XPEED Outdoor Series Ver 1.0
Contents
1. e RED ADJUST 0 255 BLUE ADJUST 0 255 4 OSD Menu m AUTO EXPOSURE SETUP XPEED Outdoor Series WWW CNBTEC COM e BACKLIGHT OFF C1 C2 L1 L2 U1 U2 D1 D2 R1 R2 Sets Backlight Compensation AUTO EXPOSURE SETUP gt BACKLIGHT DAY NIGHT SLOW SHUTTER below Note 1 AE MODE DAY NIGHT AUTO DAY NIGHT elRIS LEVEL eGAIN LEVEL e SLOW SHOUTTER OFF 2 128 Field eSHUTTER SPD Activates SLOW SHUTTER function when luminance of image signal is too dark BRIGHTNESS BACK EXIT SLOW SHUTTER function It is only available when DAY NIGHT mode is DAY e AE MODE AUTO SHUTTER IRIS AGC MANUAL There are five modes of Auto Exposure function Except AUTO mode the others can be selected when DAY NIGHT mode is DAY and Slow Shutter mode is OFF The reference position and the level of BLC are selectable Refer to the table It is possible to set up the maximum number of fields piled up one on another by e IRIS LEVEL 0 255 It can be set when AE is in IRIS mode or MANUAL mode e GAIN LEVEL 0 255 It can be set when AE is in AGC mode or MANUAL mode e SHUTTER SPEED 0 27 It can be set when AE is in SHUTTTER SPEED mode or in MANUAL mode As for setting value refer to the table below Note e BRIGHTNESS 0 96 It can be set when AE is not in MANUAL mode Backlight Compensation Low weight at the center of the screen High weight at the center of the screen Low weight at the left of the screen High weight at the left of2. sec high speed pan Tilt Movement e Using Vector Drive Technology Pan Tilt motions are accomplished in a shortest path As a result time to target view is reduced dramatically and the video on the monitor is very natural to watch e For jog operation using a controller since ultra slow speed 0 05 sec can be reached it is very easy to locate camera to desired target view Additionally it is easy to move camera to a desired position with zoom proportional pan tilt movement m Preset Pattern Swing Group Privacy Mask and More Max 127 Presets are assignable and characteristics of each preset can be set up independently such as white Balance Auto Exposure Label Digital Outputs and so on Max 8 set of Swing action can be stored This enables to move camera repetitively between two preset positions with designated speed Max 4 of patterns can be recorded and played back This enables to move camera to follow any trajectory operated by joystick as closely as possible Max 8 set of Group action can be stored This enables to move camera repetitively with combination of preset or pattern or Swing A Group is composed of Max 20 entities of Preset Patten Swings Privacy Masks are assignable not to intrude on other s privacy 8 Privacy Zones gt Only available with Models S2465N P X S2965N P X SCN 22Z27F SCN 23227F option PTZ Pan Tilt Zoom Control With RS 485 communication Max 255 of cameras can be
3. Using OSD Menu See the section how to use OSD Menu Method 1 lt Run Pattern gt Pattern NO gt ex Run Pattern 2 lt Run Pattern gt 2 Method 2 lt Go Preset gt Pattern NO 130 ex Run Pattern 2 lt Go Preset gt 132 Use OSD menu to delete a Pattern XPEED Outdoor Series WWW CNBTEC COM Group e Function The group function allows running sequence of Presets Pattern and or Swings Max 8 group can be stored Each group can have max 20 action entities which can be preset pattern or swing Preset speed can be set up and the repeat number of pattern amp Swing can be set up in Group setup Dwell time between actions can be set up also Dwell time ee amar vel Pattern p mvemeeeeen a i i i I i I i 1 ese I i max 20 Entities Setting Group Use OSD Menu to create a Group e Run Group 1 lt Run Pattern gt Group No 20 gt ex Run Group7 lt Run Pattern gt 27 2 lt Go Preset gt Group No 150 gt ex Run Group7 lt Go Preset gt 157 Deleting Group Use OSD Menu to delete Other Functions e Power Up Action This function enables to resume the last action executed before power down Most of actions such as Preset Pattern Swing and Group are available fort his function but Jog actions are not available to resume e Auto Flip In case that tilt angle arrives at the top of tilt orbit 90 the zoom module camera pans180 to keep tracing targets If this function is set to OFF
4. tilt movement range is 0 95 e Park Action This function enables to locate the camera to specific position automatically if operator doesn t operate the controller for a while The park Time can be defined as an interval from 1 minute to 4 hours e Alarm I O 4 Alarm Inputs and 2 Alarm Outputs Relay output are used If an external sensor is activated camera can be set to move to corresponding preset position Also the output relay can be matched to some specific preset positions to do counteractions such as turning on the light or sounding the alarm It is noted that the latest alarm input is effective if multiple sensors are activated e Privacy Zone Mask To protect privacy Max 8 Privacy Masks can be created on the arbitrary position to hide objects such as windows shops or private house With Spherical Coordinates system powerful Privacy Zone Mask function is possible This function is only available with S2465N P X S2665N P X S2965N P X and SCN 22Z27F SCN 23Z27F P Option e Global Local WB White Balance and AE Auto Exposure can be set up independently for each preset There are 2modes Global mode amp Image Setup Local Mode The Global mode means that WB or AE can be set up totally and simultaneously for all presets in ZOOM CAMERA SETUP menu The Local mode means that WB or AE can be set up independently or separately for each preset in each preset setup menu Each Local WB AE value should activate correspondin
5. ICR 36x Day Night ICR EQ OLOIZI EX view HAD CCD Super HAD CCD II EX view HAD CCD Aaa Gas ol S2465NXW SCN 22Z27FW S2965NXW S2465PXW SCN 23Z27FW S2965PXW Pendant Mount Type Without Sun Shield S2465NXP SCN 22Z27FP S2965NXP S2465PXP SCN 23Z27FP S2965PXP mg SS2465NXW SDN 22Z27FW SS2965NXW SS2465PXW SDN 23Z27FW SS2965PXW Pendant Mount Type With Sun Shield SS2465NXP SDN 22227FP SS2965NXP SS2465PXP SDN 23227FP SS2965PXP S Dome Camera Without Sun Shield S Dome Camera With Sun Shield S2465NX S2465PX SS2465NX SS2465PX SCN 22227F SCN 23227F SDN 22227F SDN 23227F S2965NX S2965PX SS2965NX SS2965PX Related Accessories SWB2000 SPB2000 SCB2000 SOB2000 SSS2000 XPEED Outdoor Series WWW CNBTEC COM MEMO
6. TITLE CAMERA ID PRESET LABEL ALARM I O lt SET NORTH DIRECTION gt PTZ INFORMATION lt PRIVACY ZONE gt BACK e ACTION TITLE EXIT e PRESET LABEL e ALARM I O COMPASS DIRECTION SETUP SET NORTH DIRECTION MOVE TO TARGET POSITION NEAR SAVE FAR CANCEL If an item is set to be AUTO the item is displayed only when the value of it is changed ON OFF ON OFF AUTO ON OFF AUTO ON OFF AUTO ON OFF AUTO Set North to assign compass direction as criteria Move camera and press NEAR button to save Series XPEED Outdoor Series WWW CNBTEC COM 4 OSD Menu Privacy Zone Mask Setup Models S2465N P X S2965N P X SCN 22Z27F SCN 23Z27F Option Only PRIVACY ZONE Select area in image to mask gt MASK NO 1 UNDEFINED DISPLAY OFF e MASK NO 1 8 CLEAR MASK CANCEL Select Mask number If the selected mask has already data camera moves as it lt EDIT MASK gt was set Otherwise UNDEFINED will be displayed under MASK NO e DISPLAY ON OFF Sets if camera makes mask shows or not on images e CLEAR MASK CANCEL OK Deletes data in the selected mask NO Privacy Zone Area Setup Move camera to the area to mask EDIT MASK 1 a Then the menu to adjust mask size will be displayed MOVE TO TARGET POSITION NEAR SELECT FAR CANCEL Privacy Zone Size Adjustment XPEED Outdoor Series WWW CNBTEC COM Camera Setup Model SCN 22227F SCN 23227
7. data press FAR key NEAR SAVE FAR DELETE 0 0 x1 N 4 OSD Menu Group Setup GROUP SETUP e GROUP NO 1 8 gt GROUP NO 1 Selects a group number If the selected number is not set UNDEFINED will be UNDEFINED CLEAR GROUP CANCEL displayed selected Group number lt EDIT GROUP gt e CLEAR GROUP CANCEL OK Clears the current setting of a group e EDIT GROUP Starts editing Group EDIT GROUP Press NEAR key in NO list to start Group setup EDIT GROUP 1 NO ACTION DWELL OPT NONE NONE NONE NONE NONE SAVE CANCEL NEAR EDIT XPEED WWW CNBTEC COM EDIT GROUP 1 NO ACTION DWELL OPT gt NONE NONE NONE NONE NONE SAVE NEAR EDIT ACT CANCEL FAR EDIT END EDIT GROUP 1 NO ACTION DWELL OPT NONE NONE NONE NONE NONE SAVE 4 gt MOVE CURSOR CANCEL A Y CHANGE VAL 4 OSD Menu EDIT GROUP 1 NO ACTION DWELL OPT PRESET 1 00 03 360 NONE NONE NONE NONE SAVE 4 gt MOVE CURSOR CANCEL A CHANGE VAL EDIT GROUP 1 NO ACTION DWELL OPT PRESET 1 00 03 360 NONE NONE NONE NONE SAVE NEAR EDIT ACT CANCEL FAR EDIT END Outdoor Series Note that MAX 20Functions are allowed in a Group Move cursor up down and press NEAR key to set up Set up Action Dwell time and Option Note that selected item is displayed in reverse Move cursor Left Right to select items and move cursor Up Down to change
8. each value e ACTION NONE PRESET SWING PATTERN e DWELL 0 sec 4min Sets Dwell Time between functions e OPT Option It should be preset speed when preset is set in Action Is should be the number of repeat when Pattern or Swing is selected in Action Set up items such as Action Dwell and OPT After finishing setting up a Action press NEAR key to one upper Level Menu Step Move cursor Up Down to select Action Number and repeat Step Step to edit selected Group XPEED Outdoor Series WWW CNBTEC COM After Finishing setting up all Action press FAR key to exit EDIT GROUP 1 Then cursor should be moved to SAVE Press NEAR key to save data NO ACTION DWELL OPT PRESET 1 00 03 360 NONE NONE NONE NONE gt SAVE CANCEL 4 OSD Menu System Initialize CLEAR ALL DATA Deletes all configuration data such as display camera motion setup and so SYSTEM INITIALIZE on gt CLEAR ALL DATA eCLR DISPLAY SET a E e CLR DISPLAY SET Initializes Display Configuration eCLR EDIT DATA REBOOT CAMERA REBOOT SYSTEM e CLR CAMERA SET Initializes camera Configuration e CLR MOTION SET Initializes Motion Configuration e CLR EDIT DATA Deletes Preset Data Swing Data Pattern Data and Group Data REBOOT CAMERA Reboots Zoom Camera module REBOOT SYSTEM Reboots Speed Dome Camera m Initial setting e Camera setting e Display setting XPEED Outdoor Series W
9. idealistic mechanical design protects camera from water and dust IP 66 e It is easy to install and maintain camera with terminal for cable connection in brackets XPEED Outdoor Series WWW CNBTEC COM 1 Introduction Product amp Accessories Basic Components e Dome Cover AC Adaptor option Main Body Main Body Sun Shield L Style TORX Wrench es Manua Camera Bracket amp Bracket Accessories or Wall Mount Bracket Rubber Gasket Anchor Bolt Rubber Gasket Anchor Bolt Allen Hex Wrench Other Components available to be ordered separately XPEED Outdoor Series WWW CNBTEC COM IIIS IIIS Pole Mount Adapter Sems Screw Corner Mount Adapter Gann Scran 1 Introduction Parts Name amp Functions 9 TACT Switch nn Main Body Screw Cable 2 DIP Switch Cabling Mold Line Terminal Block Main Body 6 Fuse Cable Drop Prevention 1 Dome Cover Sping lt Main Body gt lt Mounting Bracket gt Dome Cover Do not detach protection vinyl from dome cover before finishing all installation process to protect dome cover from scratches or dust DIP Switch Sets up camera ID and protocol Main Body Enables signals and power to come and go between main body and mount bracket Cable Drop Prevention This part keeps the camera from dropping during installation and maintenance After install the Bracket please hang Spring the spring to the drop prevention hook of
10. main body as shown in picture for further tasks Lockup Screw After assembling main body to bracket screw main body to bracket to protect them from separation by vibration and so on Fuse If the fuse is burnt to protect your came from over current damage the fuse have to be replace with new one The fuse specification is 250V 2A however we recommend consulting with supplier to remove the cause of over current Cabling During installation Power Video Communication Alarm I O cables are connected on to this cables terminal block Terminal Block Mold Line Mark to assemble main body to bracket XPEED Outdoor Series WWW CNBTEC COM TACT Switch Network Board Factory reset 2 Installation v Before installing the camera you should set the DIP switches to configure the camera ID communication protocol Do not use the system upgrade terminal DIP Switch Setup a TO BRACKET T B Communication m Protocol D 1 2 3 4 5 6 7 8 PIN pm 16 AO A1 AZ A3 A4 A5 A6 A7 FUNC D O PIN Oh 1 2 4 s 16 32 6428 10 0 0 0 0 o o o Kg oOPTIONS es ADDRESS ID o The example is shown bellow prm ID number of camera is set using binary number row me on or or or or oe ow ore on owe or er or e The range of ID 1 255 Do not use 0 as camera ID e Factory default of Camera ID is 1 e If you want to control a certain camera you must match the camera ID with Cam ID setti
11. the screen Low weight at the upper of the screen High weight at the upper of the screen D Low weight at the lower of the screen High weight at the lower of the screen R Low weight at the right of the screen High weight at the right of the screen Shutter Speed Table The values are based on NTSC type models 4 OSD Menu XPEED Outdoor Series WWW CNBTEC COM Camera Setup Models S2465N P X S2965N P X Setup the general functions of 26x 36x optical Zoom modules ZOOM CAMERA SETUP gt FOCUS MODE SEMIAUTO e FOCUS MODE AUTO MANUAL SEMIAUTO DIGITAL ZOOM ON FLICKERLESS OFF Sets camera focus mode COLOR ON LINE LOCK OFF lt WHITE BALANCE SETUP gt e DIGITAL ZOOM ON OFF lt AUTO EXPOSURE SETUP gt Sets digital zoom on or off BACK EXIT e FLICKERLESS ON OFF When an NTSC camera is used under 50Hz or PAL under 60Hz flickering may appear on the screen When this happens turn Flickerlees setting ON This prevents flickering which happens when the frequency of the power and the frequency of camera are different e COLOR ON OFF Switching color mode to black white mode e LINE LOCK ON OFF If Line lock sync is ON video signal is synchronized with AC power Video can be fluctuated after setting is changed m WHITE BALANCE SETUP e WB MODE AUTO MANUAL In Manual mode Red and Blue level can be setup manually WHITTE BALANCE SETUP gt WB MODE AUTO eRED ADJUST eBLUE ADJUST e RED A
12. DJUST 0 255 e BLUE ADJUST 0 255 XPEED Outdoor Series WWW CNBTEC COM 4 OSD Menu m AUTO EXPOSURE SETUP BACKLIGHT ON OFF Sets Backlight Compensation AUTO EXPOSURE SETUP BACKLIGHT DAY NIGHT AE MODE e DAY NIGHT AUTO DAY NIGHT elRIS LEVEL eGAIN LEVEL eSHUTTER SPD AE MODE AUTO SHUTTER IRIS GAIN BRIGHT MANUAL eBRIGHTNESS Selects automatic exposure mode Each mode appears with adjustable values pn When Flickeress mode is ON AE mode is automatically in SHUTTER SPEED EXIT mode IRIS LEVEL CLOSE F1 6 F28 Model S1465N P X S1965N P X CLOSE F1 4 F22 Model S1665N P X It can be set when AE is in IRIS mode or MANUAL mode GAIN LEVEL 3dB 28dB It can be set when AE is in MANUAL mode SHUTTER SPEED 1 1sec 1 10000sec It can be set when AE is in SHUTTER SPEED mode or MANUAL mode BRIGHTNESS 0 31 It can be set when AE is in BRIGHTNESS mode WDR Only available with S1965N P X Models XPEED Outdoor Series WWW CNBTEC COM 4 OSD Menu Motion Setup Setup the general functions of Pan Tilt motions MOTION SETUP gt MOTION LOCK e MOTION LOCK ON OFF PWR UP ACTION ON AUTO FLIP ON If Motion Lock is set to ON it is impossible to set up and delete Preset JOG MAX SPEED 120 SEC Swing Pattern and Group JOG DIRECTION INVERSE FRZ IN PRESET OFF lt PARKING ACTION SETUP gt enter into OSD menu lt ALARM INPUT SETUP gt BACK EXIT PWR UP ACTION ON OFF Refer
13. F Adjust mask size Use joystick or arrow buttons to adjust mask size EDIT MASK 1 e lt gt Left Right Adjusts mask width e Av Up Down Adjusts mask height 4 ADJUST MASK WIDTH A V ADJUST MASK HEIGHT NEAR SAVE FAR CANCEL 4 OSD Menu XPEED Outdoor Series WWW CNBTEC COM Setup the general functions of 27x optical Zoom camera module e FOCUS MODE AUTO MANUAL SEMIAUTO Sets camera focus mode ZOOM CAMERA SETUP gt FOCUS MODE SEMIAUTO MAX ZOOM X270 FLICKERLESS OFF e MAX ZOOM x1 x270 COLOR ON EE LINE LOCK OFF Sets the maximum zoom magnification lt WHITE BALANCE SETUP gt lt AUTO EXPOSURE SETUP gt e FLICKERLESS ON OFF BACK When an NTSC camera if used under 50Hz and PAL under 60Hz EXIT flickering may appear on the screen When this happens turn FLICKERLESS setting ON This prevents flickering which happens when the frequency of the power and the frequency of camera are different When FLICKERLESS in ON Day amp Night mode goes DAY and Digital Slow Shutter mode goes OFF automatically e COLOR ON OFF Switching color mode to black white mode LINE LOCK ON OFF If Line lock sync is ON video signal is synchronized with AC power Video can be fluctuated after setting is changed m WHITE BALANCE SETUP e WB MODE AUTO MANUAL In Manual mode Red and Blue level can be setup manually WHITTE BALANCE SETUP gt WB MODE AUTO eRED ADJUST eBLUE ADJUST
14. Manual SemiAuto AE Mode Auto Iris Shutter Manual Brightness White Balance Auto Manual Red Blue Gain Adjustable BLC On Off Flickerless Operation Range On Off Pan 360 Endless Tilt 90 Pan Tilt Operation Speed Preset 360 sec Manual 1 360 sec inter locked with zoom extension Swing 1 180 sec XPEED Outdoor WWW CNBTEC COM Preset Setting 127 presets label setting individual video setting Swing Setting 8 swings Pattern Setting 4 pattern 1200 commands pattern 5 min Group Setting 8 groups 20 actions group Other Functions Auto Flip Auto Parking Power Up Action Communication RS 485 Protocol Pelco D Pelco P Samsung and Panasonic Selectable Privacy Zone 8 Zones Alarm I O 4 inputs 2 outputs OSD Menu On Off Input Voltage 24VAC 19VAC 29VAC sengral Input Power 48VA Fuse 2A Dome 149 Dimension Housing 209 7 x 247 2 H mm without Sun Sheild Weight Approx 3 8kg without Sun Sheild 4 3kg with Sun Sheild Operational Temperature 30 C 50 C 5 Specifications 27x Models SCN 22227F SCN 23227F Video Signal NTSC PAL Image Pick up Device 1 4 IT CCD Effective Pixels 811 H x 508 V 410K 795 H x 596 V 470K Horizontal Resolution 768 H x 494 V 380K 752 H x 582 V 440K Resolution 580 TV Lines BW 600 TV Lines Shar
15. ON HOME PRESET PATTERN SWING GROUP If it is set to HOME all the functions go back to HOME position PAN TILT ZOOM 0 0 x1 XPEED Outdoor Series WWW CNBTEC COM 4 OSD Menu ALARM ACTION SETUP Sets the preset to move to when the alarm is input ALARM ACTION SETUP gt ALARM1 ACT NOT USED e ALARM N ACT NOT USED PRESET 1 128 ALARM2 ACT NOT USED T ALARM3 ACT NOT USED ALARM4 ACT NOT USED Assign counteraction Preset position to each Alarm input ___ The uppercase N indicates the alarm index Preset Setup PRESET NO 1 128 If a selected preset is already defined camera moves to pre defined position PRESET SETUP NO and preset characteristics such as Label and Relay Outputs show on monitor CLR PRESET CANCEL If a selected preset is not defined UNDEFINED shows on monitor lt EDIT SCENE gt lt EDIT LABEL gt LABEL123 lt RELAY OUT gt i e CLR PRESET CANCEL OK CAM ADJUST GLOBAL Delete current Preset data BACK EXIT e EDIT SCENE Redefine current Preset scene position i e PTZ EDIT LABEL Edits Label to show on monitor when preset runs MAX 10 alphabets are allowed e RELAY OUT Sets the relay output The figure on the right is current Setting value indicates OFF mode If the relay is shown as figures it means relay is ON e CAM ADJUST GLOBAL LOCAL WB White Balance and AE Auto Exposure can be set up independently for each preset There are 2 mode
16. SD Menu Input Voltage On Off 24VAC 19VAC 29VAC Siete Input Power 48VA Fuse 2A Dimension Weight Approx Dome 149 Housing 209 7 x 247 2 H mm without Sun Sheild 3 8kg without Sun Sheild 4 3kg with Sun Sheild Operational Temperature 5 Specifications 30 C 50 C 36x EXview Models S2965NX S2965PX Video Signal NTSC PAL Image Pick up Device 1 4 EXview HAD CCD Effective Pixels 768 H x 494 V 380K 752 H x 582 V 440K Horizontal Resolution 530 TV Lines S N Ratio 50 dB Weight ON Zoom 36x Optical Zoom 12x Digital Zoom Focal Length f 3 4 Wide 122 4 Tele mm Aperture Range F1 6 Wide 4 5 Tele Camera 1 4 Lux 1 60 sec NT 1 50 sec PAL Minimum Illumination 0 1Lux 1 4 sec NT 1 3 sec PAL 0 01Lux 1 4 sec NT 1 3 sec PAL ICR ON White Balance Day amp Night Auto Day Night WDR Focus Auto Manual SemiAuto AE Mode Auto Iris Shutter Manual Brightness Auto Manual Red Blue Gain Adjustable BLC On Off WDR Series Types by installation Pendant Mount Wall Mount Sun Shield XPEED Outdoor WWW CNBTEC COM Flickerless On Off Operation Range Pan 360 Endless Tilt 90 Preset 360 sec Operation Speed Manual 1 360 sec inter locked with zoom extension Swing 1 180 s
17. WW CNBTEC COM Camera ID ON Focus mode SemiAuto PTZ Information AUTO Digital Zoom e ON Action Title AUTO Preset Label AUTO Alarm I O AUTO Color Max Zoom Flickerless a x312 x432 e North Direction Pan 0 Line Lock Undefined White Balance Privacy Zone amp er Backlight Day amp Night Slow Shutter AE Mode Brightness e Motion setting e User setting data Preset 1 128 Undefined Motion Lock Power up Action ON Swing 1 8 Undefined Auto Flip ON Pattern 1 4 Undefined 120 sec INVERSE Jog Max Speed Group 1 8 Undefined Jog Direction Park Action OFF Alarm Action OFF FRZ IN PRESET ee OFF B Above functions are only available with the following models amp S2465N P e _ S2965N P X SCN 22Z27F SCN 23Z27F P Option 5 Specifications 26x EXview Models S2465NX S2465PX Video Signal NTSC PAL Image Pick up Device 1 4 EXview HAD CCD Effective Pixels 768 H x 494 V 380K 752 H x 582 V 440K Horizontal Resolution S N Ratio 470 TV Lines 460 TV Lines More than 50 db Zoom 26x Optical Zoom 12x Digital Zoom Focal Length f 3 5 Wide 91 Tele mm Aperture Range F1 6 Wide 3 8 Tele Camera Minimum Illumination 1 0Lux Color 0 07Lux Color DSS 0 15 Lux B W DSS Day amp Night Auto Day Night IR Cut Filter Focus Auto
18. an be configured for each application e Enter Menu lt Go Preset gt 95 Reserved Preset e Description Some Preset numbers are reserved to special functions e Function 1 lt Go Preset gt 95 Enters into OSD menu 2 lt Go Preset gt 131 134 Runs pattern function 1 4 3 lt Go Preset gt 141 148 Runs Swing Function 1 8 4 lt Go Preset gt 151 158 Runs Group Function 1 8 3 Operation XPEED WWW CNBTEC COM Preset Function e Set Preset Run Preset Delete Preset Swing e Function e Set Swing e Run Sing e Deleting Swing Pattern Function e Setting Pattern e Run Pattern Delete Pattern 3 Operation Outdoor Series Max 127 positions can be stored as Preset position The Preset number can be assigned from 1 to 128 but 95 is reserved for starting OSD menu Camera characteristics i e White Balance Auto Exposure can be set up independently for each preset Label should be blank and Relay Outputs should be set to OFF as default Camera Adjust should be set GLOBAL as default All characteristics can be set up in OSD menu lt Set Preset gt 1 128 lt Go Preset gt 1 128 To delete Preset use OSD menu By using Swing function you can make camera to move between 2 Preset positions repeatedly When swing function runs camera moves from the preset assigned as the 1st point to the preset assigned as the 2nd point in CW Clockwise directio
19. cd efghijkl mn opqrstuv wx yz lt gt g Back Space Char Space Char If you want to use blank choose Space character If you want To delete a character before use back space character lt If you complete the Label editing move cursor to OK and press NEAR key to save completed label To abort current change move cursor to Cancel and press NEAR key EDIT RELAY OUT XPEED Outdoor Series WWW CNBTEC COM e RELAY OUT N ON OFF RELAY OU PRESET 1 RELAY OUT 1 Sets relay output when changing preset position RELAY OUT 2 The uppercase N indicates the number for the preset 4 OSD Menu Swing Setup e SWING NO 1 8 SWING SETUP Selects Swing number to edit If a selected Swing has not defined NOT USED is gt ENING NO k displayed in 1st Position and 2nd Position 1ST POS NOT USED 2ND POS NOT USED e 1ST POS PRESET 1 128 SWING SPEED 30 SEC a CLEAR SWING CANCEL 2ND POS Set up the 2 position for Swing function If a selected preset is not defined UNDEFINED will be displayed as shown below SWING SETUP SWING NO 1 1ST POS 2ND POS NOT USED gt UNDEFINED When swing function runs camera moves from the preset assigned as the 1st point to the preset assigned as the 2nd point in CW Clockwise direction Then camera moves from the preset assigned as the 2nd point to the preset assigned as the 1st point is CCW Counterclo
20. ckwise direction In case that the preset assigned as the 1st point is same as the preset assigned as the 2nd point camera turns on its axis by 360 in CW direction and then it turns on its axis by 360 in CCW direction e SWING SPEED 1 sec 180 sec Sets Swing speed from 1 sec to 180 sec e CLEAR SWING CANCEL OK Deletes current Swing data XPEED Outdoor Series WWW CNBTEC COM 4 OSD Menu Pattern setup PATTERN NO 1 4 Selects Pattern number to edit If a selected pattern number is not defined PATTERN SETUP gt PATTERN NO 1 UNDEFINED CLR PATTERN CANCEL lt EDIT PATTERN gt e CLR PATTERN CANCEL OK Deletes data in current pattern UNDEFINED will be displayed under selected pattern number e EDIT PATTERN Starts editing pattern EDIT PATTERN EDIT PATTERN 1 7 By using Joystick move to start position with appropriate zoom To start pattern recording press NEAR key To exit this menu press FAR key MOVE TO START POSITION NEAR START FAR CANCEL XPEED Outdoor Series WWW CNBTEC COM EDIT PATTERN 1 TIITII Move camera with joystick of controller or run preset function to memorize the path mostly curve path in a selected pattern The total memory size and the rest memory size is displayed in the form of bar Maximum 1200 communication commands can be stored in a pattern To save data and exit press NEAR key To cancel recording and delete record
21. controlled at the same time e Pelco D Pelco P Samsung or Panasonic protocol can be selected as a control protocol in the current version of firmware mOSD On Screen Display Menu XPEED Outdoor Series WWW CNBTEC COM e OSD menu is provided to display the status of camera and to configure the functions interactively The information such as Camera ID Pan Tilt Angle Alarm I O and Preset can be displayed on screen B Alarm I O Functions e 4 alarm sensor inputs and 2 alarm Output relays are available e To reject external electric noise and shock perfectly alarm sensor Input is decoupled with photo coupler and the relay is used for alarm output e The signal range of sensor input is from DC 5 0 to 12 0 volts to adopt various applications Meanwhile the maximum load of relay contact is 250VAC 3A or 28VDC 3A e If an external sensor is activated camera con be set to move to the corresponding Preset position Meanwhile the output relay can be matched to some specific preset positions to do counteractions such as turning on the light or sound the alarm E Reserved Presets for Special Purpose e Most camera characteristics can be set up easily and directly with reserved preset not entering into OSD menu For more information refer to Reserved Preset in this manual B Easy Installation and Perfect Outdoor Environment Compatibility e Fans and heaters are built in camera for cold and hot temperature environment Also
22. d be operated only from the type of power source indicated on the marking label Precautions m Operating Before using make sure power supply and others are properly connected While operating if any abnormal condition or malfunction is observed stop using the camera immediately and then contact your local dealer B Handling Do not disassemble or tamper with parts inside the camera do not drop or subject the camera to shock and vibration as this can damage camera Care must be taken when you clean the clear dome cover Especially scratch and dust will ruin your quality of camera E installation and Storage Do not install the camera in areas of extreme temperature which exceed the allowable range Avoid installing in humid or dusty places Avoid installing in places where radiation is present Avoid installing in places where there are strong magnetic fields and electric signal Avoid installing in places where the camera would be subject to strong vibrations Table of Contents XPEED Outdoor Series WWW CNBTEC COM 1 Introduction Features 4 Product amp Accessories 6 Parts Name amp Functions 7 2 Installation Dip Switch Setup 8 Installation Using the Wall Mount 11 Installation Using the Pendant Mount 12 Wire Connections gt gt gt gt B 3 Operation Check Points before Operation 15 Preset and Pattern Function Pre Check 15 Starting OSD Menu 15 Reserved Pres
23. e camera ID of the controller must be identical to that of the target camera The camera ID can be checked by reading DIP switches of the camera e If your controller supports multi protocols the protocol must be changed to match to that of the camera e If you changed camera protocol by changing DIP switches the change will be effective after you reboot the camera e Since the operation method can be different for each controller available refer to the manual for your controller if camera can not be controlled properly The operation of this manual is based on the standard Pelco Controller Preset and Pattern Function Pre Check e Check how to operate preset and pattern function with controller or DVR in advance to operate camera function fully when using controller or DVR e Refer to the following table when using standard Pelco protocol controller Input Preset Number and press Preset button shortly lt Set Preset gt Input Preset Number and press Preset button for more than 2 seconds lt Run Pattern gt Input Pattern number and press Pattern button shortly lt Set Pattern gt Input Preset Number and press Pattern button for more than 2 seconds e If controller or DVR has no pattern button or function use shortcut keys with preset numbers For more information refer to Reserved Preset in this manual Starting OSD Menu e Function Using the OSD menu Preset Pattern Swing Group and Alarm I O function c
24. ec Pan Tilt Preset Setting 127 presets label setting individual video setting Swing Setting 8 swings Pattern Setting 4 pattern 1200 commands pattern 5 min Group Setting 8 groups 20 actions group Other Functions Auto Flip Auto Parking Power Up Action Communication RS 485 Protocol Pelco D Pelco P Samsung and Panasonic Selectable Privacy Zone 8 Zones Alarm I O 4 inputs 2 outputs OSD Menu On Off Input Voltage 24VAC 19VAC 29VAC ene Input Power A8VA Fuse 2A Dome 149 Dimension Housing 209 7 x 247 2 H mm without Sun Sheild Weight Approx 3 8kg without Sun Sheild 4 3kg with Sun Sheild Operational Temperature 30 C 50 C 5 Specifications Dimensional Drawings Series Types by installation Pendant Mount Pendant Mount Sun Shield Wall Mount Sun Shield XPEED Outdoor Series WWW CNBTEC COM MAIN Body without Sun Sheild MAIN Body without Sun Sheild Weight Approx 3 8kg Weight Approx 4 3kg 175 4 Pandant Mount Bracket Weight Approx 1 9kg 1 1 2 NPT Wall Mount Bracket Weight Approx 1 2kg 165 0 Fer 1A TN LO AN 107 3 Unit mm 5 Specifications XPEED Outdoor Series WWW CNBTEC COM Dimensional Drawings Wall Mount Unit mm qo XPEED Outdoor Series WWW CNBTEC COM 6 System Models amp Related Accessories System Model Numbers 26x Day Night ICR 27x Day Night
25. ermination switch Pin 4 is used in cases listed below Long distance communication between the controller and the camera 1 to 1 connection When the connection distance between the two units is especially long communication errors may occur due to the impedance of transmission cable In this case set the termination switch of both units to ON e Controlling multiple cameras Multiple connection The camera may not operate correctly if multiple cameras are connected and controlled In this case set the termination switch of the controller and the last connected camera to ON and the switch of other cameras is OFF Ex Using the Terminating Resistance Termination Switch ON Termination Switch OFF Termination Switch ON XPEED Outdoor Series WWW CNBTEC COM 2 Installation Installation Using the Wall Mount XPEED Outdoor Series WWW CNBTEC COM Install Wall Mount Bracket on wall Wire cables to terminal blocks on the PCB in Wall Mount Bracket Hook up Drop Prevention Spring on main body to prevent Line up the mold lines and assemble main body to camera from unexpected drop and connect Main Body Wall Mount Bracket Cable to Main Body Connector in Wall Mount Bracket Turn main body on its axis in CW Clockwise direction and after assembling them screw main body to Wall Mount Bracket to protect them from separation by vibration or others In case of using pipe use the hole located on
26. et 15 Preset 16 Swing 16 Pattern 16 Group 17 Other Functions s 4 OSD Menu OSD Display of Main Screen 18 General Rules of key Operation for Menu 19 Main Menu 19 Display Setup 19 Privacy Zone Mask Setup 26x S2465N P X 36x S2965N P X EXview 27x SCN 22227F SCN 23227F Option Models Only 20 Camera Setup 27x SCN 22Z27F SCN 23227F models 21 Camera Setup 26x S2465N P X 36x S2965N P X EXview Models 23 Motion Setup 25 Preset Setup 26 Swing Setup 28 Patten Setup 29 Group Setup 30 System Initialize 32 5 Specifications 26x S2465N P X EXview Models 33 27x SCN 22227F SCN 23227F Models 34 36x S2965N P X EXview Models 35 Dimensional Drawings 36 6 System Models and Related Accessories System Model Numbers 38 Related Accessories 8B 1 Introduction XPEED Outdoor Series WWW CNBTEC COM Features Camera Specifications e Image Pick up Device 1 4 Interline Transfer CCD e Zoom Magnification 26x Optical Zoom 12x Digital Zoom Max 312x Zoom Model S2465N P X 27x Optical Zoom 10x Digital Zoom Max 270x Zoom gt Model SCN 22Z27F SCN 23227F 36x Optical Zoom 12x Digital Zoom Max 432x Zoom Model S2965N P X e Day amp Night Function e Various Focus Mode Auto Focus Manual Focus SemiAuto Focus e Each Preset has its own video configuration label relay output setting values You can adjust each Preset setting independently Powerful Pan Tilt Functions e Max 360
27. gly when camera arrives at each preset location During jog operation Global WB AE value should be applied All Local WB AE value do not change although Global WB AE value changes e SemiAuto Focus This mode exchanges focus mode automatically between Manual Focus mode and Auto focus mode by operation Manual Focus mode activates in preset operation and Auto Focus mode activates during jog operation With Manual mode at preset Focus data is memorized in each preset in advance and camera calls focus data in correspondence with presets as soon as camera arrives at a preset It should shorten time to get focuses Focus mode changes to Auto Focus mode automatically when jog operation starts 4 OSD Menu XPEED Outdoor Series WWW CNBTEC COM OSD Display of Main Screen Preset Label LABEL12345 PRESET 1 Action Title I 1 0 2 Alarm Information Camera ID 15 4 x1 N P T Z information e P T Z Information Current Pan Tilt angle in degree Zoom magnification and a compass direction e Camera ID Current Camera ID Address e Action Title Followings are possible Action Titles and their meaning SET PRESET xxx gt When Preset xxx is stored PRESET xxx gt When camera reach to preset xxx PATTERN x gt When Pattern x is in action SWGx PRESET xxx gt When Swing x is in action UNDEFINED When undefined function is called to run e Preset Label The Label stored for specific Preset Alarm Informati
28. lower side of Wall Mount Bracket to fix pipe 2 Installation Installation Using the Pendant Mount XPEED Outdoor Series WWW CNBTEC COM To pass cables to upside of ceiling Wire cables to terminal blocks on Hook up Drop Prevention Spring on please make a hole with 50 60mm the PCB in Ceiling Mount Bracket main body to prevent camera from unexpected drop and connect Main Body Cable to Main Body Connector in Ceiling Mount Bracket diameter on the ceiling panel and attach the Ceiling mount bracket on it Line up the mold lines and assemble Turn main body on its axis in CW main body to Ciling Mount Bracket Clockwise direction and after assembling them screw main body to Ceiling Mount Bracket to protect them from separation by vibration or others 2 Installation XPEED Outdoor Series WWW CNBTEC COM Wire Connections Sensor input IrDA Sensor a Door Switch O O 24VAC Power COMMON PWR IN1 IN2 IN3 PWR Monitor IN4 VIDEO Video output BNC Illuminati A ion RELAY1 VIDEO RS 485 RELAY2 RS 485 O Relay output Braket Terminal Block Power Connection The standard power for the system is 24VAC 2A Please check the voltage and current capacity of rated power carefully Video Connection e Connect With BNC coaxial cable RS 485 Communication e For PTZ control connect this line to keyboard and DVR To control mul
29. n Then camera moves from the preset assigned as the 2nd point to the preset assigned as the 1st point in CCW Counterclockwise direction O ent gt gt 2nd Preset Se weer s Je a ijn y ay 1st Preset In case that the preset assigned as the 1st point is same as the preset assigned as the 2nd point 1 1 t Camera turns on its axis by 360 in CW Clockwise direction and then it turns on its axis by 360 in CCW Counterclockwise direction Speed can be set up from 1 sec to 180 sec To set Swing use OSD menu Method 1 lt Run Pattern gt Swing NO 10 gt ex Run Swing 3 lt Run Pattern gt 13 Method 2 lt Go Preset gt Swing NO 140 ex Run Swing 3 lt Go Preset gt 143 To delete Swing use OSD menu Pattern Function is that a camera memorizes the path mostly curve path by joystick of controller and preset move functions for assigned time and revives the path exactly as it memorized 4 Patterns are available and Maximum 1200 communication commands can be stored in a pattern Pattern can be created by one of following two methods EDIT PATTERN 1 Method 1 lt Set Pattern gt Pattern NO Pattern editing screen is displayed as bellow Movement by Joystick and preset movement can be memorized in a pattern The rest memory size is displayed in progress bar NEAR SAVE FAR DELETE 0 0 x 1 N To save the recording press NEAR key and to cancel press FAR key Method 2
30. ng of DVR or Controller XPEED WWW CNBTEC COM 2 Installation Communication Protocol Setup Input Sensor Active Type SS Ss amp On EE PEEESS Outdoor Series e Select the appropriate Protocol With DIP switch combination Switch state Protocol Baud rate PO ETIE 1 EET 2 pains 3 ee et ae CEN ee een ECE ee Others Reserved e If you want to control using DVR or P T controller their protocol must be identical to camera Otherwise you can not control the camera t you changed camera protocol by changing DIP S W the change will be effective after you reboot the camera e Factory default of protocol is Pelco D 2400bps e When a sensor input is used its functional type should be set There are two types Normal Open type and Normal Close type Normal Open Voltage is let out when the sensor is activated Normal Close Voltage is let out when the sensor is not activated en Switch position Sensor type ON Sensor 1 Normal Close or Sensor 1 Normal Open ON Sensor 2 Normal Close ST2 Pin 5 or Sensor 2 Normal Open ST1 Pin 4 Sensor 3 Normal Close Sensor 3 Normal Open ST3 Pin 6 XPEED WWW CNBTEC COM m Termination Switch Setting PTZ Controller DVD Termination Switch OFF Outdoor Series PN Sensor 4 Normal Close ST4 Pin 7 Sensor 4 Normal Open e If a wrong type of sensor is selected it activates in the opposite way to the sensor input T
31. on This information shows current state of sensor input and relay output If the Input and output points are ON state it will show a number corresponding to each point When they are OFF state will be displayed Ex point 2 amp 3 of inputs and 1 of output are ON OSD will show as below 4 OSD Menu XPEED Outdoor WWW CNBTEC COM General Rules of key Operation for Menu e The menu items surrounded with lt gt always has its sub menu e For all menu level to go into sub menu press NEAR key e To go to up one level menu press FAR key To move from items to item in the menu use joystick in the Up Down or Left Right e To change a value of an item use Up Down of the joystick in the controller e Press NEAR key to save values and Press FAR key to cancel values e Specifications and functions should be different by models Main Menu SPEED DOME CAMERA e SYSTEM INFORMATION gt lt SYSTEM INFORMATION gt lt DISPLAY SETUP gt e DISPLAU SETUP lt DOME CAMERA SETUP gt lt SYSTEM INITIALIZE gt e DOME CAMERA SETUP e SYSTEM INITIALIZE Display Setup Displays system information and configuration Enable Disable of OSD display on Main Screen Configure various functions of this camera Initializes system configuration and sets all data to factory default configuration DISPLAY SETUP This menu defines Enable Disable of OSD display on main Screen CAMERA ID PTZ INFORMATION ACTION
32. pness Max S N Ratio 50 dB AGC Off Zoom 27x Optical Zoom 10x Digital Zoom Focal Length f 3 6 Wide 97 2 Tele mm Aperture Range F1 6 Wide 3 7 Tele Camera Minimum Illumination 0 5Lux 30 IRE Color 0 1Lux 30 IRE B W DSS 128FLD Mode 0 0005Lux 30 IRE White Balance Day amp Night Auto Day Night Focus Auto Manual SemiAuto Iris Auto Manual Shutter Speed Auto x128 1 60 sec 1 10 000 sec AGC Normal High Off Auto Manual Red Blue Gain Adjustable BLC NORMAL C L U D R HIGH LOW 6 Area Selectable Series Types by installation Pendant Mount Pendant Mount Sun Shield Wall Mount Sun Shield XPEED WWW CNBTEC COM Outdoor Flickerless On Off Brightness Operation Range Adjustable 0 96 Pan 360 Endless Tilt 90 Operation Speed Preset 360 sec Manual 1 360 sec inter locked with zoom extension Swing 1 180 sec Pan Tilt Preset Setting 127 presets label setting individual video setting Swing Setting 8 swings Pattern Setting 4 pattern 1200 commands pattern 5 min Group Setting 8 groups 20 actions group Other Functions Auto Flip Auto Parking Power Up Action Communication RS 485 Protocol Pelco D Pelco P Samsung and Panasonic Selectable Privacy Zone Option 8 Zones Alarm I O 4 inputs 2 outputs O
33. s Global mode amp local mode The Global mode means that WB or AE can be set up totally and simultaneously for all presets in ZOOM CAMERA SETUP menu The local mode means that WB or AE can be set up independently or separately for each preset in each preset setup menu Each Local WB AE value should activate correspondingly when camera arrives at each preset location During jog operation Global WB AE value should be applied All Local WB AE value should not change although Global WB AE value changes If local is selected Menu to set WB AE shows on monitor XPEED Outdoor Series WWW CNBTEC COM 4 OSD Menu m EDIT PRESET SCENE EDIT SCENE PRESET 4 Using Joystick move camera to desired position By pressing NEAR key save current PTZ data Press FAR key to cancel MOVE TO TARGET POSITION NEAR SAVE FAR CANCEL m EDIT PRESET LABEL EDIT LABEL PRESET 1 Edits label to show on monitor when camera arrives at presets In Edit label menu a reverse rectangular is cursor a 1234567890 OK ABC DEFGH I J CANCEL a KLM NOPQRST UVWXYZab cd efghijk tt mn l opqrstuv wx yz lt gt Current Cursor Position As soon as finishing selecting alphabet cursor moves to the next digit Using Left Right Up Down of joystick move to an appropriate character from the Character set To choose that character press the NEAR key 1234567890 ABC DEFGH IJ KLM NOPQRST UVWXYZab
34. tiple cameras at the same time RS 485 communication lines of them is connected in parallel as shown below Keyboard Controller DVR coco o f Wz is oo voo esse so ooo IJS oe oso soo0 2 Installation XPEED Outdoor Series WWW CNBTEC COM m Sensor Input Relay Output e Sensor input connection Internal Circuit 5V 12V IN COM Fi IN 1 Sensor Output1 Ga o K Z A Sensor Output 4 Before connecting sensors check driving voltage and output signal type of the sensor Since output signal types of the sensors are divided into Open Collector and Voltage Output type in general the cabling must be done properly after considering these types Also the sensor type i e Normal Open or Normal Close in DIP switch in main body of camera must be set properly Signal Line Description IN COM Connect cable of electric power source for sensors to this port as shown in the circuit above IN1 IN2 IN3 In4 Connect output of sensors for each port as shown in the circuit above e Relay output connection Internal Circuit AC or DC OUT 1 AC or DC OUT 2 E E Maximum allowable electrical load of relay is shown bellow table Max Capacity 28VDC 3A 110VAC 3A 250VAC 3A 3 Operation XPEED Outdoor Series WWW CNBTEC COM Check Points before Operation e Before power is applied please check the cables carefully Th
35. to Other Functions section It is possible only to run those functions To set up and elete those functions e AUTO FLIP ON OFF Refer to Other Functions section e JOG MAX SPEED 1 sec 360 sec Sets maximum jog speed Jog speed is inversely proportional to zoom magnification As zoom magnification goes up pan tilt speed goes down e JOG DIRECTION INVERSE NORMAL If you set this to Inverse the view in the screen is moving same direction with jog tilting If Normal is selected the view in the screen is moving reversely e FRZ IN PRESET ON OFF 27x 36x Models Only If Freeze in preset function mode is ON camera starts freezing the image of start point at start point of preset movement Camera keeps displaying the image of start point during preset movement and does not display the images which camera gets during preset movement As soon as camera stops at preset end point camera start displaying live images which it gets at preset end point This function is only available with 27x 36x Models PARK ACTION SETUP If Park Enable is set to ON camera runs assigned function automatically if there is no PTZ command PARKING ACTION SETUP during assigned Wait Time gt PARK ENABLE OFF WAIT TIME 00 10 00 PARK ACTION HOME e PARK ENABLE ON OFF e WAIT TIME 1 minute 4 hours The time is displayed with hh mm ss format and you can change this by 1 min unit e PARK ACTI
36. www cnbtec com XPEED Outdoor Series ver 1 0 INSTALLATION AND OPERATION MANUAL 3810 0250A_110119 XPEED Outdoor Series WWW CNBTEC COM This lightning flash with arrowhead symbol is intended to alert The user to the presence of un insulated dangerous voltage Within the product s enclosure that may be of sufficient magnitude To constitute a risk of electric shock to persons This exclamation point symbol is intended to alert the user to The presence of important operating and maintenance servicing instructions in the literature accompanvina the appliance Important Safety Instructions BRead Instructions Read all of the safety and operation instructions before using the product E Retain Instructions Save these instructions for future reference E Attachments Accessories Do not use attachments or accessories unless recommended by the appliance manufacturer as they may cause hazards damage product and void warranty B Installation Do not place or mount this product in or on an unstable or improperly supported location Improperly installed product may fall causing serious injury to a child or adult and damage to the product Use only with a mounting device recommended by the manufacturer or sold with the product To insure proper mounting follow the manufacturer s instructions and use only mounting accessories recommended by manufacturer EPower source This product shoul
Download Pdf Manuals
Related Search