FXM User Manual, Ver 1.0.1
Contents
1. The Zaptel driver must be installed for compilation and operation of this driver This driver supports the version of zaptel 1 4 So we recommend zaptel1 1 4 8 and Asterisk 1 4 17 for your use which can be downloaded from the website www synway net or http downloads digium com pub 2 3 Driver Installation Notes 1 Here we take the driver installation for FXM 8A PCI as an example 2 The driver installation for other board models in the FXM series is just the same way as that for FXM 8A PCI Only thing you should do otherwise is use the name of corresponding driver package to replace the name fxm8apci 1 0 0 tar gz 3 As Zaptel driver and Asterisk platform we use zaptel 1 4 8 MI Asterisk 1 4 17 See below for driver installation procedures Step 1 Login to the system users with root access only Step 2 Compile and install Zaptel Copy the file zaptel 1 4 8 tar gz to the target directory opt and execute the following commands to perform compilation of the Zaptel driver cd opt tar xvf zaptel 1 4 8 tar gz cd zaptel 1 4 8 make make install Copy fxm8apci 1 0 0 tar gz to the directory of zaptel 1 4 8 and execute the following commands cd opt zaptel 1 4 8 tar xvf fxm8apci 1 0 0 tar gz cd fxm8apci 1 0 0 Synway FXM Series User Manual Page 12 e2 Gynway Synway Information Engineering Co Ltd Step 3 Step 4 Step 5 make Complete the driver compilation for the2. All board models in the FXM series are listed in the table below FXM 8A PCI PCI X Support FXM 16A PCle PCI E Support Table 2 1 Board Models in FXM All CODECs supported by the FXM boards for voice playback and recording are shown as follows ss Fxmeapcl v vv vf EE EIER m rxmteacle v vi viv i Legend COD Coder DEC Decoder Vy Hardware based Unsupported Figure 2 2 FXM Supported CODEC That how many channels are supported by the FXM board is decided by hardware The following table shows the detail information Figure 2 3 FXM Supported Channels Synway FXM Series User Manual Page 3 e Gynway Synway Information Engineering Co Ltd 2 2 2 Hardware Structure amp Board Features 2 2 2 1 FXM 8A PCI Board and Its Features l Module Slot1 Ch1 Ch2 j N l l Module Slot2 Ch3 Ch4 I Ji L I Module Slot3 Ch5 Ch6 l Ji t i Module Slot4 Ch7 Ch8 I l j L P amp R Ringing Current amp Battery Feed Power Supply Jack Ch1 Ch8 Jacks corresponding to Channel 1 Channel 8 Figure 2 1 FXM 8A PCI Left and Front Views Note As shown in Figure 2 1 above the numbers for led jacks from left to right are 1 4 on the top and 5 8 at the bottom A light on means the corresponding channel is installed with a module in contrast a light off indicates no module is installed on the corresponding channel Figur
3. Synway FXM Series FXM 8A PCI FXM 16A PCle User Manual Version 1 0 Synway Information Engineering Co Ltd www synway net e2 Gynnway Synway Information Engineering Co Ltd Contents COMENS oE E E E E E E E E EEEREN i eleVielude IT EICH el ji SEA EECH EEN ch eegene iii Revision History EE iv PICE EE V Chapter Re UHT 1 1 1 What is AStOMS EE 1 Chapter 2 Board Installation cccccceceeeeeeeeeeeeeeeeeneeeneeeneeneseneeanseeseaeseaecaasceeseseansogssonssenesenees 3 Ak Atenon CEET 3 ZZ QUIGOING NSPECIO EE 3 2 2 1 Board Classification EE 3 2 2 2 Hardware Structure amp Board Features 4 2 2 2 1 FXM 8A PCI Board and Its teatures ccc ccccecececececccceccecececeueeeucereneaeaeeveneneneanerars 4 2 2 2 2 FXM 16A PCle Board and lts teatiures 6 2 3 Module Identification cc ccc ccccccccccccececccceccaceccacucecccceseaeuceuaeeneccsueuaceneccsueaeseeceaueueaneneas T 2 4 Interface Identification cc ccc cece cece cc cececcceccacececcccecucceceacaceneaucueaesueaecceneacsueauseeceseeneaneneas 7 SS Gs PRT EEN 7 PR e EE 8 RO NOR OT le UE 8 2 6 Hardware Installabon nerne 9 2 7 Software Installation c ccc ccc cccecccccccccccececccececcecuacaceauaccueacsueceacenegeeneacsueauseeeaesneansneas 11 2l Vtem FRC OU CII EE 11 2 07 2 Installation Package 00aaaanaanaannnnannnnnnnnnnnnnnnrnnnnnnnnnnrnnrnnnnnnnrnnrnnnnrnnrnnrnnrnnrnnnnrnnrnnne 11 2 7 3 Driver Installation 2 0 2 cece ccc
4. extension phone for the PBX supporting delivery of the calling party information in FSK DTMF to the phone It uses 40V battery feed voltage and the integrated overcurrent overvoltage circuit protection system can accommodate a subscriber line in length of up to 5 5km Refer to Figure 4 3 and Figure 4 4 for hardware structure Figure 4 3 Front View User Model Ver xx Version XXXXXX Date Figure 4 4 Rear View Synway FXM Series User Manual Page 17 Synway Synway Information Engineering Co Ltd Appendix A Technical Specifications of FXM 8A PCI Dimensions 170 x115mm excluding L bracket Weight 120g Excluding modules and external power supply Environment Operating temperature 0 C 55 C Storage temperature 20 C 85 C Humidity 8 90 non condensing Storage humidity 8 90 non condensing Input output Interface Ringing current amp battery feed power supply jack One 4 pin MPC 4 Telephone line jack Four 4 pin RJ11 Audio Specifications CODEC CCITT A u Law 64kbps Distortion lt 3 Frequency response 300 3400Hz 3dB Signal to noise ratio 238dB Echo suppression 240dB Maximum System Capacity Synway FXM Series User Manual Up to 10 boards concurrently per system up to 8 channels per board Power Requirements 5V DC 600mA 12V DC 80mA 12V DC 300mA Maximum power consumption lt 12W PC power only Impedance Input impedance 21MQO S500V DC 210kQ 1000Hz AC Ins
5. FXM 8A PCI board Compile and install Asterisk Copy the file Asterisk 1 4 17 tar gz from the CD to the target directory of opt or some other directory cd opt tar xvf Asterisk 1 4 17 tar gz cd Asterisk 1 4 17 configure make make install Complete Asterisk compilation Load the driver cd opt cd zaptel 1 4 8 modprobe zaptel cd fxm8apci 1 0 0 insmod shfxm 8a ko Start Asterisk Make sure all previous configurations are correct See Chapter 3 for details ztcfg vv asterisk vvvvc CLI gt zap show channels 2 4 Driver Uninstallation Step 1 Step 2 Uninstall the driver of the FXM 8A board Execute the Command rmmod shfxm 8a Check if the driver uninstallation is successful Execute the Command Ismod Check if the driver has been successfully uninstalled If successful the item shfxm 8a will not be shown in the result Synway FXM Series User Manual Page 13 e2 Gynway Synway Information Engineering Co Ltd Chapter 3 Configuration This chapter cites a simple configuration instance to explain how to configure Asterisk platform to meet individual application requirements Once getting familiar with this instance you are able to compile this configuration file for something you want 3 1 Common Configuration Items etc zaptel conf fxsks 1 4 Trunk Module fxoks 5 8 Station Module loadzone us defaultzone us etc asterisk zapata conf channels context examp
6. cc ccc ccccccccecceccceccunentetunentencuntunensuneunenteneunennsntsntunsunsunensensans 12 21 4 Driver CIA Sil EE 13 Chapter 3 Configuration cccccccceeceeeeeeeeneceneceeceeeeneeeneeenseaseneseneceneceeseeseusoeesoeseneseneseasenesens 14 3 1 Common Configuration Iiems 14 3 2 COnfiguration TIestng e E a r E E Ea E 15 Chapter 4 FXO amp Egeter 17 Appendix A Technical Specifications of FXM 8A PCL ccccsecsecseeceeeseeeeeeeeeeeeenseeseeneeeeees 18 Appendix B Technical Specifications of FXM 16A PCle cccccceeeceeeeeeeeneseneeeeseeesenenenees 19 Appendix C Technnical SaleS Support ccccccesceeeceeeeseeeeceeeeeesseseceeeaseuseneeneseseeneeaeeuseesesneeas 20 Synway FXM Series User Manual Page e2 Gynway Synway Information Engineering Co Ltd Copyright Declaration This manual is provided by Synway Information Engineering Co Ltd hereinafter referred to as Synway as the support file for Synway FXM Series board driver software Both the software and this manual are copyrighted and protected by the laws of the People s Republic of China All rights reserved no part of this manual may be extracted modified copied reproduced or transmitted in any form or by any means electronic or mechanical without prior written permission from Synway By using this manual you agree to the following Software License Agreement Synway reserves the right to revise this manual without pri
7. connects with an independent module interface may be FXO or FXS Jacks 1 4 from top to bottom correspond to Modules 1 4 A single board of FXM 8A PCI can be equipped with up to 4 dual channel modules and supports 8 voice channels The pin layout of the 4 pin RJ11 jack is shown as follows Synway FXM Series User Manual Page 7 e2 Gynway Synway Information Engineering Co Ltd Table 2 4 RJ11 2 4 2 RJ45 Each FXM 16A PCle board has 4 RJ45 jacks on the bracket A single board of FXM 16A PCle can be equipped with up to 8 dual channel modules and supports 16 voice channels The pin layout of the 8 pin RJ45 jack is shown as follows T a GE LP Fe A k Table 2 5 RJ45 2 5 Slot Compatibility Make sure it compatible with PCI slots when using an FXM board Users may choose whichever suitable according to the slot patterns illustrated in Figure 2 5 below Synway FXM Series User Manual Page 8 e2 Gynway Synway Information Engineering Co Ltd Slots 0 ee FER 1 ee eee Ce eee 3 M ee 1 WO WM Figure 2 5 Board with PCI Slot Slot Number 0 AGP Pro Slot 1 64 bit 5 0V PCI Slot 2 64 bit 3 3V PCI Slot 3 32 bit 5 0V PCI Slot 4 PCI E Slot The FXM 8A PCI board includes PCI 2 2 bus with burst data transmission rate up to 132 MB s supports the PNP plug and play feature which eliminates the need for jumper leads uses the general PCI design which supports the s
8. other Unix platforms The name Asterisk is derived from the all inclusive wildcard symbol in UNIX as well as Linux a symbol that stands for one or more unspecified characters used especially in searching text and in selecting multiple files or directories It implies the wide applicability of this software Asterisk provides a lot of functionalities which were supported only by expensive and proprietary Synway FXM Series User Manual Page 1 e2 Gynway Synway Information Engineering Co Ltd PBX before such as voicemail conferencing interactive voice response IVR and auto call transfer etc Since Asterisk is an open source PBX users can flexibly configure and extend this platform to have whatever functions needed even can write programs to develop some functional modules they want Therefore Asterisk is now increasingly used to take the place of traditional proprietary PBX Synway FXM Series User Manual Page 2 Gynway Synway Information Engineering Co Ltd Chapter 2 Board Installation 2 1 Attention on Unpacking When you unpack the board please check if it is damaged or corrupted during transportation In case of any loss take your bill of documents and contact the seller or dial the phone number listed in Appendix C to consult Note Only the trained and qualified service people are allowed to reinstall the board Users had better not do it by themselves 2 2 Outgoing Inspection 2 2 1 Board Classification
9. ates the board configuration Chapter 4 emphasizes the FXO and FXS modules Appendix A and Appendix B give the technical specifications of the boards Appendix C shows the contact way of technical support and sales department in Synway Although Synway has scrupulously checked through this manual but cannot guarantee the absence of errors and omissions We sincerely apologize for any consequent inconvenience brought to you and will be very grateful if you kindly give your advice regarding amendments to this book Synway FXM Series User Manual Page v e Gynway Synway Information Engineering Co Ltd Chapter1 Overview The driver for the Synway FXM series boards hereinafter referred to as FXM which is compatible and must be used with the Zaptel driver can smoothly and seamlessly support Asterisk system When using the FXM board to establish Asterisk platform all that you should do is configure and operate the Asterisk platform without secondary development by using FXM See Figure 1 1 below for the set up of the Asterisk application system with the FXM board xxx represents the existing and future board models in the FXM series Figure 1 1 FXM Driver Set up Figure 1 2 is a typical application model with FXM IP telephone Asterisk PBX Figure 1 2 Application Model 1 1 What is Asterisk Asterisk is the first Open Source PBX which is developed maintained and improved by Digium Inc It can run on Linux and
10. d the printed information after it successfully starts Asterisk should be something like the following CLI gt zap show channels Chan Extension Context Language MOH Interpret pseudo syn1 default 1 syn1 default 2 syn default 3 syn default 4 syn1 default 5 syn1 default 6 syn1 default T syn1 default 8 syn1 default If zaptel conf is improperly configured the system will prompt that this command does not exist after you enter zap into the command line 8 Regarding the configurations of trunks SIP and etc go to the following websites to refer to Asterisk s description http www asteriskdocs org modules news http www voip info org wiki index php page Asterisk config files Synway FXM Series User Manual Page 16 e gt Gynway Synway Information Engineering Co Ltd Chapter 4 FXO amp FXS FXO Trunk Module This module is equipped with the lightning proof circuit that reaches the telecom standard and connects its corresponding channel directly to local lines from Central Office Terminal COT with abilities to detect line voltage diagnose line failure and judge the on hook off hook state of the station phone which is linked with it See Figure 4 1 and Figure 4 2 for hardware structure Figure 4 1 Front View Tru n M odel Ver xx Version XXXXXX Date Figure 4 2 Rear View FXS Station Module This module functions either as a station phone provided it links directly to a telephone or as an
11. e 2 2 FXM 8A PCI Rear View See below for characteristic features of FXM 8A PCI 1 PCI 2 2 Bus Support Includes PCI 2 2 bus with burst data transmission rate up to 132 MB s PNP plug and play feature eliminates the need for jumper leads General PCI design supports 3 3V 5V PCI slot and PCI X slot Synway FXM Series User Manual Page 4 e2 Gynway Synway Information Engineering Co Ltd 2 DMA Read and Write The use of PCl based DMA technique for data reading and writing helps minimize the cost of the host CPU 3 Compatible with Asterisk Entirely compatible with Asterisk at the hardware driver level with all source codes open 4 On board SIMM Slots Fit modules to board Contacts on both sides greatly improve connection and ease installation 5 Module Configurable 4 on board dual channel modules can be freely arranged in pairs or groups for various complex multi functional applications 6 RJ11 Jack The on board RJ11 jack can connect directly or via a proper 2 way hub with telephone lines making connection easy and malfunctions rare 7 External Ringing Current amp Battery Feed Power Supply Provides station modules with battery feed and enables the phones which are linked to station channels to ring 8 Echo Cancellation The self adaptive echo cancellation feature gives the board the capability of 128ms echo cancellation so as to effectively eliminate echoes under various conditions canceling out t
12. em em em pe pe rem em em em dl wm pm em pm em Figure 2 8 Plug Structure Step 4 Set up an application environment Connect phone lines with the port to an FXO module and the telephone with the port to an FXS module to establish an application environment Step 5 Boot your computer and install the driver Regarding driver installation refer to Section 2 7 for details 2 Software Installation 2 1 System Requirements Host System Requirements CPU 300MHz Intel Pentium lll or above Memory 256M or more HD Depends on individual requirements Supported Operating Systems v Linus RH7 2 RH9 0 AS4 FC4 SUSE10 2 2 Installation Package The driver installation package includes all necessary files for installation and use of the Synway FXM driver See below for details Synway FXM Series User Manual Page 11 e2 Gynnway Synway Information Engineering Co Ltd fxmXXX 1 0 0 tar gz FXM driver package AST FXM_UserManual doc User manual for this driver English version 3 AsteriskTEOT zi Introduction to installation and configuration of Asterisk official provision Notes 1 fxmXXX marked in fxmXXX 1 0 0 tar gz varies on actual board models For example the driver package of FXM 8A PCI is called fxm8apci 1 0 0 tar gz while that of FXM 16A PCle is named fxm16apcie 1 0 0 tar gz fxmXXX 1 0 0 tar gz can only be installed with the help of the Zaptel driver and started by running Asterisk
13. ewlstart Default nnel 03 FXS Kewlstart Default nnel 04 FXS Kewlstart Default nnel 05 FXO Kewlstart Default nnel 06 FXO Kewlstart Default nnel 07 FXO Kewlstart Default nnel 08 FXO Kewlstart Default Ter eT T D Ter D N D annels to configure S000 00 0 E Ch ed pee Ba ee er Changing signalling on channel 1 from Unused to FXS Kewlstart Changing signalling on channel 2 from Unused to FXS Kewlstart Changing signalling on channel 3 from Unused to FXS Kewlstart Changing signalling on channel A from Unused to FXS Kewlstart Changing signalling on channel 5 from Unused to FXO Kewlstart Changing signalling on channel 6 from Unused to FXO Kewlstart Synway FXM Series User Manual Page 15 e2 Gynway Synway Information Engineering Co Ltd Changing signalling on channel 7 from Unused to FXO Kewlstart Changing signalling on channel 8 from Unused to FXO Kewlstart If zaptel conf is improperly configured the printed information displayed after you enter the command ztcfg vv should be something like the following Notice Configuration file is etc zaptel conf line 5 Channel 5 already configured as FXS Kewlstart at line A line 5 Channel 6 already configured as FXS Kewlstart at line A line 5 Channel 7 already configured as FXS Kewlstart at line A line 5 Channel 8 already configured as FXS Kewlstart at line A 4 error s detected In Step 3 if zaptel conf is properly configure
14. he effect of voice playback on DIMF and busy tones detection avoiding self excited oscillation and howling and minimizing the possibility of registering wrong DIMF and busy tones in a conference call designed especially for VoIP application environments 9 Voice CODEC Support Supports the hardware based A law u law codecs The recorded voice files can be edited and played by audio tools such as Cooledit Synway FXM Series User Manual Page 5 e Gynnway Synway Information Engineering Co Ltd 2 2 2 2 FXM 16A PCle Board and Its Features A oaup SC C Figure 2 3 FXM 16A PCle Left and Front Views FXM 16A PCle ee Figure 2 4 FXM 16A PCle Rear View See below for characteristic features of FXM 16A PCle 1 PCI Express Bus Support Includes PCI Express 1 0a bus with the single way transmission rate up to 2 5Gb supports PCI Express X1 X2 X4 X8 X16 slots and DMA transfer 2 On board SIMM Slots Fit modules to board Contacts on both sides greatly improve connection and ease installation 3 Module Configurable 8 on board dual channel modules can be freely arranged in pairs or groups for various Synway FXM Series User Manual Page 6 e2 Gynway Synway Information Engineering Co Ltd complex multi functional applications such as call center and recording functions available on a single board 4 RJ45 Jack A single board has 4 8 pin RJ45 jacks each of which can be converted to 4 2 pin RJ11 jacks
15. letest usecallerid yes hidecallerid no callwaiting no threewaycalling yes transfer yes echocancel yes relaxdtmf yes group 2 signalling fxo_ks Station Module channel gt 5 channel gt 6 channel gt 7 channel gt 8 group 1 signalling fxs_ks Trunk Module channel gt 1 channel gt 2 channel gt 3 channel gt 4 letc asterisk extensions conf exampletest exten gt _300X 1 Dial zap EXTEN 50 exten gt _300X n playback hello world Synway FXM Series User Manual Page 14 Synway exten gt _300X n Hangup Synway Information Engineering Co Ltd This configuration is performed provided Channels 1 4 are trunks and Channels 5 8 serve as stations Users can modify the configuration by their own situation extensions conf only sets the rules of stat ion calls 3 2 Configuration Testing Step 1 Step 2 Step 3 Notes Enter the following command to configure the board ztcfg vv Enter the following command to connect Asterisk asterisk vvvvc Check the state of channel connection upon a successful start CLI gt zap show channels In Step 1 if zaptel conf is properly configured the printed information displayed after you enter the command ztcfg vv should be something like the following Zaptel Version 1 4 8 Echo Canceller MG2 Con figuration Channel map Cha Cha Cha Cha Cha Cha Cha Cha 8 ch nnel 01 FXS Kewlstart Default nnel 02 FXS K
16. lots numbered 1 2 and 3 in Figure 2 5 The FXM 16A PCle board includes PCI E 1 0a bus and supports PCI E X1 X2 X4 X8 X16 slots i e the slot numbered 4 in Figure 2 5 2 6 Hardware Installation Note Always turn off the power before installation Step 1 Plug the desired modules into the module slots on the board and fit the board into the PC chassis Fix the screws on the L bracket and then go to the next step Step 2 Connect to analog phone lines or telephones gt FXM 8A PCI A single board has four RJ11 jacks each of which connects to a 4 lead line that corresponds to 2 channels The two leads in the middle constitute a port and the outer two leads set up another See Table 2 4 above for the pin layout and the corresponding channel number Each RJ11 jack can be converted via a special 2 way hub or constructed by yourself to connect with 2 analog channels See Figure 2 6 below for the structure of the 2 way hub Synway FXM Series User Manual Page 9 e2 Gynway Synway Information Engineering Co Ltd Figure 2 6 2 way Hub See Table 2 6 for the correspondence between the on board channels the 4 pins in an RJ11 jack and the 2 interfaces of a 2 way hub 2 and 3 pins RJ11 A 7 1 and 4 pins Table 2 6 Correspondence between Channels Pins in RJ11 and Interfaces of 2 way Hub Note When connecting to an RJ11 jack you can use a special 2 way hub to convert it to two independent jacks If you want to construc
17. ncludes four subseries Synway FXM Use of modular structure and analog lines Use of analog lines equipped with much more on board Synway FXS channels than FXM Synway TEJ Use of digital trunks E1 T1 J1 Synway CDC CODEC board The Synway FXM series board is a perfect substitute for the 800 series analog voice cards such as AEX800 and TDM800P from Digium Inc Since the FXM board integrates the capability of echo cancellation when using it there is no need to purchase an extra module of VPMADT032 to enable echo cancellation from Digium Inc The Synway FXM driver program as a link between the board hardware and Asterisk is only used to set up the Asterisk platform but not applicable to secondary development Each board model in the Synway FXM series has its corresponding driver package which is elaborated in the following text This manual as the help file for hardware installation software installation and configuration of the Synway FXM series aims at those installation and maintenance technicians as well as the salesmen who are using the FXM boards to set up Asterisk application systems This document consists of the following chapters Chapter 1 introduces the Asterisk application model and scenario set up by the Synway FXM series boards and tells what is Asterisk Chapter 2 describes the on board modules and jacks as well as the slot compatibility and then tells how to install boards on PC by examples Chapter 3 elabor
18. o Encoding amp Decoding A Law 64kbps u Law 64kbps Sampling Rate 8kHz Safety Lightning resistance Level 4 Page 19 Synway Synway Information Engineering Co Ltd Appendix C Technical Sales Support Thank you for choosing Synway Please contact us should you have any inquiry regarding our products We shall do our best to help you However our technicians and salesmen are mainly responsible for maintaining our boards and providing relative technical support If there are problems about Asterisk please keep touch with Digium Inc for help Headquarters synway Information Engineering Co Ltd http www synway net 9F Synway D amp R Center No 3756 Nanhuan Road Binjiang District Hangzhou P R China 310053 Tel 86 571 88860561 Fax 86 571 88850923 Technical Support Tel 86 571 88864579 Mobile 86 13735549651 Email techsupport sanhuid com Email techsupport synway net MSN scycindy_sh hotmail com sales Department Tel 86 571 88860561 Tel 86 571 88864579 Fax 86 571 88850923 Email sales synway net Synway FXM Series User Manual Page 20
19. or note Please contact Synway for the latest version of this manual before placing an order Synway has made every effort to ensure the accuracy of this manual but does not guarantee the absence of errors Moreover Synway assumes no responsibility in obtaining permission and authorization of any third party patent copyright or product involved in relation to the use of this manual Note Asterisk and Digium mentioned in this book are registered trademarks of Digium Inc Synway FXM Series User Manual Page ii Synway Synway Information Engineering Co Ltd Software License Agreement Synway Information Engineering Co Ltd hereinafter referred to as Synway owns the copyright of this software and its accessories relative files and archives hereinafter referred to as this product Any company or person can download the corresponding driver software and other useful documents for free directly from our website after purchasing a board of Synway Synway FXM Series User Manual Page iii e2 Gynway Synway Information Engineering Co Ltd Revision History Version Date Comments Version 1 0 2008 7 Initial publication Note Only major revisions to this manual itself recorded herein Synway FXM Series User Manual Page iv e2 Gynnway Synway Information Engineering Co Ltd Preface Thank you for choosing the Synway AST series boards which are designed to fully support Asterisk platform This series i
20. t lines by yourself please follow Figure 2 1 to connect each channel with corresponding pins gt FXM 16A PCle A single board has four RJ45 jacks each of which can be converted via a special 4 way hub or constructed by yourself to connect with 4 analog channels See Figure 2 7 below for the structure of the 4 way hub Figure 2 7 4 way Hub See Table 2 7 for the correspondence between the on board channels the 8 pins in an RJ45 jack and the 4 interfaces of a 4 way hub 1 and 2 pins 3 and 4 pins 2 interface 5 and 6 pins 7 and 8 pins Table 2 7 Correspondence between Channels Pins in RJ45 and Interfaces of 4 way Hub Step 3 Connect to the ringing current amp battery feed power supply Note Skip this step if FXS station module is not used in the system Synway FXM Series User Manual Page 10 eo Gynway Synway Information Engineering Co Ltd If you are using the external ringing current amp battery feed power supply from Synway note that the plug has a peculiar design for the prevention of improper insertion and extraction The correct way is to hold the plug body not the locking ring or it cannot be fully inserted when inserting the plug home into the socket and to grasp the locking ring not the plug body or the conductor when pulling the plug out from the socket See Figure 2 8 below tor dL I I Metal Ring Locking Ring Plug 2 epee ee ree GE DEER E I movable Body
21. ulation resistance for PC isolation from telephone line 22MQ 500V DC Telephone line impedance Compliant with the national standard impedance for three component network Audio Encoding amp Decoding A Law 64kbps p Law 64kbps Sampling Rate 8kHz Safety Lightning resistance Level Page 18 Synway Synway Information Engineering Co Ltd Appendix B Technical Specifications of FXM 16A PCle Dimensions 280x111mm excluding L bracket Weight 200g Excluding modules and external power supply Environment Operating temperature 0 C 55 C Storage temperature 20 C 85 C Humidity 8 90 non condensing Storage humidity 8 90 non condensing Input output Interface Telephone line jack Four 8 pin RJ45 Ringing current amp battery feed power supply jack One 4 pin MPC 4 Audio Specifications CODEC CCITT A u Law 64kbps Distortion lt 3 Frequency response 300 3400HZz 3dB Signal to noise ratio 238dB Echo suppression 240dB Maximum System Capacity Synway FXM Series User Manual Up to 10 boards concurrently per system up to 16 channels per board Power Requirements 3 3V DC 3A 12V DC 0 5A Maximum power consumption lt 12W PC power only Impedance Input impedance 21MQ 500V DC 210kQ 1000Hz AC Insulation resistance for PC isolation from telephone line 22MQ 500V DC Telephone line impedance Compliant with the national standard impedance for three component network Audi
22. via a four way hub so as to connect with analog phone lines making connection easy and malfunctions rare 5 External Ringing Current amp Battery Feed Power Supply Provides station modules with battery feed and enables the phones which are linked to station channels to ring 6 Echo Cancellation The self adaptive echo cancellation feature gives the board the capability of 128ms echo cancellation so as to effectively eliminate echoes under various conditions canceling out the effect of voice playback on DTMF and busy tones detection avoiding self excited oscillation and howling and minimizing the possibility of registering wrong DTMF and busy tones in a conference call designed especially for VoIP application environments 7 Voice CODEC Support Supports the hardware based A law law codecs The recorded voice files can be edited and played by audio tools such as Cooledit 2 3 Module Identification An FXM series board can have either FXO or FXS modules only or be equipped with both FXO and FXS modules 2 4 Interface Identification It s quite important to recognize different kinds of interfaces as such information is necessary for configuration of Asterisk platform In real practice not all interfaces on the board are used at a same time When to use which interface depends on the installed modules and their particular positions on the board 2 4 1 RJ11 Each FXM 8A PCI board has 4 RJ11 jacks on the bracket and each jack
Download Pdf Manuals
Related Search