DKVM-1708/1716 - PLANET Technology Corporation.
Contents
1. PLANET Networking amp Communication 17 LCD Drawer KVM Console with 8 16 Port Combo Free Module DKVM 1708 1716 K all Wwww PLANET com tw PLANET Networking amp Communication User s Manual of DKVM 1708 1716 Py Copyright Copyright C 2013 PLANET Technology Corp All rights reserved The products and programs described in this User s Manual are licensed products of PLANET Technology This User s Manual contains proprietary information protected by copyright and this User s Manual and all accompanying hardware software and documentation are copyrighted No part of this User s Manual may be copied photocopied reproduced translated or reduced to any electronic medium or machine readable form by any means by electronic or mechanical Including photocopying recording or information storage and retrieval systems for any purpose other than the purchaser s personal use and without the prior express written permission of PLANET Technology Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in t2. g g o 44 Extra rack mounted Screws X8 PLANET Networking amp Communication User s Manual of DKVM 1708 1716 2 3 LCD Components w f z PLANET Networking amp Communication User s Manual of DKVM 1708 1716 2 4 Connecting the Console To connect an LCD console to a computer perform the following steps xp A Jb E 8 Port of KVM 16 Port of KVM 1 Turn off your computer You should always turn off your computer before connecting or disconnecting a device 2 Connect the video VGA connector of the KVM cable to the video card connector on the rear panel of your computer 3 Identify and connect the PS 2 mouse and PS 2 keyboard connector to the correct PS 2 ports on the rear panel of your computer Or you can use USB interface to connect your computer Use PS 2 USB switch to select your interface The switch has to be on PS 2 side when you use PS 2 interface connector 10 PLANET Networking amp Communication User s Manual of DKVM 1708 1716 3 OSD Operation 3 1 Panel Controls and LCD OSD Function Controls Description on Meru To access the main menu This button also acts as the Enter button oes valid factory preset timings AUP _ Press to scroll the function you want to adjust _YDOWN Press to scroll the function you want to adjust Table 3 1 Panel Controls DOWN UP AUTO MENU ON OFF LCD PWR ORO OR ORO Figure 3 1 OSD Con
3. 2 on the panel to enter the OSD If you have modified the Hot Key for starting the OSD and are unable to enter the OSD by pressing NumLock then you can start the OSD by using the Port Selection Switch first and then press F9 to enter into the System Setting to modify the options of the OSD Entry Hot Key If you have modified the Hot Key for starting the OSD and are unable to enter the OSD by pressing NumLock then you can start the OSD by using Port Selection Switch first and then press F9 to enter into the System Setting to modify the options of the OSD Entry Hot Key Operation You can operate the options by keyboard or mouse For the keyboard operation besides the common Up and Down keys there are special function keys such as Enter Space Bar Function Key F1 F4 under the OSD remark field For the mouse operation the left key refers to Enter and the right key refers to Exit For example move the mouse point to your desired PC and click the left key The selection bar will move to that position and then click the left key again for the execution eos You must use the keyboard to complete the two functions Name Edit and Password 14 M PLANET Networking amp Communication User s Manual of DKVM 1708 1716 Switch Menu Master List 03 04 Mail Ser 4 9 LIST MASTER KVM NAME SVS A Mail Group Press Enter Peter Web Group Data Group 1 Move Space Edit Esc Exit F1 Smart View Ent
4. there is a number in this field it shows that a set of KVM connects to this port The number 04 indicates Port 4 and 08 indicates Port 8 and 16 indicates Port 16 and so on M _ POCO e eee OOOOH OHHHHHHHHHHOHOHHHHHHHHHHHOHHHHHOHHOHHHHHOHHHHHHHOHHHHHOHHOHHEHCHOSHHHHHHHHOHHOHHHOHHOHOHHHHHHOHHHOHHOHOHHOHOHOH OOOO EELE VA If the connected KVM is not on there will have no number in this field Note NAME It shows the name of the equipment and users can name the Slave KVM or PC on their own There are a total of 12 characters selected from the group of A Z a Z O 9 mp oc 7 a ae i 13 7 f 13 g f ce A p ce SVS It shows the Smart View Setting use to open and to close The SVS is blank and not clickable if the KVM is connected in parallel If this option is set to open then you can make the switch by operating the Hot Key Switch or Mouse Clicking or selecting the option by Auto Scan You also can use mouse to click this field Selection BAR It shows the selection bar Green you can use the f keys on 16 PLANET Networking amp Communication User s Manual of DKVM 1708 1716 the board to move the selection bar and the situated position indicates the selected target for giving instructions For example if the selection bar points at C 05 and you press Enter then the system will switch to that particular PC or press the Space BAR to start editing the name Press F4 to enable
5. ackets are for 500 800 mm distance means front bracket to rear bracket cabinet contact your dealer if you need longer rear brackets 4 If your cabinet depth is above 800 to 1000 mm please contact your dealer for the stretch rails and replace it for your demand 5 Reliable accessories of rack mounted equipment should be maintained Particular attention should be given to supply connections other than direct connections to the branch circuit 6 The KVM and console are a little bit heavy please prevent these devices from falling down during the installation That may make some people hurt and the console damage PLANET Networking amp Communication User s Manual of DKVM 1708 1716 2 2 Hardware Kits Contents 1 Adjust rail with pull or push to fit your cabinet 2 3 Repeat step 1 2 for the other side 4 Pull the console until rails automatically are locked When users hardly push the console and it can be unlocked by the power is over 4kg 5 Pull and turn the lock knobs left and right at the same time then users can open console to operate PLANET User s Manual of DKVM 1708 1716 Networking amp Communication 6 Put the KVM module into the console form the back There are two ways to install the KVM module in suitable position users can fix KVM module with the KVM accessories Both sides or the extra Rack mounted Screws Bothsides KVM accessories L amp R X2 0
6. disable the SVS option 4 Instruction Hint Field d PT Move SPACE Edit ESC Exit F4 Auto Scan F9 System Setting F5 Clear Name List F1 Smart View Use the keys on the keyboard or the mouse to move the selection bar The Space BAR on the keyboard is used to start editing the name of the PC or KVM Use the Esc key on the keyboard to exit the current option or exit OSD Use the F4 key to run Auto Scan and you can set the residing time channel display time and mode of the Auto Scan from System Setting Use the F9 key to enter into the System Setting Menu Use the F5 key to clear the values of all Name fields If you clear the name list under the Master screen then you will also clear the name lists under all slaves If you clear the name list under a certain slave then you only clear the name list under that particular Slave KVM It switches the Smart View Setting 17 PLANET Networking amp Communication User s Manual of DKVM 1708 1716 e System Setting Menu System Setting Channel Display Fa Mode Channel Display Tim 0 5See Auto Scan Time 5See OSD Entry Hot Key Hot Key Switching Mouse Clicking Beeper Sound OSD Language Security Level Console Lock Time F4 OSDPosttion FS Restore Default Setting Description Default Other Selection For Port Switching Auto Scan Channel Display and OSD Close the Monitor will Number u Mode show
7. e KVM switch modules are loaded with rich features such as one local console port Daisy chain capability On Screen Display OSD menu Password security Searching PC server name Hot key control Push button and Auto Scan control complete keyboard and mouse emulation for simultaneously PC boot up processes 1 1 Packing List The complete package consists of m One 1 8m KVM cable HDB 15 VGA PS 2 x 2 One 1 8m power cord One user s manual CD One quick installation guide Two Rack mount bracket kit One Rack Mount Screw pack Check to make sure that the unit was not damaged in shipping If you encounter a problem contact your dealer Please read this manual thoroughly and follow the installation and operation procedures carefully to prevent any damage to the product and or any of the devices that connect to it PLANET Networking amp Communication User s Manual of DKVM 1708 1716 4 1 2 Product Feature gt Hardware E Heavy Duty Electroplate Steel E Supports high resolution up to 1280 x 1024 75Hz E Complies with EIA RS 310C 19 Rack Mount standard gt System E Supports Combo KVM module to connect servers KVM via USB amp PS 2 connection E Fully supports Logitech Microsoft IBM PS 2 mouse trackball and compatible PS 2 mouse trackball E Supports hot plug not necessary to turn off the original system regardless of a newly installed PC or KVM gt Installation Single
8. e and current rating of the cord should be greater than the voltage and the current rating marked on the product All cautions and warning on the equipment should be noted If the equipment is not in use for long time disconnect the equipment from mains to avoid being damaged by transient over voltage Never pour any liquid into ventilation openings this could cause fire or electrical shock Never open the equipment For safety reason qualified service personnel should only open the equipment If one of the following situations arises get the equipment checked by service personnel The Power Cord or plug is damaged Liquid has penetrated into the equipment The equipment has been exposed to moisture The equipment has not worked well or you can not get it work according to User s Manual The equipment has dropped and damaged If the equipment has obvious signs or breakage MI a PLANET Networking amp Communication User s Manual of DKVM 1708 1716 Index of Contents Sally MNS MUCTONG exssscssd aseesvedasvnnves ENEE E adds EE A EE ESE E MI kider ore on e ea E E E E seceseaadacecaanaccios IV l General Information sasinen ainainen EEEE EA ANATA aiaE l LAPa E E eee E E E E E A E A EE E Te l 2 Prodor Featii Curiei rare T A E ENA AEA EONA ONEEN AAEE EEEE AEAEE 2 Me OU Mee PEA A E TE E A A A T AE A T T ATE ET 2 Zin A AON e E E E N 6 Deel BETT T a a A A E E T T E NT 6 2 2 Hardware Kits Conie IES assscuseanocetn
9. election Note switch 3 For Auto Scan Mode none of the Port Selection Switches functions 3 2 2 Hot Key and Mouse Clicking Hot key and mouse clicking are applicable for switching a small section You can select the SVS Smart View Setting from the OSD of the PC first for a quick switch of PC and use the keyboard press the Ctrl key twice or the mouse press and hold the middle button while pressing the left or right button to switch to the previous or next set of PC 3 2 3 OSD On Screen Display The mouse must have at least 3 keys As far as you select a PC with the SVS you can use this method for the switch Press the NumLock on the keyboard twice or simultaneously press the Push Buttons 1 and 2 of the Port Selection Switch on the KVM panel to start the OSD Use the key Up Down and Enter keys on the keyboard to switch or directly move the mouse to the target PC and then double click the left button Additionally you also can use the numeric keys to enter the direct switch For example if you want to switch a PC to the Slave KVM port 04 under the Master KVM port 03 then you can start the OSD and then directly enter 0304 If you are using a standalone machine then just enter the first two digits More OSD related information is given in the following OSD sections 13 PLANET Networking amp Communication User s Manual of DKVM 1708 1716 Start Press the NumLock twice or the Port Selection Switches 1 and
10. er Switching F4 Auto Scan F9 System Setting F5 Clear Name List Slave List 3 04 Mail Ser 4 LIST Mail Group PWR C KVM p a Mail Ser 2 Mail Ser 3 Mail Ser 4 1 Move Space Edit Esc Exit F1 Smart View Enter Switching F4 Auto Scan F9 System Setting F5 Clear Name List 1 gt This field provides the information of the currently connected PC As shown in the figure above 03 refer to the Port Number of the Master 04 refer the Port Number of the Slave and Mail Ser 4 is the name of this PC defined by Users If 15 PLANET Networking amp Communication User s Manual of DKVM 1708 1716 a PC connects to the Master then the number consists of the first two digits If a User has not given a name for the PC the name field will be blank 2 This field shows the list of the Master KVM or a certain set of Slave KVM currently displayed on the OSD We recommend you to give a name to the Slave KVM or else the display after LIST will be blank 3 This field shows the list of connections to the KVM and the fields are described below PWR It shows the status of power supply and indicates a normal power supply for the equipment PC or KVM connected to the CPU port C It shows the channel number the DKVM 1708 will display 01 08 and the DKVM 1716 will display 01 08 09 16 Since the screen cannot display all at a time therefore you can use PgUp PgDn to switch the pages KVM It shows the KVM model If
11. his User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET assumes no responsibility for any inaccuracies that may be contained in this User s Manual PLANET makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that is incorrect misleading or incomplete we would appreciate your comments and suggestions FCC This device has been tested and found to comply with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received Including interference that may cause undesired operation CE This equipment is in compliance with the requirements of the following regulations EN 55 022 CLASS A WEEE regulation To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment end users of electrical and electronic equipment should understand the meaning of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal m waste and have to collect such WEEE separately Trademarks The PLANET logo is a trademark of PLANET Technology Th
12. inches 2CCFL LCD Panel Maximum Resolution up to 1280 x 1024 SXGA Supports 0 264 H x0 264 V 0 294 H x0 294 V Windows 98SE ME 2000 XP 2003 Vista 7 Server Linux Mac OS9 OSX and Sun Microsystems Support PS 2 and Combo Free KVM module KVM Cable Combo Free x 1 105 key PS 2 keyboard with touch pad 100 240V AC input 1000 points inch 40 points mm graphics tablet mode Display Size Panel Type Resolution Capabilities Pixel Pitch Operating System Multi Platform System Cables Keyboard Mouse Power Source Touch pad U O 5 U Mouse resolution AAE a O 01 3 ad Video 8 HDB 15 female Video 16 HDB 15 female Connectors KB MS PS 2 amp USB signal combined Temperature Operate 5 40 Degree C 41 104 Degree F Storage 20 60 Degree C 4 140 Degree F Humidity 0 80 RH Heavy duty steel materials Chassis Construction Multi Language keyboard support English Germany French Keyboard Language l l l l ltalian Spanish Chinese Default English Certification CEFO PLANET Networking amp Communication User s Manual of DKVM 1708 1716 2 Installation 2 1 Before Installation 1 Please check all peripherals according the list before installation To make sure of the whole unit was not damaged and lost during shipping process If you encountered any problem please contact your dealer 2 Before installation make sure all peripherals and computer have been turned off 3 The standard br
13. is documentation may refer to numerous hardware and software products by their trade names In most if not all cases these designations are claimed as trademarks or registered trademarks by their respective companies Revision User s Manual for Drawer KVM Console with 8 16 Ports Combo Free Module Model DKVM 1708 1716 Rev 2 0 January 2013 Part No EM DKVM 1708 1716_v2 0 II PLANET Networking amp Communication User s Manual of DKVM 1708 1716 Safety Instructions 10 11 12 13 Please disconnect this equipment from AC outlet before cleaning Don t use liquid or sprayed detergent for cleaning Use moisture sheet or clothe for cleaning For pluggable equipment the socked outlet shall be installed near the equipment and shall be easily accessible Please keep this equipment from humidity Lay this equipment on a reliable surface when install A drop or fall could cause injury Do not leave this equipment in an environment unconditioned storage temperature above 60 C it may damage the equipment The opening on the enclosure is for air convection hence the equipment from overheating DO NOT COVER THE OPENING Make sure the voltage of the power source connect the equipment to the power outlet Please keep the power cord such a way that people can not step on it Do not place anything over power cord The power cord must rate for the voltage and current marked on the product s electrical ratings label The voltag
14. osocaseneennadvaddnasenoeyendeosivasenceuuesdeasanetmboedoodavassnaassaednoddeasasdeuseaueaaees 7 2 LL DCOP ON CIS ar saaces soteodba da suedcamoeaoaa ane enasoageaadta Abcmmsccuioanna eseestescnGas 9 2 4 Connecting the CONSOLE ics ui cas sadosieansnanediecadancowerenadatantwedavesanehdoustuusouevwvnlsnnslwsdonensmaddeeadedaebsacedeenrtaies 10 EO DE 20 i E en re PORT mre nn ne een Rene E E ee eer een ee re A eer eer te 1 3 1 Panel Controls and LCD OSD Function eeeesseeeeeeeeeeeeeeesesesnsseseneesseeeseeaaaaeaaaaeaaaaaaaaggs 1 De Be OS PUG eere era EAN EAE EEO EEE 13 Co Mantal Koy serren a E EAE E Gi 13 322 HOt Key and Mouse Clickin pesei e E EE 13 3 2 59 OSD On Sereen DISPlAy porsies aaea Eae a E A ETA Uer EEE 13 IV PLANET Networking amp Communication User s Manual of DKVM 1708 1716 1 General Information The PLANET DKVM 1708 DKVM 1716 is the drawer KVM with single rail console design offering industrial level input solution which optimizes your space utilization by controlling your systems in just 1U space on the rack The separate rail design helps users install the KVM console more easily You don t have to prop the heavy console during the installation but just lock the rails into the rack and then pull the KVM console into the rails Simply use the supplied Combo VGA cable set to link the ports to the console ports of your KVM switch no matter whether your connected port interface be either USB or PS 2 Th
15. rail design easy to install OSD function for LCD display and KVM Switch Cascade controls 128 sets of PCs Supports 6 keyboard languages continually increase 1 3 Features Easy to install With the unique separate rail design One man can install the KVM console easily In case you need to maintain the console you can easily uninstall without effecting the server above or below J0 Jo C o o o j PLANET User s Manual of DKVM 1708 1716 Networking amp Communication Modular KVM switches The user can use DKVM 1708 1716 as single port console or through some simple action and few screws to be 8 16 ports KVM switch Vain Linux Mac Sun Sun 3 PLANET Networking amp Communication User s Manual of DKVM 1708 1716 a Various keyboard language support DKVM 1708 1716 provides multi Language keyboard support English Germany French Italian Spanish Chinese Powerful Mouse Keyboard Support In the present computer applications a mouse has become an indispensable device The KVM fully supports various models of PS 2 mice manufactured by Logitech Microsoft and IBM as well as compatible PS 2 mice of other brands The KVM supports the PS 2 Keyboard Port of the CODE SET1 2 3 and further allows you to use the KVM for all kinds of servers PCs or their combination PLANET Networking amp Communication User s Manual of DKVM 1708 1716 1 4 Product Specification Model Name DKVM 1708 DKVM 1716 17
16. rity mode you need to enter the correct password before you can move the mouse or enter any key from the keyboard You need a correct password to operate the whole system normally Important Note What should I do if forgot my Password After you enter a wrong password for 5 consecutive times a time delay bar will appear and a set of Magic Numbers will show up at the bottom Record the magic numbers and contact with your distributor Console Reconfirmed Simultaneously press the largest two numbered Port Selection Switches on the panel to start the Console Reconfirmed If you change the Console equipment please use this function to let KVM reconfirm the equipment at the Console end once EDID amp DDC A vast majority of computer monitors supports the Extended Display Identification Data EDID and allows data access by Display Data Channel DDC The KVM also supports these two specifications but the KVM only reads the EDID of the Monitor when the KVM is on If it is necessary to change monitors during an operation please use the Console Reconfirmed function to read the EDID again 20
17. t or Right keys on the keyboard or a mouse to move the OSD position F8 Restore Default Setting Restore the factory default settings Please note that all name lists will be cleared and the system settings are set to the default settings as shown in the table above Esc Exit Exit the system setting and close the OSD If you have made changes in this option the system will ask whether or not you want to save the setting before the selected option is effective 19 PLANET Networking amp Communication User s Manual of DKVM 1708 1716 Auto Scan Mode You can start the OSD first and press F4 to enter the Auto scan Mode If you want to scan the PC you must use the Smart View Setting to select the Auto Scan Time in the System Setting for the residing time which includes 5 sec 10 sec 20 sec 30 sec and 60 sec You can adjust the Channel Display Mode and Channel Display Time from the Channel Display mode By then all keys on the panel keyboard and mouse are not operable You can only use the ESC key to exit the Auto Scan Mode Security Mode Switch the Security Level from None to Low in the System Setting and enter your Password A Z O 9 a maximum of 12 characters and the security will be effective after you confirm the Password The use of the Console Lock Time is to set the time to enter a security mode after the keyboard and mouse has idled for a predetermined time Once you enter into the secu
18. the Channel information Name and mode selection Channel Display It shows the time for displaying 5 Sec Time channel information For Auto Scan it shows the Auto Scan Time a residing time for each port OSD Entry Hot Select to turn on the hot keys of riod Scroll Lock Key the OSD control screen Shift None 18 PLANET Networking amp Communication User s Manual of DKVM 1708 1716 Turn on off the Ctrl hot keys on Hot Key a ae the keyboard for switching Switching computer functions Turn on off the keys of the Mouse Clicking mouse for switching computer OFF ON functions Turn on off the beeper sound Beeper Sound ON OFF function Set the offline skip function to Manual Auto auto or manual None 5 Min Fran ais Deutsch OSD Language Select the language for the OSD English Italiano Espa ol l Select the security mode and Security Level level Low High vel 1Min 3Min Console Lock be The lock time of console port 10Min Time 1 30Min 60Min 1 You can select this option only if the Security Level is not None F1 Information It provides the model name and F W version information which is helpful for users to understand the updated version F4 OSD Position you can enter the OSD position to make adjustments we recommend you to unify the resolution for all computer display mode and use this function again to adjust the OSD position You can use the Up Down Lef
19. trol Bar Controls Description Automatically size centers direction and fine tunes Video signal to eliminate noise and direction SHARPNESS Adjusts the clarity and focus of the screen image H POSITION Moves the screen image left or right V POSITION Moves the screen up or down Adjusts image distortion appearing as vertical bars or CLOCK l noise on the screen PHASE Adjusts image distortion appearing as horizontal 1 PLANET Networking amp Communication User s Manual of DKVM 1708 1716 noise on the screen COLOR Adjusts color temperatures for users METER Allows you to choose from among five languages as LANGUAGE English French German Italia Simplified Chinese Espanola and Nederland SPEAKER Volume control Adjust operation of up down on the screen V POSITION OSD OSD Adjust operation of right left on the screen H POSITION Analog Digital signal choice 12 PLANET Networking amp Communication User s Manual of DKVM 1708 1716 3 2 KVM OSD Function 3 2 1 Manual Key It is the simplest switching method You just need to press the Port Selection Switch on the front panel of the KVM The Selection LED Red is on indicating that you are switching to the corresponding port 1 The Port Selection Switch functions only when connected to a PC 2 If the Offline Skip of the OSD System Setting is Auto then you can not make any switch when pressing an offline Port S
Download Pdf Manuals
Related Search