DAG2000-32 FXS Voice Gateway User Manual V2.0
Contents
1. Privacy Password Privacy password Group Configuration Group Users can use the same group name in different versions Community That is user name View Configuration View Name The name of description mib tree View Type There are Included and excluded options View Subtree Displayed OID of access parameters View Mask The same with equipment subnet mask Generally don t configure Access Configuration Group Fill in group name Sec level There are two methods authentication and authpriv If select authentication users will just configure authentication information but not privacy information Read Read parameters of mib view Write Write parameters of mib view Notify Equipment send notify parameters to NM server ee Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Trap Configuration Trap Flag Version of SNMP Trap IP Device to inform the NM server s IP address The IP can be configured the same with source IP in community also be different Trap Port Default service port is 162 Trap Community The same with community in community configuration Note After configuration please restart equipment to take effect Users can manage and configure gateway on remote NM server through SNMP configuration But in order to security recommend this option to open when needed 4 11 2 Syslog Parameter Syslog is a prot2. 3 Both DAG serial and other VolP Device can be connected through a router using public or private IP addresses with necessary port forwarding or DMZ Operation Process 1 Pick up the analog phone then dial 47 2 Enter the target IP address Note No dial tone will be played between step 1 and step 2 Examples If the target IP address is 192 168 0 160 the dialing convention is 47 then 192 168 0 160 Followed by pressing the key or wait 3 seconds Complete Signaling interactive soon after he was called the unit can be heard ringing Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Note You cannot make direct IP calls between FXSO to FXS1 since they are using same IP It only supports the default destination port 5060 2 2 Call Hold Place a call on hold by pressing the flash button on the analog phone if the phone has that button Press the flash button again to release the previously held Caller and resume conversation If no flash button is available use hook flash toggle on off hook quickly You may drop a call using hook flash 2 3 Call Waiting Call waiting tone 3 short beeps indicates an incoming call if the call waiting feature is enabled Toggle between incoming call and current call by pressing the flash button First call is placed on hold Press the flash button to toggle between two active calls 2 4
3. DINSTAR DAG2000 32 FXS Voice Gateway User Manual V2 0 File Name Document Version Firmware Version Date Revised by Revision Records DAG2000 32FXS Voice Gateway User Manual 2 15 02 02 2012 03 16 Technical Support Department Table of Contents Equipment Introduction EE 1 1 1 Overview eege 1 1 2 Equipment appearances EE 1 Lcd POW SE SUDD A iced teinneiocetaih inter secmiccinetndetiteinr ecmiecnteiube 1 1 4 Network ee e an EE 2 1 5 Functions DEE e 2 1 5 1Protocol Standard supported EE 2 1 5 2 Voice and Fax PalaMeters cictcintsssteinisicinadsuisialiviemendiaatdialdweenas 3 1 5 3 Supplementary service 3 Basi ODE e EE 4 Fal PRONE EE 4 2 1 1 Phone or Extension NUMDer ege 4 2 1 2 Direct IP Calls ENEE 4 Zid Call Holda agaa a E RE 5 2 3 Call Wait Ng EE 5 2 04 Coll EE EE 5 2 4 1Blind DANSE RMS Sn 5 2 4 2 AtLend diT ANS ess sonate Anis 6 2 4 3 3 way Conference 6 2o Call Features ee ee 7 2 6 Sending and Receiving Fax ENEE 8 2 6 1 DAG FXS support four fax modes 8 2 6 2 T 38 and Pass Through ccccccccceceessssseseeeeeeeeeeeessssettseeeeeeees 8 Local INRsO Del all ONG nr nr tete tn 9 3 1 Inquire IP e elle 9 32 Facto RESET n E E EN 9 3 3 Configure LAN Port s IP Address 9 WEB Configuration TEE 10 AL WEB EIER ss a hii icc E E EE 10 EN oN Un EE 10 GE Le le WEE 11 E E giele WEE 12 4 3 State and EE 13 4 3 1 System Information EE 13 4 3 2 Registration Inform
4. Figure 4 3 2 Port and Port group registration information 4 3 3 TCP UDP Statistics TCP UDP Traffic Refresh Figure 4 3 3 TCP UDP Statistics Information Figure 4 3 3 shows TCP sending and receiving UDP sending and receiving packets of statistical information since the device launched 14 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual 4 3 4 RTP Session Statistics RTP Session Figure 4 3 4 RTP Session Statistics Figure 4 3 4 display real time RTP conversation flow data information includes Port voice codec packet period local port peer IP peer port sent packets receive packets lost packets jitter and duration 4 4 Quick Setup Wizard Quick configuration guide will guide users to configure the device step by step Users only need to configure network SIP server and sip port in quick setup wizard Basically after these three steps users are able to make voice call through device 4 5 Network Configuration 4 5 1 Local Network DAG 2000 series have 4 Ethernet ports and similar to a smaller switches Network configuration below Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Local Network Network Configuration Link Speed amp Duplex Auto Detect Obtain an IP address automatically Use the following IP address IP Address 72 16 50 72 Subnet Mask 55 255 0 0 Default Gateway 72 16 15 D PPPoE Account Password S
5. e TCP Transmission Control Protocol e UDP User Datagram Protocol e RTP Real Time Protocol e PPPOE point to point protocol over Ethernet e VLAN Virtual Local Area Network e ARP AddressResolution Protocol e CID Caller Identity e DND Do NOT Disturb e DTMF Dual Tone Multi Frequency e NTP Network Time Protocol e DMZ Demilitarized Zone e STUN Simple Traversal of UDP over NAT e PSTN Public Switched Telephone Network 54 Dinstar Technologies Co Ltd
6. i o Ku Max Time CID Type on LO in Message Type Send CID before Ringing Delay of Sending CID after Ringing CFNRy Timeout SLIC Setting 600 Ohm mn w E 3 Ku Ku Figure 4 8 1 FXS Parameters Configuration Interface 23 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual FXS parameters description Hear the dial tone when pick up the phone Choose the national standards Call Process Tone f from the drop down box Default is the United States With the help of dialing timeout you can limit the time while users typing a the digits from an extension If the timeout expire while the user is typing in Timeout for dialing the extension then DAG will consider the extension as complete and it will try to send to SIP server Default value is 4 seconds Timeout for This timer set how long the caller party waiting whenmakes outgoing call on answer Outgoing call extension Timeout for ae KA This timer set how long the phone sets ringing when get incoming call answer Incoming call Send Polarity Reversal Enable polarity reversal to billing A protruding button where putting the receiver boards called Flash Always press is hang up pick up the receiver the fork lift machine from reed called by hand clap called Hook flash Hook flash is a process that put the flash fast by pressing and let go In essence is to cut off the dc acce
7. 0 4095 a Voice 802 1P Priority 0 7 CE Voice VLAN uses following separate IP interface Obtain an IP address automatically Use the following IP address IP Address Subnet Mask Default Gateway Voice VLAN DNS Server Obtain DNS server address automatically Use the following DNS server addresses Management VLAN Enable Management 802 1Q VLAN ID 0 4095 BE Management 802 1P Priority 0 7 Management VLAN uses following separate IP interface Obtain an IP address automatically Use the following IP address IP Address Subnet Mask Default Gateway Management VLAN DNS Server Obtain DNS server address automatically Use the following DNS server addresses Note The device must restart to take effect Figure 4 5 3 VLAN parameter configuration Table 4 5 1 VLAN parameter configuration 18 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Fill out an ID to describe a data VLAN group D 0 used Data 802 1Q VLAN ID 0 4095 to management VLAN can t used to service Data VLAN configure 802 1p protocol to Control network traffic priority Data 802 1p Priority 0 7 Bt Priority from 0 7 Fill out an ID to describe a voice VLAN group ID 0 Voice 802 1Q VLAN ID 0 4095 used to management VLAN can t used to service configure 802 1 protocol to control network traffic priority Voice VALN Voice 802 1p Priority 0 7 BO Priority fr
8. 3 Do not shut down when the device is uploading Figure 4 11 3 Firmware upload Configuration 4 11 4 Data Backup The process data backup 1 Click Data Backup 2 Click Backup to backup data to PC Data Backup Click Backup for download configuration file to your computer Figure 4 11 4 Data Backup Interface 49 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual 4 11 5 Data Restore The processes of data restore 1 Click Data Restore 2 Browse file select data file 3 Click Restore and then import successfully the device will restart automatically Data Restore Send data file from your computer to the device Configuration NE Figure 4 11 5 Data Restore Interface 4 11 6 Ping Test Send test data packets to IP check each other whether have response and statistical response time It is ping Used to test internet and analyzed network fault Application format Ping IP address It is used to check the network connectivity or network connection speed command Pinginstructions 1 Click ping test 2 Fill IP address or domain connected click start 3 Received a message indicates that network connection normal or network connected to a fault 50 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Ping Test Destination Number of Ping 1 100 Packet Size 56 1024 bytes Inform
9. Call Transfer 2 4 1Blind Transfer Blind transfer used to transfer call to the third party without inform caller Assume that call Caller A and B are in conversation A wants to Blind TransferB to C 1 Caller A presses FLASH on the analog phone to hear the dial tone 2 Caller A dials 87 then dials caller Ce number and then or wait for 4 seconds 3 Caller A will hear the confirm tone Then A can hang up Note Call features enable must be set to Yes in web configuration page Caller A can place a call on hold and wait for one of three situations 1 A quick confirmation tone similar to call waiting tone followed by a dial tone This Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual indicates the transfer is successful At this point Caller can either hand up or make another call 2 A quick busy tone followed by a restored call on supported platforms only This means the transferee has received a 4xx response for the INVITE and we will try to recover the call The busy tone is just to indicate to the transferor that the transfer has failed 3 Continuous busy tone The phone has timed out 2 4 2 Attended Transfer Attended transfer allowsusers to confirm the third party response and decide whether to answer the calls and then transfer this call to the third party Assume that Caller A and B are in conversation Caller A wants to Attend Transfer B t
10. Calls from Analog Line Routing before Manipulation This option determines the following routing of call take effect before or after manipulation 39 Dinstar Technologies Co Ltd DINSTAR 4 9 4 P Tel Routing IP gt Tel Routing Add Index Description Calls from Caller Prefix Callee Prefix Calls to DAG2000 Series FXS Voice Gateway User Manual EE nn D IPTrunk Any EN SIP Server NOTES any in Callee Prefix or Caller Prefix means wildcard string Figure 4 9 4 IP Tel Routing Parameter Index Routing priority 0 31 0 is the highest priority Pa its purpose is so you can identify thel PO gt Tel routing with a Description meaningful name Calls from IP Trunk SIP Server any means any IP Caller number Prefix its length normally less or equal to caller number f which helps to matching routing exactly if caller number is 2001 the Caller Prefix l caller prefix can be 200 or 2 any means match any caller number like bob1 29801 Called number Prefix its length normally less or equal to callednumber f which helps to matching routing exactly if called number is Callee Prefix 008675526456659 the called prefix can be 0086755 or 00 any means match any called number Calls to This call routing is routing to port or port group Dinstar Technologies Co Ltd 40 DINSTAR DAG2000 Series FXS Voice Gateway User Manual 4 9 5 Tel 1P Tel Routing Te
11. Flash memory The DAG acquires its IP address from the first DHCP server it discovers from the LAN it is connected IP Address Using the PPPoE feature set the PPPoE account settings The DAG wille stablish a PPPoE session if any of the PPPoE fields is set Static IP mode configure the IP address Subnet Mask Default Router IP address DNS Server 1 primary DNS Server 2 secondary fields These field sare set to zero by default DNS Server Display DNS server IP address and default gateway information System Uptime Time elapsed from device power on to now Network Traffic Total bytes of message received and sent by network port Statics Includes product mode software version hardware version and built time etc 13 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual 4 3 2 Registration Information Port Registration Information Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered Unregistered oo N OO amp WIN OH
12. between and including the two The subrange construct can only be used inside a range construct i e between and 6 Wildcard x matches any digit O to 9 7 Modifiers Match 0 or more times 8 Modifiers Match 1 or more times 9 Modifiers Match 0 or 1 times Example Assume we have the following digit maps 1 XXXXXXX x11 31 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual and a current dial string of 41 Given the input 1 the current dial string becomes 411 We have a partial match with xxxxxxx but a complete match with x11 and hence we send 411 to the Call Agent 2 2 8 XXXXXX 13XXXXXXXXX Means that first is 2 3 4 5 6 7 or 8 followed by 6 digits or first is 13 followed by 9 digits 3 13 15 18 xxxxxxxxx Means that first is 13 15 or 18 followed by 8 digits 4 1 357 9 xx Means that first is 1 2 3 or 5 or 7 8 9 followed by 2 digits 4 8 6 Feature Codec Feature codec includes device function and call function Feature codec as follow Feature Code Feature Codes Use Default Status Device Function Inquiry WAN IP 159 Inquiry Phone Number 114 ER Setting IP Mode 150 Configure IP Address k Lien Network Subnet Mask Configure bey Se Network Gateway Configure 456 Renew DHCP Access WEB by WAN in Route Mode 160 Reset Factory 166 Restart Device 111 SE
13. click start Tracert Test Destination Max Hops 1 255 Information Figure 4 11 7 Tracert Test Interface 4 11 8 Password Modification Includes WEB username and password Telenet username and password modify Note Default web and telnet username and password is admin admin Password Modification Web Config Old Web Username Old Web Password New Web Username New Web Password Confirm Web Password Telnet Config Old Telnet Username Old Telnet Password New Telnet Username New Telnet Password Confirm Telnet Password 52 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Figure 4 11 8 Password Modification Interface 4 11 9 Factory Reset Click Apply to restore the factory settings Factory Reset Click the button below to reset to factory default settings Figure 4 11 9 Factory Reset Interface 4 11 10 Device Restart Click the Save button in the Configuration page to save the changes to the equipment configuration The following screen confirms that the changes are saved If the changes need restart reboot or power cycle the equipment to make the changes take effect Restart Click the button below to restart the device Figure 4 11 10 Device Restart 53 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual 5 Glossary e DNS Domain Name System e SIP Session Initiation Protocol
14. four fax modes 1 T 38 FoIP 2 Pass Through 3 Modem 4 adaptive 2 6 2 T 38 and Pass Through T 38 is the preferred method because it is more reliable and works well in most network conditions If the service provider supports T 38 please use this method by selecting T 38 8 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual as fax mode default If the service provider does not support T 38 pass through mode may be used If you have problems with sending or receiving Fax toggle the Fax Tone Detection Mode setting 3 Local IVR Operation 3 1 Inquire IP address Analog phone connected with FXS ports of device then pick up after dial tone dialing 158 to inquire LAN port IP address and dialing 159 to inquire WAN port IP address 3 2 Factory Reset After picking up dial 166 000000 then onhook and restart after Setting successful 3 3 Configure LAN Porte IP Address Before configuration please ensure 1 The device is power on 2 deviceis connectingto network 3 Telephone is connecting to FXS port of device 1 Configure dynamic IP address by DHCP Offhook Dial 150 2 Onhook If the equipment hint success after 10 seconds and restart the equipment Power off then power on 2 Configure Static IP address Offhook Dial 150 1 Onhook Then configure IP and mask as follow e Configure IP address Offhook input 152 172 16 0 1
15. gt Tel Callee 43 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual 4 10 3 Tel IP Callee Tel gt IP Callee Add Desoipton a Calls from Port Port Group Calls to Port Por croup Tr Orton ay T SIP Server Stripped Digits from Left Stripped Digits from Right Prefix to Add Suffix to Add Number of Digits to Leave from Right ok Reset Cancel NOTE any in Callee Prefix or Caller Prefix means wildcard string Figure 4 10 3 Tel IPCallee Configuration parameters are the same with Tel gt 1P Caller 44 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual 4 11 Maintenance 4 11 1 SNMP Parameter SNMP Parameter SNMP Enable Yes No SNMP Version e Community Configuration Community Source Notice default value of source is defaultif other value please input IP eg 192 168 1 1 Group Configuration Group Community wt Co l GG 2nd z View Configuration ViewName ViewType ViewSubtree ViewMask Notice ViewSubtree style x x xX xX x if just one style x Access Configuration v1 v2c Group Read Write Notify sL Le L BC W le O W LR Le ag WI WI WW Notice Read Write Notify value refrence to ViewName H Read Write Notify want to have value please firstly slelect Group Trap Configuration TrapFlag TraplP TrapPort TrapCommunity ist Fass Notice 1
16. web configuration interface mainly includes navigation tree and the right configuration interface Choose navigation tree in order to entry into the configuration interface Status amp Statistics System Information Registration TCP UDP Traffic RTP Session Quick Setup Wizard Network SIP Server Port Advanced Call amp Routing Manipulation Maintenance Figure 4 2 1 Navigation Tree When device is in bridge mode navigation tree won t display routing configuration items and the following DHCP service DMZ host forward rules and static routing and ARP etc 12 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual 4 3 State and Statistics 4 3 1 System Information System information interface shows the run information as following figure 4 3 1 below System Information MAC Address 00 1F C3 56 22 09 IP Address 172 16 50 72 255 255 0 0 Static DNS Server 0 0 0 0 0 0 0 0 System Uptime 1h 59m 40s Network Traffic Stat Received 3935726 bytes Sent 391659 bytes Version DAG2000 32S 2 15 02 02 PCB 1 LOGIC 0 BIOS 1 Built on Apr 19 2012 11 37 56 Figure 4 3 1 System Information System information as follow Table 4 3 1 System Information Description MAC address WAN port hardware address The device ID in HEX format Shows LAN IP address of DAG DHCP mode all the field values for the Static IP mode are not used eventhough they are still saved in the
17. 00 onhook e Configure subnet mask Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Offhook input 153 255 255 0 0 onhook e Configure gateway IP address Offhook input 156 172 16 0 1 onhook 3 Query the IP address of device Offhook input 158 4 If the DAG serial uses PPPoE method to get IP address it need to configure by web browser Note The telephone will play voice prompt Setting successfully if the step is correct 4 WEB Configuration 4 1 WEB Login Device is connecting to network properly refer to chapter 3 Operation Offhook and da 158 to inquire device IP address 4 1 1 Login Device LAN port default IP address is 192 168 11 1 WAN port default obtain IP address by DHCP Advice to modify the IP address of the local computer equipment and ensure that are on the same IP segment with Windows 7 as an example the local computer IP address change for 192 168 11 10 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Internet Protocol Version 4 ICPAPY4 Proper Ges Lo ieas General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address Subnet mask Default gateway O
18. RFC2833 is selected RFC2833 Payload Type Optimization payload negotiation parameter with remote side it includes two options Local and remote RFC2833 Payload Type Payloadvalue default is 101 DTMF Gain Default is 0 DB DTMF Send Interval DTMF send signal interval default is 200ms DAG supports G729 G711U G711A G723 while Coder Name it make outgoing call G 729 will used as figure 4 8 2 displayed Each kind of coding has a unique type load Payload Type value refer toRFC3551 25 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Default is disable if enable according to the current noise environment dynamically adjust mute inhibit threshold thus in the user in silent state stop transmission background noise bag Slience Suppression and save about VoIP bandwidth In the low bandwidth environment can reduce the network congestion greatly improving VolP call effect 4 8 3 SIP Parameter SIP Parameter SUBSCRIBE for MWI Message Waiting Indicator Voicemail User ID RFC3407 Support Enable IP to IP Call Enable URI includes user phone Enable Only Accept Calls from Server Enable Anonymous Call Enable Reject Anonymous Call Enable as Ending Dial Key Enable PRACK Enable Value of Refer To refers to Contact Enable RTP Mode in SDP when Call Holding Sendonly Domain Query Type A Query Domain Re resolution In
19. S CESSER Call Function Call Holding Call by IP Vi Call Waiting Activate Call Waiting Deactivate 50 Dinstar Technologies Co Ltd 32 DINSTAR DAG2000 Series FXS Voice Gateway User Manual Blind Transfer 97 Call Forward Unconditional Activate 72 Call Forward Unconditional Deactivate 73 Call Forward Busy Activate Call Forward Busy Deactivate 9 Call Forward No Reply Activate Call Forward No Reply Deactivate 03 Enable Enable Enable Enable 4 4 4 4 Enable sl Jelli ei I Je 4 J D gt a to co Nj o E a Do Not Disturb Activate Do Not Disturb Deactivate Dial Voicemail wo Enable Enable 4 N lt Figure 4 8 10 Feature Code Configuration Interface Inquire WAN port IP address Dial 159 to obtain device WAN port IP address Inquire Phone Number Dial 114 to obtain port account 150 0 means pppoe modem 150 1 means static IP Setting IP Mode 150 2 means obtain IP address by DHCP 150 3 means pppoe 157 0 set network work mode to routing mode 157 1 set Network Work Mode network work mode to bridge mode Configure IP Address 152 IP set gateway IP address Network subnet mask configure 153 subnet mask set gateway subnet mask Network Gateway Configure 156 gateway IP set gateway Renew DHCP 193 set dynamic IP again Allow access web through WAN port 160 1 don t allow access Acces
20. The only one is effective between v1 and v2c Figure 4 11 1 1 SNMP Parameter V1 V2 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Simple Network Management Protocol SNMP is application layer protocol and used to manage communication line This equipment supported three versions V1 V2C and V3 In addition to V3 version the other two versions do not support encryption However the service is usually located on the edge of the network devices security risk it is best to disable to be used again Community Configuration Community The name of network management server managed equipment Source Network management server address Group Configuration Group Name of community group different versions can use a same group name Community Community join the group View Configuration View name The name of description mib tree View type There are Included and excluded options View subtree Displayed OID of access parameters View mask The same with equipment subnet mask Generally don t configure Access Configuration V1 Group Joined community groups V2c Read Read parameters of mib view Write Write parameters of mib view Notify Equipment send notify parameters to NM server Trap Configuration Trap Flag Version of SNMP Trap IP Device to inform the NM server s IP address The IP can be configured the same with source IP in community also b
21. ameter description Primary SIP Server IP SIP Server IP address or Domain name provided by VoIP service provider Primary SIP Server port Service port default is 5060 protects registrar against excessively frequent registration refreshes Register interval while limiting the state Every once in a while send request for registration to the terminal server default is 1800s Heartbeat Heartbeat message detect the connection status between device and SIP server Secondary SIP Server IP f f dd Backup SIP Server s IP address or Domain name provided by VolP service provider address Secondary SIP Server port Service port default is 5060 protects registrar against excessively frequent registration refreshes Secondary SIP server aes i f while limiting the state Every once in a while send request for registration to the Register interval terminal server default is 1800s Secondary SIP heartbeat Heartbeat message detect the connection status between device and SIP server Use Random Port Random SIP service ports for DAG Set Local SIP port Default SIP service port is 5060 21 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual 4 7 Port Configuration Port parameters include Send gain receive gain primary display name etc Disable Enable Enable Enable Disable Enable Enable Enable Disable Enable Enable Enable Disable Enable Enable Enable Disable Enable Enable Enab
22. ation Figure 4 11 6 Ping Parameter Interface 4 11 7 Tracert Test Tracert is trace router and used to tracking routing Tracert sends a sequence of Internet Control Message Protocol ICMP echo request packets addressed to a destination host Determining the intermediate routers traversed involves adjusting the time to live TTL aka hop limit Internet Protocol parameter Frequently starting with a value like 128 Windows or 64 Linux routers decrement this and discard a packet when the TTL value has reached zero returning the ICMP error message ICMP Time Exceeded Tracert works by increasing the TTL value of each successive set of packets sent The first set of packets sent have a hop limit value of 1 expecting that they are not forwarded by the first router The next set have a hop limit value of 2 so that the second router will send the error reply This continues until the destination host receives the packets and returns an CMP Echo Reply message Trace route uses the returned ICMP messages to produce a list of hops which usually consists of routers and layer 3 switches that the packets have traversed The timestamp values returned for each router along the path are the delay aka latency values typically measured in milliseconds for each packet 51 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Tracert introduce 1 Click tracert test 2 Fill IP address or domain connected
23. ation EE 14 4 33 TCP UDP e e 14 4 3 4 RTP Session Statistics eege 15 4 4 Quick Setup Wizard 15 4 5 Network Ee r el le EEN 15 4 5 1 Local N WOTR Eed 15 4 92 VLAN eu E EE 17 E 19 EE eebe 20 EE EE 22 Ee LIVE OGL WEE 23 4 8 1 ee 23 4 8 2 Media Parameter adc ciiessiei tae E 24 nn EE 26 48 4 Fax tee 29 4 8 5 Digit Map Sanaa ANA AA NAN dada 30 4 8 6 Feature Codec ana Ananas AS SNS SN AS 32 GE TEE 34 E ROUTING EE 36 4 9 1 Port Group E 36 4 92 P riet 38 4 9 3 Routing Configuration wis cca cetera sar svia a arrenannsaiananevariecerenax evarinsaviers 39 4 9 4 IP Tel Routing iiccistesesdsdewcrsdedeeisdadacdedidsa sid adened chedbsdsdadesstedact 40 4 9 5 Tel IP Tel Routing RE 41 4 10 Manipulation Confguration 42 EN Ee 42 eelere 43 ASLO Ke 44 RE EEE 45 4 11 1 SNMP Parameter 45 4 11 2 Syslog Parameter WEE 48 4 11 3 Firmware UDO EE 49 4114 Data EE 49 4 11 5 Data Restore 50 AE LI OA PING ROSE ice SR RAR tn 50 4 Mle 7 TAC TeSt es es nn en en testinal nr nn tin 51 4 11 8 Password Modification nn nt 52 4 11 9 Factory EE 53 4 11 10 Device Restart 53 5x el EE 54 DINSTAR DAG2000 Series FXS Voice Gateway User Manual 1 Equipment Introduction 1 1 Overview Thanks for purchasing Dinstar DAG2000 32 hereinafter referred to as the DAG FXS analog voice gateway DAG2000 series FXS analog gateway is voice fax access gateway based on IP networ
24. ator E Voicemail User ID Figure4 8 6 Voice Mail Setting In SIP Parameter 3 Enable voice mail in DAG andElastix will ask you to leave a message after ringing 15 seconds thenElastixwill record and display your message Voicemail Ringtime Default 15 Direct Dial Voicemail Prefix ai Direct Dial to Voicemail message type Unavailable Optional Voicemail Recording Gain Do Not Play please leave message after tone to caller a Figure 4 8 7 Voicemail Setting 4 DAG dial 200 then dial voicemail account and thenask password for Validation After that the user will hear voice message 4 8 4 Fax Parameter Fax introduction DAG fax parameter includes fax mode Fax sound detection party ECM Rate Fax Config Mode Adaptive Tone Detection by uto ECM Enable Rate 14400 bps Figure 4 8 8 Fax Parameter Configure Interface Fax parameter description Mode Fax mode support T 38 T 30 Pass through Modem Adaptive 29 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Tone Detection by Fax sound detection mode Caller Callee Automatic Fax error correction information The rate of sending and receiving 4 8 5 Digit Map Digit Map NOTE Length of Digit Map should not be more than 119 characters Figure 4 8 9Digit Map Gateway is collect digits dialed by user if received a number to be immediately report the efficiency is too low and a large numb
25. btain DNS server address automatically Use the following DNS server addresses Preferred DNS server OT e Alternate DNS server Validate settings upon exit Figure 4 1 1Modify IP address Check connection between computer and device click Start gt run gt input cmd run ping 192 168 11 10 t order to check the connectivity between them 4 1 2 Login WEB Open web browser then input IP address of device Press Enter it pop up logging on identity authentication interface Authentication Required X The server 172 16 77 10 80 requires a username and password The server says Web Config System User Name admin Password Figure 4 1 1 DAG FXS Login Interface Default username and password admin admin click OK to entry into web interface 11 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual System Information Quick Setup Wizard MAC Address 00 1F C3 56 22 09 Status amp Statistics Network IP Address 172 16 50 72 255 255 0 0 Static SIRENE DNS Server 0 0 0 0 0 0 0 0 Port Advanced System Uptime 1h 56m 42s Call amp Routing v Network Traffic Stat Received 3777665 bytes Sent 254709 bytes Manipulation Maintenance Version DAG2000 32S 2 15 02 02 PCB 1 LOGIC 0 BIOS 1 Built on Apr 19 2012 11 37 56 Figure 4 1 2 DAG Configure Interface 4 2 Navigation Tree DAG series voice gateway
26. c descending when system selects ports Priority it always begin from the number before to the number selected last time if the minimum priority number is selected last time then the next number is the maximum priority number and move in cycles like this Group ring all ports ringing at the same time 4 9 2 IP Trunk A peer to peer VoIP call occurs when two VolP phones communicate directly over IP without IP PBXs between them A peer to peer call can be initiated directly by dialing destination phone Dinstar Technologies Co Ltd 38 DINSTAR DAG2000 Series FXS Voice Gateway User Manual number in DAGs and also receiving incoming calls from other peer to peer gateway IP trunk is help to DAGs establish peer to peer call between DAGs and other VoIP phones IP trunk will be used in routing configuration IP Trunk Add Index Description Remote Address Remote Port Heartbeat Enable Figure 4 9 2 IP Trunk Configuration Interface Index IP trunk number it is range from 0 to 63 KR The description of IP trunk its purpose is so you can identify the IP trunk with a Description meaningful name Remote Address Peer IP address or domain name Remote Port Peer SIP port Heartbeat Default is disable if enable DAG will send OPTION to peer device 4 9 3 Routing Configuration Figure 4 9 3 Routing Parameter Configuration Interface Routing Parameter Calls from IP Routing before Manipulation
27. dd Suffix to Add Number of Digits to Leave from Right NOTE any in Callee Prefix or Caller Prefix means wildcard string Figure 4 10 1 P Tel Callee number configuration Calls From This call come from IP trunk or SIP server Caller number Prefix its length normally less or equal to caller l number which helps to matching routing exactly if caller number Caller Prefix is 2001 the caller prefix can be 200 or 2 any means match any caller number like bob1 29801 Called number Prefix its length normally less or equal to called number which helps to matching routing exactly if called number is 008675526456659 the called prefix can be 0086755 or 00 Callee Prefix any means match any called number Number of Digits to Leave from Starting from the right to retain the called number digits Right 42 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual 4 10 2 Tel IP Caller Tel gt IP Caller Add Index EC C2 Description EE Calls from Port Port Group il Calls to Port Port Group OOo Le IP Trunk SIP Server Stripped Digits from Left Stripped Digits from Right Prefix to Add Suffix to Add Number of Digits to Leave from Right ok Reset Cancel NOTE any in Callee Prefix or Caller Prefix means wildcard string Figure 4 10 2 Tel IP Caller Configuration parameters are the same with IP
28. e different Trap Port Default service port is 162 Trap Community The same with community in community configuration 46 Dinstar Technologies Co Ltd DINSTAR SNMP Parameter DAG2000 Series FXS Voice Gateway User Manual SNMP Enable yes No SNMP Version ME User Configuration User AuthType AuthPsssword PrivacyType PrivacyPsssword 1st notConfigUser MDS x ss DES ss Notice The length of AuthPassword snd PrivacyPassword are more than 8 Group Configuration Group Community Le View Configuration ViewName ViewType ViewSubtree ViewMask 1st all included 1 ad CL ye EEE oa CT EN CE Notice ViewSubtree style x x x xx if just one style x Access Configuration v3 Group sec level Resd Write Notify 1th e Notice Resd Write Notify value refrence to ViewNsme If Read Write Notify want to have value please firstly slelect Group Trap Configuration TrapFiag it eS TrapiP TrspPort 7216 247 85 LES TrapCommunity puti ic Notice 1 The only one is effective between v1 snd v2c 2 After complete configure plesse restart the device to take effect Figure 4 11 1 2 SNMP Parameter V3 User Configuration User Network management server management device by username Auth Type Supported two auth type MD5 and SHA Auth Password Authentication password Privacy Type Supported three privacy type DES AES and AES128
29. er does not participate in the media process In SIP network the media always using end to end to hand the consultation In some particular situation or business processing such as Music On Old SIP server will actively participate in the media negotiation Simple SIP server is responsible only for establishment maintenance and cleaning conversation don t interfere in call While relatively complex SIP server also called SIP PBX It not only provides the basic call and basic conversational support also offer plenty of business such as Presence Find me Music On Hold 3 SIP server based on Linux platform such as OpenSER sipXecx VoS Mera etc 4 SIP server based on windows platform such as miniSipServer Brekeke VolPswitch etc 5 Carrier grade soft switch platform such as Cisco Huawei Zteetc SIP server configuration interface as follows 20 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual SIP Server Primary SIP Server Primary SIP Server Address 172 16 100 102 Primary SIP Server Port Default 5060 5060 5060 Register Interval Default 1800 1800 S Heartbeat ElEnable Secondary SIP Server Secondary SIP Server Address PRS reene Ar SE Default 5060 Soen Register Interval Default 1800 1800 S Heartbeat JEnable Local SIP Port Use Random Port JEnable Set Local SIP Port 5060 Figure 4 6 1 SIP Server Configuration Interface SIP par
30. er of take up network resources A reasonable method is concentration sending a message after receiving all number How to judge the gateway receiving all number is the difficulties of this method The solution is the call agent loading a Digit Map to gateway Digit Map includes a series figure characters when the dial up sequence and one received a character string matching it means the number has received neat Digital string contains characters allowed data0 9 letterA D letter T letter x and parts of each string is a choice of dial up solutions means choose anyone means one reports letter T an means detected timer overtime x means any data means multiple characters can be behind include 0 means report immediately 30 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Digit Map Syntax 1 Supported objects Digit A digit from 0 to 9 Timer The symbol T matching a timer expiry DTMF A digit a timer or one of the symbols A B C D or 2 Range One or more DTMF symbols enclosed between square brackets and but only one can be selected 3 Range One or more expressions enclosed between round brackets and but only one can be selected 4 Separator Separated expressions or DTMF symbols 5 Subrange Two digits separated by hyphen which matches any digit
31. ervice Name DNS Server Obtain DNS server address automatically Use the following DNS server address Primary DNS Server Secondary DNS Server Note The device must restart to take effect Figure 4 5 1Route Mode e Link Speed amp Duplex used to select Ethernet port work mode include 5 kinds of choice Auto Detect 10Mbps half duplex 10Mbps full duplex 100Mbpshalf duplex 100Mbps full duplex default is Auto Detec e When select Obtain IP address automatically DAG will obtain IP address by DHCP e When select Use the following IP address that configure DAG to fixed IP address mode e When select PPPoE please fill in account and password offered by ISP in internet account and password Notes 1 If select DHCP to obtain IP address please ensure DHCP server in network and work normally 2 After configuration restart device configuration validation Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual 4 5 2 VLAN Parameter Generally Internet provides only Best Effort Service Since Ethernet is the most spread LAN access technology importance of providing it a quality of service mechanism ought not to be neglected Ethernet technology also used as WAN technology not only as LAN technology Due to rapidly increasing use Internet through Public Switched Telecommunication Network PSTN Telephone Companies are forced t
32. ery once in a while check whether a program or configuration files Check Interval need to be updated System default 24 hours WEB Port Gateway web port default is 80 Access Web by WAN Enable or disable accessing web by WAN Telnet Port Telnet service port default is 23 4 9 Call amp Routing 4 9 1 Port Group Port group parameter include Index description etc Port group configure interface as follow 36 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Port Group Add Description CCS Primary Display Name Fl Primary SIP User ID S Primary Authenticate ID LR Primary Authenticate Password Secondary Display Name Secondary SIP User ID Secondary Authenticate ID Secondary Authenticate Password Auto Dial Delay Time Port Select Cyclic Ascending Port Port o Fxs ElPort 1 FXS Port 2 FXS Port 3 FXS Port 4 FXS Port 5 FXS Port 6 FXS Port 7 FXS Port 8 FXS Port 9 FXS Port 10 FXS Port 11 FXS Port 12 FXS Port 13 FXS Port 14 FXS Port 15 FXS Port 16 FXS Port 17 FXS Port 18 FXS Port 19 FXS Port 20 FXS Port 21 FXS Port 22 FXS Port 23 FXS Port 24 FXS Port 25 FXS El Port 26 FXS El Port 27 FXS El Port 28 FXS El Port 29 FXS Port 30 FXS Port 31 FXS Figure 4 9 1 port group configuration interface fi Port group number It uniquely identifies a route range ndex from 0 7 Description Dinstar Technologies Co Ltd Port group de
33. es Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual TFTP HTTP HTTPS DNS DNS SRV RFC 1706 RFC 2782 e VLAN 802 1P 802 1Q 1 5 2 Voice and Fax parameters e G 711A U law G 723 1 G 729AB e Comfortable Noise Generation CNG e Voice Activity Detection VAD e Echo Cancellation G 168 e Adaptive Dynamic J itter Buffer e Voice and fax gain control e Modem e 7 38 Pass through DTMF Mode Signal RFC2833 INBAND 1 5 3 Supplementary service e Call waiting e Call transfer Blind transfer Attend transfer e Quick pick e Call Forwarding Unconditional e Call Forwarding on No Reply e Hotline e Call hold DND e 3 way conference 24 32 port support e Voice mail e Direct IP Call Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual 2 Basic Operations 2 1 Phone Call 2 1 1 Phone or Extension Number 1 Dial the number directly and wait for 3 seconds Default No dial timeout 2 Dial the number directly and press 2 1 2 Direct IP Calls DAG series device with FXS port allow two parties directly call through IP address The user need only a simulation with the FXS port unit equipment linked together and set up calls not registered Elements necessary to completing a direct IP call 1 Both DAG serial and other VolP Device have public IP addresses 2 Both DAG serial and other VolP Device are on the same LAN using private IP addresses
34. header There are two modes option A QUERY and SRV QUERY Domain Query Type Default is A QUERY Domain Re resolution Interval Default 0 forbidden ES T1 timer of SIP protocol default is 500ms T1 T2 T2 timer of SIP protocol default is 400ms 4 T4 timer of SIP protocol default is 500ms Dinstar Technologies Co Ltd 27 DINSTAR DAG2000 Series FXS Voice Gateway User Manual Max Timeout The max timeout of sending or receiving default is 32s Heartbeat Interval Default is 10s Voice mail instructions Here DAG work with Elastixas the example introduces how voicemail work in DAG 1 DAG register to Elastix server Corresponding extension number enable voice mail function in Elastix and set password As below Voicemail amp Directory Status Enabled Voicemail Password 111111 Email Address Pager Email Address Email Attachment C yes Play CID C yes Play Envelope C yes Delete Voicemail yes IMAP Username IMAP Password VM Options VM Context default VmX Locater Figure 4 8 4 Elastix Voicemail Configuration Interface 2 check feature code in Elastix and change it as necessary Its default feature codes setting as below Voicemail Dial Voicemail Enabled iw My Voicemail Enabled iw Figure 4 8 5 Elastix Voicemail Setting 28 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual SIP Parameter SUBSCRIBE for MWI Message Waiting Indic
35. k It can provide high efficiency high quality VolP business for operators the family office remote office and branch enterprise DAG2000 series VoIP access gateway adopted standard SIP protocol and compatible with leading IP PBX soft switch and SIP based platform DAG2000 series products used strong hardware technology solutions and have a good voice fax handling ability high stability It is the best VOIP equipment choice for commercial DAG2000 series FXS analog gateway includes following model DAG2000 16S m DAG2000 245S m DAG2000 32S This manual mainly to DAG2000 32S as example introduce the function of devices and parameter configuration 1 2 Equipment appearance Figure 2 1DAG2000 16S Figure 2 2DAG2000 32S 1 3 Power supply DAG2000 is standard rack equipment and adopts AC 110 240 V power supply Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Power parameters Input 100 240V 50 60Hz 1 4 Network Applications Elastix IPPBX Softswitch All over the world P N etwo rk FXO lines FXO VoIP Gateway AG 2000 32FXS FXO pa a Phone Phone Phone Phone Figure 4 1 Network Applications 1 5 Functions and Features 1 5 1Protocol standard supported SIP V2 0 RFC 3261 3262 3264 SDP RFC 2327 e REFER RFC 3515 RTP RTCP RFC 1889 1890 e STUN RFC 3489 e ARP RARP RFC 826 903 SNTP RFC 2030 DHCP PPPOE Dinstar Technologi
36. l gt IP Tel Routing Add Index Description Calls from Caller Prefix Callee Prefix Calls to NOTES Port Port Group SIP Server any in Callee Prefix or Caller Prefix means wildcard string Figure 4 9 5 Tel IP Tel Parameters Configuration Index Routing priority 0 31 0 is the highest priority Description its purpose is so you can identify the routing with a meaningful name Calls From Tel IP call select port or port group Caller number Prefix its length normally less or equal to caller number which Caller Prefix helps to matching routing exactly if caller number is 2001 the caller prefix can be 200 or 2 any means match any caller number like bob1 29801 Called number Prefix its length normally less or equal to called number which helps to matching routing exactly if called number is Callee Prefix i 008675526456659 the called prefix can be 0086755 or 00 any means match any called number Calls to This call routing is routing to port port group IP trunk and SIP server 41 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual 4 10 Manipulation Configuration 4 10 1 P Tel Callee IP gt Tel Callee Add Index Description Calls from IP Trunk SIP Server Caller Prefix Callee Prefix Calls to Port Port Group Stripped Digits from Left Stripped Digits from Right Prefix to A
37. le Disable Enable Enable Enable Disable Enable Enable Enable Disable Enable Enable Enable Disable Enable Enable Enable Disable Enable Enable Enable Disable Enable Enable Enable Disable Enable Enable Enable Disable Enable Enable Enable Disable Enable Enable Enable Disable Enable Enable Enable Disable Enable Enable Enable Total 32 entry Page 0 4 2 3 4 5 6 7 8 9 Di Ki Figure 4 7 1 Port configuration interface Port parameters introduce as follows It is use to control the volume of conversation Adjust TX gain will affect the Tx Gain end users voice size the default value is 0 Its value range from 10 10 dB It is use to control the volume of conversation Adjust RX gain will affect the Rx Gain end users voice size the default value is 0 Its value range from 10 10 dB Primary Secondary SIP Primary Secondary SIP account description Its purpose is so you can identify Display Name the SIP account with a meaningful name Primary Secondary User account information provided by VoIP service provider ITSP Usually in SIPUser ID the form of digit similar to phone number or actually a phone number Primary Secondary SIP SIP service subscriber s Authenticate ID used for authentication Can be Authenticate ID identical to or different from SIP User ID Primary Secondary SIP password which registers to soft switch SIP server Authenticate password Pre assign an extensio
38. n or phone number so that automatically dial a number Offhook Auto dial as Soon as you pick up the phone set Delay 0 3 seconds to automatically dial a number 0 means dial number Auto dial Delay Time immediately Do not disturb the phone set won t receive any calls in case it enabled 22 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Enable or disable caller ID for corresponding port call forward unconditional all incoming calls willforward to pre assigned Number for CFU number automatically Call forward on busy if the line is busy the call will forward to pre assigned Number for CFB number automatically Call forward no reply if the line is not answer the call the call will forward to Number for CFNRy pre assigned number automatically SS If call waiting enabled it will send a special tone if another caller tries to reach Call Waiting you when you are using your telephone Play Call Waiting Tone Enable call waiting tone caller will hear special tone 4 8 Advanced 4 8 1 FXS parameters FXS characteristic parameters include Call progress Tone Timeout for Dialing Send Polarity Reversal etc Configuration interface as follow FXS FXO Call Progress Tone Timeout for Dialing Timeout for Answer Outgoing Call n on Timeout for Answer Incoming Call FXS Parameter Send Polarity Reversal Detect Hook Flash Min Time lt
39. o C 1 Caller A presses FLASH on the analog phone for dial tone 2 Dial Caller Ce number followed by or wait for 3 seconds 3 If Caller C answers the call Caller A and Caller C are in conversation Then A can hang up to complete transfer 4 If Caller C does not answer the call Caller A can press flash to resume call with Caller B 2 4 3 3 way Conference 3 way conference 1 Caller A call B B pick up into call states 2 Caller A hook flash A and B into keep states then C call A A through to the phone 3 A hook flash then A B C into keep states at this time if A press 1 key then A and B continue to call if A press 2 key then A and B continue to call if A press 3 key then A B C three parties go to call Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Cal Call hold gt Il hold lt Cal Figure 2 4 1 3 way Conference 2 5 Call Features DAG FXS support all traditional and senior phone function Table 2 5 1 Feature Codec 158 View the LAN port IP address 193 Obtain IP address through DHCP again 111 Restart device Call hold 7 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Switch between incoming calls 1f not in session flash hook will switch a new channel for new call Flash Hook 2 6 Sending and Receiving Fax 2 6 1 DAG FXS support
40. o implement IP based networks as their PSTN backbones A network like this without any Quality of Service mechanisms would be disastrous J ust imagine yourself trying to get an emergency call through while others just surf the Internet 1 802 1Q The IEEE 802 1Q standard defines architecture for Virtual Bridged LANs the services provided in Virtual Bridged LANs and the protocols and algorithms involved in the provision of those services No Quality of Service mechanisms are defined in this standard but an important requirement for providing QoS is included in this standard e g ability to regenerate user priority of received frames using priority information contained in the frame and the User Priority Regeneration Table for the reception Port 2 802 1p IEEE 802 1p standard Traffic class expediting and dynamic multicast filtering It describes important methods for providing QoS at MAC level IEEE 802 1p is in fact quite good Lower priority level packets are not sent if there is packet in queued in higher level queues IEEE 802 1p describes no admission control protocols It would be possible to give Network Control priority to all packets and the network would be easily congested There are three VLAN data VLAN voice LAN and management VLAN VLAN configuration interface as following figure 4 4 3 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Voice VLAN Enable Voice 802 1Q VLAN ID
41. ocol used in TCP IP network transmission of record of the standard file information Syslog agreement belongs to a kind of master slave agreement Syslog sender will sent a small text information less than 1024 bytes to syslog the receiver The receiver are syslogd syslog daemon or syslog server Syslog message can be transferred by TCP UDP Syslog level none Used to misarrange e debug Not including function conditions or the question of other information notice importance common conditions warning Early warning information e error Stop error conditions of tools or some part of the realization of the function subsystem Syslog Parameter Enable Figure 4 11 2 Syslog Parameter Configuration Enable send CDR and then send communication information to syslog server 48 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual 4 11 3 Firmware Upload The process of firmware upload 1 Click Firmware Upload 2 Browse files and choose the loading program Name the file extension Idf 3 Click Upload the upload process will last about 60s and device can automatically restart after uploading The firmware update process don t shut off the power Firmware Upload Send IO file from your computer to the device Software E Web RUE HET Notes 1 The upload process will last about 605 2 The device will restart automatically after upload
42. om 0 7 IP address Can use dynamic or static IP address Voice VLAN DNS Server Can use dynamic or static DNS server address Fill out an ID to describe a data VLAN group ID 0 Management 802 1Q VLAN used to management VLAN can t used to service PES configure Management 802 1p Priority Management 802 1 protocol to control network traffic priority VLAN Priority from 0 7 IP address Can use dynamic or static IP address Management VLAN DNS server Can use dynamic or static DNS server address Note Restart the device to take configuration effect 4 5 3 ARP ARP brief introduction ARP is address resolution protocol After configuring ARP users can get physical address through device IP address Under TCP IP network environment each host is assigned a 32 bit IP address But the message transmission needs to know the purpose the physical address of the party ARP is a tool that converts IP address into MAC address ARP configuration interface as follows Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Static Dynamic Total 0 entry L El Figure 4 5 4 ARP Parameters 4 6 SIP Server SIP server introduction 1 SIP server is the main component of VolP network and responsible for establishing all the SIP phone calls SIP server also called SIP proxy server or registered server IPPBX and the soft switch can act as SIP server role 2 Usually SIP serv
43. rotocol 3 Provision Auto Provisioning can be used to provide general and specific configuration 34 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual parameters Settings to the DAGsand to manage firmware actualization System parameter configuration interface as follow System Parameter NAT Traversal Refresh Interval STUN Server Address STUN Server Port 3478 NTP Enable Primary NTP Server Address us pool ntp org Primary NTP Server Port 23 Secondary NTP Server Address 64 236 96 53 Secondary NTP Server Port SYN Interval Time Zone GMT 6 00 US Central Time Daily Reboot Enable Reboot Time Le Le Provision Parameter Primary Profile URL Secondary Profile URL Check Interval WEB Parameter WEB Port Telnet Parameter Telnet Port Save Figure 4 8 11System Configuration Interface Secondary NTP server address Default is 18 145 0 30 Secondary NTP server port Default is 123 Every certain time synchronization gateway time the system default SYN Interval every 3600 s synchronous once 35 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Time zone can be chosen System default the United States central Time Zone b time Chicago Primary Provision server IP Server IP address or domain provided by Provision server Secondary Provision server IP Server IP address or domain provided by Provision server Ev
44. s Web by Wan in Rout Mode web through WAN port 160 0 Reset Factory 166 000000 reset factory Restart Device 111 restart device When call process dial into call hold Recovery the call through Call onhold offhold hook flash or 33 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Call by IP Directly dial the end user IP to call Call Waiting Activate 51 enable call waiting function Call Waiting Deactivate 50 forbid call waiting function If the call transfer to 801 first hook flash and then dial the 87 801 Call Forward Unconditional Activate 72 phone number transfer the call from the phone number Call Forward Unconditional Note private services are open by default Blind Transfer 4 8 7 System Parameter NAT traversal has two modes STUN static NAT When select STUN STUN server should be configured select static NAT just configure NAT IP address System parameters include STUN NTP Provision WEB parameter Telnet 1 STUN STUN Simple Traversal of UDP over NATs is a network protocol It allows users back of NAT find their own public network address NAT type and internet end port have been bound by NAT for a local port Two back of NAT router devices established UDP communication through this information STUN doesn t support TCP connection and H 323 2 NTP Network Time Protocol NTP is a computer time synchronization p
45. scription its purpose is so you can identify 37 DINSTAR DAG2000 Series FXS Voice Gateway User Manual Primary Secondary Display Name Primary Secondary SIP User ID Primary Secondary Authenticate ID Primary Secondary Authenticate Password Port Select Port group display which will be used in SIP message example INVITE sip bob biloxi com SIP 2 0 Via SI P 2 0 UDPpc33 atlanta com branch z9hG4bK7 76asdhds Max Forwards 70 To Bob lt sip bob biloxi com gt From Alice lt sip alice atlanta com gt tag 1928301774 Here Bob and Alice is the display User account information provided by VolP service provider ITSP Usually in the form of digit similar to phone number or actually a phone number SIP service subscriber s Authenticate ID used for authentication Can be identical to or different from SIP User ID Password of SIP user ID e It specifies the policy for selecting port in a port group Ascending the system always selects a port from the minimum number The preferential selection of the port can be realized through this mode Cyclic ascending when system selects ports Priority it always begin from the number next to the number selected last time if the maximum priority number is selected last time then the next number is the minimum priority number and move in cycles like this Descending when system selects ports priority it always begin to select from the maximum priority number Cycli
46. ss about 80 Detect Hook flash des to 200 ms Then switches don t think it s hang on but keep the call taking some other operating The typical application of hook flash is the telephone switchboard When need to transfer the call to other extension then telephone hook flash to transfer the call CID Type There are DTMF and FSK General for the default Message Type The call display formats SDMF and MDMF General for the default After enable this configuration The DAG send caller to phone set before Send CID before Ringing ringing otherwise the caller ID will display after ringing Delay of sending CID after Definite delay timer of caller ID while it set to send caller ID after ringing Ringing Its Default value 500ms SLIC Setting Set the unit impedance 4 8 2 Media Parameter Media parameter mainly include RTP start port DTMF parameter PreferedVocoder Configuration Interface as follow 24 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Media Parameter RTP Start Port DTMF Parameter DTMF Method DTMF Gain B DTMF Send Interval 200 Send Flash Event MeEnable Prefered Vocoder Packetization Time ms d ard S an 53 Coder Name Payload Type Rate kbps Silence Suppression Figure 4 8 2 Media Parameter Configuration Interface Media parameter description RTP Start Port Default RTP port 8000 DTMF Method SINGAL INBAND RFC2833 It is configurable When
47. teval 0 means disable T1 T2 T4 Max Timeout Heartbeat Interval 1 3600s 26 Dinstar Technologies Co Ltd DINSTAR DAG2000 Series FXS Voice Gateway User Manual Response Code Switch Response Code Response Code after Switch Figure 4 8 3 SIP Parameter Configuration Interface SIP parameter description Voicemail message indicator it is to be realized in the way SUBSCRIBE for MWI of NOTIFY Voicemail User ID Access code to voicemail box RFC34077 Support Docking parameters the SDP simple ability statement Enable this function users may use the business call IP IP to IP Call address on the phone URI Includes user phone SIP carries the information the system defaults not open Default is no it indicates the DAG accept incoming call from Only Accept Call from Server SIP server only Enable anonymous call anonymous will include in SIP Anonymous Call message Enable this function reject all anonymous call Disable by Reject Anonymous Call default as ending Dial Key Dial up use as a end descriptor RFC3262 defined an optional extension methods PRACK PRACK provisional ack Used to support the reliability of the temporary response Its function is to require the receiving party contact with the third party through the use of supplied in the request in the Value of Refer To refers to Contact address information Refer to field of SIP message fill in contact
Download Pdf Manuals
Related Search