BigGreen Commercial™
Contents
1. 3 The top half of the dirty water tank can also be rinsed clean through the nozzle area 4 After carpet is dry vacuum again to remove hair and fuzz Belt removal and replacement 1 Turn off the machine and unplug it from the outlet 2 Remove the dirty and clean water tanks from the base of the machine 3 While standing behind the unit lay the unit on its side cord side up 4 Looking at the bottom of unit find the back center of the brush carriage where the carriage latch is located It is between the brush assembly and the front wheels 5 Pull brush carriage towards you with one hand until it stops then pinch the carriage latch with other hand while pulling the carriage towards you The carriage should swing out to access belt cover 6 Remove three screws from cover Lift and remove to access brush carriage 7 Turn the belt inward towards the large pulley while lifting out 8 Place new belt over small pulley first and 10 then slip the belt over the large pulley Vs p C 9 Replace the brush carriage and screws P 10 Push brush carriage back into place making sure the carriage latch locks back into place Maintenance and care Brush removal and replacement 3 1 Turn OFF 0 the machine and unplug from the outlet 2 Remove the dirty and clean water tanks from the base of the machine 3 While standing behind the unit lay the unit on its side c2. and will void the warranty BISSELL 1X Commercial Cleaning Formula Assembly Your BISSELL Commercial Deep Cleaner BG10 comes with no assembly required 4 Operations Before you clean ud 1 Move furniture to another area if clean ing the entire room optional 2 Vacuum area with a dry vacuum cleaner thoroughly before deep cleaning 3 Plan your cleaning route to leave an exit path It is best to begin cleaning in the corner farthest from your exit Carpet cleaning 1 Remove dirty water tank Pull dirty water tank handle to upright position and lift up to remove dirty water tank 2 lift clean water tank from the base of machine A Unscrew cap on top of the clean water tank Fill tank to FILL line with clean hot tap water B Follow instructions on the label of the Chemical you are going to use in the machine Always use genuine BISSELL formulas to maximize cleaning and for the safety of your machine C Screw cap back onto clean water tank and place tank onto base of the machine on to handle Replace dirty water tank Seley of the clean water tank and pus back to lock into place Plug into a proper outlet and turn the power switch to the ON 1 position Detent handle by pushing down on the green lever on the back of the machine while pulling back Cleaning strokes While pressing the trigger make one slow forward wet pass and another back Let the formula
3. fire e e e electric shock or injury E Do not immerse E Use only on surfaces moistened by cleaning process Wl Always connect to a properly grounded outlet E See Grounding Instructions E Unplug from outlet when not in use and before conducting maintenance or troubleshooting E Do not leave machine when it is plugged in WI Do not service machine when it is plugged in E Do not use with damaged cord or plug Wi f appliance is not working as it should has been dropped damaged left outdoors or dropped into water have it repaired at an authorized Service Center E Use indoors only E Do not pull or carry by cord use cord as a handle close door on cord pull cord around sharp corners or edges run appliance over cord or expose cord fo heated surfaces Wi Unplug by grasping the plug not the cord E Do not handle plug or appliance with wet hands WI Do not put any object into appliance openings use with blocked opening or restrict air flow E Do not expose hair loose clothing fingers or body parts to openings or moving parts E Do not pick up hot or burning objects E Do not pick up flammable or combustible materials lighter fluid gasoline kerosene efc or use in the presence of explosive liquids or vapor E Do not use appliance in an enclosed space filled with vapors given off by oil base paint paint thinner some moth proofing substances flammable dust or other explosive or toxic vapors E Do not pick
4. up toxic material chlorine bleach ammonia drain cleaner gasoline etc E Do not modify the 3 prong grounded plug E Do not allow to be used as a toy E Do not use for any purpose other than described in this User s guide E Do not unplug by pulling on the cord E Use only manufacturer s recommended attachments E Always install float before any wet pick up operation E Use only cleaning products formulated by BISSELL for use in this appliance to prevent internal component damage See the cleaning fluid section of this guide E Keep openings free of dust lint hair etc E Do not point attachment nozzle at people or animals E Keep appliance on a level surface E Do not use without intake screen filter in place E Turn off all controls before unplugging E Unplug before attaching the TurboBrush E Be extra careful when cleaning stairs E Close attention is necessary when used by or near children SAVE THESE INSTRUCTIONS THIS MODEL IS FOR COMMERCIAL USE GROUNDING INSTRUCTIONS This appliance must be connected to a grounded wiring system If it should malfunction or break down grounding rovides a safe path of least resistance jo electrical current reducing the risk of electrical shock The cord for this appli ance has an equipmentgrounding con ductor and a grounding plug It must only be plugged into an outlet that is properly installed and grounded in sekar donee with all local codes a
5. 5 6 6 8 12 SALES SERVICE PARTS CALL 1 877 977 3339 JanitorialEquipmentSupply com Bissell BigGreen Commercial BG10 USER S GUIDE 10N2 SERIES Thank You Safety Instructions Product View Assembly Operations Maintenance and Care Troubleshooting Replacement Parts Accessories Warranty Customer Care Thanks for buying a BISSELL Commercial Deep Cleaner Thanks for buying a BISSELL Commercial Deep Cleaner BG10 We re glad you purchased a BISSELL Commercial Deep Cleaner BG10 Everything we know about floor care went into the design and construction of this complete high tech commercial cleaning system Your BISSELL Commercial Deep Cleaner BG10 is well made and we back it with a limited one year warranty We also stand behind it with a knowledgeable dedicated Customer Care department so should you ever have a problem you ll receive fast considerate assistance My great grandfather invented the floor sweeper in 1876 Today BISSELL is a global leader in the design manufacture and service of high quality commercial products like your Commercial Deep Cleaner BG10 Thanks again from all of us at BISSELL AV ord d AO Mark J Bissell Chairman amp CEO IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance basic precautions should be observed including the following READ ALL INSTRUCTIONS BEFORE USING YOUR COMMERCIAL DEEP CLEANER BG 10 A WARNING To reduce the risk of
6. You may notice hair and debris deposits on the carpet or in the tank that were loosened by the cleaning action especially with newer carpets that have never been deep cleaned before This debris should be picked up and thrown away AN CAUTION Do not overwet Take care not to jects or edges ing brush may 10 Fill the clean water tank with clean hot tap water and follow instructions 2 7 to continue cleaning run over loose o of area rugs Stal result in premature belt failure Maintenance and care Machine storage Once your cleaning is complete make sure both the dirty and clean water tanks are emptied rinsed out and dried before the next use Note Store cleaner in a protected dry area Since this product uses water it SALES SERVICE PARTS must not be stored where there is a CALL 1 877 977 3339 danger of freezing Freezing will dam JanitorialEquipmentSupply com age internal components and void the warranty Maintenance and care Machine care For best results a few simple steps can AN WA R N l N G assure your machine is well maintained To reduce the risk of fire electric after your cleaning is complete shock or injury turn power OFF and disconnect plug from l Turn power OFF 0 Unplug the machine electrical outlet before performing and wrap the power cord maintenance or troubleshooting 2 After emptying the clean and dirty water tanks rinse them out with running hot tap water
7. and DirtLifter PowerBrushes do the work for you Note Your machine is equipped with a circuit breaker that will automatically shut off the brush if a large or loose object is caught in the brush roll If that happens be sure to unplug your machine remove the foreign object and then plug machine in to reset the circuit reaker ATTENTION Some Berber carpets have a tendency to fuzz with wear Repeated strokes in the same area with an ordinary vacuum or deep cleaner may aggra vate this condition Keep plenty of genuine BISSELL 1X oaaae on hand so you can clean whenever it fits your schedule Always use genuine BISSELL deep cleaning formulas Non BISSELL cleaning solutions may harm the machine and vod the warranty Operations Carpet cleaning continued 7 Cleaning strokes Release the trigger and make one slow forward and bore ward pass over the same area to remove any residual dirty water and aid in drying Repeat cleaning passes until solution being pulled up appears clean Continue passes without pressing the trigger until you can t see any more water being pulled up 8 Remove the dirty water tank by pulling the handle to the upright position and lift up Carry the tank like a Bucket to a utility sink or outside where you will dispose of the dirty water 9 Unlatch the top of the tank from the bottom by Ud the handle all the way forward and ifting the top off Pour dirty water into the sink Note
8. arding this warranty or have questions regarding what it may cover please contact BISSELL Customer Care by E mail telephone or regular mail as described below Limited one Year Warranty Subject to the EXCEPTIONS AND EXCLUSIONS identified below upon receipt of the product BISSELL will repair or replace with new or remanufactured components or products at BISSELI s option free of charge from the date of purchase by the original purchaser for one year any defective or malfunctioning part See information below on If your BISSELL product should require service This wagen does not apply to fans or routine maintenance components such as filters belts or brushes Damage or malfunction caused by negligence abuse neglect unauthorized repair or any other use not in accordance with the user s guide is not covered If your BISSELL product should require service Contact BISSELL Customer Care to locate a BISSELL Authorized Service Center in your area If you need information about repairs or replacement parts or if you have questions about your warranty contact BISSELL Customer Care
9. nd ordinances Grounded Outlets A WARNING Improper connection of the equipment grounding conductor can result in a risk of electrical shock Check with a qualified electrician or service person if you aren t sure if the outlet is properly grounded DO NOT MODIFY THE PLUG If it will not fit the outlet have a proper outlet installed by a qualified electrician This appliance is designed for use on a nomi nal 120 volt circuit and has a grounding attachment plug that looks like the plug in the drawing above Make certain that the appliance is connected to an outlet hav ing the same configuration as the plug No plug adapter should be used with this appliance Product view j Power Cord Handle Upper Handle Tank Carry Handle Release Back Carry Handle Flow Indicator Handle Detent Dirty Water Tank Clean Water Tank Front Carry Handle WAR N l N G To reduce the risk of fire and electric shock due to internal component damage use only BISSELL cleaning fluids intended for use with the deep cleaner Non BISSELL cleaning solutions may harm the machine and void the warranty SALES SERVICE PARTS CALL 1 877 977 3339 JanitorialEquipmentSupply com Cleaning fluid Keep plenty of genuine BISSELL 1X formula on hand so you can clean and protect whenever it fits your schedule Always use genuine BISSELL deep cleaning formulas Non BISSELL cleaning solutions may harm the machine
10. ord side down 4 Looking at the bottom of the unit find the center of the brush carriage where the carriage latch is located It is between the brush assembly and wheels 5 Pull the brush carriage towards you with one hand until it stops Pinch the car riage latch with the other hand while pulling the carriage towards you The carriage should swing out to access brush end cover 6 Remove three screws from endcap Pull endcap off to release brush roll 7 With cover removed the brush comes out easily by tilting the loose end out of the carriage 8 To replace the brush roll back into the unit place the large open end of the brush onto the carriage and tilt opposite end back into place 9 With the brush sitting relatively straight up and down by itself place endcap back on top and replace three screws The brush will need to be held and cen tered to the cover while placing it back on 10 Spin the brush by hand to make sure it turns freely with some minor resistance from the motor Push brush carriage back into place with a light pull against the lock Troubleshooting A WARNING To reduce the risk of fire electric shock or injury turn power OFF and disconnect plug from electrical outlet before performing maintenance or troubleshooting Reduce Spray or No Spray Possible causes Remedies l1 Water tank may be empty l Fill dean tank with hot tap water 2 Tank may not be seated completely 2 Turn
11. our forward and backward strokes are completed at a slower pace 5 Front nozzle of machine is clogged 5 Use fingers to remove any debris from this area 6 Upper body filter is clogged 6 Use fingers to remove any debris from this area Other maintenance or service not included in the manual should be performed by an authorized service representative Thank you for selecting a BISSELL product Please do not return this product to the store Replacement parts Item 2 3 A 5 6 7 8 9 1 6 Accessories Item Part No 1 203 6651 2 203 6652 3 203 6653 4 203 6654 5 203 6655 6 203 0116 7 203 7240 8 3063 9 31B6 1 2 6 7 vum XB Part No 203 7451 203 7452 203 7453 203 7454 203 7455 203 7456 203 7457 203 7458 203 7459 203 7460 gp Part Name Float Dirty tank assembly Dirty tank gasket Clean tank assembly Clean tank cap assembly Nozzle gasket Nozzle assembly SALES SERVICE PARTS Brush CALL 1 877 977 3339 Brush endcap JanitorialEquipmentSupply com Belt Part Name 3 Tough Stain Tool Powered TurboBrush Hand Tool 4 Upholstery Tool 6 Stair Tool Spraying Crevice Tool 2 in 1 Crevice Tool Oxy Gen2 Tool Hose assembly 1X Commercial Cleaning Formula 4 5 C a Warranty BISSELL Commercial Deep Cleaner BG10 This warranty gives you specific legal rights and you may also have other rights which may vary from state to state If you feed additional instruction reg
12. power OFF 0 Remove and reseat tank 3 Pump may have lost prime 3 Tum power OFF 0 and then back ON I Wait one minute then depress trigger 4 Dehris filter on base is clogged 4 Use hand to remove debris DirtLifter PowerBrush does not turn Possible causes Remedies 1 The belt is off or broken l Turn power OFF O and unplug unit from outlet Follow instructions on page 14 2 The unit is in the upright position 2 Brushes only rotate when unit is reclined using the detent pedal 3 Circuit breaker on machine may have tripped 3 Turn the machine OFF 0 and unplug from outlet Check to see if foreign object is caught in brush roll Remove object Plug machine in to reset circuit breaker Cleaner not picking up solution Possible causes Remedies 1 Tanks may not be seated properly l Pick up both the dean and dirty water tanks and reseat them so they fit snuggly on the unit 2 Clean water tank is empty 2 Check fluid levels in clean water tank and refill if necessary 3 Dirty water tank has picked up the maximum amount 3 Empty dirty water tank Refill dean water tank with water of dirty water the red float door has dosed and formula Place both tanks back onto unit 4 Red float door in the tank may have dosed as a result of 4 Turn the machine OFF 0 allowing red float door to release bumping an object or moving machine back and forth too quickly into the open position Turn the unit back ON I to continue cleaning Be sure y
Download Pdf Manuals
Related Search