Instruction Manual - Test Products International
Contents
1. ipi 905 PHOTO CONTACT TACHOMETER Instruction Manual WARNING Read instructions before operating Be sure these instructions accompany the tool when passed from one user to a new or inex perienced user Rotating equipment can cause flying particles Wear Safety Goggles User and bystanders Flying particles can cause eye injury Keep yourself clothing and test equipment clear of moving parts Note To zero previous readings on all tach operations Press and hold the START button then press the desired function button If a stored value appears release START button until the display goes off Then press the START button immediately and a zero reading will be displayed until the unit is used for mea suring RPM or the START button is released PHOTO TACH OPERATION Measurement Procedure 1 Unscrew contact collar from optical end of 505 if attached 2 Attach a piece of reflectlive tape on the rotating object to be measured 3 Depress and hold the START button and then press the Photo button lower right on the 505 4 With the start button depressed point the optical end at the rotating surface so the relective tape passes the lens every rotation 5 Read the RPM on the LCD display Memory Recall Note The memory resets itself once the START button is depressed and stable measurements are displayed for 10 seconds or 12 revolutions whichever is longer The values are stored when2. 1 2 3 4 5 Screw the shaft assembly to the optical end of the 505 Insert the large wheel to the end of the shaft assembly Press and hold the START button and then press the ft min feet per minute or m min meters per minute on the 505 While pressing the START button hold the wheel against the moving surface Read the speed on the LCD Memory Recall Note The memory resets itself once the START button is depressed and stable measurements are displayed for 10 seconds or 12 revolutions whichever is longer The values are stored when the START button is released 1 2 When you are finished taking measurements release the START button Depress the MEMORY button once the LAST reading will be displayed Press the MEMORY button twice the MAX reading will be displayed Press the MEMORY button three times the MIN reading will be displayed Unit will power off after 5 seconds 5 BATTERY REPLACEMENT Measurement Procedure 1 Remove the screw holding the battery compart ment cover in place on the back of the 505 2 Slide the cover off of the unit 3 Remove the 2 each AA alkaline batteries and replace with the same type 4 Replace the cover and screw STANDARD ACCESSORIES Reflective Tape 2 0205 A501 Contact RPM Adapter screw on A502 RPM Adapter Cone Type A503 RPM Adapter Funnel Type A504 Surface Speed Test W
3. heel A505 0 D 48 7 mm exactly Carrying case uaaaa aaa iai 12 A915 OPERATION SPECIFICATIONS Function Range Accuracy Photo Tach 6 30 000 RPM 0 1 of FS 1 digit Contact Tach 6 20 000 RPM 0 1 of FS 1 digit Surface Speed 0 9 3 046 m min 0 1 of FS 1 digit 2 0 9 990 ft min 0 1 of FS 1 digit GENERAL SPECIFICATIONS Display 5 Digit LCD Operating Temperature 32 to 122 F 0 to 50 C Operating Humidity 80 Max R H Power Supply AA Alkaline Bat 2 each fimi The Value Leader 505 Instruction Manual Test Products International Inc 9615 SW Allen Blvd Beaverton OR 97005 4814 USA Ph 503 520 9197 Fax 503 520 1225 Test Product International Ltd 342 Bronte Street South Unit 9 Milton Ontario L9T 5B7 Ph 905 693 8558 Fax 905 693 0888 Test Products International UK Ltd Longley House East Park Crawley West Sussex RH10 6AP Ph 44 0 1293 561212 Fax 44 0 1293 813465 copyright 2006 Test Products International Inc
4. the START button is released le 2 When you are finished taking measurements release the START button Depress the MEMORY button once the LAST reading will be displayed Press the MEMORY button twice the MAX reading will be displayed Press the MEMORY button three times the MIN reading will be displayed Unit will auto power off after 5 seconds 3 CONTACT TACH OPERATION Measurement Procedure 1 2 4 5 Screw the shaft assembly to the optical end of the 505 Insert the cone or concave wheel that more closely matches the end of the component to be measured on the shaft assembly Press and hold the START button and then press the Contact button lower left on the 505 While pressing the START button hold the wheel against the end of the rotating shaft Read the RPM on the LCD Memory Recall Note The memory resets itself once the START button is depressed and stable measurements are displayed for 10 seconds or 12 revolutions whichever is longer The values are stored when the START buiton is released 1 2 When you are finished taking measurements release the START button Depress the MEMORY button once the LAST reading will be displayed Press the MEMORY button twice the MAX reading will be displayed Press the MEMORY button three times the MIN reading will be displayed Unit will power off after 5 seconds 4 SURFACE SPEED OPERATION Measurement Procedure
Download Pdf Manuals
Related Search