User Manual - Multiform Lighting
Contents
1. AGC DMX connects sairone innri ee een eaten ee eeeeanees 3 pin XLR Male Female Modulation Type cc ceeeeeeeeeenteeeeeeeee eee ees Advanced Bit Angle Modulation ABAM Control eloo o MPP T DMX 512 1990 Dimensions without brackets ceeeeeeeeeeeeeee eee enaes W 266 x H 226 x D 110 mm Weight ciiir aeae a vias ves Raed E EE N E A dried 3 4 kg m Standards This product complies with the following standards RUES E E E E E E E EN 60065 2001 A1 es ENG e E A EN61204 3 2001 EU Harmonics cccccccccccccececeeeseeseececeeceeeeceaueaaesseeeeeeeeeeeseeaueaaeneeeees EN61000 3 2 2001 EU WFICK EPR i sakcciadedacasdduavenn Saaaawean danas a page wes saraw e G GE EN61000 3 3 1995 WS SAlCLY isinna coena See ase cee MAdmevlons sowansed aba shdencnay ataa pai aa ease UL60065 WS TEMG aa aissacaitenwats san ntaanmted aauahean E Ea FCC Part 15 This product meets both the EMC Directive 2004 108 EC and the Low Voltage Directive 2006 95 EC V1 00 03 2009 Multiform Leigh on Sea UK 15 WV MULTIFORM User Manual LS1018 Dmx controlled RGB HP Indoor Wash Maintenance Boot loader The Maintenance boot loader function enables the unit to receive firmware updates via the DMX connectors For further information refer to our website and check Download Switch on condition The unit always returns to the last mode before it was switched off In DMX Slave SLA or DMX Mode d or DMX Preset Mode P2. Please note If the display is in OFF mode it will take approximately 25 seconds before the display switches off It will be switched on again if any key is touched and will switch off again after 25 seconds if the keys are not unlocked by the procedure mentioned above Termination To avoid interference the last unit of a DMX chain should be terminated Therefore the DIP switch 9 of the last unit in the DMX chain must be switched ON V1 00 03 2009 Multiform Leigh on Sea UK 13 User Manual LS1018 Dmx controlled RGB HP Indoor Wash WW MULTIFORM P DMX Preset Mode If you want to run the pre programmed patterns and scenes by an external DMX controller you can use the DMX Preset Mode Press the MODE button 5 until the display shows P indicating operation in P DMX Preset mode Set the DMX starting address by simply using the UP DOWN buttons 6 7 The chosen DMX address comes effective approximately 3 seconds later and will show up on the display 2 in alternation to the P The unit receives DMX values on a packet of four channels and mirrors the received data on the DMX output 13 If a DMX signal is present the DMX LED 3 will turn on The four channels control the unit as follows If DMX value of channel 3 is lower than 50 the unit works with static colours DMX Channel Value Range Function CH1 000 255 Output mix choice from presets see C mode CH2 000 255 Master level
3. all DMX values are cleared if power is switched off DMX signal drop condition The device will retain the status that it was in before the DMX signal got lost but potential tact settings will be automatically cleared DMX channel assignment overview Mode gt A 03 P P D SLA DMX CH3 lt 50 CH3 gt 50 CH1 Out1 Out1 Mix Pattern Out1 Out1 CH2 Out2 Out2 Level Level Out2 Out2 CH3 Out3 Out3 0 49 Speed Out3 Out3 CH4 0 0 Tact Tact Level Tact 0 V1 00 03 2009 Multiform Leigh on Sea UK 14 User Manual LS1018 Dmx controlled RGB HP Indoor Wash gt gt WV MULTIFORM General advice 1 2 3 4 Read this manual completely before using the product Keep this manual in your records for future reference Follow all instruction printed in this manual otherwise warranty may be void Follow all printed security advice on the product itself The lighting flash with arrowhead within an equilateral triangle makes you aware of non insulated AC mains voltage inside the unit The exclamation mark within an equilateral triangle makes you aware of important operating and maintenance instructions in the literature attached to this product Take care of enough distance between this product and sources of hum and noise like electric motors and transformers Carry this product with greatest care Punches big forces and heavy vibration may damage this product mechanically The manufact
4. by an external DMX signal the DMX LED 3 is lit d Mode DMX Mode Press the MODE button 5 until the display shows d indicating operation in d DMX mode Shortly after that the display shows the DMX starting address You can choose any DMX starting address by simply using the UP DOWN buttons 6 7 The chosen DMX address comes effective approximately 3 seconds later and will show up on the display 2 in alternation to the d This allows control of the unit by any external DMX signal sending on the chosen channel In this mode the potentiometer 1 is disabled The unit receives DMX values on a packet of four channels and mirrors the received data on the DMX output 13 If a DMX signal is present the DMX LED 3 will turn on The four channels control the unit as follows DMX channel Value Range Function CH1 000 255 Out level CH2 000 255 Out2 level CH3 000 255 Out3 level CH4 000 127 Master level 128 227 Tact 128 slow 227 max speed 23 Hz 228 255 Master level full on Tact off Addressing has to be done as follows 001 first device CH 1 4 factory default 005 second device CH 5 8 009 third device CH 9 12 013 fourth device CH 13 16 and so on This setting is stored even if the device is switched off V1 00 03 2009 Multiform Leigh on Sea UK 11 User Manual LS1018 Dmx controlled RGB HP Indoor Wash WW MULTIFORM A16 Hard switch MixF M
5. cable 1 pcs operation manual Accessory parts 1 pcs Security lug If any part is missing please contact your dealer immediately for replacement V1 00 03 2009 Multiform Leigh on Sea UK 5 User Manual LS1018 Dmx controlled RGB HP Indoor Wash WW MULTIFORM m Getting started choosing a location Risk of fire The LS1018 Multibeam DMX controlled RGB High Power AAN Indoor LED Wash has been designed to work in dry indoor environments at environmental temperatures up to 35 degrees Celsius For proper operation the unit must be operated with unobstructed air convection to its outside metal case Operate the LS1018 MultiBeam DMX controlled RGB High Power Indoor LED Wash in environments with more than 35 degrees environmental temperature or more than 75 relative humidity Operate the LS1018 MultiBeam DMxX controlled RGB High Power Indoor LED Wash in any closed environment smaller than 10cbm unless forced air convection is provided m Getting started secure mounting The LS1018 Multibeam DMX controlled RGB High Power Indoor LED Wash can be mounted in various ways Floor standing operation e Turn the bracket to the lower side of the unit and fold out the second inlaying bracket e Place the unit in a secure position where it can neither be touched by anyone or could possibly become an objective for anyone to stumble e Use the provided cable fixing slots in the bracket to fix any cables using a strap e Make sure to
6. comply with cooling requirements of the used power supply if any Hanging Rigging ceiling mounted operation Risk of injury Overhead mounting requires extensive experience including among others calculating working load limits good knowledge of the installation material being used and periodic safety inspection of all installation material and the unit If you lack such qualifications do not attempt the installation yourself Improper installation can result in body injury Be sure to complete all rigging and installation procedures before applying power to the unit e Leave the inner and outer bracket folded e The unit should be installed out of reach of people and outside areas where persons may walk by or be seated V1 00 03 2009 Multiform Leigh on Sea UK 6 User Manual LS1018 Dmx controlled RGB HP Indoor Wash WW MULTIFORM SLA DMX Slave Mode Press the MODE button 5 until the display shows SLA indicating operation in SLA SLAVE mode In this mode the unit is set to DMX channel 001 in order to receive the signals from a master unit of the Multiform LS series being in mode A or C The unit interprets CH1 as Out1 level CH2 as Out2 level and CH3 as Out3 level CH4 is not in use and the potentiometer 1 is disabled This mode can also be used for remotely controlling the unit if no specific DMX address is needed and channels 001 003 can serve as a default To indicate that the unit is controlled
7. spare parts Consequently take care of your dealer or maintenance company to be authorized by the manufacturer a Health advice This unit produces and absorbs electromagnetic radiation The strength of radiation and the sensitivity for disturbing interference matches the CE and FCC requirements A corresponding sign is printed on the backside of the unit Any change or modification may affect the behavior of the unit concerning electromagnetic radiation with the CE requirements eventually not to be met any more The manufacturer takes no responsibility in this case Functional advice This unit is immune to the presence of electromagnetic disturbances both conducted and radiated up to a certain level Under peak conditions the unit is classified to show a class C performance criteria and may encounter temporary degradation or loss of function which may need manual help to recover In such case disconnect the AC power from the unit and reconnect it again to recover a Environmental advice This unit is build to conform to the ROHS standards and the WEEE directive 2002 96 EC of the European Parliament and of the Council of the European Union Under these regulations the product shall not be discarded into regular garbage at the end of its life but shall be returned to authorized recycling stations LA m Unpacking Please check that the box contains the following items Main parts 1 pcs LS1018 main unit 1 pcs mains
8. to very fast value 255 If channel 4 reaches a DMX value of 50 or above a tact function will be added to the chases The tact speed can be adjusted from slow value 50 to 23 pulses per second value 255 Note Whether the unit works in static mix mode or pattern mode only depends on the value of channel 3 So make sure the value of channel 3 is lower than 50 to be in static mix mode Otherwise you will be in pattern mode In this mode the potentiometer 1 is disabled Addressing has to be done as follows 001 first device CH 1 4 factory default 005 second device CH 5 8 009 third device CH 9 12 013 fourth device CH 13 16 and so on This setting is stored even if the device is switched off Display on off If you wish the display to be lit only when a change in operation is made the DIP switch 10 should be in the position off Now if any of the buttons is not pressed for more than approximately 25 seconds the display is switched off As soon as one of the buttons is pressed again the display switches on immediately In this case the first touch of the button is ignored in respect to the normal function of that button Key lock Pressing the MODE button 5 for longer than 3 seconds locks all the buttons 5 7 and the potentiometer 1 The display shows LOC in alteration to the mode changing every 2 seconds Pressing the MODE button again for more than 3 seconds unlocks the button and potentiometer functions
9. 1 00 03 2009 Multiform Leigh on Sea UK 3 User Manual LS1018 Dmx controlled RGB HP Indoor Wash damage by foot steps or by squeezing it Take especially care of the AC cord outlet on the unit as well as the AC plug and wall outlet at the other end of the cable Do not open the unit for service purpose as there are no user serviceable parts inside Warranty will be void in any case of unauthorized service by the user or other not authorized persons Take care of not placing the unit near sources of heat e g Protection from fire 1 AAN powerful amplifiers fog machines 2 3 Allow at least about 6 15cm between this unit and other devices or a wall to allow for proper cooling Be sure this fixture is kept at least 0 5m away from any flammable materials decoration etc Do not stick filters masks or other materials directly on the LEDs or the LED cover screen Take always care of sufficient air convection in the uni s environment to avoid overheating especially when mounting in a closed environment Make sure air convection slots are not blocked Do not operate this unit in environmental temperatures exceeding 35 degrees Celsius Check the total maximum power of your AC wall outlet if you connect several units to one wall outlet and avoid any overloading Never use any accessories or modifications not authorized by the manufacturer of this unit Protection from injury and damage l 1 2 7 V
10. 1 00 03 2009 Multiform Leigh on Sea UK 4 Choose a location for operation where the unit is protected from vibration and where a fixed mounting position is provided In case of overhead mounting follow appropriate rigging rules and your country s regulations for rigging safety See appendixes if any Before plugging the AC cord in the wall outlet check whether the AC mains voltage and frequency is the same as this product is specified for Whenever your AC plug should not match the wall outlet contact you dealer immediately If fluids have spilled into the unit or small parts have intruded the unit immediately switch off the unit and hand it over to the authorized service for a security check Disconnect the unit from AC supply by pulling the AC plug out of the wall outlet or the units AC socket during a thunder storm in order to avoid any damage on the unit due to AC voltage peaks In cause of not correct function of this unit or damaged AC cord or other damaged parts pull immediately the AC plug out of the wall outlet and hand the unit over to the authorized service for a security check To meet all aspects of functionality and security during mainte AAN MULTIFORM AAN MULTIFORM User Manual LS1018 DMX controlled RGB HP Indoor Wash The pre programmed soft fade or hard switching patterns can be chosen by means of CH1 whilst CH2 is used as a level channel CH3 allows to set the fade time or pattern speed from slow value 50
11. CH3 000 049 Static mix mode active CH4 000 049 Tact off 050 255 Tact 050 slow 255 max speed 23 Hz Output mix presets can be activated by means of CH1 whilst the chosen mix can be adjusted with CH2 If the value of CH4 is above 50 the unit is set to tact mode The tact speed for any fixed output mix chosen on the first channel can be adjusted from zero value lt 50 to 23 cycles per second value 255 If DMX value of channel 3 is equal or higher than 50 the unit works in pattern mode CH1 Pattern CH1 Pattern 000 015 Soft fade Out1 Out2 136 150 Hard switch Out2 Out3 016 030 Soft fade Out2 Out3 151 165 Hard switch Out1 Out3 031 045 Soft fade Out1 Out3 166 180 Hard switch Out1 MixA 046 060 Soft fade Out1 MixA 181 195 Hard switch MixB MixC 061 075 Soft fade MixB MixC 196 210 Hard switch MixD MixE 076 090 Soft fade MixD MixE 211 225 Hard switch MixF MixG 091 105 Soft fade MixF MixG 226 240 Hard switch Out1 Out2 Out3 106 120 Soft fade Out1 Out2 Out3 241 255 Hard switch Out1 MixA Out2 121 135 Hard switch Out1 Out2 MixB Out3 MixC DMX Value range Function CH2 000 255 Level CH3 050 255 Chase speed CH4 000 049 Tact off 050 255 Tact 050 slow 255 max speed 23 Hz V1 00 03 2009 Multiform Leigh on Sea UK 12 User Manual LS1018 Dmx controlled RGB HP Indoor Wash WW MULTIFORM nance work to be preformed on this unit all parts should be replaced by genuine
12. User Manual LS1018 Dmx controlled RGB HP Indoor Wash WW MULTIFORM m APPENDIXES A Safety rules for overhead rigging USER MANUAL Risk of injury Overhead mounting requires extensive experience including among others calculating working load limits good knowledge A N of the installation material being used and periodic safety inspection of LS1 018 MultiBeam all installation material and the unit If you lack such qualifications do DMX controlled RGB High Power Indoor LED Wash not attempt the installation yourself Improper installation can result in body injury Be sure to complete all rigging and installation procedures before applying power to the unit ENGLISH Page 2 16 e The unit should be installed out of reach of people and outside areas where persons may walk by or be seated e Make sure that the installation area can hold a minimum point load of 10 times the device s weight e In fixed installations fix the unit with self locking screws nuts to the mounting point e When mounting the unit to truss be sure to secure an appropriately rated clamp to the hanging yoke using a M10 screw fitted through the center hole of the hanging yoke e Always use a certified safety cable that can hold 12 times the weight of the device when installing the unit This secondary safety attachment should be installed in a way that no part of the installation can drop more than 20cm if the main attachment fails e Never stand directly below
13. ctly below the device when mounting removing or servicing the fixture Make sure the area below the installation place is free from unwanted persons during rigging de rigging and servicing e The operator has to make sure that the safety relating and machine technical installations are approved by an expert before using them for the first time The installations should be inspected every year by a skilled person to be sure that safety is still granted e Use the provided cable fixing slots in the bracket to fix any cables using a strap e Make sure to comply with cooling requirements of the used power supply if any V1 00 03 2009 Multiform Leigh on Sea UK 7 User Manual LS1018 Dmx controlled RGB HP Indoor Wash WW MULTIFORM m Operation User interface overview 1 In A Mode Speed Control except A1 Mix Control In C Mode Level Control 2 Display showing the Mode DMX address LOC function etc 3 Indicates presence of a DMX signal 4 Indicates the sound activated mode internal microphone 5 MODE selection button 6 UP button 7 DOWN button 8 Internal microphone 9 Switches on the termination for the last unit in the DMX chain 10 Switching the display on or off with delay 11 Maintenance not in use 12 Power Input 90 250V AC 13 DMX Output connector 14 DMxX Input connector V1 00 03 2009 Multiform Leigh on Sea UK 8 User Manual LS1018 Dmx controlled RGB HP Indoor Wash WW MULTIFORM Upon the user s choice the un
14. e Mode SLA If you leave mode A for any reason and come back later into mode A the unit will recall the last chosen pattern even if the unit was switched off in between Pattern list Description Function of Knob 1 AO All off None A1 Static scene Mix A2 Soft fade Out1 Out2 Speed A3 Soft fade Out2 Out3 Speed A4 Soft fade Out1 Out3 Speed A5 Soft fade Out1 MixA Speed A6 Soft fade MixB MixC Speed A7 Soft fade MixD MixE Speed A8 Soft fade MixF MixG Speed A9 Soft fade Out1 Out2 Out3 RGB Speed A10 Hard switch Out1 Out2 Sound activation Speed A11 Hard switch Out2 Out3 Sound activation Speed A12 Hard switch Out1 Out3 Sound activation Speed A13 Hard switch Out1 MixA Sound activation Speed A14 Hard switch MixB MixC Sound activation Speed A15 Hard switch MixD MixE Sound activation Speed V1 00 03 2009 Multiform Leigh on Sea UK
15. it can work stand alone or may be controlled by external DMxX controllers Available modes A Auto Mode Press the MODE button 5 until the first digit on the display shows A indicating operation in A AUTO mode Then choose your desired pattern by using the UP DOWN buttons 6 7 see list below Changing the setting becomes effective 1 second after the new setting is made to allow stepping through presets without previewing all intermediate presets NOTE The A Mode is automatically disabled and can not be chosen when an external DMX signal is received DMX indicator LED 3 is lit Whilst being in pattern A 1 static scene turning knob 1 determines the mix whereas being in one of the other 26 patterns knob 1 controls the speed or selects the sound activated function refer to below pattern list The sound activated function can be activated by setting the knob 1 inside the first 10 degrees of its travel from left detent and it works from a built in microphone 8 which picks up the environmental sound Its activity is shown by the flashing of the right dot 4 in the display The level for all patterns is maximum In A mode the unit does not receive any values from the DMX input but generates related DMX values on the output according to the selected pattern so that other similar units from the Multiform LS series can show the same pattern if they are connected by DMX signal cables and set to Slav
16. ixG Sound activation Speed A17 Hard switch Out1 Out2 Out3 Sound activation Speed A18 Hard switch Out1 MixA Out2 MixB Out3 MixC Sound activation Speed A19 Random speed Out1 MixA None A20 Random speed Out2 Out3 None A21 Random speed Out1 Out3 None A22 Random speed Out1 Out2 Out3 None A23 All outputs tacted Sound activation Speed A24 Out1 tacted Sound activation Speed A25 Out2 tacted Sound activation Speed A26 Out3 tacted Sound activation Speed A27 Out1 Out2 Out3 chaser tacted Sound activation Speed C Colour Mode Press the MODE button 5 until the first digit on the display shows C indicating operation in C mode Then choose by using the UP DOWN buttons 6 7 one of the 19 presets as shown in the list below Changing the setting becomes effective directly Knob 1 determines the output level In C mode the unit does not receive any values from the DMX input but generates related DMX values on the output according to the selected pattern so that other similar units from the Multiform LS series can show the same behaviour if they are connected by DMX signal cables and set to Slave Mode SLA NOTE The C Mode is automatically disabled and can not be chosen when an external DMX signal is received DMX indicator LED 3 is lit If you leave mode C for any reason and come back later into mode C the unit will recal
17. l the last chosen mix even if the unit was switched off in between Available colour presets CO alloff C10 MixG C1 Out1 C11 MixH C2 Out2 C12 Mixl C3 Out3 C13 MixJ C4 MixA C14 MixK C5 MixB C15 MixL C6 MixC C16 MixM C7 MixD C17 MixN c8 MixE C18 MixO CQ MixF C19 All outputs full on V1 00 03 2009 Multiform Leigh on Sea UK 10 User Manual LS1018 Dmx controlled RGB HP Indoor Wash WW MULTIFORM e Make sure that the installation area can hold a minimum point load of 10 times the device s weight e In fixed installations fix the unit with self locking screws nuts to the mounting point e When mounting the unit to truss be sure to secure an appropriately rated clamp to the hanging yoke using a M10 screw fitted through the center hole of the hanging yoke e Attach the supplied M6 safety lug to the rear side thread insert rigging point and secure the installation with an appropriate safety cable fixed to an individual separate mounting point Be sure to only use the designated rigging point for the safety cable never secure a safety cable to any other point like a carrying handle etc e Always use a certified safety cable that can hold 12 times the weight of the device when installing the unit This secondary safety attachment should be installed in a way that no part of the installation can drop more than 20cm if the main attachment fails e Never stand dire
18. r light source with medium to flood angle from wall washing to theatre lighting m Security advice before use Warning Read this section carefully before installing powering AN operating cleaning or servicing this product The following symbols are used to identify important safety information in this manual DANGER WARNING WARNING WARNING Safety hazard Risk Hazardous voltage Fire hazard Read manual before of injury or death Risk of severe or installation and fatal electric shock operation V1 00 03 2009 Multiform Leigh on Sea UK 2 User Manual LS1018 DMX controlled RGB HP Indoor Wash WW MULTIFORM a Maintenance This unit does not need regular maintenance The internal circuit is protected by a 250V 2A slow blow fuse 5x20mm fuse If this fuse fails this usually indicates an internal fault requiring servicing by a qualified engineer The fuse shall only be replaced by a fuse of same specification and the replacement has to be made by qualified personnel obeying applicable safety rules a Technical data LS1018 MultiBeam DMX controlled RGB HP Indoor LED Wash LED peiit en 18pcs 3W RGB MulTriCell 1W R 1W G 1W B 56W Mains INp te iniia a E a AIEE aS AC90 250V 50 60Hz Power Supply fy PO visctscece ses aici eaea iaa pa a deeida switch mode POWEr Cons mptlO sisirin aasid eaaa E i naaeanend max 60W AA EEEE E EE 250V 2A T slow blow 5x20mm glass Sound control internal microphone with Automatic Gain Control
19. the device when mounting removing or servicing the fixture Make sure the area below the installation place is free from unwanted persons during rigging de rigging and servicing e The operator has to make sure that the safety relating and machine technical installations are approved by an expert before using them for the first time The installations should be inspected every year by a skilled person to be sure that safety is still granted AAN MULTIFORM V1 00 03 2009 Multiform Leigh on Sea UK 16 RevA 01 2009 Order code 12 010 0293 80100 1 01 User Manual LS1018 Dmx controlled RGB HP Indoor Wash WW MULTIFORM m Introduction Dear customer congratulations on the purchase of a Multiform branded item and the trust having been put in us with this decision Multiform is one of the leading global manufacturers of professional equipment and has decades of experience in design production and quality assurance To meet your requirements this unit has been designed and built to the highest standards so that we can assure you that you have made a good and satisfying investment To take full advantage of all possibilities and for your own safety and the safety of your environment please read these operating instructions carefully before you start using the unit m Product description The LS1018 MultiBeam DMX controlled RGB High Power Indoor LED Wash is a fixture designed for any purpose which requires a high power color mixing indoo
20. urer takes no responsibility for injury or damage caused by not following the safety precautions and instructions printed in this manual Warning Class 1M LED product 1 2 3 Do not look into the beam from a distance of less than 40 cm 16 inches Do not stare into the beam for extended periods at a short distance Do not view the beam directly with optical instruments such as magnifiers Protection from electric shock 1 2 7 Do not connect the AC power plug to the unit before assembly has been completed Only connect this unit to a mains socket outlet with protective earth connection ground fault earth fault protection and overload protection Where the mains plug or an appliance coupler is used as a dis connect device the disconnect device shall remain readily operable To pull the AC Cord out of the wall outlet or the unit s AC socket never pull the cable itself but only the AC plug Disconnect the unit from AC supply by pulling the AC plug out of the wall outlet or the units AC socket before any kind of cleaning on the product Use smooth and dry cloth only for cleaning Check all connection cables before reconnecting the unit Do not expose this unit to any dripping or splashing liquids and do not place objects filled with liquids such as vases on the unit Do not operate this unit near to open water or in high humidity Choose the position of the AC cord according to the lowest risk of V
Download Pdf Manuals
Related Search