TRAV`LER® WINEGARD®
Contents
1. HD capable DSR207 SD only DVR530 HD capable DVR Each receiver will require at least one coax cable Refer to receiver manual for wiring details For information regarding Satellite coverage in North America call Shaw Direct at 1 888 554 7827 Before you begin please make sure you have received all necessary parts to properly install and oper ate your TRAV LER antenna Installation and Operation Manuals Mount Base with 30 Cable Power Control Cable TRAV LER Interface Box Reflector LNBF amp Feed Arm Packaged separately as the SKA 733 TRAV LER Power supply with 24 AC power cord Gray Coax Cable 30 Black Coax Cable 30 Mounting Hardware bag Cable Entry Hardware bag Selecting a Location for the TRAV LER Antenna Before removing the TRAV LER antenna from its box check with your RV Dealer or manufacturer Your RV may be pre wired or have a reinforced area for this system DO NOT install in a location where a gap of 3 16 or more exists as it may damage the roof See diagram at top of page 3 Plate If not using this plate make sure that the roller does not come in contact with any rib supports When installing the TRAV LER on a rubber roof Winegard recommends using the SKA 004 Roller or bubbles in the roof when in operation Failure to do so may result in damage to the roof INSTALLATION 2 ts Plan your entire installation before you start Determine the location of as 3 16 al2. recommended that you don t pre drill the holes at this time Use a solid bead of sealant to connect these marks in the shape of the base Replace the TRAV LER antenna base and screw it to the roof Check with your vehicle manufacturer for any special screw requirements before using the supplied screws INSTALLATION 4 DO NOT SEAL FIGURE 4 LIP OF TRANSITION PLATE WARNING DO NOT cut any wires when you drill the hole for your cables SEAL Run a solid bead of sealant around the transition plate making sure to cover each screw head Be careful not to get any sealant above the lip of the transition plate See diagram of transition plate GPS Installation The GPS antenna is connected to the TRAV LER by a 6 cable running to Port E on the TRAV LER Mount To install it find an open area to either side of the TRAV LER Mount at least 18 inches from the mount and place a small dot of sealant Place the GPS antenna on the sealant and press it into place Secure any excess cable WARNING DO NOT CUT the GPS cable Cable Entry Plate Installation Decide the best location for the cables to enter the vehicle 4 Winegard recommends in stalling the Accessory Detect Cable this can provide an A coax directly to each receiver location emergency stow function A control cable to the TRAV LER Interface box You will need to run Drill a 1 2 hole in the roof and push the reguired wires through Installations for multiple recei
3. a Hex Connector Find a location to plug in the TRAV LER Power supply and plug it in Reflector Installation Once the wires are run and the sealant has started to cure Check to be sure that there is nothing above the TRAV LER that might prevent it from raising You will need at least 40 of clearance above the TRAV LER Mount to ensure that you have room to install the reflector Raise Antenna There are two ways to raise the antenna Either Automatic or Manual explained below Automatic Steps 1 7 explain how to use the TRAV LER Interface box to raise the mount to install the reflector 1 Press POWER and hold for 2 seconds to turn ON the TRAV LER Interface Box Wait until the Interface Box finishes connecting to antenna The TRAV LER may enter the Search Routine after 10 seconds this is normal See NOTE Below 2 Press ENTER and hold for 2 seconds or until the unit displays Enter User Menu Press SELECT to move the asterisk to Yes Press ENTER 3 Press SELECT to move the asterisk to INSTALLATION 4 Press ENTER You will be asked to provide a code to enter the Installation Menu 5 Press ENTER 4 times to enter code 0000 6 Press SELECT to move the asterisk to RAISE ANTENNA Press ENTER Press SELECT to move the asterisk to Yes 7 Press ENTER the TRAV LER mount will raise up about half way NOTE If the TRAV LER enters the Search Routine you can still enter th
4. STATUTORY INCLUDING WARRANTIES OF FIT NESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY ARE LIMITED TO THE TWO YEAR PERIOD OF THIS WARRANTY In states that do not allow limitations on implied warranties or the exclusion of limitation of incidental or conseguential damages the above limitations or exclusions do not apply Some states do not allow limitations on how long an implied warranty lasts or the exclusion of limitation of incidental or conseguential damages so the above limitations or exclusions may not apply to you This warranty gives Customer specific legal rights Customer may also have other rights that may vary from state to state SATELLITE RECEIVER WARRANTY See manufacturer s limited warranty policy WS MOBWARREV2 Rev 1 10 DO NOT paint this antenna AN Painting the TRAV LER antenna will void your warranty INSTALLATION 10 INSTALLATION 11 SHAW DIRECT Winegard Company gt 3000 Kirkwood St Burlington IA 52601 2000 319 754 0600 FAX 319 754 0787 e www winegard com Printed in U S A Winegard Company 2012 1 12 2452252
5. WINEGARD TRAV LER Automatic Multi Satellite TV Antenna SHAW DIRECT Model SK 7003 INSTALLATION MANUAL Winegard Company 3000 Kirkwood St Burlington IA 52601 2000 319 754 0600 FAX 319 754 0787 www winegard com Printed in U S A Winegard Company 2012 1 12 2452252 Congratulations You have selected the Winegard TRAV LER Automatic Multi Satellite TV Antenna The TRAV LER antenna will deliver the ability to view both SHAW DIRECT satellites at the same time with unmatched signal strength the lowest travel height on the market maximum HD capabilities and easy to use func tionality just like you get at home This manual provides important information on the installation and operation of your TRAV LER Interface Box Please take time to read the manual in it s entirety before installing or operating your antenna Icons appearing in the manual are used for important information and helpful tips Alert indicates important information regarding product use product specifications or procedures ve Important tip offers helpful suggestions or Q refers you to a related topic in the manual Recommended Receivers The Winegard TRAV LER Automatic Multi Satellite TV Antenna will work with any SHAW DIRECT receiver currently in production Consult your receiver manual or www winegard com if you have any questions about whether your receiver is compatible However we recommend SHAW DIRECT DSR505
6. amaged deteriorates malfunctions or fails from im proper installation misuse abuse neglect accident tampering modification of the product as originally manufactured by Winegard in any manner whatsoever removing or defacing any serial number usage not in accordance with prod uct instructions or acts of nature such as damage caused by wind lightning ice or corrosive environments such as salt spray and acid rain This Limited Warranty also does not apply if the product becomes unable to perform its intended function in any way as a result of the television signal provider making any changes in technology or service RETURN AUTHORIZATION POLICY A Return Material Authorization RMA is reguired prior to returning any product to Winegard Company or Winegard Warranty Services under this warranty policy Please call our Technical Services Department at 800 788 4417 or send an e mail to warranty winegard com to obtain the RMA number Please furnish the date of purchase when reguest ing an RMAnumber Enclose the product in a prepaid package and write the RMA number in large clear letters on the outside of the package To avoid confusion or misunderstanding a shipment s without an RMA number s or an unauthorized return s will be refused and returned to Customer freight collect WINEGARD COMPANY DOES NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES EXPRESS OR IMPLIED MADE BY ANY OTHER PERSON ALL OTHER WARRANTIES WHETHER EXPRESS IMPLIED OR
7. ate EL In Progress 10 After a few moments the IDU LCD will display On EL Hard Stop Yes No Visually examine the antenna to verify that the antenna is against the Hard Stop The antenna will be pointing as far up as it can go this is the Hard Stop 11 Press SELECT once to move asterisk to Yes if antenna is on the Hard Stop 12 Press ENTER and the LCD will display Calibrate EL Success 13 You may now stow the antenna INSTALLATION 7 SHAW DIRECT WARNING Pay attention to these Pinch Points as the antenna raises NOTE Pinch Points are called out both for your safety and to protect the cables Cables will be damaged if installed incorrectly Refer to the SKA 733 installation manual Pages 3 4 for proper cable attachment Pinch Point FIGURE 7 Using the 4 bolts and nuts provided attach the reflector to the mounting bracket Press POWER to lower the antenna to the travel position Note The nuts securing the dish should be tightened to 6 8 Ib ft Hooking up the Shaw Direct receiver Connect your Shaw Direct receiver to the TV using the appropriate audio and video cables Refer to your televi sion user manual for the best audio video connections If you have not chosen a programming package for your Shaw Direct system or added this receiver to your exist ing Shaw Direct account please call 1 888 554 7827 prior to using your Shaw Direct receiver for the first time Ensure that y
8. e Menu Mode See Steps A amp B p 7 If the TRAV LER Mount raises past 1 2 way before RAISE DISH is selected See Step 6 the TRAV LER will hit its Upper Hard Stop and Motor Stall appears This is Normal The Motor Stall means the TRAV LER is all the way up amp mount can raise no more There are two easy ways to clear the Motor Stall INSTALLATION 6 A Press ENTER the TRAV LER will return to the Installation Menu OR B Press POWER the TRAV LER will stow and turn OFF Restart at Step 1 Refer to the SKA 733 Manual for instructions on how to install the Reflector and Bracket Manual 1 Press POWER and hold for 2 seconds to turn ON the TRAV LER Interface Box Wait until the Interface Box finishes connecting to antenna The TRAV LER may enter the Search Routine after 10 seconds this is normal See NOTE Below 2 Press ENTER and hold for 2 seconds or until the unit displays Enter User Menu Press SELECT to move the asterisk to Yes Press ENTER 3 Press SELECT to move the asterisk to INSTALLATION 4 Press ENTER You will be asked to provide a code to enter the Installation Menu 5 Press ENTER 4 times to enter code 0000 6 Press SELECT to move to Calibrate EL 7 Press ENTER 8 Press SELECT to move to YES 9 Press ENTER to start the elevation calibration procedure The LCD should now display Cali br
9. is critical If you have the basic technique right you can modify it to your own personal taste Whether you use a knife stripping tool or diagonal cutter the important thing is to make a good clean cut A hex crimping tool is required for hex connectors for maximum RF transmis sion Cut the cable flush Strip the outer jacket off 1 2 then trim the dielectric by cutting partially thru DO NOT NICK THE CENTER CONDUCTOR Twist and pull off leaving a 1 2 minu mum of exposed center conductor As mentioned before the choice of tools is yours Be sure you do a precise job Failure to do so can cost you time and money in trying to locate a system problem E ZZ y a IN HOT WEATHER Trim off center conductor leaving 3 16 beyond the connector The center conductor expands at higher temperatures If a little extra is not provided it may contract enough in the winter to cre ate an open connection and result in loss of picture Look into end of connector to make sure no braid or aluminum foil touches or has the possibility of touching the center conductor Shorting can result if either comes in contact with center conductor Close crimping tool making correct crimp Slide connector onto coax Trim off excess braid EMERGENCY MANUAL STOW 1 1 Unplug TRAV LER Interface 2 Remove the black plastic bolt from the back of the mount FIGURE 8 3 Insert a 5 16th socket extension into the auxiliary drive a
10. l of your eguipment and make sure cable and wires are long enough to ST TTT reach their destination points You must find a location on the roof that provides adequate space to allow the TRAV LER antenna to operate The TRAV LER antenna has a Front and Back and must be mounted correctly to avoid dam age to the TRAV LER antenna or the coach The antenna must be mounted 5 degrees of level or the system may reguire more time to locate the satellite s The Transition plate for the TRAV LER unit is marked FRONT and BACK See Figure 1 FIGURE 1 7 N TRANSITION PLATE O za Mount _ Parallel to oO Center Line Winegard is NOT liable for dam of Coach age expenses or injury caused by improper installation lt A Once you have checked for this 1 Choose a location on the roof of the RV that will allow the dish to raise and rotate without interfer ence from other roof mounted equipment The TRAV LER antenna may only be mounted parallel to the centerline of the coach N 29 6 66 ZLI y o Kg TIR n TW N Io 6 W SREY ji cd BEAC E web Ten x 5 2 M 7 3 FF 45 81 FIGURE 2 Mount Parallel to 2330 Center Line of Coach R4 AO LNOYS 2 The minimum roof space reguired for the TRAV LER antenna is 46 L x 38 W a The operational space reg
11. our Shaw Direct receiver is connected to power Locate the coaxial feed coming from TRAV LER system Connect the satellite feed to the coaxial input labeled with the symbol of a satellite dish Power on the Shaw Direct receiver and television If your TRAV LER system is properly tuned and receiving signal the satellite dish icon on the front of the Shaw Direct receiver will be highlighted in green If the TRAV LER system is stowed or not tuned to the Shaw Direct satellites the satellite icon on the front of the Shaw Direct receiver will appear in red Turn on the TRAV LER unit or troubleshoot as needed to reachieve posi tive signal If your Shaw Direct system is disconnected from power for an extended period of time or you has been recently moved from another location you may need to have your Shaw Direct system reauthorized This can be deter mined when you receive a green positive signal but cannot receive video on a subscribed channel To initiate a signal refresh call 1 888 554 7827 then select Self Serve Technical Support followed by Signal Refresh from the telephone menu options For changes to Shaw Direct programming or to purchase new Shaw Direct eguipment visit shawdirect ca or call 1 888 554 7827 NOTE The TRAV LER antenna will find the satellites without the receiver installed Rev 4 09 INSTALLATION 8 Appendix Making the Right Connection with Hex Connectors Making a coaxial cable connection
12. s shown in Figure 8 Turn auxiliary drive clock wise to lower the unit NOTE DO NOT USE A DRILL To Lower Unit turn Clockwise INSTALLATION 9 Remove additional 1 4 of the outer jacket Pull the braid away from th dielectric and fold over the jacket If there s any residue on the center conductor scrape off with non metallic object IN COLD WEATHER OR INDOORS Trim off center conductor leaving it extended 1 16 of an inch beyond the connector Use diagonal pliers for cutting center conductor EMERGENCY MANUAL STOW IS MEANT AS A LAST RESORT AND NOT FOR COMMON USAGE AUXILIARY DRIVE SHAW DIRECT WINEGARD MOBILE PRODUCTS LIMITED WARRANTY 2 YEARS PARTS 1 YEAR LABOR Winegard Company warrants this product against defects in materials or workmanship for a period of two 2 years from the date of original purchase During year one 1 of such warranty Winegard Company will also pay author ized labor costs to an authorized Winegard dealer to repair or replace defective products No warranty claim will be honored unless at the time the claim is made Customer presents proof of purchase to an authorized Winegard dealer to locate the nearest authorized Winegard dealer contact Winegard Company 3000 Kirkwood Street Burlington lowa 52601 Telephone 800 288 8094 or visit www winegard com Customer must provide proof of purchase with a dated sales receipt for the Winegard product to verify the product i
13. s under warranty If the date of purchase cannot be veri fied the warranty period shall be considered to begin thirty 30 days after the date of manufacture If a defect in material or workmanship is discovered Customer may take the product to an authorized Winegard dealer for service Customer must provide proof of purchase to verify the product is under warranty If the product is brought to an authorized Winegard dealer for service prior to expiration of year one 1 of the warranty period and a defect in material or workmanship is verified by Winegard Technical Services Winegard Company will cover the Win egard dealer s labor charges for warranty service The Winegard dealer must contact Winegard Technical Services in advance for pre approval of the service Approval of the service is at the sole discretion of Winegard Company Alternatively Customer may ship the product prepaid to Winegard Technical Services located at 3111 Kirkwood Street Burlington lowa 52601 Telephone 800 788 4417 Customer must return the product along with a brief descrip tion of the problem and provide Winegard Technical Services with Customer s name address and phone number Customer must also provide proof of purchase to verify the product is under warranty If the product is returned before the expiration of the warranty period Winegard Company will at its option either repair or replace the product This Limited Warranty does not apply if the product has been d
14. uires that no obstructions taller than 8 inches be mounted within a 70 diameter circle from the center of the unit INSTALLATION 3 SHAW DIRECT 3 The unit must be within 5 of level for best operation 4 Make sure that the location offers enough support to attach the TRAV LER antenna securely 5 Find a well ventilated location with a 110 V outlet for the TRAV LER Interface inside the vehicle Make sure to clean the installation area before you begin You will want to decide where the wires will enter the vehicle One coax cable per receiver and a control cable will need to be run into the vehicle Warning Do not run the wires through the striped area shown Consult your receiver manual for specifics in the diagram FIGURE 3 TRANSITION PLATE 24 inches 32 86 1 23 50 seuoul 81 1 Ri NOTE Anything in the striped area will interfere with the operation of the TRAV LER antenna and may cause damage to the object or the TRAV LER antenna TRAV LER Mount Installation Verify that the FRONT of the transition plate is facing the front of the vehicle then place the TRAV LER antenna mount on the roof where you plan to install it See Figure 3 Mark where the screw holes will go by placing marks through the holes in the mount base on the roof of the RV It is impor tant that you be able to see these marks Move the TRAV LER mount out of the installation area It is
15. vers may reguire a larger hole or multiple holes as each receiver reguires a dedicated coax cable Each receiver will reguire at least one coax cable See receiver manual for wiring details Place the cable entry plate supplied in hardware bag over the hole and cables Screw the plate in place and seal the plate and screw holes with approved sealant not included Depending on the length of the cable on the roof you may need to use cable clamps between the unit and your cable entry plate Clamping every 12 16 should eliminate any unnecessary cable movement FIGURE 5 OVERALL INSTALLATION DRAWING AV For best results use TV 1 for the receiver that will POWER be most active SUPPLY i 40 INOYI The SK 7003 will support up to four receivers Rev 4 15 08 INSTALLATION SHAW DIRECT Cable installation Connect the control cable and power cable to the back of the TRAV LER Interface box as shown below Note For cable runs longer than 25 an extension may be purchased Do not exceed 50 of cable FIGU RE 5A Control Cable 7 2 O Bn IU Attach the TRAV LER control cable to the TRAV LER Interface Box as shown in Figure 5A Attach the output cable from the Power supply to the TRAV LER Interface Box See above Finally connect a coax cable from the TRAV LER mount to each of the receivers being used with the TRAV LER Automatic Satellite Dish See Appendix for information on properly installing
Download Pdf Manuals
Related Search