WSC15 USER MANUAL 1. Functions and
Contents
1. Wind Solar Hybrid light controller WSC15 USER MANUAL Thank you for purchasing our Wind Solar Hybrid light controller Please read these instructions before using and keep for future reference Our controllers are designated according to the following convention Please give clear indication before placing orders so that we can provide you products promptly and accurately WSC 15 15 maximum current A 15 15A WSC Wind Solar Hybrid light controller 1 Functions and Features Wind Solar Hybrid light controller is controlled by micro CPU it is an intelligent controller and in possession of Wind amp Solar energy control it is integrated with solar and wind control it can implement Breeze wind generation by exerting pressure on wind turbine Intelligent control of the generator brakes and unloading so that it can protect the generator and equipment safety When the wind is weak and the wind turbine output is insufficient to charge the battery it will start the boost circuit automatically When the wind is too strong it will start the unloading protection circuit automatically Wind Solar Hybrid light controller has the SOC state of charge battery system control function It can intelligently sense the outside light It turns on lights at dark and turns off lights at dawn or the fixed time This controller also intelligently monitors battery charging and discharging It will protect batteries by turning off lights automatica2. lly when the battery voltage is low The controllers will automatically turn to float charge stage when battery is full the batteries by pulse width modulation PWM automatically as the batteries approach full charge It will stop charging to protect batteries from discharging through solar panel at dark The controller also has a protection circuit to prevent accidental damage The environmental defense grade is P22 2 Connection fueyeg peol BUIQUN pup S EUEg JEIOS Please connect the terminal of A B C separately Connection must be according to the figure Before connection please Check the negative and 9 eo positive terminal to avoid failure Waiting for 3 minutes after the connection to make sure the solar controller has finished the program entry before operation Notice The controller must be connected to linear loads such as LED lamps light bulbs etc Please reference the below technical parameter to choose the right wire size according to the current The terminal must be against oxidation and mould to make sure the connection is in good condition Please make necessary protection from the water wet insect for this solar controller when use it open air To make sure the wire connection inside is in good condition Don tuse power from the illumination of light for the solar panel The power of the light is too low to charge the battery Don t use other DC so
3. lors battery power indicator light is orange and the LOAD LED light is green But the load stops working Reason Overload or short circuit happens the fuse inside disconnected automatically solution eliminate the reason of the overload or short circuit load for 10 20 minutes the insurance can be automatically restored when press the Reset reset button the load will return to work
4. on e The controller hastwo buttons Set and Resct the Set button is used to query and set the operating mode Click and then release less than 2 seconds the query operation press and hold the set operation Press the Set button on the controller until the set time or set to release the light control then complete the set e Resct for repairs or street light does not start until use 5 Check and Setup Inquiry Press the SET button while observing the LOAD indicator The controller is in light adjusting condition when the light illuminates fast for 2 seconds The light flashes slowly one time the controller will turn on the load for 30 minutes two flashes for 60 minutes and so on up to 20 flashes for a maximum of 10 hours Setup Our controller is in the default light adjusting mode no time setting before sending to you Press the SET button for a few seconds until the LOAD light illuminates Pressing the SET button will increase the number of flashes which correspond to 30 minute increments of the lights being on each night The light flashes slowly one time the controller will turn on the load for 30 minutes two flashes for 60 minutes and so on up to 20 flashes for a maximum of 10 hours If you want to change the time control light control into the default light control mode just disconnect the solar controller solar panel and battery after a few seconds the solar controller will recover to the default light control mode automa
5. tically 6 Time fixed mode time control light control The time that the light load is switched on can be adjusted between 0 5 and 10 hours The load will be switched on at dark and turn off according to the fixed time 7 Model and Specifications model WSC15 10A WSC15 15A parameter System voltage 12V 24V automatic sense Max charge current 10A 15A Max discharge current 10A 15A High voltage disconnect HVD 13 7V 14 4V 27 4V 28 8V Low Voltage disconnect LVD 10 5V 11V 21V 22VV Low Voltage restore LVR 11 5V 12V 23V 24V Overpressure of Wind turbine and unloading voltage 222V 44V Maximum wire length 1m Charge loop Voltage drop lt 300mV Maximum wire length 1m discharge loop Voltage drop lt 50mV Light control Light control turn on light control turn off Light control time control Light control turn on light control turn off time setting turn off Time control classification 0 5 hours 0 5 hour per step up to 10 hours Output route Single Ambient temperature 25 C 55 C Quiescent dissipation 24mA 8 Trouble shooting Phenomenon Green light goes out the red indicator LED light CHARGE light Reason Low voltage of battery Solution A Cut off the load and reconnect the load after the battery recharged B If there is trouble with the battery charging increase solar panel s power or change battery Phenomenon The three co
6. urce instead of the solar panel to charge the battery It will damage the solar controller Please ensure the output of wind turbine must be three phase alternating current and in good contact The wind turbine and solar panel can be connected individually or together To make sure that the battery is in good contact When the battery is full and the indicator light is green the controller will stop the wind turbine don t rotate the wind turbine compulsively at this time When the wind speed is too large the controller will brake automatically to reduce the speed of the wind turbine 3 Indicator Light The controller has a red charging indicator LED light CHARGE a a green load indicator LED light LOAD a Battery Energy indicator LED light be the first from the left The red indicator LED light CHARGE will light when the batteries are being charged through the solar panel and the green light will be out When the red light is out and green light is light the street lamp will work The green light also helps with search and setup Battery Energy indicator LED light be the first from the left will be red if the battery voltage is low orange during normal working range and green for a fully charged battery working voltage range of the colour changing lamp reference colour changing 12V 24V lamp Red light 10 5V 11V 21V 22V Orange light 10 5 11V 13 7V 21 22V 27 4V Green light 213 7V Z2ITAV 4 Butt
Download Pdf Manuals
Related Search