Owner/User Manual
Contents
1. Model PRO9051E LIESTE Owner s Manual So S 1 Channel Remote Car Starter 2 One Button Programmable RF Transmitters One Channel Receiver capable of accepting 4 transmitters External Superheterodyne Receiver Antenna w Push Button Switch amp LED PBS Unlock Output On Board Start Relay On Board Accessory Relay On Board Ignition 1 Relay On Board Ignition 2 Relay Ignition 2 Relay Selectable On or Off During Cranking On Board Parking Light Relay Ignition 3 Shock By Pass GM VAT Output relay required Tach Signal Learning Circuit and Safety Shutdown Circuits Alarm By Pass Output Accessory Outputs Pulse Before amp After Start During Crank amp After Shut Down Selectable Steady or Flashing Parking Lights for Run Indication Selectable 5 10 15 20 45 amp 60 Minute Run Time Selectable 1 Sec 3 5 Sec or 1 Sec Dbl 1 Sec Door Lock Output Pulse Car Finder Mode KEYLESS ENTRY The button on the transmitter can be used to unlock the vehicle s doors while running under control of the remote start Simply press and hold transmitter button for 3 seconds as you approach the vehicle and the doors will unlock NOTE Vehicle must have power door locks and this option must be connected at time of installation REMOTE CAR FINDER The Start button is also used to access the car finder mode This feature is particularly useful in a crowded parking lot where findin2. of 4
3. g your car may be difficult To access the car finder mode while within range of your car simply press and hold the button of your transmitter for three seconds The parking lights will begin to flash making your vehicle more visible The lights will stop automatically after 30 seconds If you wish to turn off the car finder mode prior to the expiration of the 30 second timer press and release button of your transmitter one time PATENTED www voxxintl com company patents 128 9352 1 of 4 REMOTE STARTING THE VEHICLE This unit will not start the vehicle if any one of the following situations exist The vehicle s hood lid is opened The gear shift selector is not in Park The brake pedal is depressed The safety control switch is in the Off position To start the vehicle press and release the Key Trunk button two times within 2 seconds The vehicle will start and remain running for the pre programmed 5 10 15 20 minute run cycle As a visual indication the parking lights will flash or remain on depending on the setting by your installation center When you arrive at the vehicle turn the ignition key to the ON position not the spring loaded start position then step on the brake pedal to disengage the remote starter The vehicle will continue to run but now on its own power NOTE The engine will stop running before the pre programmed run cycle has expired if you perform any one of the following func
4. his safety feature will alert you if an unauthorized transmitter has been programmed into your vehicle s security system without your knowledge Typically from the 128 9352 2 of 4 factory there will be 2 flashes and a pause repeated 3 times indicating that two transmitters are programmed into the system If you note additional flashes an additional transmitter may have been added without your knowledge or authorization If you notice a change in the transmitter LED report pattern you can correct this by looking up how to erase and reprogram your transmitters found in the transmitter programming guide This reprogram operation will erase all unauthorized or unwanted transmitters PROGRAMMING NEW OR REPLACEMENT TRANSMITTERS BANK 1 The Transmitter Model Name 1BPR Is Also Found On The Back Of The Transmitter Case And Uses A CR2032 Battery 1 Turn the ignition key to the on position 2 Press and Release the valet programming switch 3 times Siren Chirps 3 Press the Button of each transmitter you want programmed until you hear a chirp from the horn or siren or the parking lights flash 4 Turn the ignition switch off The above action programs the Start button in a 1 button system Transmitter battery replacement 1 Locate the slot along side the transmitter case and using a plastic tool or this coin separate the two transmitter case halves Slide the CR 2032 battery from the battery holder paying attention to the bat
5. tery orientation s side facing away from the circuit board Replace the battery with a new one Reassemble the case in reverse order of disassembly FUNCTION SETTING CHART To be completed by installer Run Time Min O Door Lock Timer Sec O Parking Lights Pulse O Steady O WARNING A running vehicle produces dangerous carbon monoxide gas which can be fatal if prolonged exposure occurs Be certain the vehicle is outdoors before activating the remote start function 128 9352 3 of 4 FCC COMPLIANCE his devices complies with Part 15 of the FCC rules and with RSS 210 of Industry anada Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including any interference that may cause undesired operation Warning Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Such modifications could void the user s authority to operate the equipment PATENTED www voxxintl com company patents To purchase replacement transmitters or to get additional product information go to www pursuitcarsecurity com 2014 Voxx Electronics Corporation 150 Marcus Blvd Hauppauge NY 11788 128 9352 128 9352 4
6. tions Press and release Key Trunk button on the keychain transmitter two times within 2 seconds Depress the brake pedal Open the vehicle s hood Place the unit in the safety control disabled mode PUSH BUTTON LED RECEIVER VALET OVERRIDE SAFETY CONTROL SWITCH The Push Button LED switch located in the receiver allows you to temporarily disable the remote starting function of the system This is recommended whenever the vehicle is being serviced To place the system in the service mode 1 With the system disarmed unlocked and the ignition switch off Press and Hold the Push Button found on the windsheild receiver in 2 Turn the ignition switch on off on off on off 3 The LED begins to flash two short flashes followed by one long flash and continues this pattern until returned to normal mode of operation This puts the unit into the R S Override mode indicating that the remote start is in the service mode and will not start from RF or any other input Posse or otherwise To Exit R S Override Mode 1 With the system disarmed Press and Hold the Push Button found on the windsheild receiver in 2 Turn the ignition switch on off on off on off 3 The LED turns off indicating that the R S unit is fully functional once again PROGRAMMED TRANSMITTER NOTIFICATION PTN Every time after Disarm when the ignition key is turned on the unit s LED will report the number of transmitters programmed into the system T
Download Pdf Manuals
Related Search