DAS1100 Distress alert system
Contents
1. procedure Audible Interference through speaker Occasionally other electrical items in a room TVs radios etc can interfere with the main units speaker Try moving the unit or the suspected item affecting it to a different location Poor sound quality on message Try re recording your message speaking Clearly into the main unit Keyfob low battery indicator The light on the keyfob will turn red instead of green when the Yale button is pressed Replace battery Your nominated contact s cannot acknowledge the call The call acknowledgement will only work if your nominated contact is using a touch tone DTMF phone Important notes To indicate low battery on the main unit when running on batteries only the main unit red light will be on permanently Plug in mains adaptor and replace backup batteries The system is not waterproof and is only intended for indoor dry usage This product is purely a communication device and should not be used as a substitute for a specific medical or emergency alarm If you have any special requirements you should always consult a medical orofessional for appropriate advice on tele medical equipment This device should never be used to dial emergency telephone numbers i e 999 An ASSA ABLOY Group brand Keep the main unit away from direct sunlight or hot surfaces Only use the supplied power adaptor Other adaptors may damage the main unit Always inform your nomi2. DAS1100 Distress alert system e Alerts friends and family at the press of a button e Allows independence while keeping you in touch e Helos you maintain your active lifestyle User Manual Keep this manual safe for future reference An ASSA ABLOY Group brand ASSA ABLOY Step 1 Connection Step 2 Turn on main unit Lift cover at rear of unit u a aaO e LAL ee a on _ oFF Telephone wall outlet Telephone Step 3 Red light stops flashing Step 4 Press keyfob button amp stays lit Step 6 Set maximum 3 phone numbers Input phone numbers C 2 gt including area codes 1x To set up other numb Step 5 Red light will turn off ers use same sequence but replace with 2 and 3 button at this stage Step 7 Recording voice message Step 8 Play back voice message Press P to play back pre recorded message Hold both buttons together gt and speak into microphone in the main unit for 10 seconds to A N Repeat step 7 if required Set up is now complete Package content 1 x Main unit 1 x Remote keyfob battery pre fitted 1 x 6V DC adaptor 1 x Necklace holder for keyfob 1 x Telephone cable 1 x Telephone splitter Set up Connection Remove all components from packaging Open the cover on back of the main unit and plug in one end of the supplied teleohone cable Connect the other end into the supplied telephone splitter Remove the existing te
3. ining 2 contact numbers using buttons 2 and 3 accordingly If you make a mistake these numbers can be overwritten using the same process Recording your voice message You can now record your voice message which can be up to 10 seconds long This is the message that the system will play if triggered Try to ensure that the message is as detailed as possible To record the message press and hold the microphone button and the hash button together and speak clearly into the main unit When you have finished recording release the buttons To play back your message press the play button If you want to re record your message repeat the process above Operation Using your distress alert system If you need to activate your system press the Yale button either on a keyfob or the main unit The system will beep 10 times then after a short delay will automatically dial the preset numbers in the order that you set them beginning with the telephone number you assigned to button 1 The Speaker on the main unit will playback your pre recorded message repeatedly Each number will be dialled 5 times with each call lasting 45 seconds if not acknowledged Ifyou accidentally press the Yale button and activate the system you can cancel the alert by switching the main unit OFF and then back ON After the red lignt goes out the system is ready to use Instructions for your nominated contacts When an
4. lephone cable from the wall outlet and plug into the telephone splitter Then plug the telephone splitter into the telephone wall outlet Connect the power adaptor to the main unit and plug into the mains Insert optional 4 x AAA batteries if back up power Is required for the main unit Programming the keyfob s Turn the system ON when you are ready to proceed with the set up The red light will then flash for 15 seconds while initialising Afterwards the light will remain red for 1 minute during which time you can program or learn in your keyfob s maximum of 3 Now press the Yale button on your keyfob once Your system will resoond with a beep to indicate that learning is successful Allow 3 seconds before pressing further keyfobs for learning in If the red light goes out the main unit is no longer in learn mode In order to return to learn mode turn the main unit OFF and then back ON again Wait for the static red light and continue your learning process Setting contact telephone numbers After the red light goes out you can program up to 3 teleohone numbers landline or mobile First press the handset and star button followed by button 1 this will be the first contact number used by the system Then key in the full telephone number including the area code Finally press the handset and star button again to finish the process Repeat this process for each of your rema
5. nated contact s prior to their inclusion and agree a particular course of action upon their receiving your automated call Specification e Frequency 433 92MHz e Range 30 metres free line of sight e Power supply Main Unit 6V DC adaptor or 4 x AAA alkaline batteries backup power not included Remote Keyfob 12V A238 battery Adaptor information Input 100 240V 50 60Hz 0 2A Output 6 0V 1000mA Consumer helpline If you have a question concerning your system please call the helpline on 0871 70 30 630 UK only Lines open 8am 5pm Monday Friday Calls cost approximately 10 9 per minute from a UK landline From outside the UK please call 44 0 1902 635998 CEO Yale Note Waste electrical products should Yale not be disposed of with household waste Please recycle where facilities exist Check with your local authority or retailer for recycling advice School Street Willenhall West Midlands WV13 3PW Tel 44 0 1902 364606 Fax 44 0 1902 364692 email info yale co uk www yale co uk ASSA ABLOY E1 04 07
6. odes change the 4 dip switches found underneath the cover to another random combination Next turn the main unit OFF then ON and wait for the static red light Press the Yale button on any keyfob 3 times to clear all programming Clearing your nominated contact numbers Press the following key sequence on the main unit Clearing your voice message Press the microphone button and the hash key together and then release ASSA ABLOY Ltd School Street Willenhall West Midlands England WV13 3PW EC Declaration of Conformity We ASSA ABLOY Ltd School Street Willenhall West Midlands England WV13 3PW declare under our sole responsibility that the following product s Model DAS1100 DAS11 is are in conformity with the following relevant harmonised standards EN 60950 1 2001 A11 2004 ETSI EN 301 489 3 V 1 4 1 2002 08 ETSI EN 300 220 3 V 1 1 1 2000 09 TBR 21 following the provisions of Council Directive 1999 5 EC on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity Name John Ward Position Director Signature St pr We Date 20 04 07 On behalf of ASSA ABLOY Ltd Additional Information Troubleshooting Unit triggers without cause There may be interference from another Keyfob or wireless equipment nearby Reset the keyfob ID code and re learn it into the system refer to reset
7. y of your nominated contacts receives a call they will hear your recorded message being played repeatedly To acknowledge the call they must press any number on their telephone keypad This will then activate a 2 way communication with you If you are near the main unit you will be able to speak to them via the built in soeaker microphone if you are too far from the main unit the microphone may not pick up your voice The 2 way communication will last for 50 seconds before 3 warning beeps indicate that the call will end within 10 seconds To extend the call for a further 60 seconds your nominated contact should press any number on their telephone keypad After the call is ended the system is ready to use Testing your system To ensure your system is set up correctly test it fully before using Ensure your nominated contacts are aware that you are testing and then activate to check all functions If your system doesn t work first check all connections and then reset using the reset procedure Then work through the set up procedure again This is a wireless system with a limited transmission range Try triggering your keyfob s in different parts of your house Doors walls and other wireless equipment may reduce the range Make a note of where the signal cannot be consistently received by the main unit and do not use keyfob s in these areas Reset procedure Resetting keyfob programming To reset keyfob ID c
Download Pdf Manuals
Related Search