Home

Remote control systems

1. 30 seconds or press the programming button The chosen switch is saved Remote control resetting Press briefly and release the lateral programming button on the MHS FBM receiver less than 1 sec Three green LEDs one blue LED flash two times per second On the remote control press and release button to reset The LEDs flash 10 times then the button is reset To terminate the reset mode wait for 30 seconds or press the programming button Setting of maximum heating duration Press and hold the lateral button for more than 2 seconds After 2 seconds the blue LED will briefly flash three times the blue LED flashes every second the green LEDs show the set time Each short press amp release of the lateral button on the receiver will increment the heating duration according to the built in Time Code see below The heating duration can also be changed by pressing the button that has been previously programmed After 30 seconds following the last press amp release the programming will end and the chosen Time Code set is saved Time Code Can be set from minimum 30 minutes to maximum 12 hours 7 settings to choose from 0 5 1 2 3 4 8 12 hours 9 6 0 Operation Standby operation ON Heat output settings Party mode To launch the Party Mode General OFF Test operation without transmitter heating off blue LED lit press the ON button heat output is set up on power 3 full pow
2. M receiver Electronic smog and radio signals Many people are worried about the possible consequences for their health of the electronic smog created by the countless electrical fields due to the many wireless devices we are surrounded by Manufacturers hence worry about possible claims for damages based on such health related harm Nevertheless the need for wireless devices keeps increasing quickly Therefore we had the standard intensity of the electro magnetic fields created by our radio receivers measured by ECOLOG under in situ usage conditions ECOLOG is the German Institute for Socio Ecological Research and Education What are the results 1 The Enocean Radio system emits one hundred times less intensive high frequency fields than conventional light switches the latter s high frequency fields are produced through the characteristic sparkling switching process 2 The intensity of the quick high frequency emissions of the EnOcean radio switch are up to 10 000 times fewer than the permanent high frequency emissions of the mobile phone network stations in residential homes 3 Thanks to the lack of cables and switches our radio system works without interefering with low frequency electro magnetic emissions 4 This radio system is used in schools hospitals and even in houses built according to Feng Shui principles 3 2 0 Safety information OP Il N CO lt Nw Xo When planning where to locate your dev
3. User manual for HEATSTRIP radio receiver Remote control systems HEATSTRIP This installation and user manual encompasses information about the following products MHS FBM MHS FBHS MHS FBWS MHS ESM Designpreis Deutschland reddot design award 2011 winner 2010 Exclusively engineered and made in Germany 1 Table of contents 1 0 Use page 2 2 0 Safety Information page 2 3 0 Functionality description page 4 4 0 Assembly page 5 5 0 Programming page 7 6 0 Operation page 9 7 0 Connecting element MHS ESM page 10 8 0 Technical Information back page Delivery Radio receiver module 1 piece Power connector already installed on the machine 2 pieces Assembly and user manual 1 piece and optionally Hand held remote control 1 piece or Wall mounted remote control 1 piece 1 0 Use 2 0 Safety information Thank you for choosing HEATSTRIP the black light infrared electric heater This user manual will guide you through the connection and programming of the radio receiver MHS FBM These instructions are an addition and valid only in combina tion with the general HEATSTRIP manual chapter 4 7 Our remote controls are powered by the EnOcean technology which enables them to run battery free When pressing the button of the remote control the system harnesses the physical pressure of your thumb onto the remote control and converts it into an electro magnetic signal that is picked up by our MHS FB
4. all the connecting element after point 4 0 in this user manual It is not possible to further program or set this element 8 0 Technical data User Manual 2 1 Valid from 11 11 2011 RoHS compliant Green Smart Wireless enocean WEEE Reg Nr DE 45650441 MHS GmbH Munich Home Systems Kramergasse 32 Operating voltage Wattages Heat output Warming up time Measurements Power cable Cable length Compatability Transmission range Transmitter Performance Transmission duration Security Humidity Temperature range Storage temperature Shutdown D 82054 Sauerlach b M nchen Tel 49 0 8104 64709 0 Fax 49 0 8104 64709 9 info heatstrip de www heatstrip de 230 V 50 Hz maximum 3200 W 3 setting approx 10 to 15 minutes depending on the weather temperature outside wind circa 170 x 90 x 65mm EUR or IK plugs 1 5m 3 x 1 5mm sq up to max 28 transmitters approx up to 100m free 868 3 MHz frequency maximum 10 mW approx 25ms 32 Bit encryption with up to 3 telegrams maximum 85 from 0 C to 40 C from 30 C to 65 C as a built in factory setting the receiver automatically shuts down after 12 hours of continuous use
5. er press the ON button again Remote to Power 0 OFF press the OFF button remote to Power 2 2 green LEDs turn on press in OFF button again remote to Power 1 1 green LED turns on press in OFF button again remote to Power 0 OFF All 3 green LEDs turn on Standby operation heating off blue LED lit The Party Mode has a preset heating duration of 4 hours running on maximum heat supply regardless of the Time Code set see section Setting of maximum heating duration above Press and hold the ON button for more than 6 seconds The heater is set on maximum heat and will switch off automatically after 4 hours The green and blue LEDs are lit Press and hold the OFF button for more than 6 seconds The heater turns off regardless of the current heating setting The blue LED displays the standby mode to check the functionality of the receiver module without using the transmitter Press the lateral button on the receiver for more than 10 seconds gt the heater turns on 2 LEDs are lit 80 power Press the programing buttons again for for more than 10 seconds the heater turns off If not the device is automatically turned off after 2 hours The blue standby LED turns on 7 0 Connecting element The connecting element serves as a stylish cable connection for your Heatstrip hiding the power cable at the backside of the device instead of it being visible at the front side Inst
6. ice please check accessibility to the different components as you may have to access them in the future Electronic components may also fail and have to be replaced Only to be installed by a professional Please check the cable cross section between the heater and the power supply is sufficient in terms of size and power The surrounding temperature should not exceed 40 degrees Celsius Exclusively for 230V 50 Hz AC Keep the devise away from physical chocs and do not use force Protect from wetness and moisture Do not install in the proximity of open fire Do not install where surrounding temperatures are constantly below O degrees Celsius 3 0 Functions description 4 The radio transmitter operates with a closed signal in the 866Mhz region You can program a maximum of 28 radio transmitters i e remote controls per single MHS FBM receiver The 32BIT encryption provides protection from any signal confusion from other devices such as mobile phones or garage remote controls The blue LED signals that the remote control is ready to use The number of green LEDs lit indicates the chosen heat intensity You can select your requested heat settings by pressing the buttons on the remote control remote control MHS FBHS remote control MHS FBWS 4 0 Assembly Caution antenna is not removable x a P Lu ET as E e s tee g Programming button Legend 1x MHS Heatstr
7. ip 5 1x MHS FBM 6 2x Sockets 1 2x Bolts 2 1x Power connector 3 2x Screws 4 Remove the lateral screw cap in order to reach the programming button Once the programming is complete please put the screw cap back in place Caution When synching the Heatstrip Heater with the MHS FBM receiver please make sure to place the remote control in a perimeter less than 5 meters away from the Heatstrip Receiver When the programming mode is on make sure to maintain the power supply to the receiver as a potential power cut can damage the device Fix the sockets 1 on the bolts 2 Screw the bolts into the Heatstrip heater 5 Plug the connector 3 to the heater and push the two elements together until you feel a click Fix the MHS FBM receiver or the connecting element MHS ESM 6 until it clicks with the connector Place the screws 4 in and turn tight to secure the fixing O O e Oo Up 7 Light Scheme LED Display green blue O 5 5 12 h 7 blinks off on Remote control programming Press briefly the lateral button on the MHS FBM receiver less than 1 sec Three green LEDs one blue LED flash two times per second On the remote control press and release the button you wish to control the device with Then the LEDs blink for 2 seconds while the radio button is being synchronized with the MHS FBM receiver To terminate the programming mode wait for

Remote control systems

Contents

Download Pdf Manuals

Related Search

Related Contents