connecting the Mini PTZ 10 2 11 Content TT en 10 2 2 Switch Connector Definition 11 2 3 Communication SWVC TS UNG Me m 12 24 WD mr 13 2 5 Camera Control Protocol 5 14 2 6 22 Pin Connector 15 2 7 RS 485 Connector 16 Operation and Configuration 2 taa sx aka 17 3 1 OSD Display Format NOE OT Sq MEET 17 3 2 OSD 18 sees ue E 22 331 E cB C crm 22 3 3 2 DEFAULT CAMERA ie iria iate prid atia EA CERE k ki tk 23 3 3 3 BACKUGH p M 23 334 Le 010 cc 23 3 3 9 AE MODE wt ty de ti c S 24
42. ration the available languages include English French German Italian Portuguese and Spanish As you select a language with the arrow keys on the Control Keyboard the OSD menu will automatically change to the language you have selected The default language is lt ENGLISH gt MAIN PAGE 1 LANGUAGE DEFAULT CAMERA BACKLIGHT FOCUS AE MODE WBC MODE SETUP MENU 1 SETUP MENU 2 User s Manual 3 3 2 3 3 3 3 3 4 DEFAULT CAMERA The item is for restoring the camera settings including Backlight Focus AE WBC Digital Zoom Slow Shutter Image Inverse and Aperture to factory defaults Once any one of the parameters mentioned above is modified The DEFAULT CAMERA item will become lt OFF gt automatically Select lt ON gt to recall these camera parameters to default settings BACKLIGHT The Backlight Compensation function prevents the center object from being too dark in surroundings where excessive light is behind the center object Set this item to lt ON gt the center object will be brightened in contrast to the edge of the picture where backlight would most likely be located FOCUS The PTZ Camera s focus can be operated in two modes Manual Focus mode and Auto Focus mode e AUTO There are three options available for the AF Mode including Normal mode Zoom Trigger Z TRIG mode and PTZ Trigger PTZ TRIG mode The submenu of AF Mode is shown below AF MODE NORMAL EXIT SAVE YES Normal Mode
43. rcuit will function automatically in cooperating with IRIS to get consistent exposure output The IRIS value is fixed at f1 6 Manual In the mode users can adjust shutter speed 1 10000 1 50 for PAL 1 10000 1 60 for NTSC and gain value 3dB 28dB for optimized video output EXIT Exit the AE MODE menu and go back to the Main Page 1 to continue to User s Manual set the WBC mode MAIN PAGE 1 LANGUAGE ENGLISH DEFAULT CAMERA OFF BACKLIGHT OFF FOCUS AUTO AE MODE ENTER WBC MODE AUTO SETUP MENU 1 ENTER SETUP MENU 2 ENTER 3 3 6 WBC MODE A digital camera needs to find reference color temperature which is a way of measuring the color of a light source for calculating all the other colors The unit for measuring this ratio is in degree Kelvin K You can select one of the White Balance Control modes according to the installation condition The following table shows the color temperature of some light sources Light Sources Color Temperature in K Cloudy Sky 6 000 to 8 000 Noon Sun and Clear Sky 6 500 Household Lighting 2 500 to 3 000 75 watt Bulb 2 820 Candle Flame 1 200 to 1 500 e AUTO In this mode white balance works within its color temperature range This mode computes the white balance value output using color information from the entire screen e INDOOR 3200 K Base mode e OUTDOOR 5800 K Base mode e ATW Auto Tracing White Balance The PTZ Camera takes out the signals i
44. support automatic operations It is ideal for all surveillance requirements in hotels department stores intelligent buildings amusement parks parking lots factories hospitals schools stations etc The Mini PTZ Camera contains various solutions for low light and high contrast conditions For example a bright background or shade can result in the subject of the image appearing darker The backlight compensation function gives a bright and beautiful image The Mini PTZ Camera supports one cabling for easy installation and can be integrated with various digital surveillance products such as DVRs Control Keyboards and various sorts of accessories for a total surveillance solution The camera is incorporated with multiple protocols DynaColor Pelco VCL Philips etc to enhance powerful connectivity 1 1 User s Manual Product Features Precise and Accurate Mini PTZ Camera Performance High Resolution 540 TV lines Preset Speed up to 400 sec Preset Accuracy of 0 225 360 Endless Pan Proportional Pan amp Tilt Speed Preset Positions Auto Pan Sequence Cruise Auto Calibration Digital Mechanical Image Flip 180 Dynamic PTZ Camera Applications Schedule function Multiple built in protocols Extraordinary lightweight design for easy installation Vandal proof dome cover Optional Flexible indoor mountings 16 Privacy Masks Motion Detection Superior Camera Image Quality 12x Optical Zoom 12x Digit
45. ted as follows NONE No action will be executed for the schedule if select the item PRESET Users can select the PRESET mode as an action carried out in a schedule point SEQUENCE Users can select the SEQUENCE mode as an action carried out in a schedule point AUTOPAN Users can select the AUTOPAN mode as an action carried out in a schedule point 51 3 3 24 52 User s Manual CRUISE Users can select the CRUISE mode as an action carried out in a schedule point IR FUNC IR Function If the IR function mode is selected the AUTO IR FUNCTION will be activated for a schedule point e SCHEDULE RESET Users can reset the whole schedule with the item e SCHEDULE EXIT Exit the SCHEDULE menu and go back to the MAIN PAGE 3 EXIT OSD To exit the OSD setup menu users can either select this item on the bottom of MAIN PAGE 3 or press the ESC key on the control keyboard User s Manual Appendix A Technical Specification Items Indoor Mini PTZ Camera CAMERA CCD Sensor 1 4 EXview CCD Optical Zoom 12x Digital Zoom 1x 12x variable Effective Pixels idis PAL 440k Horizontal Resolution 540 TVL Scanning System NTSC PAL Synchronization Internal Line Lock Video Output 1 0 Vp p 75 O BNC Minimum Illumination 0 1 lux 0 01 lux B W Focal Length 3 8 45 6 mm Focus Mode Auto Manual White Balance Auto Manual Indoor Outdoor
46. that input electricity to the unit is at tolerance of DC 12V AC 24V 10 The camera is capable of surge protection ensure AC power model unit grounded appropriately against damage of heavy current or electric shock Do not disassemble the camera To prevent electric shock do not remove screws or covers There are no user serviceable parts inside Ask a qualified service person for servicing Do not block cooling holes on the bracket This camera has a cooling fan inside Blocking the cooling holes leads to build up heat of the camera and may cause malfunction Do not operate the camera beyond the specified temperature humidity or power source ratings Use the indoor PTZ Camera under conditions where temperature is between 0 C 40 C 32 F 104 F and the outdoor camera under conditions where temperature is between 30 C 45 C 22 F 113 F and humidity is below 90 Do not expose the indoor PTZ Camera to rain or moisture or try to operate it in wet areas The indoor PTZ Camera is designed for indoor use or locations where it is protected from rain and moisture Turn the power off immediately if the camera is wet and ask a qualified service person for servicing Moisture can damage the camera and also create the danger of electric shock Do not use strong or abrasive detergents when cleaning the camera body Use a dry cloth to clean the camera when it is dirty In case the dirt is hard to be removed use a mild detergent and wi
47. tically adjust the shutter speed basing on the light condition of the operating environment With Slow Shutter User s Manual function users can see clear image in low light conditions under 0 1 lux DIGITAL NOISE REDUCTION D N R With 2D 3D Noise Reduction the processor analyzes pixel by pixel and frame by frame to eliminate environmental noise signal so that the highest quality image can be produced even in low light conditions In comparison with 2D D N R 3D D N R generates better denoising effects IMAGE INVERSE Users can select lt ON gt to make the displayed image inversed vertically and horizontally see the figures shown below Occasions to employ the function include conferences demonstration testing etc The default setting is lt OFF gt When this function is enabled the preset mask s will be set off automatically Application Users can see the displayed images as shown below when a PTZ Camera is placed on the desk top in a conference for instance IMAGE INVERSE ON FREEZE Freeze function allows to hold the image while the camera is moving between preset positions such as in PRESET see section 3 3 12 and SEQUENCE see section 3 3 13 modes For example when the PTZ Camera is manipulated to run from point A to point B if the Freeze function is activated the first view that users would see is point A Then the next view would directly change to point B without displaying the moving path AP
48. tion zone so called Frame When motion is detected within a defined frame a flash warning notice MOTION will display in the upper left corner of the screen Total four frames can be set Select a frame using the right left keys on the keyboard and press ENTER key to enter the frame s submenu as shown below FRAME SET 1 LEFT LIMIT L R TOP LIMIT D U H SIZE 000 V SIZE 000 MODE PRESET PRESET POINT 001 DWELL TIME 001 SEC EXIT YES 45 46 User s Manual LEFT LIMIT Move the frame right left using the right left keys on the keyboard TOP LIMIT Shift the frame up down using the right left keys on the keyboard H V SIZE Adjust the frame size via changing H V size value using the right left keys on the keyboard MODE Assign a trigger action for a motion detection frame Options include PRESET SEQUENCE AUTOPAN and CRUISE When motion is detected within a frame the PTZ Camera will execute the specific trigger action DWELL TIME The DWELL TIME is duration of executing a trigger action If select the PRESET mode when motion is detected the PTZ Camera will go to the selected Preset position and stay there for a user defined period of time 1 127 seconds Always If select other modes SEQUENCE AUTOPAN CRUISE the PTZ Camera will keep executing the selected mode DWELL TIME ALWAYS until it is interrupted by commands sent from a connected control device EXIT Exit the FRAME setting page and go back to ALA
Download Pdf Manuals
Related Search