ioLogik R1200 Series QIG
Contents
1. MOXA ioLogik R1200 Series Quick Installation Guide Second Edition April 2014 Overview The ioLogik R1200 comes with 2 RS 485 serial ports which can be used in one of two ways 1 For backup or asset monitoring or 2 As an RS 485 repeater The ioLogik R1200 has the industry s first all in one design and provides Automatic Field Configuration via USB No technical background is needed and maintenance is easy since users can upload a device s configuration settings and firmware via USB without needing to take a PC to the field site Model Selection Package Checklist e 1 ioLogik R1200 series remote I O product e Documentation and software CD e Quick installation guide printed Specifications Serial IO 2 x RS 485 2W Data Data GND TS le terminal block Protection Power Input 24 VDC nominal 12 to 48 VDC Wiring TO cable max 14 AWG Operating Temperature Standard Models 10 to 75 C 14 to 167 F Wide Temperature Models 40 to 85 C 40 to 185 F P N 1802012002011 Ambient Relative 5 to 95 non condensing Humidity Altitude Up to 2000 m Note Please contact Moxa if you require products guaranteed to function properly at higher altitudes Certifications Warranty Period Details Because of the limited lifetime of power relay products that use this component are covered by a 2 year warranty arity Data Bits BO O Stop Bits Flow Control Baudrate Sensor Type JO Mode e Off o2. ode Duel Default Dual RS 485 mode un User define communication parameters Initial Default Initial RS 485 communication parameters Rep Initial Jumper Settings The models with DIO or AI channels require configuring the jumpers inside the enclosure Remove the screw located on the back panel and open the cover to configure the jumpers DI Mode DO Mode Voltage Mode Current Mode DIO mode configuration is shown to the right default DO Mode Analog mode configuration is shown to the right default Voltage Mode Mounting The ioLogik R1200 is designed with a vertical form factor and can be used with both DIN Rail and wall mounting applications When mounting on a rail release the bottom mounting kit install the ioLogik on the rail and then restore the bottom mounting kit to fix the ioLogik to the rail When using wall mounting release both the upper and bottom DIN Rail kits LED Indicators LED Color LED Action On iPower On PWR Green On Power Off System Ready Green Green Located Blinking Red System Boot up Error Blinking Blinking Green Green I O Wiring Digital Input Output Sink Type DI Dry Contact DI Wet Contact DO Sink Source Sink 5 a s o A 85s Sale Siale 86 A S F lo 12 916 Q Q WWE oF 4 _ 9 g 5 z2 a2 Gi 2 xo Power v 2 Power P
3. ower Power Analog Input Relay Output Form A Voltage Current 0 10V 4 20 mA o gt O olol l gt gt O O E O 7 Load Load k T Power System Configuration ioSearch Utility ioSearch is a search utility that helps users locate an ioLogik R1200 on the local network The utility can be found in the Document and Software CD gt Software gt ioSearch the latest version can be downloaded from Moxa s website Load Factory Default Settings There are three ways to restore the ioLogik R1200 to the factory default settings 1 Hold the RESET button for 5 seconds 2 Right click the specified ioLogik in the ioSearch utility and select Reset to Default 3 Select Load Factory Default from the web console Modbus Address Table Please refer to the user s manual for details of the ioLogik s Modbus address MOXA The Americas 1 714 528 6777 toll free 1 888 669 2872 Europe 49 89 3 70 03 99 0 www moxa com support Asia Pacific 886 2 8919 1230 China 86 21 5258 9955 toll free 800 820 5036 2014 Moxa Inc All Rights Reserved 6
4. pen DI to COM e Off O to 3 VDC solation Counter Frequency Digital Output O Mode DO or Pulse Output Width Frequency Protection Over current Protection 2 6 A 4 channels 650 mA Over temperature 175 C typical 150 C min Shutdown Current Rating 200 mA per channel solation 3K VDC or 2K Vrms Relay Output orm A N O relay outputs 5A F i Contact Rating 5 A 30 VDC 5A 250 VAC 5A 110 fone seine fine PRG AGERE 2A A Inductance Load 2A i 1G min 500 VDC Expected Life 100 000 times Typical Resistance 0 1 FSR 25 C 0 3 FSR 10 and 60 C 0 5 FSR 40 and 75 C Sampling Rate all 12 samples sec channels Input Impedance 10M ohms minimum Built in Resistor for 120 ohms Current Input 12 bits 0 to 10 VDC 4 to 20 mA 0 mA Max 0 1 FSR 25 C 0 3 FSR 40 and 75 C e Internal power 400 ohms e External 24V power 1000 ohms Installation Power and Networking Connect the 12 to 48 VDC power line to the ioLogik R1200 s terminal block V terminal connect the ground from the power supply to the V terminal Connect the ground pin 77 if earth ground is available Power Supply 24VDC Nominal 12 to 48VDC I NOTE For safety reasons the wires attached to the power should be at least 2 mm 12 gauge in diameter Switch Settings The R1200 series provides Dual Rep and Run Initial switch settings to set up the communication mode Repeater m
Download Pdf Manuals
Related Search