Product User Manual - Photonic Energetics Model PE-1
Contents
1. PHOTONIC ENERGETICS Product User Manual Photonic Energetics 700 Valerie Drive Raleigh NC 27606 Internet www photonicenergetics com Email Info photonicenergetics com Phone 919 233 8272 PHOTONIC ENERGETICS Product Description The Photonic Energetics Dynamic Light Therapy Model One provides a feature rich high power combination visible far red and invisible infrared light therapy product in an ergonomic compact and lightweight yet very durable enclosure The Model One provides selectable bio resonate Nogier frequencies and selectable output intensity levels which allow the unit to be customized to individual requirements The Model One provides the many clinically established therapeutic benefits of concentrated light delivery systems in addition to providing beneficial Nogier bio resonant frequency groups Refer to enclosed CD for documents that describe key benefits and study references General Specifications and Features 140 LED high density high power array with approximately 1100 milliwatts radiated output power over a surface area of 8 5 sq in 55 sq cm 112 near infrared LEDs invisible e 56 940 nm 36 880 nm and 20 875 nm 28 red far red LEDs visible e 20 655 nm and 8 680 nm Selectable pulse and direct continuous output mode 10 bio resonant Nogier derived pulse frequencies Auto sequence random frequency select mode High precision quartz oscillator and digital circuitry Precis2. condition requiring treatment Use of several complementary groups are advantageous and are described the referenced document Thus selecting several different frequencies at different intervals during a session may produce the most beneficial results Also switching to the Direct mode periodically may also be helpful particularly for problematic areas In general the higher frequencies tend to be more calming sedating and the lower frequencies tend to be more energizing activating The general actions of the Nogier frequency groups is further elaborated in the document enclosed with the unit titled Definition of frequencies by Drs Paul and Rapha l NOGIER Remember to translate the Nogier frequency group to the actual control setting on the light unit frequency select switch by referencing the Nogier Therapeutic Applications chart The setting J on the frequency control selects the Auto sequence random frequency select option In this setting the pulsed frequency shifts every 7 seconds in random order covering all Nogier frequency groups Pulsed frequencies selected are 4 6 Hz 9 2 Hz 73 2 Hz 146 5 Hz 293 Hz 586 Hz 1171 9 Hz 4687 6 Hz This mode provides a general toning effect and may be very beneficial in working with problematic areas where chronic or stuck conditions exist PHOTONIC ENERGETICS Product Handling Maintenance Storage and Transportation General Handling The PE 1 unit is made from very durable m
3. handling or excessive exposure to water dust or other harsh or corrosive environments Exclusions to the warranty also include evidence of failure resulting from lightning damage fire or other natural catastrophes Further warranty exclusions include user modification attempted repair and or disassembly of the unit Also failures or damages resulting from apparent uses of the product for those that are specified in the original instructions provided with unit are not covered by the product warranty Refund Policy e The Photonic Energetics Dynamic Light Therapy product refund policy provides for a new purchase return grace period of 30 days in the event the customer is not satisfied with the purchase subject to a 10 restocking charge The customer is required to make prior arrangements for the refund and then return the undamaged unit for evaluation prior to the issuance of the refund The customer is responsible for the insured shipment charges incurred in the return shipment of the product Damaged scarred or incomplete product returns are subject to a charge assessment corresponding to the incidental damages found The customer is responsible for all damages or missing materials that are identified Photonic Energetics Frequency Control Nogier Therapeutic Action For tissue of mesodermal origin such as bone joints ligaments viscera and tendons Field experience has shown group C to be especially good for tendon and ligament
4. injuries when used with groups B and G It also helps in relaxing large muscle groups For chronic conditions not responsive to groups A or C Field experience shows group D to be a good supplement to group A when healing processes appear to reach plateau For pain control Primarily when C nerve fibres are transmitting to dorsal root ganglia and when involvement of neurotransmitters is of physiological importance Field experience shows group E to help suppress pain and sedate acupuncture and trigger points and other nerve tissue Group E also aids in diminishing excess calcification associated with chips spurs and arthritic conditions For use when cellular activity is hypoactive such as chronic recurring problems non union fractures and chronic splints and for stimulation of osteoid bone growth It is also helpful in 73 Hz activating humoral and endocrine functions hormone problems Fieldwork has shown group F helpful in stimulating tonifying acupuncture and trigger points and increase circulation in areas being treated such as wounds when past the acute stage For areas of yellow scar tissue that are generally formed internally on tendons ligaments and sub acute lingering but not chronic conditions Field use has shown group G to be helpful in reducing inflammation associated with injuries and infections For circulatory and lymphatic stimulation and treatment of tissue of endodermal origin such as Gl track liver and pancr
5. unit is properly receiving power The unit will beep 3 times when initially turned on Press the Start switch and the LED array will automatically illuminate and operate for 15 minutes and then automatically turn off The unit will beep 3 times now signaling the LED array has powered down Press the red Start button on the front control panel to restore power to the LED array for another timed 15 minute session The main Power switch may be turned off at any time to end a session before the automatic timeout period ends and power the unit down PHOTONIC ELNERGETICS Directions for General Use Recommendations for getting started Click the Mode switch right side panel to the Pulse position Choose the F setting on the Frequency control as a good beginning point This is considered to be a universal frequency in acupuncture Choose the 5 setting on the Intensity control This selects the 50 power level As you become familiar and comfortable with the unit the power may be increased by selecting a higher number on the control The intensity level may be adjusted to match specific individual needs The level can be reduced if lower stimulation levels seem effective Begin by using the light unit in a slow scanning motion around the toe nails feet ankles finger nails hands wrists and base of the spine These locations are associated with key acupuncture points and are beneficial places to begin treatment Normally kee
6. TE ER HA PAKOKO D OKIN IAN DEEM EKEKOL DH Ken an whl nt xes MR I OTe OH Of Pv oar es 0X We 5 me NK TERAK K OFS OW RO LET REN TF PHOTONIC ENERGETICS Optional Battery Pack Use Care and Charging General Information The PE1 BAT optional battery is a 12 Volt 5 0 Amp Hour re chargeable pack of Ni MH construction The battery pack power cord is fitted with the appropriate power connector and polarity to mate with the PE 1 light therapy unit An AC powered smart charger is supplied to re charge the battery pack The battery can be re charged up to 1000 times using the smart charger When fully charged the pack should power the PE 1 for up to 30 fifteen minute sessions when operated in the Pulsed mode and up to 15 fifteen minute sessions when operated in the Direct Continuous mode Handling and Storage The battery pack should always be kept in the padded carrying case to protect it from the environment and from rough handling that could cause permanent damage Do not use the PE 1 in wet or extremely dusty environments Be careful to not drop the unit or step on the power cord and connector or roll over it with a chair etc Charging Instructions NOTE The Smart Charger is fitted with the correct power connector and polarity to mate with the PE1 BAT battery pack The smart charger should be used in an indoors environment only Connect the battery pack to the Smart Charger connector and plug in the Smart Char
7. aterials and should require very little general maintenance if used in normal dry environments Do not use in wet or extremely dusty environments Rough handling should be avoided Be careful to not drop the unit or step on the power cord and connector or roll over it with a chair etc Maintenance Instructions e Periodic light cleaning using grain alcohol a glass cleaner or a slightly damp cloth with a drop of mild dish detergent will remove any soiling and help to preserve the appearance of the unit e Avoid heavy scrubbing with very harsh chemicals or abrasive materials Product Storage and Transportation e Store the unit in the provided carrying case to protect it during times that it is not being used To transport the PE 1 use either the standard padded carrying case or optional field fanny pack Either padded carrying case can be used to hold the PE 1 and the optional battery pack for field use Prepare the PE 1 for storage by extending the power cord to its full length and allow any twists to gently unravel Then roll the power cord in the form of a coil about 6 inches to 7 inches in diameter Start the coil loops from the black power cord strain relief located at the left side of the unit and fold it toward the right side of the unit and underneath the back of the unit Storing the unit with the cord coiled as described will extend the life of the cord The picture below illustrates this method Seyi ei en OCW OW ET peer Meer ta
8. e digital intensity control 10 increments Automatic shutdown 15 minute timer with audible tone alert and manual restart High capacity universal protected 120 240 Volt AC 4 Amp power supply 12 volt car adapter and high capacity rechargable 12V battery packs are optional Measurements 6 length 4 width 1 25 depth PHOTONIC ENERGETICS Basic Operation Instructions Control Functions Power On Off Left Panel switches main power on off Mode Right Panel selects either Pulse or Direct continuous mode Start starts 15 minute timed session unit automatically turns off and beeps at end of session pressing start button initiates a new session Frequency selects specific Nogier frequency see Nogier chart for details Intensity selects power output intensity in progressive 10 increments Initial Use e Plug the provided AC power cord into the AC power adapter This adapter supplies the required to 12 volt DC to operate the unit Ensure the cord is snuggly seated in the adapter and plug the 3 prong wall plug on the other end into a 120 VAC wall power outlet The green light on the adapter should now be illuminated Plug the light unit DC power cable into the mating DC connector on the power adapter The unit is now ready for powering up Click the Power control left panel to the On position The small red LED above the power cable on the front control panel should now be illuminated indicating the
9. eas In field applications group B has been used in conjunction with groups C and G for tendon ligament joint and other injuries where reaching secondary levels of tissue is needed For tissue of mesodermal origin such as bone joints ligaments viscera and tendons 1172 Hz Field experience has shown group C to be especially good for tendon and ligament injuries when used with groups B and G It also helps in relaxing large muscle groups For pain control Primarily when C nerve fibres are transmitting to dorsal root ganglia and when involvement of neurotransmitters is of physiological importance Field experience 4688 Hz shows group E to help suppress pain and sedate acupuncture and trigger points and other nerve tissue Group E also aids in diminishing excess calcification associated with chips spurs and arthritic conditions Automatic sequencing mode Pulsed frequency shifts every 7 seconds in random order covering all Nogier frequency groups Pulsed frequencies selected are 4 6 Hz 9 2 Hz 73 2 Hz 146 5 Hz 293 Hz 566 Hz 1171 9 Hz 4687 6 Hz For tissue of ectodermal origin such as body openings skin and nerve Field applications include wounds and following surgery Group A tends to tone up tissue while minimizing 293 Hz the chance of hemorrhaging in fresh wounds or recent surgical sites It is also beneficial for the treatment of acupuncture and trigger points and ulcerated mucous membranes This is called a universal fre
10. ger AC cord into an AC power source The Smart Charger indicator LED will then flash red twice and green twice and then will detect the battery voltage automatically The LED indicator light on the smart charger will shine steady red if the battery is below the full charge level The battery will automatically begin charging The charger indicator LED will shine steady red while the battery is undergoing charging The time required for charging the battery is approximately 6 hours or overnight to reach a full charge When the battery is fully charged the charging current will automatically reduce to around a 50 milliamp mA trickle and the indicator LED on the charger will turn from red to green indicating the charge cycle is complete The battery pack can then be disconnected from the charger The fully charged voltage of the battery pack will be approximately 14 Volts at the completion of the charge cycle The PE1 BAT battery pack can then be connected to the PE 1 unit power cord connector and the unit will then be ready for extended field use PHOTONIC ENERGETICS Product Warranty and Refund Policy Product Warranty e The Photonic Energetics Dynamic Light Therapy product warranty covers failures incurred during normal usage and provides for full coverage of parts and labor for a period of one year and for parts only for a period of two years Exclusions to the warranty include evidence of damages resulting from rough or abusive
11. ontrol is functioning in the Direct mode and at the 10 setting the unit is producing it s maximum output level The unit will warm considerably in the direct mode at full power So even though it is safe it is not recommended to operate it at direct maximum power continuously in multiple back to back sessions PHOTONIC ENERGETICS Directions for General Use Directions for using the Nogier Frequencies Click the Mode switch right side panel to the Pulse position The LED array will then be pulsed with the frequency selected by the rotary Frequency selection switch on the front control panel Refer to the chart titled Nogier Therapeutic Applications Detail Descriptions chart that is provided with the unit to identify the selectable frequency options The Frequency Control is is labeled A J and the the settings correspond to the Control Setting column in the above mentioned document NOTE The frequency control labeling is not the same as the labeling of the Nogier frequency groups The chart provides a listing of the frequency control settings and identifies the specific frequency of the setting and links them to specific Nogier frequency groups and the associated description of their physiological and neurological therapeutic actions The Nogier Therapeutic Applications chart will serve as a guide to select the Nogier group and corresponding frequency setting that is most appropriate for the specific
12. ping the light unit from 1 to 6 inches from the body will be effective Initially limit the duration of the first few sessions from 5 to 7 minutes and then progressively extend to key focus areas as needed Normally use of the light unit several sessions a day is beneficial and well accommodated to treat focus areas where some form of injury or distress may exist Full strength of the unit may be realized by placing it directly in contact with the focus areas for several minutes It is important to note that a small percentage of individuals may be considerably more sensitive to light stimulation than normally robust individuals If this is known or detected then the power level should be reduced to a very low setting and the treatment time should be limited to very brief intervals 30 seconds to 1 or 2 minutes Also the light unit should also be held at a distance of 1 to 3 feet away from the sensitive individuals body Generally a sensitive person will acclimate favorably to light therapy and after repeated sessions will be able to tolerate progressively higher power settings and longer exposure times The unit may then be used closer to the body after the individual acclimates Directions for using the Direct Mode e Click the Mode switch right side panel to the Direct position The LED array will then operate in a continuous steady on state The frequency control is bypassed and thus non functional in this mode The intensity c
13. quency in acupuncture The Frequency Control is is labeled A J and the the settings correspond to the Control Setting column in the above mentioned document NOTE The frequency control labeling is not the same as the labeling of the Nogier frequency groups Be sure to cross reference the frequency control setting to the corresponding Nogier group when using this chart The chart provides a listing of the frequency control settings and identifies the specific frequency of the setting and links them to specific Nogier frequency groups and the associated description of their physiological and neurological therapeutic actions The Nogier Therapeutic Applications chart will serve as a guide to select the Nogier group and corresponding frequency setting that is most appropriate for the specific condition requiring treatment PHOTONIC ENERGETICS Photonic Energetics Treatment Frequency Application Table Derived from Nogier Principles of Bio resonate Body Tissue Types According to Embryologic Origin Photonic Energetics Frequency Control Setting u Nogier Group Frequency Hz u a u Source for this information is from the book Healing Energies of Heat and Light A Quantum Leap in Heathcare by Charles T McGee MD Medipress 2000 Bio resonate Tissues and Organs Primary tissue type Ectoderm Central Nervous System brain and spinal cord Peripheral nerves Ear Mammary glands Pituita
14. ry gland anterior and posterior Enamel of teeth Body of the adrenal gland Primary tissue type Endoderm Lining of the GI tract Lining of the Lung Thyroid gland Thymus Liver Pancreas Lining of the bladder Urethra Auditory tube Primary tissue type Mesoderm Cartilage Bone Muscle Heart Blood and lymph vessels Kidney Ovaries Testes Spleen Cortex of the adrenal 10 PHOTONIC ELNERGETICS Photonic Energetics Dynamic Infrared Light Therapy Contact Information Email info photonicenergetics com Phone 919 233 8272 Web www photonicenergetics com
Download Pdf Manuals
Related Search