AX4E-Centos5.4-Dahdi-User Manual-V1.0-EN
Contents
1. generate etc asterisk dahdi channels conf file root localhost dahdi_genconf It does not show any output if dahdi_genconf runs successfully After running dahdi genconf successfully the system conf file will get the following configuration etc dahdi system conf Autogenerated by usr sbin dahdi_genconf on Thu Jul 1 11 33 13 2010 If you edit this file and execute usr sbin dahdi_genconf again your manual changes will be LOST Dahdi Configuration File This file 1s parsed by the Dahdi Configurator dahdi_cfg Span 1 WCTDM 6 ATCOM AX4G AX2G4A Board 7 MASTER fxsks 1 echocanceller mgz2 fxsks 2 echocanceller mg2 2 fxsks 3 echocanceller mg2 3 fxsks 4 echocanceller mg2 4 fxoks 5 echocanceller mg2 5 fxoks 6 echocanceller mg2 6 Global data loadzone defaultzone www atcom cn 9 ae ATCOM After running dahdi genconf successfully the dahdi channels conf file will get the following configuration Span 1 WCTDM 6 ATCOM AX4G AX2G4A Board 7 MASTER 33 line 1 WCTDM 6 0 FXSKS In use SWEC MG2 signalling fxs_ks callerid asreceived group 0 context from pstn channel gt 1 callerid group context default 335 line 2 WCTDM 6 1 FXSKS In use SWEC MG2 pinnum 1234 signalling fxs_ks callerid asreceived group 0 context from pstn channel gt 2 callerid group context default 33 line 3 WCTDM 6 2 FXSKS_ In use SWEC MG2 signalling fxs_2. SW100 Used for selecting the way of power feeding set it to 1 ON and 2 OFF the CONI provide s the power for the card set it to 1 OFF and 2 ON the PCI slot provides the power for the card If the FXS port is used the card must be provided power by the CONI To ensure the enough power feeding user should choose the CONI to provide power for the card and the SW100 is set to 1 ON and 2 OFF by default Hole used for fixing the line which connect the GX01 to antenna Antenna the antenna in the picture above is omnidirectional the model is TSO1 Attention In order to enhance the GSM signal in some hard environment except the Antenna in the illustration above ATCOM can also provide one other type of antenna TLO01 which has long cable about one meter long and can be connected to outside RJ45 Used for connecting a splitter to the card the splitter supports four RJ11 ports and one RJ45 port LED3 Used for checking if the FXS FXO module is detected or not When the FXS FXO ports are detected correctly the LED3 will be on www atcom cn 5 T ATCOM LED11 When the channel 1 is in communication status LED11 will be green steady LED12 Network status indicator of SIM card of the first channel When the SIM card is searching network the LED12 will blink fast when the SIM card has found the GSM network and registered successfully the LED12 will flip at lower frequency LED21 When the channel 2 is in communication status LED21 w
3. ks callerid asreceived group 0 context from pstn channel gt 3 callerid group context default 33 line 4 WCTDM 6 3 FXSKS_ In use SWEC MG2 signalling fxs_ks callerid asreceived group 0 context from pstn channel gt 4 callerid group context default eee eee ccoccc c U uU vrZsnad f TzZ c T m ueruyeucuuuUu Uu c C ccc cququg s 0 o cC_ S MwA w T T C C UU r yztwrzcrcccc www atcom cn T 335 line 5 WCTDM 6 4 FXOKS In use SWEC MG2 signalling fxo_ ks callerid Channel 5 lt 4005 gt mailbox 4005 group 5 context from internal channel gt 5 callerid mailbox group context default line 6 WCTDM 6 5 FXOKS In use SWEC MG2 signalling fxo ks callerid Channel 6 lt 4006 gt mailbox 4006 group 5 context from internal channel gt 6 callerid mailbox group context default www atcom cn T ATCOM 3 Please run dahdi cfg vv command root localhost asterisk dahdi cfg vvvvvvvvvv DAHDI Tools Version 2 3 0 DAHDI Version 2 3 0 Echo Canceller s MG2 Configuration Channel map Channel 01 FXS Kewlstart Default Echo Canceler mg2 Slaves 01 Channel 02 FXS Kewlstart Default Echo Canceler mg2 Slaves 02 Channel 03 FXS Kewlstart Default Echo Canceler mg2 Slaves 03 Channel 04 FXS Kewlstart Default Echo Canceler mg2 Slaves 04 ze ATCOM Channel 05 FXO Ke
4. please edit the file root bash profile to change the system language For example the system default language is English like this LANG es_ES you can change it to Chinese like this LANG zh_CN 8 Set the billing function If you would like to set the billing function you can edit the file etc asterisk dahdi channels conf and enable the two parameters answeronpolarityswitch yes polarityonanswerdelay 300 Then you can open the CRBT Color Ring Back Tone after you enable the parameter prematuremedia no in the file etc asterisk sip conf www atcom cn 13 A7 SD ATCOM Chapter 5 Test 1 Please check the status of the cell phone card plugged in the AX 2G4A Please type the following command three times the result of the third time is correct cat proc dahdi ax4g_sta card 1 You can get one line with the following information S0 4 S1 4 S2 0 S3 0 The SO S1 stand for the two modules on the AX 2G4A orderly and different numbers behind colon stand for different status of SIM card a it means that the cell phone card is sending SMS 1 it means that the module2 is powered off 2 1t means that the cell phone card is still searching for GSM network 3 it means that the cell phone card has registered successfully before but now it failed 4 it means that the cell phone card has found GSM network successfully and it is in idle status not used by calling or sending SMS 5 it means that after a communication one side hangs
5. the call GSM quadband frequency 850 900 1800 1900MHz DTMF detection Suitable for 3 3 volts and 5 0 volts 32 bit PCI slots PCI slot or 4 pin connector for power feeding Support Elastix 2 0 3 Trixbox 2 8 0 4 Applications GSM and analog connectivity for PBX Mobile and analog PBX GSM and analog VolP gateway SMS gateway GSM callback services Billing system Hardware Requirement 500 Mhz Pentium II 64MB RAM 3 3 V or 5V PCI 2 2 slot www atcom cn 3 ATCOM Measurement and Weight 221 142 62mm 0 25kg 174mm 104 mm Package S GSM module GX01 Dual ports analog module www atcom cn 4 J gt gt Vl ATCOM Chapter 2 Hardware Introduction AX210X AX210S Slot2 GxX01 104mm X a ieee _ Slot1 CON1 ii eee COS eee SW100 y TAN RSNA ES A gt r mN lt TO gt A Antenna ME N iG Anis si N d LED11 LED12 Antenna Interface LED2 LED22 GX01 GSM module one GX01 supports one GSM channel AX210S FXS module it supports two FXS ports AX210X FXO module it supports two FXO ports Slotl A slot for plugging GX01 it is the first channel of the card Slot2 A slot for plugging GX01 it is the second channel of the card Slot3 A slot for plugging FXS FXO module it is the third and fourth channels of the card Slot4 A slot for plugging FXS FXO module it is the fifth and sixth channels of the card CONI 4 pin power connector
6. up the phone but the other side has not hang up 6 it means that the cell phone card is dialing out 7 it means that somebody from outside is calling the channel but no extension answers the phone the extension is ringing 8 it means that an extension answers an incoming call but the communication has not yet established at this moment the called party hangs up then the caller do not need to be paid for this call because this call has not been established really 9 it means that the channel is in communication status and the call has been established really 2 Please check the network signal of the cell phone card plugged in the AX 2G4A type the following command three times the result of the third time is correct cat proc dahdi GSM_ signal card 1 you can get one line with the following information SQ0 31 SQ1 30 SQ2 0 SQ3 0 The SOU SQI stand for the two modules on the AX 2G4A orderly and different numbers behind equality sign stand for the network signal of the cell phone card the numbers 0 and 99 mean no signal for other numbers the bigger the number is the stronger the signal is 3 Check when the called party answers the call when you dial out through AX 2G4A Please use dmesg command to detect if the called party answers the call when you dail out through AX 2G 4A if the called party has answered the call after running dmesg command you can get one line with GX PR X stands for the channel number This
7. ATCOM Sant se eee eee E at SE SEEK SX S DO N RN N WEN REX yo So Beam Wey Wee CS S Qo S SN NS SAN kao C Aye gt QS ee DEI S La Z AS lt SES CR z G lt J v gO oe os S ATCO Me H P ybri roduct cone Card AX 2G4 A Version 2 1 W ritten by Rob July 7 2012 ert Ao ATCOM Content CONTACT ATCOM TTT 2 CHAPTER 1 THE INTRODUCTION OF AX 2G4A cccccococccocooco0co0o00c00c000c00c00c000000000000000000000000000000000000000000000 3 CHAPTER 2 HARDWARE INTRODUCTION cccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccscscccscccscscscccccscscscscscss 5 CHAPTER 3 SOFTWARE INSTALLATION cccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccs 7 CHAPTER 4 SOFTWARE CONFIGURATION cccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccocececececes 9 CHAPTER ET 13 CHAPTER 6 SENDING AND RECEIVING SMG ccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccccecs 16 CHAPTER 7 REFERENC CE oeooeeoseeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeseeeeeeeeeeeseeeeeseeseeseeseeseeseeeeees 18 www atcom cn o W ATCOM Contact ATCOM The Introduction of ATCOM Founded in 1998 ATCOM technology has been always endeavoring in the R amp D and manufacturing of the internet communication terminals The pro
8. UTF 8 gt lt sms gt lt receiver gt 15012871900 lt receiver gt lt receiver gt 1372873 1752 lt receiver gt lt channel gt 1 lt channel gt lt content gt hello welcom to ATCOM lt content gt lt sms gt Please copy the bulksms xml content to outgoing file run the command ep bulksms xml outgoing www atcom cn 17 A n TTT ATCOM From asterisk CLI you can get the following output if you can see the red characters result 1 it means that the SMS has been sent out successfully If you get result 1 it means that the SMS fails to send out localhost CLI gt Sep 9 16 08 23 NOTICE 3593 pbx _spool c 166 apply sms outgoing pbx spool find called name 15012871900 Sep 9 16 08 23 NOTICE 3593 pbx _spool c 166 apply sms outgoing pbx spool find called name 13728731752 Attempting call on sms for application queuesms dahdi 1 15012871900 amp 13728731752 hello welcom to ATCOM Retry 1 Launching queuesms dahdi 1 15012871900 amp 13728731752 hello welcom to ATCOM on type data 00000001 Sep 9 16 08 23 NOTICE 3823 pbx _spool c 531 attempt thread Call completed to sms Launching DoSms 150128719008 amp 13728731752 hello welcom to ATCOM on DAHDI 1 1 Sep 9 16 08 27 NOTICE 3825 chan dahdi c 18205 sms queue send sessionid 1315555703 3 channum 1 time 2011 09 09 16 08 27 send to called 15012871900 result 1 Sep 9 16 08 31 NOTICE 3825 chan dahdi c 18205 sms queue send sessionid 1315555703 3 channu
9. an refer to the following dial plan from internal exten gt _1 1 Dial dahdi 1 EXTEN 1 Dial out via GSM channels exten gt _1 2 Hangup exten gt _2 1 Dial dahdi 2 EXTEN 1 exten gt _ 2 2 Hangup exten gt _3 1 Dial dahdi 3 EXTEN 1 Dial out via FXO ports exten gt _3 2 Hangup exten gt _4 1 Dial dahdi 4 EXTEN 1 exten gt _ 4 2 Hangup www atcom cn 15 ATCOM from pstn exten gt s 1 Answer exten gt s 2 Dial sip 500 exten gt s 3 hangup 9 Use a registered sip phone to make an outgoing call according to the dial plan above if you want to make the outgoing call through the first channel you have to add a prefix 1 when you dial out if you want to make the outgoing call through the second channel you have to add a prefix 2 Here the destination number is 15128731752 so dialing 115128731752 then you can get the following output from asterisk CLI CLI gt Using SIP RTP CoS mark 5 Executing 115128731752 from internal 1 Dial SIP 500 00000003 dahdi 1 15128731752 in new stack Called 1 15128731752 DAHDI 1 1 answered SIP 500 00000003 The called party rings and pick up the phone so the call is successful 10 Please use a phone to make an incoming call here the SIM card number for the first channel is 15889587467 using a cell phone to dial 15889587467 the sip 500 rings and you can get the following output from asterisk CLI CLI gt Startin
10. duct line of ATCOM includes IP Phone USB Phone IP PBX VolP gateway and Asterisk Card Contact sales Address District C east of 2nd floor 3 Crown industry buildings Chegongmiao Industry area Futian district Shenzhen China 86 755 23487618 ax 86 755 23485319 sales atcomemail com Contact Technical Support Tel 86 755 23481119 Website address http www atcom cn ATCOM Wiki Website http www openippbx org index php title Main_ Page Download Center http Avww atcom cn download html www atcom cn 2 A7 S ATCOM Chapter 1 the Introduction of AX 2G4A Overview of the AX 2G4A AX 2G4A Asterisk card is a hybrid card which support two GSM channels and 4 FXO FXS analog ports Using AX 2G4A open source Asterisk PBX and stand alone PC users can create their SOHO telephony solution which includes all the sophisticated features of traditional PBX and extended features in IP PBX such as voicemail call transfer call park call pick up call forward bulk SMS sending SMS receiving and so on Features Two GSM channels and four analog ports Bulk SMS sending SMS receiving and storage Multi language for SMS content IMEI changeable PIN Number unlock for the SIM card Hardware echo cancellation embedded on the GSM module Monitor GSM signal strength by command and LEDs Monitor communication status by command line Send SMS by Asterisk CLI and dial plan Detect accurately when the called party answers
11. feature will help customer to do billing accurately www atcom cn 14 ATCOM 4 Use the dmesg command to check your GX01 version root localhost dmesg wctdm init GSM CARD 0 VoiceGSM System 0a Module 0 Installed AUTO GSM version 0x46 wctdm init GSM CARD VoiceGSM System 0a Module 1 Installed AUTO GSM version 0x46 Notice only the GX01 0x41 and above version support bulk SMS sending multi language for SMS content and Pin number unlock only the GX01 0x46 and above version support SMS receiving 5 Input PIN Number for the SIM card in etc asterisk dahdi channels conf file add the following red line 33 line 2 WCTDM 6 1 FXSKS In use SWEC MG2 pinnum 1234 signalling fxs_ ks callerid asreceived group 0 context from pstn channel gt 2 After setting please restart asterisk to make the setting effective 6 Please use the following command to read your IMEI number of GX01 root localhost cat proc dahdi imei read 1 IMEI 355842020258444 IMEI 355842020187437 IMEI2 IMEI3 7 Please start asterisk then use the following command to change IMEI 1 stands for the channel number and 355842020257974 stands for the IMEI number which you want to use localhost CLI gt gsm set imei 1 355842020257974 gsm set imei cardnum 1 value 355842020257974 gsm set imei ok Edit a dial plan and use AX 2G4A to make outgoing calls and get incoming calls 8 Please edit a dial plan in extensions conf file you c
12. g simple switch on DAHDI 1 1 Jul 1 11 42 53 NOTICE 20678 chan_dahdi c 8734 ss thread Got event 18 Ring Begin Executing s from pstn 1 Answer DAHDI 1 1 in new stack Executing s from pstn 2 Dial DAHDI 1 1 sip 500 in new stack Using SIP RTP CoS mark 5 Called 500 SIP 500 00000004 is ringing SIP 500 00000004 answered DAHDI 1 1 11 Plugging PSTN line into the FXO ports customer can dial out via FXO ports Connecting analog phone to FXS ports customer can use analog phone to dial out via FXO ports or via GSM channels www atcom cn n W ATCOM Chapter 6 Sending and Receiving SMS There are two ways for users to send SMS by ATCOM AX 2G4A 1 Sending SMS by asterisk CLI command directly In the following example it sends a message to 13728737752 using the first channel localhost CLI gt sendsms dahdi 1 13728737752 Welcome to ATCOM Using SIP RTP CoS mark 5 Launching Sendsms dahdi 1 13728737752 Welcome to ATCOM on SIP 600 0000002c Launching DoSms 13728737752 Welcome to ATCOM on DAHDI 1 1 Apr 25 14 32 32 WARNING 22660 chan dahdi c 5827 dahdi handle event gsm send sms sucess Hungup DAHDI 1 1 2 Sending bulk SMS Before sending the SMS please start Asterisk In var spool asterisk directory please edit a xml file like the following format then copy the content to outgoing file after that the SMS will be send out bulksms xml lt xml version 1 0 encoding
13. ill be green steady LED22 Network status indicator of SIM card of the second channel When the SIM card is searching network the LED22 will blink fast when the SIM card has found the GSM network and registered successfully the LED22 will flip at lower frequency Button used for turning off the GX01 www atcom cn 6 ATCOM Chapter 3 Software Installation Test Environment dahdi linux 2 3 0 4 download from ATCOM website dahdi tools 2 3 0 4 asterisk 1 6 2 6 4 download from ATCOM website centos 5 6 kernel version 2 6 18 238 e15 AX 2G4A 2 GX01 1 AX210S 1 AX210X After inserting the card into your PCI slot and boot your server please use the lspci command to check the PCI bus compatibility From the correct output you can see the following line A Tiger Jet device will be found if you can not see the Tiger Jet device please poweroff your server and try another PCI slot if it still does not help you have to check the compatibility issue between the card and your PCI bus 1 To install asterisk and dahdi we have to use yum command to install the following prerequisite packages bison bison devel zlib zlib devel openssl openssl devel gnutls devel gec gec c 2 Download dahdi linux dahdi tools and asterisk Attention please download dahdi linux and asterisk from ATCOM website because ATCOM has modified the source code for AX 2G4A root localhost src weet http www atcom cn cn download card
14. m 1 time 2011 09 09 16 08 31 send to called 13728731752 result 1 Hungup DAHDI 1 1 User can also check if the SMS is sent successfully or not by checking the var log asterisk sms sendsms directory the system will generate one log file each day for writing down if the SMS is sent successfully or not for example sendsms_2011 12 02 log is generated on Dec 02th 2011 which writes down all the sent SMS results on Dec 02th 2011 The Format of the xml file Xml file name customer can name whatever name you want Receiver add the destination phone number one line for one destination phone number the example above add two destination phone numbers Channel choose the GSM channel by which the system send the SMS out For one AX 2G4A it should be 1 or 2 Content input or paste the SMS content that you need to send out 3 Receiving SMS When one SMS is received the system will generate a file for storing the SMS and the file is under var log asterisk sms recvsms directory The format of the file name recvsms_ channel number time cell phone number log The format of SMS content channo channel gt gt date time cell phone number SMS content www atcom cn 18 Chapter 7 Reference http www asteriskguru com http www asterisk org downloads http www openippbx org index php title Main_Page http www atcom cn www atcom cn ATCOM
15. s ax4 asterisk 1 6 2 6 9 tar gz root localhost src weet http www atcom cn cn download cards ax4 dahdi linux 2 3 0 9 tar gz root localhost src l 3 Install dahdi linux and dahdi tools Install dahdi linux 1 root localhost src tar xvzf dahdi linux 2 3 0 4 tar gz 2 root localhost dahdi linux 2 3 0 make 3 root localhost dahdi linux 2 3 0 make install www atcom cn a _ gt l ATCOM Install dahdi tools 1 2 3 4 5 1 2 3 4 5 root localhost src tar xvzf dahdi tools 2 3 0 4 tar gz root localhost dahdi tools 2 3 0 configure root localhost dahdi tools 2 3 0 make root localhost dahdi tools 2 3 0 make install root localhost dahdi tools 2 3 0 make config Install asterisk root localhost src tar xvzf asterisk 1 6 2 6 4 tar gz root localhost asterisk 1 6 2 6 configure root localhost asterisk 1 6 2 6 make root localhost asterisk 1 6 2 6 make install root localhost asterisk 1 6 2 6 make samples www atcom cn Chapter 4 Software Configuration 1 Please check if the AX 2G4A driver has been loaded successfully run cat proc interrupts command and you should see one line with ax4g ax2 4a 20 2310670 2218516 JIO APIC fasteoi ax4g ax2 4a If you can not see ax4g ax2 4a you can try to poweroff your server and replug AX 2G4A into another PCI slot 2 Please run the dahdi genconf command to configure the etc dahdi system conf file and
16. wlstart Default Echo Canceler mg2 Slaves 05 Channel 06 FXO Kewlstart Default Echo Canceler mg2 Slaves 06 6 channels to configure Setting echocan for channel to mg2 Setting echocan for channel 2 to mg2 Setting echocan for channel 3 to mg2 Setting echocan for channel 4 to mg2 Setting echocan for channel 5 to mg2 Setting echocan for channel 6 to mg2 4 Please add the following line at the bottom of the chan_dahdi conf file include dahdi channels conf 5 Please run asterisk with the following command asterisk vvgc reload 6 Please run dahdi show channels command You should see 6 channels as the following localhost CLI gt dahdi show channels Chan Extension Context Language pseudo default from pstn 2 from pstn 3 from pstn 4 from pstn 5 from internal 6 from internal localhost CLI gt MOH Interpret default default default default default default default State In Service In Service In Service In Service In Service In Service In Service www atcom cn _ ATCOM If you need your GSM send or receive messages you can modify the following parameters 7 Please add the coding for sending message in the chan_dahdi conf file channels Default language slanguage en sms_language en For example you can add three language system weur using for western Europe eeur using for eastern Europe cn using for Chinese Modify the display language environment
Download Pdf Manuals
Related Search