G-SAVER II - Globestock
Contents
1. SNOS 01 LOY 5 02. There must always be someone top side to operate the G Saver and retrieve the user in an emergency or after a fall Training is essential for those involved with confined spaces work Figure 6 Confined Space Entry Figure 7 Retrieving a User 10 The G Saver II Retractable Fall Arrest Lifeline amp Retrieval System 7 Retrieving the User After a Fall Once a fall has been arrested the user will remain suspended until rescued to a safe platform or the ground It is important that the rescue procedure is carried out quickly after a fall In order to release the fall arrest brake mechanism the suspended person must be raised allowing the rope to retract a little way into the G Saver II The rope can then extract from the unit allowing the user to be rescued to a safe place The retrieval destination and the manner of retrieval must be determined during a pre use assessment The user must not be left suspended for extended periods of time The G Saver II s retrieval mechanism may be engaged to retrieve the user Instructions to Engage the Retrieval Mechanism are also situated on the rear label Pull out up and hold locking trigger ring Push crank arm into body to engage mechanism Align gears if necessary by slight rotation of Crank Arm 2 Release locking trigger ring Ensure it seats within the slot 3 Attempt to pull crank arm away from the body of the unit to check gearing is locked i
3. fitted to the attachment point of the full body harness The G Saver II should be used with the retrieval mechanism disengaged The lifeline is spring tensioned so that it extracts and retracts from the unit ensuring that there is no slack rope Karabiner This enables the user to move freely while helping to keep the potential fall distance to a minimum In the event of a fall rope is pulled out of the unit at an accelerating rate On reaching the activation speed of approximately 1 5m s the braking mechanism will engage The energy of the fall is dissipated and the user brought to a halt There must be adequate clearance below the user to safely stop a fall See sections 6 to 6 2 Once a fall has been arrested the user remains suspended until rescued to a safe platform or the ground The crank arm can be engaged to raise or lower a person To lower a person after a fall the crank arm must first be Raised half a turn to release the fall arrest brake Once the brake is released the operator may lower or raise to retrieve the user The G Saver II Retractable Fall Arrest Lifeline amp Retrieval System 3 Before Use Checks Inspection Inspect the fall arrest system for any signs of damage wear or malfunction The rope should be extracted from and allowed to retract back into the fall arrest unit as it is being inspected The rope should freely return into the unit with no obstructions such as kinks excessive bui
4. ERE IT SHOULD BE USED WITH A PREDETERMINED ACTION PLAN FOR BOTH THE USE AND RECOVERY SHOULD A FALL OCCUR These products have been produced to reduce the risk of injury or death occurring as a result of a fall INCORRECT USE could lead to SERIOUS or FATAL INJURY Only one person should be attached to the G Saver II The equipment user should never be left to work on their own There must always be another person present to initiate the chosen method of retrieving the user should a fall occur The safe use and method of retrieving the user after a fall must be determined during Risk Assessment PRIOR TO USE The appropriate Risk Assessments should be carried out considering use and emergency rescue procedure Users should be fully conversant with the operation of the equipment The Before Use Checks should be performed see section 3 and the Front Label The G Saver II Retractable Fall Arrest Lifeline amp Retrieval System 2 G Saver Fall Arrest amp Retrieval Device The G Saver II has a tough aluminium housing Internal components are manufactured from aluminium alloys stainless steel steel bronze and plastics The G Saver II s anchorage shackle must be attached to a suitable anchorage that meets the strength requirements see section 4 1 and positioned so as to minimise the fall distance The G Saver must be used in conjunction with a Full Body Harness The lifelines safety hook must be
5. USER INSTRUCTION MANUAL G SAVER II Retractable Fall Arrest Lifeline amp Retrieval System EN 360 EN 1496 Class B GLOBESTOCK MILE OAK INDUSTRIAL ESTATE MAESBURY ROAD LAN 2208 Sey OSWESTRY SHROPSHIRE SY108GA TEL 01691 654966 FAX 01691 661726 Issue No 006 Date 30 6 2005 EC Type Examination by SGS United Kingdom Ltd Weston Super Mare BS22 6WA United Kingdom Notified Body No 0120 The G Saver II Retractable Fall Arrest Lifeline amp Retrieval System USER INSTRUCTION MANUAL Contents Page 1 Important Notice 1 2 G Saver Fall Arrest amp Retrieval Device 2 3 Before Use Checks 3 4 Installation 4 4 1 Anchorage Points Devices 5 4 2 Connectors 5 4 3 Attaching the User 5 5 Instructions for Use 6 6 Assessing the Working Environment 7 6 1 Fall Arrester Anchored Vertically Overhead 7 6 2 Fall Arrester Anchored Horizontally 8 6 3 G Tripod Anchorage for Confined Space work 10 7 Retrieving the User after a Fall 11 8 Inspection amp Maintenance 12 8 1 Periodic Examination 12 8 2 Service amp Re Certification 12 8 3 Cleaning Storage and Transportation 12 9 Attaching to the G Tripod 13 The G Saver II Retractable Fall Arrest Lifeline amp Retrieval System 1 IMPORTANT NOTICE READ EQUIPMENT LABELS AND USER INSTRUCTION MANUAL BEFORE USE BEFORE USING THIS EQUIPMENT IT IS ESSENTIAL THAT USERS ARE FULLY AWARE OF HOW TO OPERATE THE EQUIPMENT WH
6. aned using warm water with a mild detergent It should then be hung by it anchorage shackle to dry in a warm environment In order to maintain the wire rope extract the rope from the unit removing any soiling Apply a little light oil to a cloth Hold the cloth around the rope allowing the rope to slowly retract back into the unit This will leave the rope lightly oiled while ensuring the internal mechanism is not oil contaminated 12 The G Saver II Retractable Fall Arrest Lifeline amp Retrieval System SH The unit should be stored in a clean dry chemical free environment The unit is best stored off the floor ideally hanging by it s anchorage shackle Transportation During transportation the G Saver II should be boxed or suitably retained so as to prevent damage or deterioration 9 Attaching to the G Tripod The G Saver II fits onto the fixed leg of the Tripod with an upper and lower mounting bracket 1 Assemble the tripod 2 Remove the G Saver II s shackle 3 Fit the upper and lower mounting brackets onto the tripod fixed leg approx 1 2 metre apart 4 Remove the Hand Nut from the lower mounting bracket Fit the G Saver II anchorage hole onto the threaded stud Replace the Hand Nut 5 Lower the upper mounting bracket onto the G Saver II 2132 The G Saver II Retractable Fall Arrest Lifeline amp Retrieval System to secure in place 6 Tighten the Hand Nut 7 Extrac
7. ditional Swing Clearance 6 2 Fall Arrester Anchored Horizontally The fall arrest brake mechanism will operate with the unit mounted in any orientation There must be adequate clearance below the working area to stop a fall safely See figure 3 Clearance To Stop Fall Be aware of working sideways out from the fall arrester Additional clearance is required where there may be a swinging fall 2m Height of User Figure 3 The G Saver II Retractable Fall Arrest Lifeline amp Retrieval System In the event of a fall the rope must not pass over sharp abrasive edges masonry steelwork electrical wires components that may harm the user Anything that may catch trap or shear the wire The User could be in MORTAL DANGER if the above points are ignored The anchorage must be situated so as to minimise the potential fall distance taking special notice of swing falls See figure 4 Should the user fall the brake mechanism will activate at an approximate speed of 1 5 m s If the fall does not reach this speed then the brake may not activate Figure 5 Anchorage to minimise Fall Distance 9 The G Saver II Retractable Fall Arrest Lifeline amp Retrieval System 6 3 G Tripod Anchorage for Confined Space Work The G Saver II may be used with the G Tripod for protection when entering or working in confined spaces See section 9 for set up instructions
8. etermined appropriate by a formal risk assessment Section 6 2 d mounted on a temporary anchorage device such as the G Tripod for protection in confined space applications Section 6 3 amp 9 2m Height of User 2m Height of User Minimum Clearance Minimum Clearance To Stop Fall To Stop Fall The anchorage for the G Saver II should be positioned so as to 1 Minimise the fall distance 2 Avoid any obstacles Fall away from rather than into any obstacles that may harm the user 4 The G Saver II Retractable Fall Arrest Lifeline amp Retrieval System 4 1 4 3 Anchorage Requirements e to EN 795 may be used e Anchor points must have a minimum static strength of 1225kg 12KN per attached G Saver II Connectors e Connectors used with the G Saver II should be to EN 362 or equivalent e Metal connectors must have a minimum strength of 1530kg 15KN in the direction of loading e Webbing products or non metallic connectors must have a minimum strength of 2240kg 22KN These must not be used in contact with sharp edges or rough abrasive surfaces that may cause damage e Lanyards must not be used to extend the length of the wire rope Where deemed suitable by the harness manufacturer a short strap 0 5m maximum length may be fitted to extend the attachment point of the full body harness allowing easier connection of the safety hook Attaching to the User T
9. he User must wear a Full Body Harness that meets the requirements of EN361 Connect the G Saver II s Safety Hook Karabiner directly to the fall arrest attachment point of the Harness Ensure that the gate is closed and locked The G Saver II Retractable Fall Arrest Lifeline amp Retrieval System 5 Instructions for Use Should any doubt arise about the safe condition of this device DO NOT USE Return to manufacturer or a manufacturer authorised servicing agency for attention Protect your hands when inspecting or handling the wire rope A rescue plan must be in place and ready to be implemented should a fall occur Never use as a restraint or positioning device For protecting one user only as a fall arrester when attached to that user s full body harness attachment point Never use the fall arrester for protection on or above unstable materials such as grain mounds powders etc where the user runs the risk of slowly sinking into the material below the fall arrest brake activation speed The retractable fall arrester may only be used by a trained and or otherwise competent person or the user should be under the direct supervision of such a person The Retractable Fall Arrester should only be used or subjected to temperatures within the range of 50 to 30 centigrade Always position the anchorage or choose an anchorage point that minimises the fall distance Ensure there is enough clearance below the work area to safe
10. ied out after reading this manual Each application may be different These instructions are produced as a guide only They can never replace the requirement for a formal assessment of each application by a suitably competent person A plan of work and emergency rescue procedure must be in place The work emergency rescue procedures must be continually considered to suit any changes in the working environment 6 1 Fall Arrester Anchored Vertically Overhead Working with the fall arrester anchored vertically overhead is the ideal arrangement for use as the potential fall distance is kept to a minimum There must always be adequate clearance below the working area to allow a fall to be stopped safely Allow 2 metres plus the Height of the User for clearance below the working area See figure 1 Be aware of any form of obstruction that may injure the user should a fall occur Implement measures to remove any risk The G Saver II Retractable Fall Arrest Lifeline amp Retrieval System Where there is the possibility of a swing fall occurring Additional clearance below is required if working out from underneath the fall arrester See figure 2 Beware of swinging into obstructions for 10m Rope at 30 1 5m Additional Pendulum Swing Allowance Max Working Range of User Clearance 2m Height m Height of User Clearance Figure 1 Pendulum Swing Clearance Below Figure 2 Ad
11. ld up of dirt or other fouling preventing retraction Check the safety hook and it s gate locking function Test Test the Fall Arrest Function With the retrieval arm disengaged test the fall arrest function by pulling sharply on the safety hook The unit s brake must lock positively and remain locked until released Test the Retrieval Mechanism Pull out up and hold locking trigger ring Push crank arm into body to engage mechanism Align gears if 8 Locking necessary by slight rotation of Crank Trigger Arm Release locking trigger ring Ensure it seats within the slot Attempt to pull crank arm away from the body of the unit to check gearing is locked in position 4 Rotate Crank Arm Lift up locking trigger ring pull out Crank Arm and release locking trigger ring to disengage mechanism The G Saver II Retractable Fall Arrest Lifeline amp Retrieval System 4 Installation Connect the G Saver II to an anchor point by it s shackle The fall arrest brake mechanism will activate in any orientation When used lying Crank Arm down some premature activation may occasionally be experienced Following are some examples of installation configurations The G Saver II can be used a mounted vertically overhead b with a diverter pulley to provide safe overhead fall protection and provision for rescue for roofing applications in conjunction with a suitable roof anchor where d
12. ly arrest a fall The user s potential fall path should be free of obstructions that could cause injury or limit the fall to below the fall arrest brake activation speed Does fall protection necessitate the use of further Personal Protective Equipment such as Helmets knee pads gloves etc for that environment When the rope is extended do not release and allow the wire rope to run freely back into the device Never cross another person s lifeline Never allow the rope to pass under or get wrapped around a person their arms or legs When working never allow the rope to become slack never clamp off or stand on the wire rope Do not allow the rope to pass over sharp edges electrical items cables become frayed or to kink as this weakens the rope Be aware of any medical condition that may affect the safety of the equipment user in normal and emergency use If there is any doubt seek medical advice or do not use the equipment The G Saver II Retractable Fall Arrest Lifeline amp Retrieval System 6 Assessing The Working Environment For use in any requirement for working at height that demands mobility over a large working area The fitness for purpose must be verified by formal risk assessments These notes are for guidance purposes only It is essential that a person who is trained or otherwise competent to do so assesses applications An assessment to determine the safe use and emergency retrieval plan should only be carr
13. n position 4 Rotate Crank Arm up half a turn to disengage Fall Arrest brake The User can now be Raised or Lowered to safety The G Saver II Retractable Fall Arrest Lifeline amp Retrieval System Inspection amp Maintenance Like all complex mechanical safety devices the G Saver II requires regular inspection and maintenance to ensure that the unit functions correctly Repairs or servicing should never be carried out on site or in the field Do not tamper with or modify the unit 8 1 Periodic Examination The G Saver should be periodically examined by a competent person other than those using the equipment at least once in every 6 months dependant upon the frequency of use and the operating environment The Examination Record found on the rear of this manual outlines the main examination criteria On passing this examination the record can be completed signed off and the unit returned for use Any observed faults must be rectified If necessary return the G Saver II for service and re certification 8 2 Service amp Re Certification The G Saver must be returned for servicing annually and in the event of a fall arrest Only a Globestock approved servicing agency can be used for this On completion of a service and retest a new Test Certificate will be issued which validates the unit for a further year of use 8 3 Cleaning Storage and Transportation The G Saver II s exterior may be cle
14. t rope and guide through the staggered rope slot above the pulley 8 Feed the rope through the guide slot below the pulley Rotate the Lock Ring to secure the rope 9 Ensure all locking Levers and Hand Nuts are tight and secure The Tripod can now be adjusted to the desired height Staggered Rope Slot spac The G Saver II Retractable Fall Arrest Lifeline amp Retrieval System Notes JJA AAS smod PUOTIPPV OINDIS 29 quosoid S1OU9ISC uonIpuoD 001801100 ON Alojovjsnes aseulep ON 198510 8 NO J20 0 1514 25 NISIA wy uonouny dn 29 UMOP sosesuasiq sosesuq 141897 2 Juasaid 7 29 yuosoid 29 4 UOISOLIOD 2 JO IA UOY JOAIMS quasaid 1 101802109 JO IOI 10 spurns AT NJ SINAI AQLI AT NJ 3 qL Ajdieys u ym 57901 uonouny 15 WA 0 095
Download Pdf Manuals
Related Search