the HPS-120 User Manual - Industrial-Grade
Contents
1. RTS RS 232 Interface D_SUB 9 Pin Female Standard Bluetooth Specification Version 1 1 Frequency 2 400 2 4835GHz Hopping 1 600 Sec 1MHz Channel Space Modulation GFSK 1Mbps 0 5BT Gaussian Tx Power Max 20 Typical 16dBm Class 1 Rx Sensitivity 84dBm Antenna Interface SMA Female Antenna Gain Max 2dBi Power Supply 5 12Vdc Current Max 110mA Consumption Operation 20 75 C Temperature Size 35mm W x 65mm D x 16mm H Remark1 The default hardware configuration is for using CTS If you want to use DSR please contact us 2 2 RS 232 Interface 2 2 1 Pin out 5 4 3 2 1 ee ee ENE es E 98 7 6 2 2 2 Signals Pin Number Signal Direction Description 1 DCD Output Data Carrier Detect 2 TxD Output Transmitted Data 3 RxD Input Received Data 4 DSR N A Input Option Data Set Ready 5 GND N A Signal Ground 6 DTR Output Data Terminal Ready 7 CTS Input Clear to Send 8 RTS Output Request to Send 9 Vcc Input Power Supply Remark1 The default hardware configuration is for using CTS If you want to use DSR please contact us 2 3 Factory Setting The following is the factory setting of COM port Baud rate 9600 bps Data Bit 8 bit Parity Bit No parity Stop Bit 1 stop bit Flow control None 2 4 Display Status The following is status LED information OPR Red When HPS 120 is powered on i2. address and connection mode for the remote the local device won t be able to make a connection to the remote device 10
3. INDUSTRIAL GRADE MODEMS Your Communications Solutions Provider www industrial grade modem com USER MANUAL HPS 120 About this product Industrial Grade Modems works to provide you with reliable easy to use wireless serial communications technology Using the 2 4Ghz frequency range these products can achieve up to 1000m transmission distance and can also be used anywhere in the world without complicated licensing issues Modules feature sophisticated error correction technology and are suitable for use in harsh environments where there can be a lot of interference Temperature rated at 20 to 75C for extreme conditions Replace your RS232 serial communications cable with this wireless solution No complicated programming just plug in and go Suitable for PC to PC machine to PC or machine to machine applications Features Up to 3280 feet 1000m Transmission Distance No drivers required Temperature 20 to 75C Easy to use text menu interface Standard Serial Baud Rates up to 115Kps 5 13VDC Supply either through Pin 9 or Jack connector supplied Point to Point or Point to Multi Point configuration Pre configured out of the box for 9600Bps 8N1 communications Facility also to use AT commands to dial separate units Wireless RS232 Serial Kits include many features that are normally found on more expensive solutions including reliable data transfer with error correction and completely transparent protocols for exact data re
4. NAL SETTINGS cooonocccccnnococcnnnononcnnnnnn cnn nan donna anna rr 8 4 2 CONFIGURATION iii aa Renan ias 8 424 Start CORNGUIATION ci a ia 8 4 2 2 Usage Printing ota td a tt ake 8 4 2 3 Aller CONTIQUEATION cia o Lt ara 8 AI COMMAND E o 9 4 3 1 Command List for Local Davit arstin rerien iei a i R ae iea 9 4 3 2 Command List for Remote DeviCe ooooooocininicicinnncocinonoconnnnnnnannnnnnnn nn n nn nn rra 10 1 Introduction Thank you for purchasing a wireless HPS 120 The HPS 120 can be used as a component in many types of systems allowing them to communicate wirelessly with other Bluetooth products such as PC cards laptops handheld computers mobile phones and other HPS 120 The HPS 120 is a suitable component in new products as well as in existing products 1 1 Features Supports Bluetooth Serial Port Profile and Generic Access Profile No need of external host and software Easy of installation and use Supports configuration of the local device Supports configuration ofthe remote device via Over the Air Easy of maintenance Supports up to 100 meter Line of Sight 1 2 Package HPS 120 2 EA Antenna 2 EA A USB Cable for Power Supply A Manual 2 Specifications 2 1 General Baud Rate Up to 115 2kbps Recommend above 2 4kbps Supports 1 2 2 4 4 8 9 6 19 2 38 4 57 6 115 2kbps Coverage Up to 100 M Connection Point to Point Signal DCD TxD RxD GND CTS DSR DTR
5. between the local device and remote device Automatically Send changes from the local device to the remote device Automatically Apply changes at the remote device and reboot Automatically Item Syntax Description Remarks 1 Connecting AAddr lt Enter gt Set a connecting address for address remote device 2 Baud rate BBaud Rate Change the baud rate for the remote 3 COM port CCOM Port This is only valid in mode 2 4 PIN code EPIN lt Enter gt Authentication Off Type lt Enter gt Paired adapters should Authentication On Type up to 11 characters have a same PIN code 5 Flow control FFlow Control Set the Flow control for remote 6 Connection MMode Set a connection mode for mode remote 7 Friendly name NName lt Enter gt Set a friendly name up to 11 characters for remote 8 Parity Bit PParity Set the parity bit 0 None 1 Odd 2 Even 9 Stop Bit SStop Set the stop bit 0 1 Stop 1 2 Stop 10 View V Display configuration information for remote 11 Exit X Save changes and return to main menu 12 Usage Print the usage Remarks1 To configure a remote device via over the air a local device must be able to make a connection to the remote device Remarks2 You can change a PIN code for the remote and local device as follows Change a PIN for remote at the local gt Apply it gt Change a PIN for local and apply it Remarks3 Once you change a connecting
6. in connector 3 3 Install Procedure Step 1 Assemble a provided antenna to HPS 120 body Step 2 Plug a HPS 120 into the COM port of device Step 3 Power on Step 4 Configure the HPS 120 if necessary 4 Usage You can change the configuration of HPS 120 using Hyper Terminal 4 1 Hyper Terminal Settings Baud Rate 9600 bps Data Bit 8 Parity Bit None Stop Bit 1 Flow Control None Emulation VT 100 4 2 Configuration 4 2 1 Start Configuration Step 1 Plug a HPS 120 into a COM port of PC And Power it on Step 2 Open a Hyper Terminal and set it up Step 3 Push the RST button on HPS 120 If you enter the configuration mode successfully LNK LED will be flashing every second Step 4 Hit the lt Enter gt key 5 second later Step 5 Change the configuration of HPS 120 with commanas if necessary 4 2 2 Usage Printing If you are in the configuration mode type key You will see the usage All commands and parameters are case sensitive And you cannot use a lt Backspace gt 4 2 3 After Configuration After finishing the configuration you have to execute a command X to apply changes 4 3 Command Set 4 3 1 Command List for Local Device Item Syntax Description Remarks 1 Connecting AAddr lt Enter gt Set a remote device A local and remote address address for a wireless BD_ADDR always need to connection be difference 2 Baud rate BBaud Rate Change the ba
7. plication These units can work in environments where there is other wireless equipment harsh industrial locations with electrical noise indoor or outdoor applications with low power consumption Kit includes two HPS 120 units two 500m or 1000m antennas power cable and manual Industrial Grade Modem 41 Wightman Ct Dana Point CA 92629 Phone 949 481 6516 FAX 949 270 1500 1 2 3 Table of Contents INTRODUCTION vareae aai hice dis inaa eiae A Eae Ana TA Te PANNA EE EA ANTE AAT AASE 3 Eie FEATURE Sune a r a e e a 3 EL PACKAGE E EE E E E E A E E T EAE A E E T 3 SPECIFICATIONS stc iooticclacionnicrenanne dcir colado A o CNEA de CRAEN NAASE NIRSA NIE LEENE AORERE RINA 4 a a GENERAL toe uh AA A ee eee ee E a E R 4 2 26 RS 232 INTERFACE sneri A EA A E dd did A 5 DDT ANUN 5 PA El AA E EE E E T E E E es E RA Eas 5 2 0 FACTORY SETIN n sac nd E A 5 24 DISPLAY STATUS o Seaia dd dd iaa 6 2 02 RESET BUTIN ino ona ia EA a A EEE 6 2 5 1 Enter Configuration MOIO erT T A TA 6 2 5 2 Exit Configuration MOJE coomiccconnccccconocicccononcccconanncccn nn nnn canon nn naar rra 6 PS 0 A Zoey A E OA 6 HARDWARE INSTALLATION ccccceeseeeeeeeeeeeeeeeeeeeeneeeeeeensseeeeenssseeeeeseeeeeseeseeeeseeeseeeeenssanens 7 3 1 HARDWARE DESCRIPTION iieiea airis Xai tee k AAA ERE AiE Eaa aAa TAASEN NEA 7 3 23 POWER SUPPLY to E E E teas 7 3232 INSTALL PROCEDURE vindeiras ea AT Ness EA iia aai nage 7 USAGE iniciarte da aida 8 4 1 HYPER TERMI
8. t is turned on or flashing LNK Green When a wireless link is on it is turned on If HPS 120 is in the configuration mode it will be flashing every second 2 5 Reset Button The RST button has the following functions Enter Exit the configuration mode Restore the factory settings e Disconnect and reconnect a wireless connection 2 5 1 Enter Configuration Mode When the LNK LED is OFF push the RST button When the LNK LED is ON you have to push the RST button twice to enter the configuration mode If you enter the configuration mode successfully LNK LED will be flashing every second And HPS 120 COM port will be stored the factory settings 2 5 2 Exit Configuration Mode You can have two options to exit the configuration mode Exit the configuration mode by software Type X Exit the configuration mode by the RST button Push the RST button 2 5 3 Re connection When the LNK LED is on you can push the RST button to disconnect and reconnect a wireless link Waning If you push the RST button the COM port of HPS 120 will be stored the factory setting 3 Hardware Installation 3 1 Hardware Description RST Button RS 232 Connector OPR LED USB Cable for Power Antenna Connector 3 2 Power Supply You can supply power to the HPS 120 as follows Use an AC DC converter Output Power 5 12Vdc 300mA Use a provided USB cable You can supply power via 9 pin of D_SUB 9 P
9. ud rate Baud Rate 0 1200 1 2400 2 4800 3 9600 4 19200 5 38400 6 57600 7 115200 3 COM port CCOM Port This is only valid in connection mode 2 4 PIN code EPIN lt Enter gt Authentication Off Type lt Enter gt Paired adapters should Authentication On Type up to 11 characters have a same PIN code 5 Flow control FFlow Control Set the Flow control 0 None 1 DTR DSR 3 Hardware amp DTR DSR Hardware 2 6 Connection Mmode Set a connection mode 0 1 1 Mode 1 WAIT Mode mode 2 REGISTER and CONNECT Mode 7 Friendly name Nname lt Enter gt Set a friendly name up to 11 characters 8 Command for O Enter configuration mode the remote for the remote 9 Parity Bit Pparity Set the parity bit 0 None 1 Odd 2 Even 10 Stop Bit Sstop Set the stop bit 0 1 Stop 1 2 Stop 11 View V Display configuration information 12 Exit X Apply changes 13 Usage Print the usage Waning If you push the RST button the COM port of HPS 120 will be stored the factory setting 4 3 2 Command List for Remote Device To change the configuration for a remote device via over the air firstly you have to use a command O at the local device The following are a procedure for changing configuration of remote device via over the air e Configure a remote device at the local device O Save changes at the local device e Make a connection
Download Pdf Manuals
Related Search