Optical Disc Laminator
Contents
1. Disc Printing Printer M Use Laminator Move To Laminator Calibrate M Minimize Print Dialog Cancel 8 Lower the disc to the Laminator Tray Position as follows a Press and hold the Sequence and Pick buttons simultaneously for 5 seconds to enter calibration mode The LEDs on the front of the DuplicatorMAX will flash back and forth indicating that the unit is in calibration mode Press Simultaneously Until LEDs Toggle Optical Disc Laminator Connectivity Guide 5 lt a b While the LEDs are flashing press the Pause button The Picking Mechanism will lower to the Laminator Tray Position Press Pause to Lower Mechanism to Laminator Tray Position c Adjust the Laminator Tray forward and back by loosening the adjusting screws located towards the front of the stand d For left to right adjustment nudge the Picker Mechanism left by pressing the Pause Button or nudge it right by pressing the Sequence Button End Calibration Nudge Picking Mechanism Right Counter Clockwise Nudge Picker Mechanism Left Clockwise e Once the Picking Mechanism and Disc are perfectly aligned press the Pick Button to end calibration 6 Optical Disc Laminator Connectivity Guide J f Tighten the Adjusting Screws on the front of the Laminator Stand to lock the stand in position 9 You have now calibrated your Laminator to the Duplicator MAX and are ready to produce discs D CREATING2. DISCS WITH YOUR DUPLICATOR MAX IN PRIMO Laminating your disc jobs is very simple This is done as follows 1 From the Main Application Screen click Robotics then Options Enable the Use Laminator checkbox as shown Duplicator Options Services Robotic Control Control Port x Check Communications Disc Printing Printer F Use Laminator Move To Laminator Calibrate M Minimize Print Dialog E Cancel 2 Set up your print and record job as you normally would per the instructions in the Duplicator MAX User Manual 3 Click the Red Circle Record button to start your job E CONNECTING THE LAMINATOR TO YOUR DUPLICATOR XL PRO Your Laminator connects easily to Duplicator Pro and Duplicator XL duplicators There are two possible configurations Automated Stand Alone Mode and Full Production Mode Automated Stand Alone Operation allows you to use the Laminator in place of a CD Printer You can then laminate pre printed discs without having to connect the Duplicator or Laminator to a PC Full Production Mode allows you to record print and laminate discs all in one operation Optical Disc Laminator Connectivity Guide 7 lt a The Laminator is positioned at the front left corner of the Duplicator The optional Duplicator XL Pro Laminator Stand is needed for both of these configurations The stand is shown here STAND ALONE MODE The Automated Stand Alone Mode allows you to connect the Laminator to
3. side of the Duplicator If the Laminator Tray is not in the OUT position press the Laminate button to eject the Laminator Disc Tray Press the Sequence button on the front of the Duplicator until the Picker is over the Input Bin Press the Pick button on the front of the Duplicator to pick a disc Repeatedly press the Sequence button on the front of the Duplicator until the Picker Arm comes to rest over the Laminator s Disc Tray Press and hold the Pick button on the front of the Duplicator for 5 seconds The disc should automatically and hover just over the Laminator s Disc Tray Loosen the Laminator Tray s 4 adjusting screws and move the Laminator around until the disc in the Picker aligns properly with the Laminator s Disc Tray Once you are satisfied with the positioning tighten the screws Press the Pick button on the front of the Duplicator The disc will now be deposited into the Laminator s Disc Tray Press the Pick button a few more times to pick and place discs into the laminator tray ensuring the alignment is accurate 10 Optical Disc Laminator Connectivity Guide lt a 8 The Laminator is now aligned properly Once the Laminator s Heat Roller has achieved proper operating temperature indicated by a solidly lit Ready LED on the Laminator s Control Panel you are ready to laminate discs Load the input bin with discs and press the Laminate button Discs will be automatically picked from the input bin loaded into the lamin
4. svciviscisesacisecndeceatessasdatandacnschasvtsasssvebsenstacesteheasabecnsibecnees T chnical Supports c iicicsccagina E aE E MOOS gt QT iii Interactive Feature in this PDF Document There are interactive features that will allow you to jump to different locations within the document Each listing in the Table of Contents is interactive Place the cursor on either the words or the page number A small hand with a pointing finger icon appears Click on the line with the icon and the document will jump to that page If you want to return to the Table of Contents move the icon to the top of the page and click on the arrow marked TOC lt a THANK YOU Thank you for purchasing the Optical Disc Laminator Connectivity Kit This kit will allow you to use your Optical Disc Laminator in conjunction with the Pro XL and MAX versions of Optical Disc Duplicators This guide will explain the connection of the Laminator to these systems the installation of software and the running of disc jobs A UNPACKING AND INSPECTION While unpacking your Laminator Connectivity Kit make sure that all supplied accessories are included with your kit The following items are included e Laminator Stand Software Installer Disc USB Cable 6 Pin Mini Circular Cable Pro XL Stand only Warranty Statement Manual and other documentation B INSTALLING THE LAMINATOR SOFTWARE DRIVER When using the Laminator with a Primera Technol
5. 012004 510887 01 Optical Disc Laminator Connectivity Guide 2004 All rights reserved Notices The information in this document is subject to change without notice NO WARRANTY OF ANY KIND IS MADE WITH REGARD TO THIS MATERIAL INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE No liability is assumed for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material This document contains proprietary information which is protected by copyright All rights are reserved No part of this document may be photocopied reproduced or translated into another language without prior written consent Trademark Acknowledgments Windows is a registered trademark of Microsoft Corporation All other trademarks are the property of their respective owners Printing History Edition 1 0 510887 Copyright 2004 All rights reserved ii Table of Contents Optical Disc Laminator Guide Unpacking and Inspection ccccccessessesesseessesssseseesssessssesssseenseenesees Installing the Laminator Software Drive cece Connecting the Laminator to Your Duplicator 0 0 ccc Creating Discs with Your Duplicator MAX in Primo Connecting the Laminator to Your Duplicator XL Pro uu Stand Alone M de narsan ksi tite alta Full Production Mode iviiietescyiseapiinticsiaeietehsshbattaditia Gaede Troubleshooting
6. ator and deposited in the output bin when finished This will repeat until the Input Bin is empty NOTE If the Picking Mechanism will not pick a disc from the Laminator Tray make certain the Laminator is sitting on the Stand correctly The Laminator s Rubber Feet should be resting on the stand not in the four holes located on top of the stand 9 When the Input Bin is empty you will see the Ready LED on the Laminators Control Panel flashing slowly indicating a Disc Out error and the Pick LED on the Duplicator Control Panel will be flashing quickly If you wish to continue load the Input Bin with discs and press the Pick button on the Laminator FULL PRODUCTION MODE In Full Production Mode you connect the Laminator to the Duplicator XL or DuplicatorPro in addition to your printer This allows for the fully automated recording printing and laminating of your discs This will require more desk space than the Stand Alone Lamination configuration described in the previous section This mode is set up as follows 1 2 Install the Laminator Software as described in this manual Laminate a few discs in Stand Alone configuration as described in the Laminator User s Manual to ensure the Laminator is set up to properly laminate your discs Place the Laminator Stand in front and to the left of the Duplicator as shown Optical Disc Laminator Connectivity Guide 11 Oe 4 Place the Laminator on the stand The Laminator will n
7. ator Tray to be sure it is aligned properly NOTE If the Picking Mechanism will not pick a disc from the Laminator Tray make certain the Laminator is sitting on the Stand correctly The Laminator s Rubber Feet should not rest on the stand but in the four holes located on the top of the stand 7 The Laminator is now aligned properly Once the Laminator s Heat Roller has achieved proper operating temperature indicated by a solidly illuminated Ready LED on the Laminator s Control Panel you are ready to laminate discs Load the input bin with discs Optical Disc Laminator Connectivity Guide 13 lt a 8 From the Main Application Screen click Robotics then Options Select Lamination as shown Duplicator Options Services Robotic Control Control Port be Check Communications Disc Printing Printer M Use Laminator Move To Laminator Calibrate Minimize Print Dialog Cancel 9 Set up your print and record job as you normally would per the Duplicator XL Pro User s Manual 10 Click the red circle Record button to start your job 14 Optical Disc Laminator Connectivity Guide lt a F TROUBLESHOOTING Problem Resolution Will not Laminate I do not see an option in PrimoDVD to laminate discs The Overlaminate Film is not adhering properly to my discs there are patchy areas where the film is not sticking to the disc label The Overlaminate Film appears to be wrinkling with scratch like marks ap
8. do instail the software automatically Recommended O Install from a list or specific location Advanced Click Next to continue 2 Optical Disc Laminator Connectivity Guide Oe g You may see a notice like the one shown here stating that the Accent Disc Laminator has not passed Windows Logo Testing Click the Install Anyway button to continue installing the printer driver for your Laminator Hardware Installation t The software you are installing for this hardware e Printers has not passed Windows Logo testing to verify its compatibility with Windows xP Tell me why this testing is important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing Continue Anyway STOP Installation Once the driver has finished installing click the Finish button This will install an update to your PrimoDVD software and will reboot your system C CONNECTING THE LAMINATOR TO YOUR DUPLICATOR MAX Your Laminator connects easily to a DuplicatorMAX allowing for hands free printing recording and laminating of Optical Discs This configuration does require you to remove one bin bringing total capacity from 400 to 300 discs The optional DuplicatorMAX Laminator Stand is sh
9. eed to be placed on the stand with the Laminator s rubber feet resting in the four holes located on the top of the Stand as shown 5 Using the provided USB Cable connect the Laminator to your PC as shown 6 Align the Laminator s Disc Tray position for proper picking and placement of discs This is done as follows a Make certain the Laminator has power and is turned on b Load a disc into the Input Bin This is the Bin on the right side of the Duplicator 12 Optical Disc Laminator Connectivity Guide lt a c Ifthe Laminator Tray is not in the OUT position press the Laminate button to eject the Laminator Disc Tray d From the Main Application Screen click Robotics then Options e Enable the Use Laminator checkbox f Click the button labeled Move to Calibrate This will move the Picker Mechanism to the Laminator Tray position Duplicator Options Services Robotic Control Control Port Zi Check Communications Disc Printing Printer M Use Laminator Move To Laminator Calibrate J Minimize Print Dialog Cancel g Press and hold the Pick button on the front of the Duplicator for 5 seconds The disc should automatically and hover just over the Laminator s Disc Tray h Manually move the Laminator on its stand until the Laminator Disc Tray is aligned perfectly with the disc in the Picker Mechanism i Press the Pick button a few times to pick and place the disc in the Lamin
10. ogy Disc Duplicator it will be necessary to install a driver This driver will allow the PC to control the functions of your Laminator Because your Disc Laminator is a plug and play device do not connect the Laminator s USB cable to the PC until instructed to do so by the installer The driver is installed as follows a This installer will reboot your system so make sure all applications are closed Insert the Software Driver Install disc into your PC s CD ROM drive b The Installer Quick Start program should launch If it does proceed to step c If not please follow these steps e Click the Start button in the lower left hand side of the screen and then select My Computer from the menu e Double click the Disc Laminator Installer Icon c Choose the Duplicator you are using either Duplicator XL Pro or Duplicator MAX d You will now be prompted to install and update to Primo DVD that will allow you to print record and laminate unnatended Click Next to install the update Optical Disc Laminator Connectivity Guide 1 qa e Make certain the Laminator has been plugged into power and turned on NNS f Select Install Software Automatically and click Next Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install software for Primera Technology Inc If your hardware came with an installation CD lt 6 or floppy disk insert it now What do you want the wizard to
11. own here MAX Stand Adjustable Screws Optical Disc Laminator Connectivity Guide 3 Gea The following steps describe in detail how to connect the Laminator to your DuplicatorMAX a Connect the Laminator Stand to the left hand side of the DuplicatorMAX as shown b Remove the Input Bin closest to the Laminator Stand to make room for the Laminator s disc tray c Place the Laminator on the stand using the Locating Pegs to align the Laminator properly d Connect your Laminator to the PC using the provided USB Cable e The Laminator must now be aligned with the DuplicatorMAX Picker Mechanism This is done as follows 1 If the Laminator Tray is not in the OUT position press the Laminate Button on the Laminator to eject the tray Make certain the DuplicatorMax has been connected to the computer and is on and ready to use 2 Press the Sequence Button on the front of the DuplicatorMax until the picker mechanism is positioned over a bin containing discs 3 Press the Pick Button on the front of the DuplicatorMax to pick a disc 4 Launch PrimoDVD Pro 4 Optical Disc Laminator Connectivity Guide lt a 5 From the Main Application Screen click Robotics then Options 6 Enable the Use Laminator checkbox 7 Click the button labeled Move to Calibrate This will move the Picker Mechanism to the Laminator Tray position Duplicator Options Services Robotic Control Control Port bd Check Communications
12. pearing across the surface of the disc Check Power to the Laminator Make sure that the Ready LED is on and steady indicating the Laminator s Heat Roller has achieved normal operating Temperature In PrimoDVD click Robotics then Options You should see a Laminate check box If you do not see this option in the Robotic Options dialog box install the software on the install disc provided with your Laminator Stand There is an updater on this disc that will add this functional Increase the heat setting with the Heat Slide Bar on the Laminator s Control Panel Slide the Heat Setting one or two hash marks toward the front of the Laminator to increase the heat setting Decrease the heat setting with the Heat Slide Bar on the Laminator s Control Panel Slide the Heat Setting one or two hash marks toward the rear of the Laminator to decrease the heat setting G TECHNICAL SUPPORT If you have difficulties in operating your Laminator the procedures in this manual should in most cases solve the problem If you still have difficulty call Technical Support at the number listed on the insert in your Laminator suppy pack Optical Disc Laminator Connectivity Guide 15 Printed in the United States of America P N 510887
13. the Duplicator XL or DuplicatorPro without connecting either the Duplicator or Laminator to a PC This mode is used when you simply want to load the Duplicator with 100 printed discs and laminate them unattended The Laminator will take the place of a printer in this configuration Stand Alone Mode is set up as follows 1 Laminate a few discs in Stand Alone configuration as described in the Laminator User s Manual to ensure the Laminator is configured to properly laminate your discs 2 If present remove the Printer Stand and Printer from the back of the Duplicator 3 Make sure both the Power and Auxiliary Control Cable are connected to the Duplicator as shown 8 Optical Disc Laminator Connectivity Guide lt a 4 Connect the Laminator Stand to the back of the Laminator as shown There are two sets of holes on the underside of your Laminator Set the Laminator on the stand locating the smaller set of holes on the metal locating pegs on the Laminator Stand Make certain the Laminator s rubber feet are resting on the stand and not in the four large holes in the stand Optical Disc Laminator Connectivity Guide 9 lt a 6 Connect the Auxiliary Control Cable and Power Cable the Laminator as shown 7 Align the Laminator s tray position to the picker This is done as follows a b Make certain the Laminator has power and is turned on Load a disc into the Input Bin This is the Bin on the right
Download Pdf Manuals
Related Search