Full User Manual
Contents
1. DT70 unit to be configured and a small blunt instrument such as a toothpick or straightened paperclip Make sure the unit is unpowered and not connected to anything 1 3 Using the blunt instrument hold down the RESET button then power on the unit by plugging in the power adapter When you see the POWER LED blink RED release the RESET button then the POWER LED should turn ORANGE Only when the POWER LED is ORANGE can you access the unit s configuration web page also known as Setup Mode 1 4 Next connect the unit to your computer using any standard Ethernet cable Once the cable is connected the STATUS LED turns green 1 5 Open a browser and enter the following Setup IP address depending if the unit you are configuring is a transmitter or a receiver 1 5 1 Transmitter PCA 192 168 168 211 1 5 2 Receiver TVA 192 168 168 22 E Microsoft Internet Explorer CD Back EQ x 2 Oh H Search Address 4 192 168 168 21 Opening page http 192 168 168 21 EH TT ip Internet E 1 6 You will see the settings web page where you can enter the Operational IP address This address is in effect only when the device is in normal AV operation when POWER LED is not ORANGE and is different from the Setup IP address above which is permanent and cannot be changed The Setup IP address in effect only when the POWER LED is ORANGE Even if you have set an Operational IP address previously ente2. IR repeater using the front panel IR receiver e EXTERNAL IR enables the IR repeater using the external IR jack e RETURN goes to the previous menu 2 Run time OSD When the DT11 RX is streaming video from a source transmitter the OSD options are different than in 1 above Again pressing the SOURCE button brings up the OSD DVD 1 00 00 20 connected APPLE 3 00 00 26 REFRESH VGA SYNC PCA SETTING TVA OFF EXIT e Inthe Run Time OSD the list of available transmitters is listed first In the example here two transmitters are shown DVD 1 and APPLE 3 The numbers in the parentheses are its MAC addresses The connected status indicates that this DT11 RX unit is currently showing the AV stream from the transmitter DVD 1 To select another transmitter s content to display simply press the SOURCE button again until it is highlighted wait three seconds and its stream will be shown instead e VGA SYNC appears only if input at transmitter is VGA re synchronizes VGA signal e REFRESH will search the network again for any enabled DT11 TX PCA units e PCA SETTING brings up the options for the currently selected transmitter Select this option to go to the next menu below e TVA OFF disables the DT11 RX from displaying any video or audio e EXIT turns off the OSD MULTI ONE TVA BANDWIDTH SETTING INFORMATION EXIT e MULTI ONE TVA brings up the MULTI ONE menu below e BANDWIDTH SETTING brings up the BANDW
3. OSD DT11 RX i opp As for the remote repeater you can either use the built in or external IR receiver on the DT11 RX side On the transmitting side plug in the included IR transmitter into the IR OUT port and aim it directly at the AV device s IR receiver window Ensure that the proper IR setting is selected in the OSD DT11 RX DT11 TX og NY Cony 0 3008 j hatot Simply plug in the PS 2 devices into their respective ports on the transmitter then power up the receiver On the transmitter side use the included USB cable to connect the transmitter s USB port to an unused USB port on the computer Your computer may prompt you that it has detected new hardware so just follow the prompts to complete the installation process DT11 TX DVI VGA A One important note when using multiple receivers per transmitter Only the MASTER DT11 RX will have the functional keyboard mouse and IR port with respect to each transmitter To set which DT11 RX is the MASTER unit turn off all other DT11 RX units power up the desired unit first and allow it to establish a connected to the transmitter See the INFORMATION OSD screen above on how to display the DT11 RX s MASTER SLAVE status When the desired DT11 RX unit is already set as MASTER all other DT11 RX units can be powered up PC A 100Mb s switch MASTER unit DT11 RX DT11 RX DT11 RX connected 1st st DN Ns SLAVE units connected after MAST
4. ure NED InternetVue HD Multimedia Extender DT11 KIT DT11 RX DT11 TX DT 70 TX User Manual v1 0 mbox technology Introduction Thank you for purchasing the DT11 Multimedia Extender With the DT11 you can send high definition audio and video from one or more sources to one or more displays over an Ethernet network Furthermore the DT11 can also relay IR remote control signals as well as PS 2 keyboard and mouse inputs from a remote display location to a source PC or consumer electronics device Hardware Remote On Off switch VGA pass through output Remote on off TRANSMITTER DVI VGA select switch DVI I video input DC input jack RJ45 network jack USB to PC Ext IR port DECSV 2A DVI VGA In IR Out DT11 TX One port Transmitter PCA PC Adapter STATUS LED POWER LED Status Power Audio ports Reset button DC input jack USB to PC Port Connector DC input Jack USB to PC Remote On Off External IR port VGA pass through DVI VGA select DVI I input Status LED Power LED Audio ports Reset button Ethernet port s ACCESSORIES IR Transmitter STATUS LED Remote On Off switch Ext IRjack DVI I video input Reset button 7x 10 100 Ethernet ports DAVAL ET AN Audio ports VGA pass through DT70 TX Seven port Transmitter PCA PC Adapter Purpose 5V DC power input Keyboard and mouse input to PC Enables Disables peripherals connected to receiver unit Conne
5. 80 x 720 30 fps o 1920 x 1080 25 fps o 1280x1024 30 fps e Receiver outputs both DVI D and VGA signals regardless of input signal on transmitter e Built in browser based configuration for easy user setting of Operational IP address and device naming e Permanent hard coded Setup IP address are as follows o Transmitter PCA 192 168 168 21 o Receiver TVA 192 168 168 22 e STATUS LED colors o Off No network connection o Green Network connected o Blinking green Network activity o Orange Red High network bandwidth usage e POWER LED colors o Off Unpowered o Green Powered on and connection established with corresponding TX or RX unit o Red Powered on but no connection to corresponding TX or RX unit o Blinking Red Reset button held down ready to enter Setup mode o Orange Unit is in Setup Mode Configuration and Setup 1 You will need to set fixed IP addresses for each of your DT11 devices This is necessary for proper operation and so that the DT11 units will not interfere with any other devices on your network However you can skip setting the IP addresses on the units and go to Step 2 only if e The TX and RX units are connected only by an Ethernet cable with no router or switch in between one to one operation DT11 TX DT11 RX e There is only one TX unit and one or more RX units are connected through a switch but no PCs or routers are connected to that switch one to many operation DT11 TX DT11
6. ER Remote On Off Switch Each DT11 TX DT70 TX transmitter unit has a front panel REMOTE ON OFF switch This switch disables all input devices keyboard mouse and IR remote control on a Master DT11 RX from controlling the computer or AV device connected to the transmitter Remote On Off switch For technical support please visit www addlogix com wbs 02009 atBox Technology Inc No part of this User Guide can be copied reproduced transmitted or otherwise used without the prior written consent of atBox Technology Inc
7. IDTH menu below e INFORMATION displays the current operating modes of both the receiver and currently selected transmitter e EXIT turns off the OSD gt ONE TVA ONLY gt MULTI TVA gt EXIT e ONE TVA ONLY sets the currently selected transmitter to Unicast mode wherein only this receiver can display that transmitter s content e MULTI TVA sets the currently selected transmitter to Multicast mode wherein more than one receiver can display that transmitter s content e EXIT turns off the OSD e LOW MID and HIGH are various bandwidth settings which can be selected to save network bandwidth These settings are effective only when the content being displayed is 1280x720 or higher e EXIT turns off the OSD PROTOCOL VERSION 0 91 SUPPORT MULTI TVA BANDIWDTH High DVI IN 1024 768 PROTOCOL VERSION 0 91 DVI OUT 1024 768 MIC IN INTERNAL IR e Here is the INFORMATION screen It displays all the relevant information about the DT11 RX TVA and the currently selected transmitter PCA Keyboard Mouse Mic and IR Remote Repeater Use Input devices can be connected to the DT11 RX in order to control the transmitting device connected to a DT11 TX or DT70 TX These devices can be a PS 2 keyboard PS 2 mouse microphone or standard IR remote control The microphone is set up in a similar way simply plug in the mic or other low level audio source into the MIC IN jack on the DT11 RX Make sure that the MIC IN is enabled in the
8. RX Saas DT11 RX e There is only one TX unit and one or more RX units are connected through a switch PCs and or routers are connected to that switch but reside on a subnet other than 192 168 168 x one to many operation DT11 TX DT11 RX DT11 RX PCs on 192 168 1 x subnet 1 1 First you will need to connect a computer using an Ethernet cable to each DT11 TX and RX unit in order to access its configuration web page In your computer s network adapter settings give it a fixed IP address of 192 168 168 100 subnet mask 255 255 255 0 In Windows XP this can be done using the following procedure 1 1 1 Go to CONTROL PANEL gt NETWORK CONNECTIONS gt right click LOCAL AREA CONNECTIONS then click on STATUS Click on the PROPERTIES button scroll down and double click on Internet Protocol TCP IP In the next window enter the IP address and subnet as shown below Internet Protocol TCP IP Properties You can get IP settings assigned automatically if your network supports this Seamer Otherwise you need to ask your network administrator for the a Obtain an IP address automatically f Use the following IP address IP address 192 168 168 100 Subnet mask Default gateway Obtain DHS server address automatically Use the following DNS server addresses Prefered DNS server Atemate DNS server 1 1 2 Click OK then OK then CLOSE 1 2 Now prepare the DT11 or
9. URCE button on the front panel The OSD menu provides the user with various settings and the ability to select which source video stream ME to display x e Press the SOURCE button to cycle through the various options e To select an item leave the desired item highlighted for three seconds 1 DT11 RX TVA Setup via OSD To set the options of the DT11 RX TVA unit make sure that the DT11 RX is not connected to the network Power it up with a display and the following message will appear SEARCHING PCA NOT FOUND Wait a few seconds until the message disappears the press the SOURCE button to bring up the OSD gt REFRESH gt TVA SETTING gt TVA OFF e REFRESH will search the network again for any enabled DT11 TX PCA units e TVA SETTING brings up the options for the DT11 RX Select this option to go to the next menu below e TVA OFF disables the DT11 RX from displaying any video or audio gt AUDIO INPUT gt IR INPUT gt RETURN e AUDIO INPUT brings up the MIC input settings menu see below e IR INPUT brings up the IR remote input menu settings menu see below e RETURN goes to the previous menu MIC IN DISABLE MIC IN ENABLE RETURN e MICIN DISABLE turns off the MIC input to save bandwidth e MICIN ENABLE turns on the MIC input e RETURN goes to the previous menu IR DISABLE INTERNAL IR EXTERNAL IR RETURN e IR DISABLE turns off the IR repeater to save bandwidth e INTERNAL IR enables the
10. cts to IR emitter Allows you to connect a local VGA monitor Works only if source is also VGA Selects between the VGA or the DVI D pins on the DVI I input connector Video signal input utilizes either DVI D or the VGA signals through the select switch Displays network connection status Displays power and operation mode status Audio signal input from source to RX speaker and output audio from RX to PC mic Resets unit and provides operation mode selection 10 100 Ethernet connection s to RX unit s through LANs or direct connections External IR VGA M to DVI F DVI M to VGA F Cables Receiver adapter adapter IR receiver window External IR jack POWER LED SOURCE button STATUS LED Source Status O Power RECEIVER DC input jack PS 2 keyboard and mouse ports RJ45 network jack DVI I video output Audio ports Reset button input Port Connector DC input Jack PS 2 connectors IR receiver window External IR jack Source button DVI I output Status LED Power LED Audio ports Reset button Ethernet port me nn 20 VGA Out Audio Out Mic in oO olor o FF zz mine DT11 RX One port Receiver TVA TV Adapter Purpose 5V DC power input PS 2 keyboard and mouse input for remote PC control Receives IR remote control signals Connects to external IR receiver Multifunction button that allows selection of various sources and other functions Video signal output transmits both DVI D and VGA signals simultaneously Dis
11. luded external receiver and plug that into the Ext IR port in front If you are using the device on a network you can plug an Ethernet cable into the receiver now and that cable into the network DT11 RX DT11 RX The included all in one cable can be used to extend the devices if the DT11 RX is in an inaccessible location Lastly power up the unit by plugging in its power adapter The POWER LED should be RED and the STATUS LED should be GREEN DT11 RX 2 2 Transmitter The included cable is used to conveniently connect a PC to the transmitter Connect your computer or source device to the transmitter s DVI I port You may need a DVI VGA or DVI HDMI adapter If the signal coming from the source is DVI or HDMI be sure to set the DVI VGA switch to DVI If the signal is VGA set the switch to VGA Next plug one end of the audio cable into the Audio In jack on the transmitter and the other end into your computer or source device s Line Out or Speaker Out jack The audio cable also has a pass through female connector for a local speaker connection If you are using a keyboard and or mouse plug in the USB cable into the USB port on the transmitter and the other end into a free USB port on your computer If you are using the IR repeater function plug the included IR emitter into the IR Out jack and point the IR emitter to the device being controlled If you are using the device on a network you can plug an Ethernet cable into the receive
12. plays network connection status Displays power and operation mode status Audio signal input from mic to TX and output audio from TX to speakers Resets unit and provides operation mode selection 10 100 Ethernet connection from TX unit s through LAN or direct connection Features and Specifications e Very low latency Audio SD and HD Video transmission over Ethernet networks e Send video from multiple sources to multiple destinations over the same Ethernet network e Adjustable bandwidth e Receivers can select which source transmitter to display using pushbutton and OSD e Standard 38 kHz IR remote control repeater from receiver back to transmitter e Accepts VGA and DVI D input signals including HDMI NOTE HDCP and digital audio are not supported and requires DVI HDMI adapter not included e Accepts stereo audio input e Works with any computer operating system e Remote On Off switch at transmitter disables peripherals connected to receiver e Relays mic input from receiver back to transmitter e Transmitter accepts video resolutions from 640 x 480 to 1920 x 1080 from 60Hz to 70Hz refresh e Built in scaler scales output video to display s capability regardless of input video resolution e Receiver output resolutions and frame rates are as follows o 640x480 70 fps o 1360x768 30 fps o 720x480 60 fps o 1400 x 1050 30 fps o 720x576 50 fps o 1440x900 30 fps o 800x600 70 fps o 1600x1200 30 fps o 1024 x 768 60 fps o 1680x1050 30 fps o 12
13. r now and that cable into the network or you can plug the other end directly into the transmitter DT11 TX Local speaker anmannan Audio output Line In or Mic input DVI or VGA output Setup with a PC DT11 TX Local speaker HDMI DVI I Adapter not included Setup with a Consumer Electronics device such as a DVD player with HDMI output At this point you can also plug in a local VGA monitor to the transmitter But note that the local VGA monitor will only work if the input signal is also VGA DT11 TX Lastly power up the unit by plugging in it s power adapter The POWER LED should be RED and the STATUS LED should be GREEN DT11 TX 2 3 DT70 Transmitter The DT70 TX is identical as the DT11 TX except that it has a built in 7 port Ethernet switch with IGMP snooping designed specifically for use with multiple DT11 units You can plug seven other DT11 devices directly into the DT70 TX without the need for additional network hardware DT70 TX DT11 RX Direct to receivers DT11 RX AND OR To other switches i DT11 RX 2 4 Repeat steps 2 1 to 2 3 above for all DT11 DT70 devices that would be in use 2 5 IMPORTANT WHEN USING MULTIPLE TRANSMITTERS ON THE SAME NETWORK Transmitters can consume up to 99 of available bandwidth on a 100Mb s Ethernet link when running at 1080p Therefore the ideal method of connecting multiple transmitters to multiple receiver
14. ring this Setup mode will revert all settings back to the factory defaults PC2TV TVA2 Settings Product Type PCITV TVA2 Firmware Version 0091 0x93 18 Network Protocol MAC Layer IP Layer Status JDone Now you can enter an IP address for this unit and also a friendly device name Some rules of thumb e Because the DT11 DT70 units will not be interacting with any other devices on your network the IP address should be on a subnet which is currently not used by any device on your network For example if your router and DHCP server use the 192 168 1 x subnet you set all your DT11 DT70 devices to another subnet such as its current factory subnet 192 168 168 x However be sure that every DT11 DT70 unit has a unique address e For the Device Name use a descriptive name which can easily be identified by the user See example below PC2TV TVA2 Settings Permitted IP Address Ranges e 192 168 0 0 to 192 168 254 254 e 172 16 0 0 to 172 31 254 254 e 10 0 0 0 to 100 254 254 254 Gateway IP Device Name Lobby TV 4 Network Protocol MAC Layer IP Layer Save Exit Status Done e When done click on SAVE then EXIT The unit will restart 1 7 Disconnect the Ethernet cable from your computer and the unit The DT11 DT70 unit is now configured with the IP address 192 168 168 200 and Device Name Lobby TV 1 8 Repeat steps 1 2 to 1 7 for all DT11 DT70 units in yo
15. s is to have all transmitters connected to a single switch using a direct connection without any additional 100Mb s switches in between This ensures that each transmitter has a full LOOMb s link to the switch DT11 RX 100mbys 100mbys 100M F 100Mb s TTN 00Mb s DT11 RX 100Mb s switch with Hr DT11 TX OOMb s eee IGMP snooping 100Mb s An alternative is to have a Gigabit link in between switches to accommodate the additional bandwidth used by the multiple transmitters DT11 7X 100Mb s switch w gigabit port i 100Mb s and IGMP snooping DT11 TX oe DT11 TX 00Mb s TESE vs Feie 1000Mb s 100Mb s DT11 RX 100Mb s Senn S808 naan ve eS pegy pm Ze DT11 RX 100Mb s switch w gigabit port 100Mb s and IGMP snooping DT11 RX Most importantly switches used with multiple DT11 DT70 transmitters must have IGMP snooping functionality This is critical in preventing multiple multicast streams from flooding the entire network causing all other network devices such as computers to have slow or no access to the network The IGMP snooping feature in switches intelligently identifies and routes the AV packets from the transmitters only to the appropriate DT11 RX destinations not to computers that don t need it This frees up bandwidth thereby allowing other network traffic to pass OSD Functions The DT11 RX includes an On Screen Display OSD menu which is enabled by SOURCE button pressing the SO
16. ur setup making sure each unit has a different IP address but MUST HAVE the same first three octets ie 192 168 168 x Here is an example Unit Type Device Name IP Address DT11 RX Lobby TV 192 168 168 200 DT11 RX Upstairs TV 192 168 168 201 DT11 TX DVD Player 1 192 168 168 202 DT11 TX DVR 192 168 168 203 1 9 Go back to the TCP IP properties window as shown in step 1 1 1 above and change it back to Obtain an IP address automatically Click OK then OK then CLOSE General Atemate Configuration gl ee ee ee Otherwise you need to ask your network administrator for the appropriate P settings Internet Protocol TCP IP Properties a ES Use the following IP address IP address e eed Subnet mask aos Default gateway MT Obtain DNS server address automatically Use the following DNS server addresses Preferred DNS server Alternate DNS server Now that all your DT11 DT70 devices are configured properly you can begin connecting all the hardware and peripherals together 2 1 Receiver Connect your display to the receiver s DVI I port You may need a DVI VGA adapter or DVI HDMI adapter Next plug in the speakers or audio amplifier to the Audio Out jack of the receiver If you are using a keyboard and or mouse you can plug those into the receiver as well If you are using the IR repeater function you can either just use the built in IR window on the receiver or use the inc
Download Pdf Manuals
Related Search