Laser Distance Meter
Contents
1. far as possible 10 Not including Type DM1 Horizontal measurement Press short button to activate horizontal measurement in the instrument The following symbol appears in the display lt fIf the button is active the horizontal distance is displayed in the summary line for each distance 13 measurement up to max 45 and up to max a transverse tilt of 10 Press the button to collect the measurement data and the data will be on the display And hypotenuse distance and angle will be on the auxiliary display Minimum maximum measurement 14 This function allows the user to measure the minimum or maximum distance from a fixed measuring point It can also be used as to determine spacings It is commonly used to measure room diagonals maximum values or horizontal distances minimum values or the difference of maximum and minimum A Press and hold down this button until you hear a beep Then slowly sweep the laser back and forth up and down over the desired target point e g into the corner of a room Press to stop continuous measurement The values for maximum and minimum distances are shown in the display as well as the last measured value in the summary line l l Functions Addition subtraction Distance measuring The next measurement is added to the previous one ed The next measurement is subtracted from the previous one This process can be repeated as r2. is not in the warranty 28 All illustrations descriptions and technical specifications may be subject to change withoutprior notice The whole of laser distance meter Battery target board hand strap soft package packaging and other auxiliary equipments are not in the free maintenance range NSP pamela ue on die ray cure free maintenance service of this machine will be from the date of manufacture 29
3. 0 press button a until the display shows 0 1 Wait for 5 sends then rotate the instrument by 180 degree Press the button and it shows 0 2 wait till it shows 0 0 for finishing the correction Press the button for exiting Illuminating Display ap button pressed short the illuminating display can be turned on or off 11 Operation Switching on or off a Switches on the instrument and laser The display shows the battery symbol until the next button is pressed Pressing this button for longer switches the instrument off The instrument switches off automatically after 3 minutes of inactivity CLEAR button The last action is canceled While making area or volume measurements each single measurement can be deleted and remeasured in series Reference setting The default reference setting is from the rear of the instrument It will show H on the display a Press long this button to take the next measurement from the front edge The display will show Press this button the rear reference is set again 12 Level Gauge 60m instrument Press for long time to choose the level gauge on or off Measuring Single distance measurement Press to activate the laser a Press again to trigger the distance measurement The result is displayed immediately Tilt measurement The tilt sensor measures tilts between 45 During the measurement of tilt the instrument should be held without transverse tilt as
4. If the measurement is the horizontal distance you can not measure the distance of the picture 2 When measure the distance of picture 1 you need press amp button to switch off the angle sensor then through the three sides to determine the distance If the measurement is the horizontal distance fix the instrument Let the light point direct to point 1 and point 3 read angle values on the 20 secondary line of point 1 and 3 If less than 45 it is only need to measure the point 1 and point 3 then it will be able to confirm the distance Otherwise also need to measure the point 2 to determine the distance For 60m device Then press long this button to turn off the angle sensor Baim at the upper point 1 and trigger the measurement After the first measurement the value is adopted After the measurement if the angle sensor is turned off keep the instrument as horizontal as possible Press and hold down this button to trigger continuous measurement Sweep the laser up and down over the ideal target point 2 Press to stop continuous measurement 2 The value is adopted press this button to trigger the measurement 3 The result is displayed in the summary line the partial results in the secondary lines 21 Storage of constants historical storage Historical storage Press for long time The icon g will show on the display and the previous 10 results measureme
5. Laser Distance Meter Operation Instruction are o ni ser Distance Meter Congratulations on the purchase of our product A Carefully read the Safety Instructions and the User Manual before using this product The person responsible for the instrument must ensure that all users understand these directions and adhere to them Safety Instructions Symbols used ymbols used in the Safety Instructions have the following meanings AWARNING Indicates a potentially hazardous situation or an unintended use which if not avoided will result serious injury ACAUTION Indicates a potentially hazardous situation or an unintended use which if not avoided may result in minor injury and or in appreciable material 1 financial and environmental damage important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner Use of the instrument Permitted use e Measuring distances e Computing functions e g areas and volumes e Indirect measurement Pythagoras proposition Plus or minus measurement Tilt measurement Prohibited use e Using the instrument without instrument e Using outside the stated limits e Deactivation of safety systems and removal of explanatory and hazard labels Opening of the equipment byusing tools screw drivers etc as far as not specifically permitted for certaincases Car
6. cur WARNING Flat batteries must not be disposed of 6 with household waste Care for the environment and take them to the collecting points provided in accordance Sf with national or local regulations Ca The product must not be disposed of with household waste Dispose of the product appropriately in accordance with the national regulations in force in your country Always prevent access to the product by unauthorized personnel Technical Support 11local dealer Electromagnetic Compatibility EMC The term electromagnetic compatibility is taken to mean the capability of the product to function smoothly in an environment where electromagnetic radiation and electrostatic discharges are present and without causing electromagnetic interference to other equipment 7 WARNING The product conforms to the most stringent requirements of the relevant standards and regulations Yet the possibility of it causing interference in other devices cannot be totally excluded CAUTION Never attempt to repair the product yourself In case of damage contact the local dealership Laser classification Integrated distance meter AS The distance meter produces a visible laser beam which emerges from the front of the instrument 8 It is a Class 2 laser product in accordance with IEC60825 1 2007 Radiation safety of laser products Laser Class 2 products Do not stare into the laser beam o
7. ditions Measuring range The range of 40m instrument is limited to 40 m and 60m instrument is limited to 60m At night or dusk and if the target is in shadow the measuring range without target plate is increased Use a target plate to increase the measurement range during daylight or if the target has poor reflection properties 26 Target surfaces Measuring errors can occur when measuring toward colourless liquids e g water or dust free glass styrofoam or similar semi permeable surfaces Aiming at high gloss surfaces may deflect the laser beam and lead to measurement errors Against non reflective and dark surfaces the measuring time may increase Care Do not immerse the instrument in water Wipe off dirt with a damp soft cloth Do not use aggressive cleaning agents or solutions Handle the instrument as a camera or telescope 27 Warranty The instrument comes with one year warranty This effective prerequisite of the warranty is as follows You should operating instructions handling processing cleaning and maintaining this instrument according with our company s use of instrument and maintaining it at good technical condition This means that the tools can only use the original parts and spare parts from our company This warranty only provides free repair or replacement of defective parts in the entire expected lifetime of the tool If the parts need repair or replacement due to normal wear and tear
8. equired the measurement will be displayed in the summary line while the previous one displayed in the secondary line The last step will be reverted This function is also available for area and volume measurement Area Press once The symbol appears in the display Press this button to take the first length measurement e g length Press it again to take the second length measurement e g width The result is displayed in the summary line 16 Volume Press this button twice The g symbol appears in the display Press this button to take the first length measurement e g length Press this button to take the second length measurement e g width Press this button to take the third length measurement e g height The volume then appears in the summary line Tilt measurement Press this button once to activate the tilt sensor The symbol appears in the display The tilt is continuously shown as or setting depending on the press to measure the inclination and the distance Not including Tupe 40m instrument Indirect measurement Pythagoras proposition The instrument can calculate distances using Pythagoras proposition Make sure you adhere to the prescribed sequence of measurement All target points must be in a horizontal or vertical plane The best results are achieved when the instrument is rotated about a fixed point e g with the positioning bracket f
9. he instructions This person is also 4 accountable for the deployment of personnel and for their training and for the safety of the equipment when in use The person in charge of the instrument has the following duties To understand the safety instructions on the product and the instructions in the User Manual To be familiar with local safety regulations relating to accident prevention To inform local dealer immediately if the equipment becomes unsafe Hazards in use measurements if the instrument is defective or if it has been dropped or has been misused or modified Precautions Carry out test measurements periodically Particularly after the instrument has been subject to abnormal use and before during or after important measurements Make sure the optics is kept clean and that there is no mechanical damage to the bumpers CAUTION In using the instrument for distance measurements or for positioning moving objects e g cranes building equipment platforms etc unforeseen events may cause erroneous measurements Precautions Only use this product as a measuring sensor not as a controlling device Your system must be configured and operated CAUTION Watch out for erroneous distance in such a way that in case of an erroneous measurement malfunction of the device or power failure due to installed safety measures e g safety limit switch it is assured that no damage will oc
10. nts or calculated results are shown in reverse order The and f buttons can be used for navigation Appendix Message codes All message codes are displayed with either icon or Error The following errors can be corrected 22 Technical Data ee MT A HN ES ME ES Calculation error Receiving the reflected light too weak or too strong Measurement time too long classification Class 2M II Class 2M II r Reoperation change a better surface reflecting or using target plate The goal of the ambient Change the light for light is too strong measuring Cool down or Warm up ps the instrument External te ne 0c ox Temperature will be selec available from OC to 40 T i Switch on off the instrument several times If the symboal still appears then your instrument may be defective Please call your dealer for assistance Tee reas tos asm Ds Hardware error 23 24 Use a target plate to increase the measurement range during daylight or if the target has poor reflection properties Measurement could reach 10 m in good conditions good measurement surface room temperature Under adverse measuring conditions such as the light is too strong the measured surface reflective weakly or the temperature difference is too large or the deviation over distance above 10m will increase on 0 2 mm m 25 Measuring con
11. r direct it towards other people unnecessarily Eye protection is normally afforded by aversion responses including the blink reflex WARNING Looking directly into the beam with optical lens e g binoculars telescopes can be hazardous Precautions Do not look directly into the beam with optical lens CAUTION Looking into the laser beam may be Inserting replacing batteries 1 Remove battery compartment lid and attach hand strap 2 Insert batteries observing correct 9 polarity 3 Close the battery compartment again Replace the batteries when the symbol flashes permanently in the display Only use alkaline batteries Remove the batteries before any long period of non use to avoid the danger of corrosion Menu functions Setting the unit for distance measurements Press for long time The following units are available m meter ft feet in inch ft in feet inch 1 16 Beep Press ME for long time to choose BEEP s on or off 10 Laser continuous x a Press and hold down the key when switching on the device until the character T appears permanently in the display with beep sounds Every further press of the a key releases a distance measurement amp Press the key and hold to switch the device and Laser continuous operation off The correction of tilt sensor Press long this button you are in the tilt measurement press five times when the bottom of display shows 0
12. rying out modificationor conversion of the product Use after misappropriation e Use of accessories from other manufactures without the express approval Deliber ate orirresponsible beha viouron scaffolding when using ladders when measuring near machines which are running or near parts of machines or installations which are unprotected aiming directly intothe sun Deliberate dazzling of third parties also in the dark Inade quate safe guards at the survey ing site e g when measuring Limits of use See section Technical Date This product is designed for use in areas permanently habitable by humans do not use the product in explosion hazardous areas or in aggressive environments 3 Areas of responsibility Responsibilities of the manufacturer of the original equipment It is responsible for supplying the product including the User Manual and original accessories in a completely safe condition Responsibilities of the manufacturer of non original equipment CS The manufacturers of non original equipment for the product are responsible for developing implementing and communicating safety concepts for their products They are se safetalso responsible for the effectiveness of they concepts in combination with the equipment Responsibilities of the person in charge of the instrument WARNING The person responsible for the instrument must ensure that the equipment is used in accordance with t
13. ully folded out and the instrument placed on a wall Make sure that the first measurement and the distance to be measured are at right angle Use the Minimum maximum function as explained in Measuring gt Minimum maximum measurement Indirect measurement determining a distance using 2 auxiliary measurements e g for measuring building heights It is helpful to use a tripod 18 Press this button once the display shows The laser is switched on Aim at the upper point 1 and trigger the measurement After the first measurement the value is adopted The result is displayed in the summary line the partial results in the secondary line e g Angle and Hypotenuse distance If the angle is above 45 it need to measure point 2 Press to switch off the angle sensor then must measure the distance of point 1 Keep the instrument as horizontal as possible during the measuring Press and hold down this button to trigger continuous measurement sweep the laser back and forth up and down over the ideal target point Press to stop continuous measurement point 2 The result is displayed in the summary line the partial results in the secondary line e g Hypotenuse and right angle edge distance 19 Indirect measurement determining a distance using 3 auxiliary measurements E Press this button twice the display shows the following symbol g The laser is switched on
Download Pdf Manuals
Related Search