Home

Displays

1. Figure 1 6 Tilting the FI10 Box Down e After removing the screws tilt the box together with the shield plate in the case of the FI15 backwards away from the front plate The box is held by a hinge below and a cord above SIMATIC PC BI10 F110 F115 Technical Description 1 12 C79000 G7076 C773 03 System Unit Figure 1 7 Removal for FI15 SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 1 13 System Unit f j Figure 1 8 Tilting the FI15 Box Down e When the front plate is tilted down the following components can be seen on the front plate LC display Inverter module LC display plug adapter Keyboard controller Touch screen controller optional Touch pad controller only with FI15 Touch pad adapter only with FI15 SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 System Unit Inverter LC display LCD plug adapter Sp
2. Figure 1 33 FI15 with Reset Button SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 1 37 System Unit On the FI10 and BI10 the reset button is located on the box in the area of the slot plates This reset button can be activated by hand without the need for any additional tool The following figure shows the position of the reset button on the FI10 and BI10 devices a ay Reset Button A I Figure 1 34 FI10 BI10 with Reset Button SIMATIC PC BI10 F110 F115 Technical Description 1 38 C79000 G7076 C773 03 System Unit 1 5 Error Diagnostics Table 1 1 Errors in PC Operation Error Power ON LED does not light up Cause Power supply is not properly connected Remedy Check power supply con nections power cable and power plug The Invalid configuration information Press the F1 key for continue F2 to run Setup utility appears on the display screen Incorrect configuration data Buffer battery is low or damaged Press F2 key check the configuration data in SETUP enter any default values and check error messages in the first SETUP menu The No boot device available appears on the display screen There is no boot diskette in the drive Wrong hard disk drive set in SETUP Use
3. Figure 1 11 Removing the Display in the FI10 SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 System Unit Figure 1 12 Removing the Display in the FI15 VGA TFT or SVGA TFT SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 System Unit 1 4 4 Removing and Installing the Keyboard Controller e Open the PC as described in Section 1 4 1 e Remove the two connecting cables of the membrane keyboard Caution Release the socket connector locking before removing the connecting cables to avoid any damage to the foil coating e Before disconnecting all cables please write down their previous connections e Release the four mounting screws then take out the keyboard controller module Please proceed in reverse order to reassemble the unit Figure 1 13 Removing the Keyboard Controller in the FI10 SIMATIC PC BI10 F110 F1I15 Technical Description 1 18 C79000 G7076 C773 03 System Unit Figure 1 14 Removing the Keyboard Controller in the FI15 SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 1 19 System Unit 1 4 5 Repla
4. 03 System Unit Chapter Section Description Page Oveniew 11 TechnicalSpecifications 2 1 2 Dimensions of Expansion Modules 1 3 Power Requirements of the Components Maximum Values 1 4 Removing and Installing Components 1 4 1 Opening and Closing the System Unit 1 10 1 4 2 Opening and Closing the Front Panel 1 11 1 4 3 Removing and Installing the Flat Screen Inverter 1 4 4 Removing and Installing the Keyboard Controller 1 4 5 Replacing Backlight Tubes for Displays 1 20 1 4 6 Removing and Installing the Disk Drive for BI10 FI10 1 27 1 4 7 Removing and Installing the Disk Drive for FI15 1 28 1 4 8 Removing and Installing the Hard Disk Drive 1 4 9 Removing and Installing Expansion Modules 1 4 10 Removing and Installing the Bus Board 1 32 1 4 11 Removing and Installing a Fan 1 33 1 4 12 Removing and Installing the Power Supply Unit 1 4 13 Removing and Installing the CPU Board 1 4 14 Connecting the MPI DP Interface 1 36 1 4 15 Reset Button 1 37 1 5 Error Diagnostics 1 39 SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 1 1 System Unit 1 1 Technical Specifications Dimensions W x Hx D in mm 330 x 290 x 120 front SIMATIC PC FI10 305 x 265 cut out Dimensions W x Hx Din mm 295 x 235 x 100 SIMATIC PC BI10 Dimensions W x Hx Din mm 450 x 335 x 120 front SIMATIC PC FI15 305 x 420 cut out Weight SIMATIC PC
5. 8 kV air discharge to IEC 1000 4 2 1995 Immunity to high frequency noise 10 V m 80 1000 MHz 80 AM to ENV 50140 1993 10 V m 900 MHz 50 ED to ENV 50204 1995 Ambient conditions SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 System Unit Temperature tested to DIN EN 60068 2 2 1994 DIN IEC 68 2 1 DIN IEC 68 2 14 operation 5 C to 45 C storage transport 20 C to 60 C gradient max 10 C h no condensation Relative humidity tested to DIN IEC 68 2 3 DIN IEC 68 2 30 DIN IEC 68 2 56 operation 5 to 85 at 25 C no condensation storage transport 5 to 95 at 25 C no condensation Mechanicalspecifications Vibration tested to DIN IEC 68 2 6 operation 10 to 58 Hz 0 075 mm 58 to 500 Hz 5 m s transport 5 to 9 Hz 3 5 mm 9 to 500 Hz 5 m s Shock tested to DIN IEC 68 2 29 operation 50 m s2 30 ms 100 shocks transport 250 m s 6 ms 1000 shocks Mother board Processor Pentium Internal processor cache 8 Kbytes code 8 Kbytes data Main memory 128 Mbytes max Second Level Cache none Free expansion slots 1 ISA 290 mm long 1 shared ISA PCI 290 mm long Max permissible current consumption per ISA slot Max permissible current consumption per PCI slot SV 2A 12V 0 3A 12V 0 05A SV 2A 12V 0 5A 12V 0 1A A total of 8 A must not be exceeded at 5V Drives Floppy
6. BI10 F110 F115 Technical Description 1 28 C79000 G7076 C773 03 System Unit 1 4 8 Removing and Installing the Hard Disk Drive e Open the system unit as described in Section 1 4 1 e Remove the hard disk drive as described in Section 1 4 6 e The hard disk drive is screwed to a support This support is fixed to the floor of the system housing with four screws Remove these screws and lift the support out of the unit e Before disconnecting the cables please write down their previous connections e Release the four screws which mount the floppy disk drive to the vibration reducing part of the support Take the hard disk drive out of the drive support Figure 1 26 Removing the Support for the Hard Disk Drive SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 1 29 System Unit Figure 1 27 Removing the Hard Disk Drive from the Support Proceed in reverse order to install a new drive SIMATIC PC BI10 FI10 FI15 Technical Description 1 30 C79000 G7076 C773 03 System Unit 1 4 9 Removing and Installing an Expansion Module e Open the system unit as described in Section 1 4 1 e Release the two screws of the retainer approx 1 turn Adjusting Insert the sliding element and push it down until it covers the module Then Retainers guide the module into the notch e Tighten the two screws Caution Pressure
7. Remove the PC from its support cabinet only necessary if mounting screws are inaccessible in the installed state e Remove the four screws see Figure 1 4 on the housing cover Then remove the housing cover When the housing cover is removed the following functional units can be seen in the housing Mother board Passive bus board Fan only in the FI15 Hard disk drive Floppy disk drive only with FI10 and BI10 Power supply SafeCard optional Figure 1 4 Opening the System Unit SIMATIC PC BI10 F110 F115 Technical Description 1 10 C79000 G7076 C773 03 System Unit 1 4 2 Opening and Closing the Front Plate In the FI10 and FI15 the system housing computer box is attached to the front plate from behind The fixing mechanism allows the computer box to be moved out and tilted down by 90 in the installed state Please proceed as follows e In the case of the FI10 remove all the screws that attach the computer box to the front plate e In the case of the FI15 the computer box is also screwed to a shield plate Only remove the screws that attach the shield plate to the front plate The computer box of the FI15 can remain screwed to the shield plate Figure 1 5 Removing the Front Plate of the FI10 SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 1 11 System Unit
8. 4 30 PL A 0 1 All dimensions in mm el 810 bag 28 0 max All dimensions in inches 3 19 0 91 Figure 1 1 XT Module 11 42 ka 290 e airy e g 2e A31 A1 es 2 54 17 PL 2 54 30 PL 0 1 0 1 23 0 max All dimensions in mm ka 0 91 All dimensions _ in inches ee Figure 1 2 AT Module SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 1 5 System Unit 11 42 290 gt x oO ye 25 ni All dimensions in mm All dimensions in inches Figure 1 3 Long PCI Module 5 V 1 6 SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 System Unit 1 3 Power Requirements of the Components Maximum Values Basic System Maximum Current Delivery Components 5V 3 3V 12V 12V 5Vp Mother board 23A 15A o1A 002A 024A Monitoring board 0 35 A 0 03A SafeCard 2 Direct key module 2 O4A Fan 0 3 A 3 5 floppy disk drive 0 4 A Hard disk 0 4 A 0 3 A VGA TFT display 1 0 45 A VGA TFT inverter 1 05A SVGA TFT display 1 0 23 A SVGA TFT inverter 1 0 35 A STN display 1 0 23 A STN inverter 1 0 35 A Keyboard controller O 12A Touch Screen Controller 0 25 A Either SVGA TFT VGA TFT or STN is installed 2 Optional The power supply permits a maximum current d
9. 7 5 Kbps The data transfer rate that can be achieved via MPI DP interface in the PROFIBUS DP network ranges from 9 6 Kbps up to 1 5 Mbps Note For further information on configuring a PROFIBUS DP network please refer to the S7 300 Hardware and Installation manual Order no 6ES7030 0BA00 8AA0 Isolated within SELV circuit SIMATIC PC BI10 F110 F1I15 Technical Description C79000 G7076 C773 03 System Unit 1 4 15 Reset Button The FI10 FI15 and BI10 devices are equipped with a reset button When you press the button the device is cleared and reset The PC is restarted On the FI15 the reset button is integrated in the front panel under the cover next to the floppy disk drive The reset button can only be activated using a pointed object for example the tip of a ballpoint pen or the end of an opened paper clip The following diagram of the FI15 shows the position of the reset button 127 5 121 335 125 E SIEMENS SIMATIC PC F15 450 rca Oo5o000 o0025000000
10. C mains voltages at 50 60 Hz It is a varying voltage power supply unit so voltage changeover is not necessary SIMATIC PC BI10 F110 F115 Technical Description 1 34 C79000 G7076 C773 03 System Unit 1 4 13 Removing and Installing the CPU Board e Open the system unit as described in Sectio 1 4 1 Jand remove all expansion modules see Section 1 4 9 e Remove any disk drive see Section 1 4 6 or 1 4 7 e Remove the hard disk support and the hard disk drive together see Section e Remove the fan see Section 1 4 11 e Remove the power supply unit see Section 1 4 12 e The module is still attached to the rear plate by three screws and to the port side of the computer housing with ten hexagonal bolts Remove these e Then lift the module out of the computer housing Lift the side containing the PCMCIA slot out of the computer housing first 8 hexagonal jolts 2 hexagonal olts Figure 1 32 Removing and Installing the CPU Module Proceed in reverse order to reinstall the board or to install a new one Note Replacement CPU modules are supplied without memory submodules processor cooling unit or voltage transformer SIMATIC PC BI10 FI10 FI15 Technical Description C79000 G7076 C773 03 1 35 System Unit 1 4 14 Connecting the MPI DP Interface Connecting a PROFIBUS DP Network via the MPI DP Interface ZN PROFIBUS DP Network 1 36 You can connect your PC to PROFIBUS DP netw
11. FI10 approx 7 5 kg Weight SIMATIC PC BI10 approx 5 kg Weight SIMATIC PC FI15 approx 8 kg Line voltage 120 to 240 VAC tolerance range 85 265 VAC Line voltage frequency 50 60 Hz 47 to 63 Hz Brief voltage interruption acc to NAMUR max 20 ms at full load max power consumption lt 120 W max current delivery internal SV 12V 3 3V 12V 5V floating 1 5A 8A 2 5Amax 10s 2 2A 0 2 A 0 24A Degree of protection SIMATIC PC FI10 Front IP65 otherwise IP20 Degree of protection SIMATIC PC BI10 Front IP20 Degree of protection SIMATIC PC FI15 Front IP65 when flap of diskette drive closed Safety Safety class Protection class I acc to VDE 0106 T1 1982 IEC 536 Safety requirements EN60950 acc to IEC 950 09 91 acc to DIN VDE 0805 A4 1997 Electromagnetic compatibility EMC Emittedinterference EN 55022 class B Noise immunity line fedinterference 2kV to IEC 1000 4 4 1995 burst 1kV to IEC 1000 4 5 1995 surge symm 2kV to IEC 1000 4 5 1995 surge unsymm Noise immunity on signal lines 1kV to IEC 1000 4 4 1995 burst length lt 3m 2kV to IEC 1000 4 4 1995 burst length gt 3m 1 kV to IEC 1000 4 4 1995 surge symm length gt 3m 2 kV to IEC 1000 4 4 1995 surge asymm length gt 3m Immunity to discharge of static electricity 6 kV contact discharge to IEC 1000 4 2 1995
12. SIEMENS System Unit 1 Mother Board SIMATIC Keyboard Controller Direct Key Module PC BI10 F110 FI15 Bus Board Technical Description Displays Monitoring Module Touch Screen O O N OO OF FP W ND Hard Disk Drive mart Floppy Disk Drive oh ool Power Supply Appendices Guidelines for Handling Electro A statically Sensitive Devices ESD Index Safety Guidelines ZN ZN ZN Qualified Personnel Correct Usage ZN Trademarks This manual contains notices which you should observe to ensure your own personal safety as well as to protect the product and connected equipment These notices are highlighted in the manual by a warning triangle and are marked as follows according to the level of danger Danger indicates that death severe personal injury or substantial property damage will result if proper precautions are not taken Warning indicates that death severe personal injury or substantial property damage can result if proper precautions are not taken Caution indicates that minor personal injury or property damage can result if proper precautions are not taken Note draws your attention to particularly important information on the product handling the pro duct or to a particular part of the documentation Only qualified personnel should be allowed to install and work on this equipment Qualified persons a
13. ace for touch screen controller opt aM Keyboard controller Figure 1 9 Rear View of FI10 Front Plate LC display Inverter LCD plug adapter Touch screen controller opt Keyboard controller Touch pad adapter Touch pad Figure 1 10 Rear View of FI15 Front Plate SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 1 15 System Unit 1 4 3 Removing and Installing the Flat Screen Inverter e Open the industrial PC IPC as described in Sectio e Before disconnecting all cables write down their previous connections e The flat screen and its inverter module are screwed to the front unit e Release the four screws by which the display unit is mounted to the device and take the unit out e The inverter module of the TFT SVGA display is fastened to the front plate with a special support plate the inverter module of the TFT VGA display is fastened to the front plate with two screws and the inverter module of the STN display is fastened to the front plate with four plastic rivets Release the screws or rivets The rivets are released by pushing their thorns out of the body of the rivet from behind Caution Do not forget to mount the insulating sheet between the inverter module and sheet metal while installing
14. be seated correctly and must be covered with reflector foil The cables connected to the tube must be laid in the appropriate channels Reassemble the rear panel of the display see Figure 1 23 and replace the 4 screws Turn the 2 metal lugs back to the original skewed position Check that the tube functions correctly metal lugs Figure 1 21 Metal Lugs on the Edge of the Display SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 1 25 System Unit 4 screws 2 left 2 right back plate Figure 1 22 Applying the Screwdriver 4 reflector film Figure 1 23 Disassembling the Rear Panel of the Display SIMATIC PC BI10 F110 F115 Technical Description 1 26 C79000 G7076 C773 03 System Unit 1 4 6 Removing and Installing the Floppy Disk Drive in the BI10 FI10 e Open the system unit as described in Section e Release the two screws in the system unit with which the floppy disk drive is attached that are located above the fan as well as the screws in the system housing next to the floppy disk slot e Release the locking mechanism for the controller cable at the disk drive and pull the cable out of the connector e Follow the above instructions in reverse order to install the new drive The new drive must be of the same type as the drive you removed A S7 Figure 1 24 Installing the Floppy Disk Dri
15. cing Backlight Tubes for Displays Replacement in the STN Display 1 20 The backlight tube of the LC display is subjected to wear Depending on the operating temperature the brightness of the tube and hence the brightness of the display will become less We recommend you replace the tube when your display has dimmed to 50 of its original brightness The so called half life period of your display is indicated in operating hours in the description of your LC display The backlight tube can be ordered as a spare part The tube should be replaced in a dustproof room and according to ESD guidelines The replacement should be carried out by our authorized service personnel or in an authorized service shop The backlight tube for the STN display is replaced as follows e Remove the display from the front plate as described in Section e Place the display face down on a flat dust free surface e Align the 17 metal lugs 3 at the left 7 on top 7 on bottom see Figure 1 15 e Remove the 6 screws as shown in Figure 1 15 2 left 4 right e Disassemble the rear panel of the display as shown in Figure 1 16 e Lift the reflector foil at the top edge of the display and remove the backlight tube carefully e Insert the new backlight tube and cover it with the reflector foil e The sealing rings O rings on the tube must be seated correctly and must be covered with reflector foil e The cables connected to the tube must be laid in the ap
16. d licenses apply only to expansion functions approved by SIEMENS No liability can be assumed for functional constraints caused by the use of devices and components of other manufacturers The following sign warns that electrostatically sensitive modules are present Please read the ESD guidelines A la SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 System Unit Before Opening the Unit Tools Before opening the unit you should carefully read the following rules Before you disconnect the power supply cable discharge any electrostatic charge on your body for example by touching screws on the rear panel of the PC Discharge any electrostatic charge from tools that you are using Wear a grounding wrist strap if you are handling components Leave components and modules in their packing until you are ready to install them Disconnect the PC from its power supply before plugging in or removing any modules or components Touch components and modules only on their edges Above all do not touch the connecting pins or printed conductors Do not operate the PC with the cover open Use a suitable crosstip or TORX screwdriver to remove or install components SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 1 9 System Unit 1 4 1 Opening and Closing the System Unit Computer Box e Remove the diskette from the floppy disk drive e Disconnect the power supply e
17. deviations cannot be pre cluded entirely we cannot guarantee full agreement However the data in this manual are reviewed regularly and any necessary cor rections included in subsequent editions Suggestions for improve ment are welcomed Siemens AG 1998 Subject to change without prior notice SiemensAktiengesellschaft C79000 G7076 C773 Contents 1 System UN t iocs eee eee ee ee ees a a a eee eee ee 1 1 Technical Specifications 6 00 cette 1 2 Dimensions of Expansion Modules 0 0 0 ce eee e eee ees 1 3 Power Requirements of the Components Maximum Values 1 4 Removing and Installing Components 00e eee eee eee ee 1 4 1 Opening and Closing the System Unit Computer Box 1 4 2 Opening and Closing the Front Plate 00 0 cc eee eee eee 1 4 3 Removing and Installing the Flat Screen Inverter 1 4 4 Removing and Installing the Keyboard Controller 1 4 5 Replacing Backlight Tubes for Displays 0000 eee eeeeeee 1 4 6 Removing and Installing the Floppy Disk Drive in the BI10 Fl10 1 4 7 Removing and Installing the Floppy Disk Drive inthe Fl15 1 4 8 Removing and Installing the Hard Disk Drive 00005 1 4 9 Removing and Installing an Expansion Module 0 1 4 10 Removing and Installing the Bus Board 00 000 c cece eee 1 4 11 Removing and I
18. disk drive 3 5 1 44 Mbytes Hard disk drive 3 5 EIDE see Logbook LC Display SIMATIC PC F115 FI15 VGA TFT FI15 SVGA TFT Display size display type 10 4 inches VGA TFT 10 4 inches SVGA TFT Resolution Colors 640 x 480 VGA 256K 800 x 600 SVGA 256K Contrast 100 1 60 1 Brightness 250cd m 150 cd m Response time 30 50 ms 30 50 ms Faulty spots permitted high low level lt 12 25 spots green high level lt 5 spots high low level lt 12 25 spots green high level lt 5 spots LC Display SIMATIC PC F110 FI10 VGA DSTN FI10 VGA TFT Display size display type 10 4 inches VGA 10 4 inches VGA TFT Resolution Colors 640 x 480 VGA 256K 640 x 480 VGA 256K Contrast 30 1 100 1 Brightness 80cd m2 250 cd m Response time 270 ms 30 50 ms Faulty spots permitted high low level lt 12 25 spots green high level lt 5 spots Graphics Graphics chip SVGA LCD Controller Cirrus GD7543 on PCI Windows accelerator Graphics memory 1 Mbyte DRAM Resolutions frequencies colors With LCD up to 800x600 256 colors With CRT up to 1024x768 256 colors at 72 Hz SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 System Unit Interfaces COM1 Serial port 1 V 24 25 pin sub D socket connector NS 16550 compatible or TTY active passive COM2 Serial port 2 V 24 9 pin sub D connect
19. e cover cannot be opened Filter cap not properly fixed Push filter cap in proper position SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 1 39 SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03
20. elivery of 70 W The following current values must not be exceeded Power Supply 5V 3 3V 12V 12V 5Vp Maximumcurrentdelivery 80A 22A 15A Joza 024A max 2 5 A for 10s i7 SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 System Unit 1 4 Removing and Installing Components Prerequisites ZN ZN Limitation of Liability 1 8 The system unit is designed to enable any necessary maintenance work to be carried out quickly and at low cost Warning Please read the warnings on the first pages of the user s guide before you open the housing of the system unit e Do not open the housing unless you need to install or remove components or to replace the battery e Write down your configuration parameters before starting the procedure Caution Risk of damage to the unit Note that only qualified personnel should be allowed to work on the open unit so the warranty on the device is not affected Authorized SIEMENS maintenance and repair centers offer you a specialist maintenance service The user s guide supplies you with their addresses Caution The electronic components of the printed boards are extremely sensitive to electrostatic discharge When handling the boards precautionary measures must be taken Please refer to the guidelines for electrostatically sensitive components ESD guidelines in the User Manual Section 1 All technical specifications an
21. he display housing e Install the new tube by following the above instructions in reverse order Ensure that the tube socket locks in the display housing correctly Note Always replace both tubes back plate minus screwdriver Figure 1 19 Applying the Screwdriver SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 1 23 System Unit ng marking at the side of lamp unit back plate mon S marking at the metal portion at the side of the module Figure 1 20 Sliding the Tubes In and Out SIMATIC PC BI10 F110 F115 Technical Description 1 24 C79000 G7076 C773 03 System Unit Replacement in The backlight tube for the SVGA TFT display is replaced as follows the SVGA TFT Display Compliance with the ESD guidelines in the Manual Section 1 1 is essential Remove the display from the front plate as described in Section 1 4 3 Lay the display face up on a dust free surface The backlight tube is accessible from the side on the left as viewed from the rear Align the 2 metal lugs at the top edge of the display see Figure 1 21 Remove the 4 screws as shown in Figure 1 22 2 left 2 right Disassemble the rear panel of the display as shown in Figure 1 23 Lift the reflector foil at the top edge of the display and remove the backlight tube carefully Insert the new backlight tube and cover it with the reflector foil The sealing rings O rings on the tube must
22. must not be exerted on the module Therefore do not push down or force the retainers in any way Removing and Proceed as follows Installing an Remove all connectors from the expansion module and write down where Expansion Module they belong e Release the card retainers e Release the screw on the slot plate of the module e Pull the module carefully out of the slot Safecard optional Figure 1 28 Removing and Installing an Expansion Module e DIP switches and jumpers of the new module should be set as those of the old module provided that both modules are of the same type and version in any other case refer to the corresponding documentation of your module Proceed in reverse order to install a new expansion module SIMATIC PC BI10 F110 FI15 Technical Description C79000 G7076 C773 03 1 31 System Unit 1 4 10 Removing and Installing the Bus Board e Open the system unit as described in Sectio e Remove_all modules from the slots proceed as described in Section 1 4 9 49 e Release the screws on the exterior of the system housing and pull the bus board out of the mother board Figure 1 29 Removing and Installing the Bus Board e Proceed in reverse order to install the bus board SIMATIC PC BI10 F110 F115 Technical Description 1 32 C79000 G7076 C773 03 System Unit 1 4 11 Removing and Installing a Fan Ope
23. n the system unit as described in Sectio In the case of the BI10 and FI10 remove the floppy disk drive first as described in Sections 1 4 6 h nd 1 4 7 respectively The fan is fixed to the system housing with two plastic rivets Remove the rivets by pressing the thorns out of the body of the rivet from behind Disconnect the connector for the fan cable at the power supply and lift the fan out Figure 1 30 Removing and Installing the Fan Proceed in reverse order to install the fan Note You must install a fan of the same type SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 1 33 System Unit 1 4 12 Removing and Installing the Power Supply Unit e Open the system unit as described in Sectio e Disconnect all connecting cables and write down their previous connections Figure 1 31 Removing and Installing the Power Supply Unit e Release the three screws on the fan side of the computer housing and the screw on the port side see Figure 1 31 e Lift the power supply unit slightly and disconnect the connecting cable from the mother board underneath the power supply unit To install the power supply proceed in reverse order Mains Voltage The 90 W power supply unit for the SIMATIC PC BI10 FI10 FI15 is Changeover designed for AC input voltages of 120V 240V 6 10 and input currents of 1 4A 0 8A for A
24. nstalling a Fan 0 cece eee ees 1 4 12 Removing and Installing the Power Supply Unit 1 4 13 Removing and Installing the CPU Board 00 2 0c cece eee 1 4 14 Connecting the MPI DP Interface 0 00 cee eee ee 1445 Reset BURON 2c sie hsek Gaga eh eee eee ees ees 1 5 Error DIAGMOSUCS s ccc oreeedcdoteued ena eandegd dened snares des 2 Mother Board 00 06 ies eee eee cette eee a eee ees eset ee a tec ene 2 1 Overview of the Components 060 cc cece e eee eee 2 2 PIOCCSSOF ace enc town hi ea a hat nike pbi deka eae nih Dede A 2 3 Graphics Interface Module 000 cece eee eee eee eee 2 4 MEMO eeiic eco ed hence shone eek adden edhe Mone E eae 2 5 Changing the Backup Battery 000 cece eee eee eee 2 6 Block Diagram of the Mother Board 0c cece eee eee 2 7 Hardware Ports s ncndieciaes oda dane de ii pi udier dinnada ia no aaa 2 8 Hardware Addresses 0 00 c cece tte tenet eee 2 9 Interrupt and DMA Assignments 00000 eee ees 2 10 SEUD neseno bni aE adhe he din haan adits 210 1 Mam Menu ss sine ame tat peta i n glen eo iee engin E E A 2 10 2 Advanced Menu 0 iddi eni ika eet eet eens 2 10 3 Security Menu ies denian anka tenets 2 10 34 POW6rMCNU Meise ers cei ane E erie E E eee de e ted 2109 Ext M6nU rsrsrsrsrs iran AARAA RANEA eatenn agers SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773
25. or NS 16550 compatible LPT1 Parallel port Standard EPP and ECP mode for printer with parallel port VGA VGA interface for external monitor Keyboard PS 2 keyboard connection Mouse PS 2 mouse connection MPI DP interface isolated 9 pin sub D socket screw type locking Transmission rate 9 6 Kbps to 1 5 Mbps assign parameters by software Operating mode isolated data lines A B control lines RTSAS RTS_PG 5V line voltage max 90 mA ground connection MPI DP connection cable shield Physicalinterface RS485 optically isolated PMCIA interface PCMCIA 2 1 JEIDA 4 1 compatible Function display LEDs on FI10 FI15 Power Diskette Run with SafeCard only Temp with SafeCard only LEDs on BI10 Disk Isolation within the low voltage safety circuit SELV Tn the case of an installed direct key module only a short ISA module can be fitted 1 4 SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 System Unit 1 2 Information on Dimensions of Expansion Modules The SIMATIC PC FI10 FI15 and BI10 are designed for modules according to AT PCI specification The size of the modules has to be within the range of Modules dimensions indicated Any deviation in their height can cause problems of contacting functional disorders or difficulties during their installation hea 290 ee F a oN ot Q of A31 Al 2 5
26. orks via the optically isolated MPI DP interface The physical connection is established via SINEC L2 components for stationary links or via an MPI connecting cable with a length of 5 meters for non stationary links Order No 6ES7001 OBF00 0AA0 SINEC L2 components and MPI connecting cables are not included with the PC and have to be ordered separately The MPI connecting cable 5m can only be employed for data transfer rates up to 187 5 Kbps To connect your IPC to a PROFIBUS DP network proceed as follows 1 Switch off your IPC by removing the power supply plug 2 Plug the connecting cable of the SINEC L2 components or the MPI connecting cable into the MPI DP socket connector of your PC and tighten the connector by means of screw type locking 3 Switch on your IPC by removing the power supply plug Caution Risk of damage to the unit Before plugging in the connecting cables you must discharge the electro static charge of the cables and of your body by briefly touching a grounded object ESD guideline You can network up to 32 devices PC PG PLC or DP components via the MPI DP interface in one segment The interconnection to the PROFIBUS DP segments is established via an optically isolated RS 458 port which is part of the interface Interconnect several PROFIBUS DP segments via a repeater The entire PROFIBUS DP network has a maximum capacity of 127 stations The data transfer rate of the MPI network is 18
27. propriate channels see Figure 1 17 e Reassemble the rear panel of the display see Figure 1 18 and replace the 6 screws e Turn the 17 metal lugs back to the original skewed position e Check that the tube functions correctly SIMATIC PC BI10 F110 F1I15 Technical Description C79000 G7076 C773 03 System Unit Figure 1 15 Removing the Screws and Metal Hooks Vi reflector film back plate Figure 1 16 Removing the Tube SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 1 21 System Unit 1 22 cables cable positioning Figure 1 17 Position of the Tube Cables o Ring at both ends As sheet reflector film reflector film back plate Figure 1 18 Reassembly SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 System Unit Replacement in The backlight tube for the VGA TFT display is replaced as follows me VOA TET e Compliance with the ESD guidelines in the Manual Section 1 1 is Display essential e Remove the display from the front plate as described in Section 1 4 3 Lay the display face up on a dust free surface e The backlight tubes are accessible from the side on the left as viewed from the rear e Prise the white plastic tube socket out of the display housing using a medium sized slot screwdriver Holding the plastic not the cable pull the tube together with the socket carefully out of t
28. re defined as persons who are authorized to commission to ground and to tag cir cuits equipment and systems in accordance with established safety practices and standards Note the following Warning This device and its components may only be used for the applications described in the cata log or the technical description and only in connection with devices or components from other manufacturers which have been approved or recommended by Siemens This product can only function correctly and safely if it is transported stored set up and installedcorrectly and operated and maintained as recommended SIMATIC SIMATIC NET and SIMATIC HMI are registered trademarks of SIEMENS AG Third parties using for their own purposes any other names in this document which refer to trademarks might infringe upon the rights of the trademark owners Copyright Siemens AG 1998 All rights reserved The reproduction transmission or use of this document or its contents is not permitted without express written authority Offenders will be liable for damages All rights including rights createdby patent grantor registration of a utility model or design are reserved Siemens AG Bereich Automatisierungs und Antriebstechnik Geschaeftsgebiet Industrie Automatisierungssysteme Postfach 4848 D 90327 Nuernberg Disclaimer of Liability We have checked the contents of this manual for agreement with the hardware and software described Since
29. the Fixed disk function in SETUP Keyboard stuck key failure message appears A key has become blocked during the system keyboard self test Check the keyboard Restart the system Booting of the PC aborted after several beeps An error has occurred during the systemself test Check the hardware see also Chap 2 12 Every time a key is pressed a beep is heard and no characters appear Keyboard buffer overflow lt CTRL gt lt PAUSE gt Not ready message when trying to write to a diskette No diskette has been inserted Diskette has not been formatted Insert diskette Format diskette Write protect error when trying to write to a diskette Diskette write protect activated Write protect hole open on 3 5 diskette Cancel write protection COM1 COM2 LPT1 or MPI DP do not respond Ports have been disabled in SETUP Enable COM1 COM2 LPT1 or MPI DP in SETUP under submenu Hardware Options lt gt key is not displayed Wrong keyboard driver is being used Load correct keyboard driver lt ALT gt lt 9 gt lt 2 gt Mouse not working Trackball does not rotate No or wrong mouse driver is used Clean trackball and housing Load correct mouse driver Mouse pointer cannot be moved PS 2 port has been disabled in SETUP Check SETUP settings Mouse pointer moving erratically Trackball dirty Clean trackball and housing Driv
30. ve in the FI10 Note The disk drive can be installed in the system housing rotated by 90 This is necessary with a mounting position in which the network connection is at the top The disk drive should not be operated with the disk slot at the bottom In this case after removing the disk drive remove the angle bracket and the tag and screw them onto the opposite points on the drive support Install the disk drive and ensure that the previous orientation of the floppy disk drive is retained that is the disk drive cable must be fed in from below SIMATIC PC BI10 F110 F115 Technical Description C79000 G7076 C773 03 1 27 System Unit 1 4 7 Removing and Installing the Floppy Disk Drive in the F115 Open the system unit as described in Section 1 4 1 Release the two screws that fix the disk drive support to the system housing e Pull the disk drive support backwards out of the front plate e Release the two screws which fix the floppy disk drive to the support and remove the drive from the support e Release the locking mechanism for the controller cable at the disk drive and pull the cable out of the connector e Follow the above instructions in reverse order to install the new drive The new drive must be of the same type as the drive you removed Figure 1 25 Installing the Floppy Disk Drive in the FI15 SIMATIC PC

Displays

Contents

Download Pdf Manuals

Related Search

Related Contents