RFID Reader - Samsung CCTV
Contents
1. SAMSUNG TECHWIN RFID Reader User Manual SSA R2000V RFID Reader User Manual Copyright 2010 Samsung Techwin Co Ltd All rights reserved Trademark SAMSUNG Techwin ZHI is the registered logo of Samsung Techwin Co Ltd The name of this product is the registered trademark of Samsung Techwin Co Ltd Other trademarks mentioned in this manual are the registered trademark of their respective company Restriction Samsung Techwin Co Ltd shall reserve the copyright of this document Under no circumstances this docu ment shall be reproduced distributed or changed partially or wholly without formal authorization of Samsung Techwin Disclaimer Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document but no formal guarantee shall be provided Use of this document and the subsequent results shall be entirely on the user s own responsibility Samsung Techwin reserves the right to change the contents of this document without prior notice Warranty If the product does not operate properly in normal conditions please let us know Samsung Techwin will resolve the problem for free of charge The warranty period is 3 years However the followings are excluded e If the system behaves abnormally because you run a program irrelevant to the system operation e Deteriorated performance or natural worn out in process of time Sensory phenomenon that does not affect the performan2. It may cause fire 6 Install it in a place with good ventilation 7 Avoid aiming the controller directly towards extremely bright objects such as sun 8 Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus 9 The Mains plug is used as a disconnect device and shall stay readily operable at any time English 3 safety information FCC Statement Caution Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions any cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If t
3. or containers filled with water on top of the controller Doing so may cause personal injury due to fire electric shock or falling objects Do not install the unit in humid dusty or sooty locations Doing so may cause fire or electric shock If any unusual smells or smoke come from the unit stop using the product In such case immediately disconnect the power source and contact the service center Continued use in such a condition may cause fire or electric shock If this product fails to operate normally contact the nearest service center Never disassemble or modify this product in any way SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair 10 When cleaning do not spray water directly onto parts of the product Doing so may cause fire or electric shock CAUTION 1 Do not drop objects on the product or apply strong blows to it Keep away from a location subject to excessive vibration or magnetic interference 2 Do not install in a location subject to high temperature over 50 C low temperature below 30 C or high humidity Doing so may cause fire or electric shock 3 If you want to relocate the already installed product be sure to turn off the power and then move or reinstall it 4 Remove the power plug from the outlet when there is a lighting storm Neglecting to do so may cause fire or damage o the product 5 Keep out of direct sunlight and heat radiation sources
4. Space 0 vb 4 4 L ov eee ON GR al ee eee IR ee ee E Mark 1 IBV t 8 Data Bits gt i 2 Stop Bits Start Bit it Data packet corresponding to ASCII character A Bi Data Type START 0X02H DATA 8 Char END 0x03H LRC START 0X02H DATA 1 8 Char END Ox03H LRC A Check the following settings Baud Rate 9600bps Data Bit 8 Parity Bit None Stop Bit 1 LRC This is the result of XOR operation of each byte from Start to End 14 output format 8 BIT BURST OUTPUT FORMAT 8Bit Burst Output Format Keypads Binary Hexa Keypads Binary Hexa 0 11110000 FO 6 10010110 96 il 11100001 E1 y 1000011 87 2 11010010 D2 8 01111000 78 3 11000011 C3 9 0110100 69 4 10110100 B4 ESC 01011010 5A 5 10100101 A5 ENT 0100101 4B English 15 1VINH04 LNdLNO troubleshooting TROUBLESHOOTING If the product does not function properly please see the below for trouble shooting PROBLEM SOLUTION Check the rated voltage specified in the user manual and the catalog My card is not read properly Ensure that the card must comply with the PSK 125KH2 format provided by Samsung Cards of 13 56MHz format can not be used Contact the card retailer regarding the card format If the problem persists contact the nearest customer service for your assistance When I turn on the product it sounds a be
5. www samsungsecurity com www samsungtechwin com P No Z8100239101A
6. 36 50 Reader Module 1850 Bezel B T 3mm Hex Wrench L 6 00 0 00 830 1830 3130 4930 56 30 Figure 1 Figure 2 English _ 9 NOILLOANNOO TVN431X3 ANY NOLLVTIVLSNI installation and external connection PRECAUTIONS ON INSTALLATION IF INSTALLING ON A METAL WALL If you install the reader on a metal wall the read range may be reduced To avoid this problem it is recommended to insert the spacer between the metal wall and the reader as shown below Reader IF INSTALLING MORE THAN ONE READER SIDE BY SIDE OR FRONT AND BACK If you install more than one reader side by side or front and back the read range may be reduced In this case if you present a card to one reader the other reader may recognize the same card meaning both readers read the same card simultaneously To avoid this problem keep at least 20cm of space between the two readers Minimum samsund Reader 2 Reader 1 lt Front and Back gt 10_ installation and external connection samsung Reader 1 Minimum 20cm Reader 2 lt Side by Side gt EXTERNAL CONNECTION WIRING DIAGRAM SSA R2000V Wiegand Data 0 Out Green Wiegand Data 1 Out White SAMSUNG Tamper Switch Out NC Light yellow RS 2s20n9 Tamper Switch Out COM Pink Purple CONTROLLER Buzze
7. DC 12V Max 230mA Reading Time Card 30ms Input Port 2 ea External LED Control External Buzzer Control Output Port 26bit Wiegand 8bit Burst for PIN Selectable LED Indicator 3 LED Indicators Red Green and Orange Beeper Piezo Buzzer Keypad 12 Key Touch Keypad with Back Lighting Operating Temperature 30 C to 50 C Operating Humidity 10 to 90 Relative Humidity Non Condensing Color Material Silver with Black Polycarbonate amp Aluminum Die casting Dimension W x H x D mm 87 0 x 109 0 x 25 0 Weight 350 10g Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking on the product accessories or literature indicates that the product and its electronic accessories e g charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for EEE details of where and how they can take these items for environmentally safe recycling Business users should contact their supplier and check the terms and co
8. HINI LONAOHd product Introduction CABLE COLOR SCHEME Item Cable Color Signal Line Description Red DC 412V Power 12V Power Black GND Earth grounding for power Green WIK_DATAO Wiegand Data 0 Output Port White WIK_DATA1 Wiegand Data 1 Output Port Output Purple TX_OUT RS 232 Output Terminal Orange RS 232 GND RS 232 Grounding Terminal Not used Brown NC Not used Yellow Green LED Control N LED Control Input Terminal Input Gray Orange LED Control 2 LED Control Input erminal Blue Buzzer Control BUZZER Control Input Port Pink Tamper COM COM Port of Tamper Switch Tamper Light yellow Tamper NC NC Port of Tamper Switch CABLE SELECTION Item Cable Type 1 Power octay Belden 9409 18 AWG 2 Conductor Unshielded Card PIN data Wiegand Control Signal LED BUZZER TAMPER N Belden 9512 22 AWG 4 Conductor Shielded Belden 9514 22 AWG 8 Conductor Shielded 3 RS 232 Cable Belden 9829 24 AWG 2 twisted pair Shielded 8_ product introduction installation and external connection INSTALLATION 1 See Figure 1 to drill 6 32 holes and 1 2 holes totally 4 into the wall 2 Tighten the four screws to secure the product to the wall 3 With the provided 3mm hex wrench fix the outer case to the product 6 32 hole k 4cm of fi 8 7cm 32 or M3 Screws 1 2 hole i m 6 32 hole 7960 7250 5450
9. ce or quality of the product ex working noise safety Information RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit important operating and maintenance servicing instructions in the literature accompanying the appliance NOILVINYOSANI AL34VS t This exclamation point symbol is intended to alert the user to the presence of WARNING e To reduce the risk of fire or electric shock do not expose this appliance to rain or moisture WARNING 1 a oar ow Be sure to use only the standard adapter that is specified in the specification sheet Using any other adapter could cause fire electrical shock or damage to the product ncorrectly connecting the power supply or replacing battery may cause explosion fire electric shock or damage to he product Do not connect multiple controllers to a single adapter Exceeding the capacity may cause abnormal heat generation or fire Securely plug the power cord into the power receptacle Insecure connection may cause fire When installing the controller fasten it securely and firmly The fall of controller may cause personal injury Do not place conductive objects e g screwdrivers coins metal parts etc
10. ep with dimly turned on indicator Ensure that you are using a larger capacity adaptor than specified in the user manual or the catalog which should cover the rated current consumption of the reader If you are using multiple readers that are connected to one adaptor make sure that the adaptor should be large enough to cover the current consumption multiplied by the reader count Even with a large adaptor enough to supply adequate power if the power cable is not a dedicated line such as communication line or UPT cable or if it s so long to Cause power loss you d better replace it with a dedicated line or reinforce it If the problem persists contact the nearest customer service for your assistance The read range R R of the card differs each time the product reads the card The characteristics of a card are determined by the nature of the coils used and in the manufacturing process engaged by the card manufacturer So what you do first is to check that the cards in use are made by the same manufacturer If you are using cards from different card makers the read range R R differs by the card which is the result of normal operation If you encounter a different read range for each card that is made by the same manufacturer please contact the nearest customer service 16_ troubleshooting product specifications PRODUCT SPECIFICATIONS Item SSA R2000V Power Current
11. his equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help IMPORTANT SAFETY INSTRUCTIONS Read these instructions Keep these instructions Heed all warnings Follow all instructions Donot use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions oo NN DO Ad AOON Do not install near any heat sources such as radiators heat registers or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong is provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs co
12. nditions of the purchase contract This product and its electronic accessories should not be mixed with other commercial wastes for disposal Correct disposal of batteries in this product Applicable in the European Union and other European countries with separate battery return systems This marking on the battery manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life Where marked the chemical symbols Hg Cd or Pb indicate that the battery contains mercury cadmium or lead above the reference levels in EC Directive 2006 66 If batteries are not properly disposed of these substances can cause harm to human health or the environment To protect natural resources and to promote material reuse please separate batteries from other types of waste and recycle them through your local free battery return system English 17 SALES NETWORK SAMSUNG TECHWIN CO LTD Samsungtechwin R amp D Center 701 Sampyeong dong Bundang gu Seongnam si Gyeonggi do Korea 463 400 TEL 82 70 7147 8740 60 FAX 82 31 8018 3745 SAMSUNG TECHWIN AMERICA Inc SAMSUNG TECHWIN EUROPE LTD 1480 Charles Willard St Carson CA 90746 UNITED STATES Samsung House 1000 Hillswood Drive Hillswood Business Tol Free 1 877 213 1222 FAX 1 310 632 2195 Park Chertsey Surrey UNITED KINGDOM KT16 OPS www samsungcctvusa com TEL 44 1932 45 5300 FAX 44 1932 45 5325
13. nt the card to the product until you hear a beep and the green indicator turns on snusune The reader keeps the green indicator turned on while transferring the card data to the controller When it is done the green indicator turns off and for receiving the next card the red indicator stays ON Using the keypad Hold down the keypad until you hear a beep The reader transfers the keypad data to the controller As soon as you press the keypad the orange indicator tums on followed by the reader transferring the keypad data to the controller Then only the red indicator turns on LED Control You can control both green and orange indicators at will To control the green indicator connect the green indicator control line yellow to NO of the controller relay output and connect COM to GND Set I O of the controller now you can control turning on off the indicator You can turn on off the indicators according to the I O settings of the controller which can be applied to various situations For more information about the I O settings of the controller refer to the user manual of the controller To control the orange indicator connect the gray line to NO of the controller Buzzer Control Connect the buzzer control input line blue to the NO port of the controller relay output and GND to the COM port You can configure the I O settings of the controller so that it beeps If the product continues to beep it means that the bu
14. nvenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus e 13 Unplug this apparatus when a card is used Use caution when moving the cart apparatus A combination to avoid injury from tip over 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as powersupply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 4 safety information Contents PRODUCT INTRODUCTION INSTALLATION AND EXTERNAL CONNECTION INITIALIZATION OUTPUT FORMAT TROUBLESHOOTING PRODUCT SPECIFICATIONS mO NO O 10 11 12 13 15 16 17 Features What s included At a Glance Cable Color Scheme Cable Selection SLNALNOO Installation Precautions on installation External Connection Basic Operations Wiegand Output RS 232 Output 8 Bit Burst Output Format Troubleshooting Product Specifications English 5 product Introduction FEATURES This model is an elegant looking proximity reader that is featured by the capacitive touch sensing keypad The back lighted keypad is useful especially for night opera
15. r Control In Blue He RS 232 GND Orange LED Control In Green Yellow LED Control In Orange Gray Ssa naooov Red Black DC 12V GND o Category Cable Wiring Connect the DC 12V to the red line Power Supply Unit Connect GND to the black line Connect the green line of the product to the Wiegand DO input port of the controller Wiegand Connection Connect the white line of the product to the Wiegand D1 input port of the controller Enables you to turn on or off the LED indicators LED Control To control the green indicator connect the yellow line to control the orange indicator connect the blue line with white stripes to the output port of the controller see page 12 zer Enables you to turn on or off the buzzer To control the buzzer connect the blue line to the controller s output relay see page 12 Connect the COM port Pink line of the product s tamper switch to GND connect the NC port Light yellow Tamper Control a of the tamper switch to the input port of the controller RS 232 Connection Connect to the COM port of the PC Connect pin 2 of the DB 9 connector to the purple line connect the orange line to pin 5 of the DB 9 connector English 11 NOILIINNO0 TVNH31X3 ANY NOLLVTIVLSNI intalization BASIC OPERATIONS Initial State when the power is supplied When you apply power to the product it will sound beep three times before entering Standby with the red indicator turned on Using the card Prese
16. tion and its epoxy adhesion and aluminium case relieve you of worries about the rain or any other challenging weather conditions This model permits user access through authentication of the presented proximity card and personal identification number using the keypad With its red green and orange indicators as well as the Piezo buzzer this model is guaranteed to make a stable and correct operation 125 KHz Proximity PIN Reader PSK Modulation 26 bit Wiegand RS 232 Data Output 8 Bit Burst Output Format supported Numeric Keypad with Backlighting for Night Operation Control of External LED Indicators Control of External Buzzer Tamper Switch Reverse Polarity Protection Weatherproof and Dustproof WHAT S INCLUDED Check if the following items are included in the product package samsung MM 3 5 x 40mm Screws x4 Product 3 5 x 25mm Screws x4 CD Manual 6 x 30mm Plastic Anchor x4 Quick Guide 3mm Hex Wrench x1 6_ product introduction AT A GLANCE Front Rear SAMSUNG DE 1 LED Displays the status of the system operation 2 Keypad Used to enter the ID password 3 Tamper Switch A tamper switch to detect falling from the wall 4 Connection Cable Used to connect to the power source or I O cable 5 Buzzer Piezo buzzer 6 Fixing Hole Fixing hole for wall mounting English 7 NOILONGO
17. zzer control is working properly The controller can use the I O settings to set the buzzer control so that it sounds an additional beep for authorized or unauthorized access upon user authentication Furthermore you can make various modifications according to the different I O settings of the controller For more information about the I O settings of the controller refer to the user manual of the controller Card reading is not available while the buzzer control is sounding the buzzer Tamper Control You can set the signal that you want to output if the device is dismantled forcibly Connect the COM port Pink line of the product s tamper switch to GND connect the NC port Light yellow of the tamper switch to the input port of the controller If the tamper of the reader operates the controller produces an input signal and generates the corresponding output depending on the controller setting 12_ initialization output format WIEGAND OUTPUT Timing Diagram 100us He HE 5V DATA 0 mg 0V 5V DATA 1 a ET ov 1 2 3 n 2 n 1 n n 34or26 LOGIC 0 1 1 1 0 0 Data Type 26 bit e Bit 1 Even Parity bit 2 bit 13 e Bit 2 9 Facility Code 000 255 e Bit 10 25 ID Number 00000 65 535 e Bit 26 Odd Parity bit 14 bit 25 English 13 1VINH04 LNdLNO output format RS 232 OUTPUT Output Waveform LSB MSB 15V 0 t1 0 0 0 0 0 1 0
Download Pdf Manuals
Related Search