VM191 user manual
Contents
1. HOW TO SETUP YOUR REMOTE CONTROL Your VM191 remote can control a wide range of Velleman devices At the factory it has been set up to control the K8095 VM8095 MP3 player If you want to control these devices you can skip the setup procedure For all other supported devices please follow the proce dures below Setup procedure In order to be able to use the VM191 remote control with your device the remote and or your device must be configured in the correct way First remove the 3 screws at the back of the remote and open the unit Next select your device from the list below and follow the appropriate setup procedure Note The devices listed below are supported at time of printing Please check www velleman be for an up to date list as devices might have been added 00060 1 2 3 4 USE For use with K8095 VM8095 MP3 player e Press and hold Mode button e Press and hold button 1 until the led flashes e Release both buttons e Close the remote by means of the 3 screws e You device is ready to be used For use with the K8050 VM122 15 channel IR receiver Turn on your K8050 VM122 unit Press and hold Mode button Press and hold button 4 The led will flash briefly every 3s Watch the K8050 VM122 channel leds closely As soon as the channel led of the channel you wish to control with button 1 lights release both buttons The 3 following channels are controlled with button 2 3 a2. ime it flashes a different code is generated You can release both buttons at anytime e Now you can learn the generated code to the MK161 please check MK161 manual for how to instructions e Close the remote by means of the 3 screws e You device is ready to be used 4 For use with the VM192 RGB controller with IR receiver USE e Press and hold Mode button e Press and hold button 4 until the led flashes e Release both buttons e Close the remote by means of the 3 screws e You device is ready to be used Table below indicates button assignment for the different applications Application button1 button2 button3 button4 K8095 VM8095 vol up vol down next previous K8050 VM122 CH x CH x 1 CH x 2 CH x 3 MK161 CH1 CH2 VM192 not available at time of printing Please check www velleman be
3. nd 4 This procedure can take a couple of minutes depending on the address setting of the K8050 VM122 Close the remote by means of the 3 screws You device is ready to be used For use with the MK161 e Press and hold Mode button e Press and hold button 4 The led will flash briefly every 3s Everytime it flashes a different code is generated You can release both buttons at anytime e Now you can learn the generated code to the MK161 please check MK161 manual for how to instructions e Close the remote by means of the 3 screws e You device is ready to be used For use with the VM192 RGB controller with IR receiver e Press and hold Mode button e Press and hold button 4 until the led flashes e Release both buttons e Close the remote by means of the 3 screws e You device is ready to be used Table below indicates button assignment for the different applications Application button1 button2 button3 button4 K8095 VM8095 vol up vol down next previous K8050 VM122 CH x CH x 1 CH x 2 CH x 3 MK161 CH1 CH2 VM192 not available at time of printing Please check www velleman be HOW TO SETUP YOUR REMOTE CONTROL Your VM191 remote can control a wide range of Velleman devices At the factory it has been set up to control the K8095 VM8095 MP3 player If you want to control these devices you can skip the setup procedure For all other supported devices please follow the p
4. roce dures below Setup procedure In order to be able to use the VM191 remote control with your device the remote and or your device must be configured in the correct way First remove the 3 screws at the back of the remote and open the unit Next select your device from the list below and follow the appropriate setup procedure Note The devices listed below are supported at time of printing Please check www velleman be for an up to date list as devices might have been added 00060 1 For use with K8095 VM8095 MP3 player e Press and hold Mode button e Press and hold button 1 until the led flashes e Release both buttons e Close the remote by means of the 3 screws e You device is ready to be used 2 For use with the K8050 VM122 15 channel IR receiver Turn on your K8050 VM122 unit Press and hold Mode button Press and hold button 4 The led will flash briefly every 3s Watch the K8050 VM122 channel leds closely As soon as the channel led of the channel you wish to control with button 1 lights release both buttons The 3 following channels are controlled with button 2 3 and 4 This procedure can take a couple of minutes depending on the address setting of the K8050 VM122 Close the remote by means of the 3 screws You device is ready to be used 3 For use with the MK161 e Press and hold Mode button e Press and hold button 4 The led will flash briefly every 3s Everyt
Download Pdf Manuals
Related Search